COMMUNICATION TECHNIQUE N TC0521 Ed. 01 OmniPCX Enterprise Nb de pages : 17 Date : 19-01-2004 URGENTE NON URGENTE TEMPORAIRE DEFINITIVE OBJET : REFORMATAGE ET RECHARGEMENT DE LA Cette communication technique a pour but de fournir une procédure de rechargement des binaires e- MGD en R5.1 dans le cas d'une altération de la NAND Flash d'une e-mgd. 1
REFORMATAGE ET RECHARGEMENT DE LA OmniPCX Enterprise SOMMAIRE 1. BUT...3 2. EFFACEMENT ET REFORMATAGE DE LA NAND FLASH E-MGD...3 3. RECHARGEMENT DES BINAIRES E-MGD...5 Ed. 01 / 19-01-2004 1 TC0521
OmniPCX Enterprise REFORMATAGE ET RECHARGEMENT DE LA TC0521 2 Ed. 01 / 19-01-2004
REFORMATAGE ET RECHARGEMENT DE LA OmniPCX Enterprise 1. BUT Cette communication technique a pour but de fournir une procédure de rechargement des binaires e-mgd en R5.1dans le cas d'une altération de la NAND Flash d'une e-mgd. Le rechargement de la NAND Flash d'une e-mgd avec l'omnipcx Enterprise PC Installer s'effectue en deux phases : 1 Effacement et reformatage de la NAND Flash e-mgd. 2 Rechargement des binaires e-mgd. 2. EFFACEMENT ET REFORMATAGE DE LA NAND FLASH E-MGD 1 Connecter la carte GD/GA et le PC Serveur avec un câble Ethernet croisé. 2 Démarrer l'omnipcx Enterprise PC Installer V2.15. Choisir le type d'installation Binaire GD/GA dans le menu Type d installation. Cliquer sur Valider dans la fenêtre Paramètres d installation. Les binaires e-mgd (dépendants de la version) doivent être présents dans le répertoire /dhs3mgr/"version"/pcmao/boot_res/dhs3bin/downbin/emg. Ed. 01 / 19-01-2004 3 TC0521
OmniPCX Enterprise REFORMATAGE ET RECHARGEMENT DE LA 3 Démarrer la carte GD/GA en mode LOLA. Positionner les dip switchs 1, 2 et 4 sur ON, le dip switch 3 sur OFF. Démarrer la carte GD/GA en Position Contrôleur (Position 0 du Rack). Dans ce mode, le transfert des fichiers peut être visualisé dans la fenêtre Paramètres du client de l'omnipcx Enterprise PC Installer. TC0521 4 Ed. 01 / 19-01-2004
REFORMATAGE ET RECHARGEMENT DE LA OmniPCX Enterprise 4 Les différentes phases d'effacement et de reformatage peuvent être visualisées par la LED CPU de la carte GD/GA : Phase du bios 2 x ON/OFF (250ms)/ 1 OFF ( 2 s) Phase de chargement du Linux.ram 4 x ON/OFF(250ms)/ 1 OFF ( 2 s) Phase d'effacement et de formatage de la NAND FLASH Fixe ON Phase de fin de formatage de la NAND FLASH Clignotement rapide (50 ms/ 50 ms) 5 La fin de formatage de la FLASH est visualisée sur le port de configuration V24 par le message : Welcome to PeeWeeLinux (none) login: 6 Arrêter la carte GD/GA avec l'interrupteur On/Off et attendre que la LED power passe au rouge fixe. 7 Arrêter l'application OmniPCX Enterprise PC Installer sur le PC Serveur. 3. RECHARGEMENT DES BINAIRES E-MGD 1 Redémarrer l'omnipcx Enterprise PC Installer V2.15. Choisir le type d'installation Binaire GD/GA dans le menu Type d installation. Cliquer sur Valider dans la fenêtre Paramètres d installation ; voir point 2 du 2) 2 Démarrer la carte GD/GA en mode GD. Positionner le dip switch 2 sur ON, les dip switchs 1, 3 et 4 sur OFF. Démarrer la carte GD/GA en Position Contrôleur (Position 0 du Rack). Dans ce mode une visualisation du transfert des fichiers est possible sur le port de configuration V24 (9600 8-N-1) et également dans la fenêtre Paramètres du client de l'omnipcx Enterprise PC Installer. Ed. 01 / 19-01-2004 5 TC0521
OmniPCX Enterprise REFORMATAGE ET RECHARGEMENT DE LA TC0521 6 Ed. 01 / 19-01-2004
