Fixturing systems Fixturing systems for measurement technology Innovations and new additions to range
Sets Spannfix Eco complete set The set contains different supports, extension elements and stop units. Workpieces are clamped using spring clamps or toggleclamps. The base is formed by a base plate with mounting holes, which allows module elements to be fitted quickly and flexibly. Complete set "" contains a base plate with dimensions of 500 x 250 mm, while complete set "2" has a large base plate with dimensions of 00 x 00 mm. The complete set makes it possible to clamp an extremely wide variety of different sheet metal parts and plastic parts, including even milled and turned parts. Set versions Order number 2850 28570 Designation Spannfix Eco "" complete set Spannfix Eco "2" complete set Set contents Order number Designation Set "" Set "2" 9500 95040 284 28520 22005 2200 2000 8500 Base plate with tapped holes, 500 x 250 mm Base plate with tapped holes, 00 x 00 mm Base plate anchoring claws ( set) Quick-action clamp Screw frame sets with spring clamp Formed support with 90 point Self-aligning supports 25 mm columns, for spring clamp or as stop unit N2
Sets Spannfix Eco complete set (continued) Set contents Order number Designation Set "" Set "2" 8505 5800 02900 22200 2200 22400 04400 400 29500 2500 2400 0700 0800 275000 29700 4900 28580 50 mm columns, for spring clamp or as stop unit Retaining plates for columns 75 mm spring clamp 25 mm extension elements 5 mm extension elements 50 mm extension elements 00 mm extension elements Horizontal clamp with support dome Quick-change mounts 8 mm V-support, 20 40 mm V-support, 20 25 mm centre point, 90 40 mm centre point, 90 Thread adapter, M/M8 Articulated clamping arms, model SU 0-25 mm toggle-clamps V-support 20 with spring clamp 2 2 2 2 2 2 N
Sets Clamp set A New variant The "A" set with quick-action clamp, swivel unit and vice can be used for clamping milled and turned parts, for example. The swivel unit allows the vice and the workpiece to be tilted to the desired position. The clamping elements are mounted using the quick-action clamp, which is screwed directly either on the measuring table or on a base plate. The "A4" set additionally contains a three-jaw chuck, which can be used to ideally accommodate turned parts or workpieces with bores. The three-jaw chuck can equally be positioned in any angled position using the swivel unit. Ordering information When ordering, select the appropriate quick-action clamp or tell us at the time of order the size of the mounting hole or T-slot on your measuring table. Set A + Set A4 Set versions Order number 4050 40540 Designation Clamp set A Clamp set A4 Set contents Order number Designation Set A Set A4 08200 07800 200 28200 400 see right 80 mm precision vice Cylindrical pins for vice jaws with straight support surface (4 pcs) Cylindrical pins for vice jaws with inclined support surface (4 pcs) 0 mm precision three-jaw chuck Quick-action clamp swivel unit Quick-action clamp Order number Connection 28520 M 285208 M8 28520 M0 28522 M2 28500 T-slot N4
Clamping elements Horizontal clamp Horizontal clamp with M0 thread. Available in two size classes. Material Steel. Scope of delivery With lock nut. M0 Order number Overhang Clamp adjustment range M0 bolt adjustment range Height 288400 288500 8 2 0 50 0 8 0 4 0 5 0 5 70 85 Horizontal clamp with support Horizontal clamp with support and M0 thread. Available in two size classes. Material Steel. Scope of delivery With lock nut. M0 Order number Overhang Clamping range Height 00 400 2 5 0 20 0 27 00 5 N5
Sets Universal clamping set Clamping set for optical measuring instruments for quick and flexible clamping of round and cuboid workpieces, such as plastic, punched and turned parts. The clamping elements can be placed directly onto the measuring table or, if the quick-change adapter SWA9 is fitted, they can be positioned using the swivel unit. Set versions Order number 29855 29850 Designation "Universal" clamping set incl. case "Universal with swivel unit" clamping set incl. case N
Sets Universal clamping set (continued) Set contents Order number Designation "Universal" set "Universal with swivel unit" set 270920 5 mm precision vice 27080 5 mm precision vice 2825 50 mm precision vice 28200 Cylindrical pins with stepped profile, 4 pcs, for vice 27900 V-block with spring clamp 27050 Swivel unit with attachment plate and quick-action clamp 97020 Adapter plate SWA9 for 5 mm and 50 mm vices 400 Adapter plate SWA9 for 5 mm vice or V-block 29705 50 mm precision three-jaw chuck with quick-change adapter SWA9 The clamping elements contained in the set. The clamping elements can be placed directly onto the measuring table or they can be positioned at any angle using the swivel unit. N7
Sets Clamping component set New variant For optical measuring instruments and microscopes. For clamping plastic, punched or turned parts, for example. The base is a high-quality articulated clamping arm, on which clamping elements such as a mini chuck, spring clamp or toggle clamp can be mounted. The new clamping component sets contain a precision vice. Ordering information When ordering, please tell us the mounting thread or T-slot size of your measuring table. Set versions Order number 29805 2985 Designation "Standard model II" clamping component set with storage box "Small model II" clamping component set with storage box N8
