RF Switching 5000 Series Matrix Member of FOSHAY Group of Companies Veteran Owned 1
Table of Contents Our Organization 2 16X16 Switching Matrix - 20 MHz - 3000 MHz 3 VHF / UHF RF Matrix - 20 MHz - 3000 MHz 4 8X16-Fan-Out 4 16X16-Fan-Out 4 L-Band RF Matrix - 950 MHz - 2150 MHz 5 16X16 - Fan-Out 5 16X32 - Fan-Out 5 32X16 - Fan-Out 5 32X32 - Fan-Out 5 16X16 - Fan-Out 5 16X32 - Fan-Out 5 32X4 - Fan-Out 5 32X32 - Fan-Out 5 L-Band RF Matrix - 950 MHz - 2150 MHz 6 32X8 - Fan-In 6 32X16 - Fan-In 6 32X8 - Fan-In 6 32X16 - Fan-In 6 2 V2-0212
Our Organization ICOMPANY PROFILE CrossPoint s switching product designs have earned worldwide recognition for quality and reliability. In conjunction with its sister division, IF Engineering Corp., which produces all internal components of CPT s RF Matrix, we are able to provide some of the most advanced and custom tailored solutions that meet or exceed specific needs of each of our global customers. Our Systems cover from DC to 18 GHz, with special emphasis on the HF, VHF, UHF and L-Band applications. CrossPoint has always emphasized advanced research and development, the highest engineering skills, modern manufacturing tools and techniques, stringent quality assurance procedures and adherence to customer schedules. CrossPoint is ISO 9001:2008 certified and committed to continuous product improvement OUR HERITAGE (CPT) was founded in 2002. CPT provides a manufacture of value-added solutions and RF Switching Systems concentrating on optimization and conditioning of the signal. This optimization is achieved by incorporation of passive and active components into one sub-system solution. standard features such as: A broad line of products with optimized layouts Custom configured hardware and software options Remote control interface options Use of premium performance components Assemblies built using rugged, rack mount, chassis CPT Matrices are performing reliably in a variety of environments including tracking radars, anti-jam, signal exploitation, ELINT, CO- MINT, radar simulation, wireless communication, and earth stations with over 450,000 hours of uninterrupted service. Critical System Components Made In-House Power Dividers (Splitters) and Combiners, Resistive DC to 6 GHz in a single unit, 2 port to 32 port devices. Power Dividers (Splitters) and Combiners, Lumped Constant / C Band Power Combiners Switching Products Broadband units that operate from 20 MHz to 3000 MHz, available in 2 way, 4 way, 8 way and 16 way. Offering includes complete line of C-Band (up to 7 GHz) Power Dividers and Combiners for Down /Uplink facilities and Matrix Switch applications. All product is offered in connectorized as well as Surface Mountable versions. Several types of switch products covering the 0.1 MHz to 2.5 GHz. Our designs incorporate P.I.N. diodes, Electro Mechanical, and GaAs devices. The designs include 1 x 2 through 1 x 16, and transfer switching. Directional Couplers Signal Control and Conversion From three port, four port, and dual Directional Couplers with typical coupling tolerances of <0.5dB, directivity >20dB, with VSWR <1.2:1. Standard coupling values are 6, 10, 14, 15, 16, 20, and 30dB. The couplers are available in several connectorized packages as well as surface mountable, and operate from 0.1 MHz to 3 GHz. Providing comprehensive line of Up/Down Converters with internal phase locked L.O., Digital Attenuators, Digital Phase Shifters, Vector Modulators, Single Side-Band Modulators, Image Reject Mixers, and I&Q Demodulators/Phase Comparators, Amplifiers and Switching Boards 2
16X16 Switching Matrix - 20 MHz - 3000 MHz CPT-076-1221 The Switching Matrix The CPT-076-1221 was developed specifically for extended broadband frequencies, broadband frequency of 20 MHz up to 3000 MHz. The 16X16 matrix is able to cover all critical bands such as VHF, UHF, Extended VHF / UHF and L-Band for many applications. The CPT-076-1221 lies in the heart of all 5000 Series RF Matrices by providing improved and unparallel ultra low insertion loss, making it ideal for usage as itself of a part of communication switching suite. The CPT-076-1221 is a Non-Blocking Full Fan-Out Switching Matrix designed and manufactured as a single functional block. The system connects any input to any one or multiple outputs simultaneously, starting with a switching matrix of 16X16 in a low 1RU profile. The 16x16 module can also be stacked to realize a 16x32, 32x16 or 32x32 matrix. The 16x32 and 32x16 would fit into a 2U chassis and the 32x23 would fit into a 3U chassis. This concept provides the advantage of a very compact and cost efficient