REFORMATAGE ET RECHARGEMENT DE LA OmniPCX Enterprise Exemple de rechargement correct sur le port de configuration V24 Alize BIOS Monitor *** BIOS Version 3EH30227DQAA bios100/008.016 *** *** Generated on Mar/20/2003 at 09:21 *** memory test started lng=133169152 with 0 YOU CAN strike Ctrl B to enter in BIOS monitor during several seconds from NOW! running flash(soldered=1 socket=0)=1,bioscase:4,biosv24:0,verrou=1,algonor=1,size=1,base=3ff80000 DIMM characteristics->: JEDEC Manu ID:. Memory type(edo,fpm..):0x04 # of row address:12 # of col address 10 # of module row 1 PCI: Using configuration type 1 PCI: Probing PCI hardware PCI:scan_bus for bus 0 PCI:bus=00h,devfn=00h,[vendor:device]=[1022h/3000h] PCI:bus=00h,devfn=60h,[vendor:device]=[100bh/0020h] PCI:bus=00h,devfn=98h,[vendor:device]=[1064h/2101h] PCI:scan_buses with 00h secondary buses PCI:command =000003ffH for device 00:00 PCI: Assigning I/O space fc00-fcff for 00:60 BAR=00000010 PCI:Assign memory space bffff000h to bfffffffh for device 00:60 PCI:command =000003ffH for device 00:60 PCI:Assign memory space bfffd000h to bfffdfffh for device 00:98 PCI: Assigning I/O space fd00-fd1f for 00:98 BAR=00000014 PCI: Unable to handle I/O allocation for 00:98 (ff04) BAR=00000018 PCI:command =000003ffH for device 00:98 assigning irq10 to xchange B0 = 17 DRCTMCTL = 1e DRCCTL = 18 DBCTL = 11 Set external RTC Set Internal RTC No external RTC detected CMOS is available Xchange PCI mem base OK: 00000000 Xchange PCI IO base OK: 00000000 Xchange irq OK: 0a PCI command read for natsemi : 00000347 PCI Master Bit Setting... pci_command set to:0357 0000 0080 009f 002f 00ef 0037, IRQ 12 eth0: Transceiver status 0x00007869 advertising 000005e1 Flashfx version:520.001.001 NAND flash drive No. 0 successfully mounted NAND Flash Comfiguration: CPU size : 32 MBytes free spare blocks: 38 XMEM size : 0 MBytes NAND Flash Details: chip #0 : Type=TC58256 Id=9875H Size=32(MBytes) Unit size=16384 Page Size=512 time :sec=09,min=12,hour=11,dow=02,date=15,month=12,year=00 time :sec=12,min=12,hour=11,dow=02,date=15,month=12,year=00 ALIZE informations : Memory Detected : 131072 Ko Flash Detected DaughterBoard Detected DSP Voip Found : 1 XCHANGE Detected XCHANGE Chip Initialization OK Ethernet Found : 1 Ethernet Chip Initialization OK Hard Disk Not Detected PCM11 selected CPU at 133 mhz check lock RTC value of DIL switch 02 Ed. 01 / 19-01-2004 7 TC0521
OmniPCX Enterprise REFORMATAGE ET RECHARGEMENT DE LA test the BATMODE Static Boot from hard disk #0 (3) unable to boot on DISK :00000005 Static Boot from No Boot Device selected (0) Static Boot from flash NAND mother (1) unable to boot on NAND flash drive 0 unable to boot on flash NAND Static Boot from ethernet (4) eth0: Setting 1 (0 half 1 full) based on negotiated link capability. IP address determination ============================ BOOTP request in progress -> 0:80:9f:2f:ef:37 *RcvTO,TOIPRcv,Bootp resp IP addr src :10.24.1.20 bootp server and TFTP server are the same TFTP server IP addr ( siaddr) : 10.24.1.20 eth source address=0:50:da:81:ef:24 bootfile = /DHS3bin/downbin/emg/binmgstart Netmask : 255.255.0.0 Our Hostname : OXE_1 (10.24.1.21) Domain name : lcatel.a4400.0 My IP address 10.24.1.21 My SUBNET mask 255.255.0.0 TFTPLOAD STARTED using ip=10.24.1.20 - Bootp Server PARIS-A63YI55YS - File Name /DHS3bin/downbin/emg/binmgstart size of last packet: 141 TFTPLOAD COMPLETE - file size 141 cmd received : /DHS3bin/downbin/emg/binmgvmlinux;763904;BIN;1048576;1048576 /DHS3bin/downbin/emg/binmgrdimg;5162683;RAMDISK;4194304;0 boot;0;boot;0;1048576 size of file loaded : 0000008dH at 00006624H j= 0 file-fct type= 7,file