Sets Clamping component set (continued) New variant Set contents Order number Designation "Standard model II" set "Small model II" set 29800 28900 Articulated clamping arm, model SU Try square with spring clamp Contains: Try square 20 x 80 mm, 2 columns for spring clamp (2800), left-hand spring clamp for horizontal clamping (29200), 5 mm spring clamp for vertical clamping (2900) 28200 2800 2800 27900 200 278800 2900 2900 29700 270900 000 Customer specification Right-hand spring clamp for horizontal clamping 50 mm spring clamp for vertical clamping Precision mini chuck V-block with spring clamp Small-parts clamp with stepped profile Toggle clamp Spring clamp with SWA5 Rotary unit Satellite mount, horizontal 5 mm precision vice Four-way hexagon socket spanner Adapter or T-slot block (see ordering information) N9
Clamping elements Spring clamp for horizontal clamping Spring clamp for clamping workpieces on toothed rails horizontally. Because of the curved design of the spring, small parts can be easily clamped into the corner of the angle. Clamping point length 2 mm to the slot centre. Material Brass/stainless steel. Mount- T L Order number Mount Clamping direction T L 4950 49250 5 5 Left Right 0. 0. 2 2 N0
Clamping elements Horizontal clamp for toothed rails Horizontal clamp for mounting on toothed rails. Material Steel/hard-coated aluminium. Spacers can be used to increase the clamping range (main catalogue, page 5) T-slot 5 Order number Overhang Clamping range Height 900 8 2 0 5 N
Base and structural elements Stop unit set The stop unit teeth are fastened to the toothed rails and can be positioned anywhere along the T-slot. Complex parts can be positioned securely and reproduceably with three points of contact. The stop unit teeth are available in lengths of 0 and 50 mm. Material Hard-coated aluminium/steel. Scope of delivery x stop unit teeth and x T-connector. Order number Designation Tooth length 47500 4750 0 mm stop unit set 50 mm stop unit set 0 mm 50 mm N2
Base and structural elements -point support set -point support for sheet metal parts, angled parts and formed parts. Flexible adjustment of the supports in x-, y- and z-direction. Simple and secure fixturing of the workpiece by spring clamp. The adjustable base rails can be flexibly fixtured along the T-slot on the toothed rails. The supports are height-adjustable. Extension elements can be used to compensate for further height differences. Material Hard-coated aluminium/steel. Scope of delivery x screw frame with spring clamp (2200), x 25 mm extension element (2250), x 50 mm extension element (22450), 2 x steel self-aligning support (2050), x column for 0 mm spring clamp (29042) Order number Designation 2995 -point support set N
Base and structural elements Accessories for -point support set Screw frame with spring clamp Adjustable base rail with height-adjustable support. With spring clamp for fixturing the workpiece. Order number Scope of delivery 2200 x base rail (22050), x 5 mm extension element (22250), x formed support (22750), x 0 mm retaining plate (5750), x column for 50 mm spring clamp (2904), x spring clamp (4700) Screw frame Adjustable base rail with height-adjustable support. Order number Scope of delivery 2200 x base rail (22050), x 5 mm extension element (22250), x formed support (22750) Supports Height-adjustable supports for supporting test parts. With M thread and an adjustment range of 5 mm. Order number Version Total length 22750 2050 200 2070 Formed support with mm dome radius Self-aligning support, steel, +/- 0 Self-aligning support, plastic, +/- 0 Magnetic support, dia. mm, 5 N 40 5 5 42 Extension elements Extension pieces with M male and female thread. Width across flats 7 mm. Order number Male thread Female thread Length 22250 2250 22450 M M M M M M 5 25 50 N4
T Base and structural elements Accessories for -point support set (continued) Base rail Adjustable base rail with slot and M mounting thread. Scope of delivery Incl. fastening screw and T-slot block Order number Adjustment range Total length 22050 50 8 Retaining plates Mounting plates for spring clamp columns with M4 or M thread. For mounting on extension pieces or directly on base rail. Order number Thread for columns Retaining bore Overhang 5750 5850 M4 M 0 50 Columns for spring clamps Columns for mounting spring clamps. Order number Column dia. Length Thread 29042 2904 29044 800 8200 800 4 4 4 0 50 75 0 50 75 M4 M4 M4 M M M Spring clamp Simple and quick clamping of workpieces. Spring clamp 470 with narrow spring design. Order number T L Mount Ø Ø Mount 2907 4700 470 02800 0.4 0.8 0.8.0 0 0 0 50 4 4 4 L Ausführung flach Gabel rund N5
Symbol legend Imprint M0 T-slot 5 Connection with an M0 metric thread. Connection via T-slot. Width 5/0 mm, height 2.5/2.5 mm. For use predominantly in the Schienenfix fixturing system. The symbols are intended to make it easier for you to combine the individual base, structural and clamping elements to form complete fixturing systems. For individual products, it is the connection concerned that is illustrated, while in the case of adapters, both interfaces are shown. Publisher dk Fixiersysteme GmbH & Co. KG Ferdinand-Lassalle-Straße 5 72770 Reutlingen, Germany www.dk-gmbh.de info@dk-gmbh.de Catalogue number Z20000 54-DE, issue Edition May 204 Note Dimensions and other data conform to the latest technical standards at the time of publication. We reserve the right to introduce technical modifications at any time. We can accept no responsibility for printing errors. Reprinting or duplication even in part is not permitted without our consent. dk Fixiersysteme GmbH & Co. KG Ferdinand-Lassalle-Straße 5 72770 Reutlingen, Germany Tel. +49 (0) 72 90 97 0 Fax +49 (0) 72 90 97 20 www.dk-gmbh.de info@dk-gmbh.de