design with excellent modularity and mean time to repair. Technical Features The enhanced isolation of this matrix, brings many benefits to critical applications. The matrix can be used byitself or be a part of a larger system. The matrix provides >65dB of isolation across the entire bandwidth and better than 70dB below 1.5GHz. As an example, in Satcom applications, that receive very low power signals from remote space craft, high isolation is required between channels. CPT could provide this with and without amplifiers and optimize the final configuration for the required bandwidth of interest. RF Specification CPT-076-1221 Frequency Range (MHz) 20-3000 Number of Input Ports 16 Number of Output Ports 16 Insertion Loss (db) Max VSWR (Max) 20-1000 MHz 21 1000-2000 MHz 24 2000-3000 MHz 28 In 1.75:1 Out 1.75:1 Isolation (db) Min 65 RF Connectors - In / Out DC Voltage Size SMB (J) 5 VDC @ 1A 1.160 H x 12.488 W x 12.688 D Environmental Storage Temp: Operating Temp: Operating humidity: -20 to +70 C 0 to +60 C 10 80% (non condensing) 3
VHF / UHF RF Matrix - 20 MHz - 3000 MHz MS-5000-8X16-VHF-UHF-FO MS-5000-16X16-VHF-UHF-FO 5000 Series Matrix The 5000 UHF / VHF Model of Solid State RF Switching System is a Non-Blocking Full Fan-Out Switching Matrix. Housed in a low 1 RU profile, the system connects any input to any one or multiple outputs simultaneously. The broadband operation covers the entire 20MHz to 3GHz frequency range using a low profile architecture that provides a 16x16 in a 1RU chassis and a 32x32 matrix in a 3RU chassis. The system incorporates a 16x16 building block that delivers market-leading RF performance and best in class isolation. Typical worse case isolation/crosstalk is >70dB up to 1GHz and >65dB at 3GHz. Using a modular, multi-chassis approach, 16x256 or 256x16 switch sizes can be configured. Both fan-out and fan-in systems are standard. Shown MS-500-16X16-VHF-UHF-FO System includes (as an option) dual redundant AC Power Supply along with Hot Swapable Amplifiers and RF Switch Modules. Control of the system includes standard features such as a manual control by the way of front key pad and LCD display, along with series of remote controls such as RS-232, RS -422 and 10Base-T / Ethernet connectivity. All systems include 2 years of warranty coverage. RF Specification Features Solid-State Switching Built In diagnostics and Fault Indicators Standard Modular Design Benefits No mechanical lifetime limits Small Size Low Power Remote failure notification Fast troubleshooting and LRU identification Proven performance and reliability System commonality to reduce required spares Reduced MTTR Frequency Range (MHz) 20-3000 Number of Input Ports 8 or 16 Number of Output Ports 16 Gain 20-1000 MHz 0 ±2.0 Gain 1000-2000 MHz -1.5 ±2.5 Gain 2000-3000 MHz -1 ±3.0 Noise Figure (db) 8 Isolation (db) In / In (Min) 20-1500 MHz >80 1500-3000 MHz >60 Isolation (db) Out / Out (Min) 20-3000 MHz >80 Isolation (db) In / Out (Adj) 20-1500 MHz >70 1500-3000 MHz >65 Rev Isolatiion (db) Out / In 20-1500 MHz >75 1500-3000 MHz >65 Environmental 80 264 VAC, 47 63 Hz, 3-6 A, 250 W (max) Standard AC grounded power cable (removable, IEC 320 C19 to NEMA 5 15P) Fuse/Breaker: Externally accessible/replaceable Storage Temp: -20 to +70 C Operating Temp: 0 to +60 C Operating humidity: 10 80% (non condensing) Frequency Range (MHz) 20-3000 1 db Compression Point (db) Min 20 +1 1500-2 3000-9 OPIP3 (dbm) +24 OPIP2 (dbm) +12 VSWR (Max) In 2.0:1 Out 1.7:1 Impedance (ohm) 50 RF Connectors - In / Out AC Voltage / Power Consumption Size Weight SMA / SMA 90-240VAC, 47-63Hz, 25W 1.75 H x 19 W x 14.5 D 20 Lbs Command and Control Local control via front panel Solid state controller with LCD display Remote control via network connection: >> Rear panel RS-232 and RS-422 (DB25 female) standard DCE pin out >> Baud Rate 9600 >> 10BT/100/100BT Ethernet interface (RJ-45 connector) 4
L-Band RF Matrix - 950 MHz - 2150 MHz MS-5000-16X16-LB-FO MS-5000-16X32-LB-FO MS-5000-32X16-LB-FO MS-5000-32X32-LB-FO 5000 Series Matrix The 5000 Model of Solid State RF Switching System is a Non-Blocking Full Fan-Out Switching Matrix. The system connects any input to any one or multiple outputs simultaneously, starting with a switching matrix of 16X16 with possible expansion up to 32X32 matrix. The core of the system utilizes a specially designed 16X16 switching matrix in a single module. These systems are outfitted with high linearity amplifiers on all inputs in order to compensate for a total insertion loss of the system. System includes (as an option) dual redundant AC Power Supply along with Hot