name= /DHS3bin/downbin/emg/binmgvmlinux,length= 763904,address=1048576 start=1048576 j= 1 file-fct type= 1,file name= /DHS3bin/downbin/emg/binmgrdimg,length= 5162683,address=4194304 start=0 j= 2 file-fct type= 5,file name= boot,length= 0,address=0 start=1048576 j= 3 file-fct type= 0,file name=,length= 0,address=0 start=0 j= 4 file-fct type= 0,file name=,length= 0,address=0 start=0 j= 5 file-fct type= 0,file name=,length= 0,address=0 start=0 j= 6 file-fct type= 0,file name=,length= 0,address=0 start=0 j= 7 file-fct type= 0,file name=,length= 0,address=0 start=0 j= 8 file-fct type= 0,file name=,length= 0,address=0 start=0 j= 9 file-fct type= 0,file name=,length= 0,address=0 start=0 config action number=3 TFTPLOAD STARTED using ip=10.24.1.20 - Bootp Server PARIS-A63YI55YS - File Name /DHS3bin/downbin/emg/binmgvmlinux......size of last packet: 14 TFTPLOAD COMPLETE - file size 763918 WARNING: downloaded size file # from command file TFTPLOAD STARTED using ip=10.24.1.20 - Bootp Server PARIS-A63YI55YS - File Name /DHS3bin/downbin/emg/binmgrdimg........................size of last packet: 187 TFTPLOAD COMPLETE - file size 5162683 11581=total packets received 11584=total packets transmitted 6460074=total bytes received 742484=total bytes transmitted 0=bad packets received 0=packet transmit problems 0=no space in linux buffers 0=no space available in linux 0=multicast packets received 0=collisions 0=length_errors TC0521 8 Ed. 01 / 19-01-2004
REFORMATAGE ET RECHARGEMENT DE LA OmniPCX Enterprise 0=receiver ring buff overflow 0=recved pkt with crc error 0=recv'd frame alignment error 0=recv'r fifo overrun 0=receiver missed packet 0=tx_aborted_errors 0=tx_carrier_errors 0=tx_fifo_errors 0=tx_heartbeat_errors 0=tx_window_errors 0=rx_compressed 0=tx_compressed start kernel at 00100000 Shutdown of the interface 0 =00000000 init ethernet interface 1 not done Watch dog started Linux version 2.2.18-rtl (alzcpl@cu5s132) (gcc version 2.95.2 19991024 (release)) #45 Fri Jan 31 13:52:58 MET 2003 Calibrating delay loop... 65.74 BogoMIPS Memory: 123364k/131072k available (632k kernel code, 412k reserved, 1584k data, 36k init) Checking if this processor honours the WP bit even in supervisor mode... Ok. ShutOK cleared! Dentry hash table entries: 16384 (order 5, 128k) Buffer cache hash table entries: 131072 (order 7, 512k) Page cache hash table entries: 32768 (order 5, 128k) CPU: AMD 486 DX/4-WB stepping 04 Checking 386/387 coupling... OK, FPU using exception 16 error reporting. Checking 'hlt' instruction... OK. POSIX conformance testing by UNIFIX PCI: Using configuration type 1 PCI: Probing PCI hardware Linux NET4.0 for Linux 2.2 Based upon Swansea University Computer Society NET3.039 NET4: Unix domain sockets 1.0 for Linux NET4.0. NET4: Linux TCP/IP 1.0 for NET4.0 IP Protocols: ICMP, UDP, TCP TCP: Hash tables configured (ehash 131072 bhash 65536) 802.1Q VLAN Support v1.0 (c) 2000 Ben Greear (GPL) vlan Initialization complete. Starting kswapd v 1.5 Serial driver version 4.27 with no serial options enabled ttys00 at 0x03f8 (irq = 4) is a 16550A ttys01 at 0x02f8 (irq = 3) is a 16550A pty: 256 Unix98 ptys configured RAM disk driver initialized: 16 RAM disks of 20480K size RAMDISK: Compressed image found at block 0 VFS: Mounted root (ext2 filesystem). Freeing unused kernel memory: 36k freed Warning: unable to open an initial console. Initial console created for init RTLinux Extensions Loaded (http://www.fsmlabs.com/) Starting watchdog timer daemon using /dev/rtf3 modprobe: modprobe: Can't locate module char-major-4 INIT: