GSM Voice Auto Dialer & SMS Sender JC-999

Transcription

1 GSM Voice Auto Dialer & SMS Sender JC-999 Main features: () Large LCD display,integrated integrated keypad, human-friendly programming; (2) Support 2 alarm receiving numbers; (3) Triggering means: N.C N.O and voltage trigger optional; (4) Trigger time: 0.5s and 30s optional; (5) Support to stop all alarm call on mobile phone, to avoid trouble by fault alarm; (6) 20s changeable voice message, (7) Short message can be updated (8) Phone call, SMS arm/disarm, and arm/disarm on keypad; (9) Programmable zone characteristics(24h zone or arm/disarmed zone) (0) Support reset the password by RESET key. () Arm/disarm password and programming password can be set independently. (2) High capability battery, standby time more than 48h

2 Wiring diagram DC is for power input Jumpers A and B are for choosing zone triggering type. Wiring terminal marked with +- is for trigger signal input. Standard packing: Auto dialer Power adaptor User s Manual 2

3 GSM Wireless Terminal/ communicator JC-00 Main Description: The JC 00 GSM Terminal is a wireless communicator for alarm and fire panels that uses the cell phone network (GSM) to transmit alarms and other panel event. The module checks the status of the PSTN line and in case the PSTN line becomes unavailable, the JC 00 GSM emulate the line signal to the panel. At this time, the panel will dial out using the GSM cell phone network to communicate with the receiver at the monitoring station and transmit the alarms. Main features: GSM network, can be used wherever there is cell phone coverage Panel compatibility - Allows any Contact ID alarm panel to transmit alarms using the GSM voice channel RJ port, telephone line backup: Uses the telephone line as the main transmission line and uses the GSM voice channel as backup Auto restart system: It can continuously monitor the system status. Programmable Account Number: Send additional systems state (with user programmable Account number) to the monitoring station. Supported Protocol: Pager message (DTMF with handshake) 3

4 Sends text messages to programmable cell phone number (SMS) to notify the user that the PSTN line has been cut off or unavailable. Arm/disarm the unit remotely via remote control, SMS or phone call, it also can connect to the basic telephone to perform arm/disarm. Three digital inputs zones: Trigger when short circuit, and each zone input can choose to make alarm call or not, alarm by SMS or not. Support 8 phone numbers. Three remote control outputs: (Sink max 300mA per output) can switch on lighting, air conditional, generator, sensor or other equipment remotely through a SMS or phone call. Specifications: *Rechargeable battery to prevent power failure or electricity cut off by intruder. The GSM will function as normal when no electricity supply. *Low power consumption - uses 30mA while in idle state and 260mA when transmitting an alarm *Working frequency: GSM900MHz/GSM800MHz *Stability of frequency: better than 2.5PPM *Signal sensitivity: -03dBM * Transmit power: <2w *Power: 220v±5% AC *Input Voltage Tolerances: ~20VDC *The max distance between terminal and telephone: 00M *Environment temperature: 0~+50 *Relative humidity: 0%~95% *Air pressure: 86~06kpa External wiring diagram 4

5 Standard packing: Auto dialer Telephone line DB5 (F) cable Power adapter 5m GSM terminal antenna User s Manual GSM Terminal/ communicator JC-0 5

6 Main features: Supports both GSM networks and phone. It can work with alarm systems and phones. LCD display, fashion design 0 alarm receiving numbers programmable by computer software. Incoming numbers and dialing numbers block enable Support Caller ID and Hands free, Caller ID display Compatible to PABX. Time, date, signal intensity display enable LED Indicators for signal and power status Allow PIN code entering and reciprocal phone-card lock Polarity reversal signal for metering Simple to install and easy to maintain Cost rate setting enable Backup battery RJ port Specifications: *4-Band GSM: MHz, 900MHz, universal. *Module Type: Industrial module item *3.5dBi gain antenna *Power supply: DC5V *Sensitivity: -04dB *Stand by hours: 48 Hours *Talk time: 2-6 Hours *Charging time: 6 hours *Peak power consumption: 2W *Connectors: SMA antenna connector (TNC optional) *Power consumption: Static: 25mA, emission: 500mA *Operation Temperature: *Atmospheric pressure: 86~06Pka Standard packing: Auto dialer Antenna Power adaptor User s Manual 6

7 JC TECHNOLOGY GROUP CO., LIMITED ADD: Qianshi Mansion, Oubei Town,Yongjia, Wenzhou, Zhejiang, China Zip: Tel: , Fax: Skype: jctechsales, tracyheechina MSN: Web: 7