Swapable Amplifiers. Control of the system includes standard features such as a manual control by the way of front key pad and LCD display, along with series of remote controls such as RS-232, RS -422 and 10Base-T / Ethernet connectivity. All systems include 2 years of warranty coverage. RF Specification Features Solid-State Switching Built In diagnostics and Fault Indicators Standard Modular Design Benefits No mechanical lifetime limits Small Size Low Power Remote failure notification Fast troubleshooting and LRU identification Proven performance and reliability System commonality to reduce required spares Reduced MTTR MS-5000-16X16-LB-FO MS-5000-16X32-LB-FO MS-5000-32X4-LB-FO MS-5000-32X32-LB-FO Frequency Range (MHz) 950-2150 Number of Input Ports 16 16 32 32 Number of Output Ports 16 32 16 32 Min Typ Max Min Typ Max Min Typ Max Min Typ Max Gain -2.0 0.0 +2.0-2.0 0.0 +2.0-2.0 0.0 +2.0-3.0 0.0 +3 Isolation (min) 65 70 65 70 65 70 65 70 VSWR 1.8:1 2.0:1 1.8:1 2.0:1 1.8:1 2.0:1 1.8:1 2.0:1 1 db Compression Point -5 0-8 +3-8 +3-10 -5 Noise Figure 8 10 8 10 8 10 8 10 OPIP3 +8 + 10 +5 +7 +5 + 7 +3 +5 OPIP2 +18 +20 +15 +17 +15 +17 +13 +15 Impedance (ohm) 50 RF Connectors - In / Out SMA / SMA AC Voltage / Power Consumption 80-264VAC, 47-63Hz, 50W 80-264VAC, 47-63Hz,75W 80-264VAC, 47-63Hz,75W 80-264VAC, 47-63Hz,125W Size 1.75 H x 19 W x 14.5 D 5.25 H x 19 W x 14.5 D Environmental 80 264 VAC, 47 63 Hz, 3-6 A, 250 W (max) Standard AC grounded power cable (removable, IEC 320 C19 to NEMA 5 15P) Fuse/Breaker: Externally accessible/replaceable Storage Temp: -20 to +70 C Operating Temp: 0 to +60 C Operating humidity: 10 80% (non condensing) Command and Control Local control via front panel Solid state controller with LCD display Remote control via network connection: >> Rear panel RS-232 and RS-422 (DB25 female) standard DCE pin out >> Baud Rate 9600 >> 10BT/100/100BT Ethernet interface (RJ-45 connector) 5
L-Band RF Matrix - 950 MHz - 2150 MHz MS-5000-32X8-LB-FI MS-5000-32X16-LB-FI 5000 Series Matrix The 5000 Model of Solid State RF Switching System is a Non-Blocking Full Fan-In Switching Matrix. The system connects any input to any one or multiple outputs simultaneously, starting with a switching array of 16X8 with possible expansion up to 32X32 RF Matrix. The core of the system utilizes a specially designed 16X16 switching matrix in a single module. These systems are outfitted with high linearity amplifiers on all inputs in order to compensate for a total insertion loss of the system. System includes (as an option) dual redundant AC Power Supply along with Hot Swapable Amplifiers and RF Switch Modules. Control of the system includes standard features such as a manual control by the way of front key pad and LCD display, along with series of remote controls such as RS-232, RS -422 and 10Base-T / Ethernet connectivity. All systems include 2 years of warranty coverage. RF Specification Features Solid-State Switching Built In diagnostics and Fault Indicators Standard Modular Design Benefits No mechanical lifetime limits Small Size Low Power Remote failure notification Fast troubleshooting and LRU identification Proven performance and reliability System commonality to reduce required spares Reduced MTTR MS-5000-32X8-LB-FI MS-5000-32X16-LB-FI Frequency Range (MHz) 950-2150 Number of Input Ports 16 16 Number of Output Ports 16 32 Min Typ Max Min Typ Max Gain -2.0 0.0 +2.0-2.0 0.0 +2.0 Isolation (min) 65 70 65 70 VSWR 1.8:1 2.0:1 1.8:1 2.0:1 1 db Compression Point 0 +5 0 +5 Noise Figure 15 20 15 20 OPIP3 +10 + 15 +10 +15 OPIP2 +20 +25 +20 +25 Impedance (ohm) 50 RF Connectors - In / Out SMA / SMA AC Voltage / Power Consumption 80-264VAC, 47-63Hz, 75W 80-264VAC, 47-63Hz,100W Size 3.5 H x 19 W x 14.5 D 5.25 H x 19 W x 14.5 D Environmental 80 264 VAC, 47 63 Hz, 3-6 A, 250 W (max) Standard AC grounded power cable (removable, IEC 320 C19 to NEMA 5 15P) Fuse/Breaker: Externally accessible/replaceable Storage Temp: -20 to +70 C Operating Temp: 0 to +60 C Operating humidity: 10 80% (non condensing) Command and Control Local control via front panel Solid state controller with LCD display Remote control via network connection: >> Rear panel RS-232 and RS-422 (DB25 female) standard DCE pin out >> Baud Rate 9600 >> 10BT/100/100BT Ethernet interface (RJ-45 connector) 6
Corporate Headquarters Phone: +1-860-935-0280 Fax: +1-860-935-0283 West Coast / International Sales Office 7146 University Drive Moorpark, CA 93021, USA Phone: +1-774-329-5970 Fax: +1-860-935-0283 www.crosspointtechnologies.com ISO Certified 9001:2008 Member of FOSHAY Group of Companies Veteran Owned 7