version 2.78 booting Remounting root read-write... modprobe: modprobe: Can't locate module char-major-4 e-mgd board found - setting up ramdisk Remount - Forces the media to be remounted Datalight FlashFx V4.05.309 Copyright (c) 1993-2000 Patent US#5860082 Disk Remounted e2fsck 1.19, 13-Jul-2000 for EXT2 FS 0.5b, 95/08/09 /dev/fla: clean, 11/7776 files, 1000/31062 blocks /dev/fla on /mnt/flash type ext2 (rw) INIT: Entering runlevel: 3 e-mgd version 16.7 Media Gateway Software R5.1 loading.. No password file found - using default password list Network configured successfully. Duplex mode : auto-negociation BIOS updater is now working... getting current version information Ed. 01 / 19-01-2004 9 TC0521
OmniPCX Enterprise REFORMATAGE ET RECHARGEMENT DE LA Check if we need to update with bios 3EH30227DQAA bios100/008.016... Reboot after bios update is enabled... ----- RetrieveFlashNorInfo ----- NOR VERSION : Bios Version in soldered NOR flash : 3EH30227DQAA bios100/008.016 len = 28 - Flash Nor Informations - Flash AMD Size : 512 Kbytes Number of sectors : 11 ----- CompareBiosVersions ----- CURRENT=008.016 FILE=008.016 ******************************* * NO bios Update is necessary * ******************************* Basic registers of MII PHY #1: 3100 786d 2000 5c21 05e1 45e1 0007 2801. Link status: active. loading modules - please wait... Real-Time Linux Dynamic Memory Manager 4.00 RTLinux System Call loaded Starting USER_PROCCES using fifo 7 6 Waiting for User Process registration Starting VG_PROCCES using fifo 5 4 Waiting for Vg Process registration Starting monitor using fifos 1/2 Alcatel kernel module loading...(break=0) Application User Process registered Application VG Process registered Main task created thread_id=0xc5291e00 stack address=0xc528cd58 stack bottom address = 0xc5288000 watchdogd now in real time mode DSP Manager OK Fast Socket Initialization... Ok ============ continue_rack_init ============== DIL SWITCH VALUE = 0x2 1024 Ko - BUFFER ALLOCATED MGD - RACK CONSTRUCTION @ MAC : 00:80:9f:2f:ef:37 @ IP : 10.24.1.21 net mask : 255.255.0.0 gateway : 0.0.0.0 tftp server : 10.24.1.20 call server : 0.0.0.0 default crystal number : 3 (Dynamic allocation) vlan id : -1 default priority : 0 default dscp : 0 duplex mode : auto-negociation Module MG Loaded watchdogd now in normal mode RTLinux System Load 1.00 init_module GPA ->insmod GPA Module GPA loaded Module APA loaded Module SLAC loaded Module DDI loaded Module UAI loaded Module SLI loaded Insert INTX module Insert ISDN module Module BRA loaded Module PRA loaded Module PRACCS loaded Module PRA_T1CAS loaded Module PRA_E1CAS loaded ->init_module emga ==> emgd_emga & emgd_gpa module types created! Module emgd_emga loaded Module emgd_gpa loaded Module MIX loaded Module ATL loaded Module RESCUE loaded PUC_device registered Module DPNSS loaded Module DSPx_LOAD loaded Module UASIM loaded TC0521 10 Ed. 01 / 19-01-2004
REFORMATAGE ET RECHARGEMENT DE LA OmniPCX Enterprise /mnt/flash/local/boot_from.cfg not found. Assuming boot from ethernet Downloading /DHS3bin/downbin/emg/binmg from 10.24.1.20 Downloading binmgrdimg and binmglinux Downloading /DHS3bin/downbin/emg/binmgrdimg from 10.24.1.20 Downloading /DHS3bin/downbin/emg/binmglinux from 10.24.1.20 binmglinux and binmgrdimg successfully downloaded Copying binmg, binmglinux, and binmgrdimg in flash. This process may take several minutes. Please do NOT reboot during the flashing process. watchdogd now in real time mode GRUB version 0.5.92 (640K lower / 4096K upper memory) [ Minimal BASH-like line editing is supported. For the first word, TAB lists possible command completions. Anywhere else TAB lists the possible completions of a device/filename. ESC at any time exits. ] grub> install=(vd0)/boot/pstage1 d (vd0) (vd0)/boot/stage2 0x8000 p (vd0)/boot/ grub.cnf grub> quit Rebooting in 5 seconds to try the new version. Reboot on Download new binaries INIT: Switching to runlevel: 6 INIT: Sending processes the TERM signal Alcatel kernel module cleanup...ok Saving e-mgd configuration files... Saving System Clock in Hardware Clock... No backtrace Sending all processes the TERM signal... Sending all processes the KILL signal.. Unmounting file systems Restarting system. ShutOK cleared! Alize BIOS Monitor *** BIOS Version 3EH30227DQAA bios100/008.016 *** *** Generated on Mar/20/2003 at 09:21 *** memory test started lng=133169152 with 0 YOU CAN strike Ctrl B to enter in BIOS monitor during several seconds from NOW! running flash(soldered=1 socket=0)=1,bioscase:4,biosv24:0,verrou=1,algonor=1,size=1,base=3ff80000 DIMM characteristics->: JEDEC Manu ID:. Memory type(edo,fpm..):0x04 # of row address:12 # of col address 10 # of module row 1 PCI: Using configuration type 1 PCI: Probing PCI hardware PCI:scan_bus for bus 0 PCI:bus=00h,devfn=00h,[vendor:device]=[1022h/3000h] PCI:bus=00h,devfn=60h,[vendor:device]=[100bh/0020h] PCI:bus=00h,devfn=98h,[vendor:device]=[1064h/2101h] PCI:scan_buses with 00h secondary buses PCI:command =000003ffH for device 00:00 PCI: Assigning I/O space fc00-fcff for 00:60 BAR=00000010 PCI:Assign memory space bffff000h to bfffffffh for device 00:60 PCI:command =000003ffH for device 00:60 PCI:Assign memory space bfffd000h to bfffdfffh for device 00:98 PCI: Assigning I/O space fd00-fd1f for 00:98 BAR=00000014 PCI: Unable to handle I/O allocation for 00:98 (ff04) BAR=00000018 PCI:command =000003ffH for device 00:98 assigning irq10 to xchange B0 = 17 DRCTMCTL = 1e DRCCTL = 18 DBCTL = 11 Set external RTC Set Internal RTC No external RTC detected CMOS is available Xchange PCI mem base OK: 00000000 Xchange PCI IO base OK: 00000000 Xchange irq OK: 0a PCI command read for natsemi : 00000347 PCI Master Bit Setting... pci_command set to:0357 0000 0080 009f 002f 00ef 0037, IRQ 12. eth0: Transceiver status 0x00007869 advertising 000005e1 Flashfx version:520.001.001 Ed. 01 / 19-01-2004 11 TC0521
OmniPCX Enterprise REFORMATAGE ET RECHARGEMENT DE LA NAND flash drive No. 0 successfully mounted NAND Flash Comfiguration: CPU size : 32 MBytes free spare blocks: 38 XMEM size : 0 MBytes NAND Flash Details: chip #0 : Type=TC58256 Id=9875H Size=32(MBytes) Unit size=16384 Page Size=512 time :sec=42,min=15,hour=11,dow=02,date=15,month=12,year=00 time :sec=45,min=15,hour=11,dow=02,date=15,month=12,year=00 ALIZE informations : Memory Detected : 131072 Ko Flash Detected DaughterBoard Detected DSP Voip Found : 1 XCHANGE Detected XCHANGE Chip Initialization OK Ethernet Found : 1 Ethernet Chip Initialization OK Hard Disk Not Detected PCM11 selected CPU at 133 mhz check lock RTC value of DIL switch 02 test the BATMODE Static Boot from hard disk #0 (3) unable to boot on DISK :00000005 Static Boot from No Boot Device selected (0) Static Boot from flash NAND mother (1) BOOT Sector Found on NAND Flash Drive #0 Shutdown of the interface 0 =00000000 init ethernet interface 1 not done Watch dog started Linux version 2.2.18-rtl (alzcpl@cu5s132) (gcc version 2.95.2 19991024 (release)) #45 Fri Jan 31 13:52:58 MET 2003 Calibrating delay loop... 65.74 BogoMIPS Memory: 123364k/131072k available (632k kernel code, 412k reserved, 1584k data, 36k init) Checking if this processor honours the WP bit even in supervisor mode... Ok. ShutOK cleared! Dentry hash table entries: 16384 (order 5, 128k) Buffer cache hash table entries: 131072 (order 7, 512k) Page cache hash table entries: 32768 (order 5, 128k) CPU: AMD 486 DX/4-WB stepping 04 Checking 386/387 coupling... OK, FPU using exception 16 error reporting. Checking 'hlt' instruction... OK. POSIX conformance testing by UNIFIX PCI: Using configuration type 1 PCI: Probing PCI hardware Linux NET4.0 for Linux 2.2 Based upon Swansea University Computer Society NET3.039 NET4: Unix domain sockets 1.0 for Linux NET4.0. NET4: Linux TCP/IP 1.0 for NET4.0 IP Protocols: ICMP, UDP, TCP TCP: Hash tables configured (ehash 131072 bhash 65536) 802.1Q VLAN Support v1.0 (c) 2000 Ben Greear (GPL) vlan Initialization complete. Starting kswapd v 1.5 Serial driver version 4.27 with no serial options enabled ttys00 at 0x03f8 (irq = 4) is a 16550A ttys01 at 0x02f8 (irq = 3) is a 16550A pty: 256 Unix98 ptys configured RAM disk driver initialized: 16 RAM disks of 20480K size RAMDISK: Compressed image found at block 0 VFS: Mounted root (ext2 filesystem). Freeing unused kernel memory: 36k freed Warning: unable to open an initial console. Initial console created for init RTLinux Extensions Loaded (http://www.fsmlabs.com/) Starting watchdog timer daemon using /dev/rtf3 modprobe: modprobe: Can't locate module char-major-4 INIT: version 2.78 booting Remounting root read-write... modprobe: modprobe: Can't locate module char-major-4 e-mgd board found - setting up ramdisk TC0521 12 Ed. 01 / 19-01-2004
REFORMATAGE ET RECHARGEMENT DE LA OmniPCX Enterprise Remount - Forces the media to be remounted Datalight FlashFx V4.05.309 Copyright (c) 1993-2000 Patent US#5860082 Disk Remounted e2fsck 1.19, 13-Jul-2000 for EXT2 FS 0.5b, 95/08/09 /dev/fla: clean, 48/7776 files, 6502/31062 blocks /dev/fla on /mnt/flash type ext2 (rw) INIT: Entering runlevel: 3 e-mgd version 16.7 Media Gateway Software R5.1 loading... No password file found - using default password list *** BIOS startup mode (2) forbidden when boot on flash filesystem *** *** Switch to dynamic mode (1) *** First time boot - disabling vlan tagging Internet Software Consortium DHCP Client 2.0pl5 Copyright 1995, 1996, 1997, 1998, 1999 The Internet Software Consortium. All rights reserved. Please contribute if you find this software useful. For info, please visit http://www.isc.org/dhcp-contrib.html Listening on Socket/eth0 Sending on Socket/eth0 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 4 DHCPOFFER from 10.24.1.20 DHCPREQUEST on eth0 to 255.255.255.255 port 67 DHCPACK from 10.24.1.20 No option router given! DHCP server: 10.24.1.20 Obtained IP address: 10.24.1.21 Netmask: 255.255.0.0 Gateway: Tftp server: 10.24.1.20 Lease time: 1800 bound to 10.24.1.21 -- renewal in 900 seconds. Duplex mode : auto-negociation BIOS updater is now working... getting current version information Check if we need to update with bios 3EH30227DQAA bios100/008.016... Reboot after bios update is enabled... ----- RetrieveFlashNorInfo ----- NOR VERSION : Bios Version in soldered NOR flash : 3EH30227DQAA bios100/008.016 len = 28 - Flash Nor Informations - Flash AMD Size : 512 Kbytes Number of sectors : 11 ----- CompareBiosVersions ----- CURRENT=008.016 FILE=008.016 ******************************* * NO bios Update is necessary * ******************************* Basic registers of MII PHY #1: 3100 786d 2000 5c21 05e1 45e1 0005 2801. Link status: active. loading modules - please wait... Real-Time Linux Dynamic Memory Manager 4.00 RTLinux System Call loaded Starting USER_PROCCES using fifo 7 6 Waiting for User Process registration Starting VG_PROCCES using fifo 5 4 Waiting for Vg Process registration Starting monitor using fifos 1/2 Alcatel kernel module loading...(break=0) Application User Process registered Application VG Process registered Main task created thread_id=0xc5252e00 stack address=0xc524cd58 stack bottom address = 0xc5248000 watchdogd now in real time mode DSP Manager OK Fast Socket Initialization... Ok ============ continue_rack_init ============== DIL SWITCH VALUE = 0x2 1024 Ko - BUFFER ALLOCATED MGD - RACK CONSTRUCTION @ MAC : 00:80:9f:2f:ef:37 Ed. 01 / 19-01-2004 13 TC0521
OmniPCX Enterprise REFORMATAGE ET RECHARGEMENT DE LA @ IP : 10.24.1.21 net mask : 255.255.0.0 gateway : 0.0.0.0 tftp server : 10.24.1.20 call server : 10.24.1.20 default crystal number : 3 (Dynamic allocation) vlan id : -1 default priority : 0 default dscp : 0 duplex mode : auto-negociation Module MG Loaded watchdogd now in normal mode RTLinux System Load 1.00 init_module GPA ->insmod GPA Module GPA loaded Module APA loaded Module SLAC loaded Module DDI loaded Module UAI loaded Module SLI loaded Insert INTX module Insert ISDN module Module BRA loaded Module PRA loaded Module PRACCS loaded Module PRA_T1CAS loaded Module PRA_E1CAS loaded ->init_module emga ==> emgd_emga & emgd_gpa module types created! Module emgd_emga loaded Module emgd_gpa loaded Module MIX loaded Module ATL loaded Module RESCUE loaded PUC_device registered Module DPNSS loaded Module DSPx_LOAD loaded Module UASIM loaded binmg : this is Media Gateway Software R5.1 for E-MGD version 16.7 built on 21 Aug 03 12 hours 02 min for r_mg_appli_16.7 Downloading /DHS3bin/downbin/emg/binmg from 10.24.1.20 No need to download a new version Checking other files Checking bindspbeconf version Downloading bindspbeconf Downloading /DHS3bin/downbin/emg/bindspbeconf from 10.24.1.20 bindspbeconf successfully downloaded watchdogd now in real time mode Copying bindspbeconf in flash Checking binmgcountry version Downloading binmgcountry Downloading /DHS3bin/downbin/emg/binmgcountry from 10.24.1.20 binmgcountry successfully downloaded Copying binmgcountry in flash ====== record_country_correspondaces ====== record_default_country 0 (DEFAULT COUNTRY : HU based with Poland tones) Downloading /DHS3bin/downbin/emg/binmcv_ver from 10.24.1.20 Downloading dsp binary Downloading /DHS3bin/downbin/emg/binmcv from 10.24.1.20 dsp binary successfully downloaded Copying binmcv in flash loading MCV module - please wait... DSP firmware successfully read in flash (size=657664) Startup completed - awaiting user login... Start VG_PROCESS using /dev/rtf5 Welcome to e-mgd IP is 10.24.1.21 *** Warning: connect to callserver failed! *** *** Please use resolve_connect to get possible cause of failure *** emgd login: TC0521 14 Ed. 01 / 19-01-2004
REFORMATAGE ET RECHARGEMENT DE LA OmniPCX Enterprise 3 A la fin du chargement des binaires e-mgd, le login e-mgd admin user est affiché sur le port de configuration V24. 4 Arrêter la carte GD/GA avec l'interrupteur On/Off et attendre que la LED power passe au rouge fixe. 5 Arrêter l'application OmniPCX Enterprise PC Installer sur le PC Serveur. 6 Dans le cas d'une carte GA, repositionner les dip switchs 1 et 2 sur ON, les dip switchs 3 et 4 sur OFF. Ed. 01 / 19-01-2004 15 TC0521
OmniPCX Enterprise REFORMATAGE ET RECHARGEMENT DE LA TC0521 16 Ed. 01 / 19-01-2004