Motor. Operations. Handbook

Motor Operations Handbook 212 Version 5.

MISSION Cougar Drilling Solutions strives to be the premier supplier of Vertical, Directional and Horizontal Drilling Services to the oil, gas and geothermal exploration and development industry. Cougar Drilling Solutions strives to set the standard by which all others are judged. 212 Version 5. The information in this handbook is subject to change without notice. If you have any questions or concerns, feel free to contact any of our locations.

Cougar DS Motor Operations INTRODUCTION CONTENTS COMPONENTS BEARING ASSEMBLY... 3 FIXED HOUSING... 4 ADJUSTABLE ASSEMBLY... 4 DRIVE SHAFT ASSEMBLY... 4 POWER SECTION... 5 ROTOR CATCH... 6 DUMP SUB... 7 TOP SUB... 7 STABILIZATION... 8 APPLICATIONS MOTOR SELECTION... 9 DRILLING... 9 PERFORMANCE DRILLING... 1 DIRECTIONAL DRILLING... 11 HORIZONTAL DRILLING... 11 AIR DRILLING... 12 H 2 S... 15 OPERATIONS SURFACE TESTING... 16 RUNNING IN... 16 REACTIVE TORQUE... 17 MOTOR STALL... 18 ROTATING THE MOTOR... 19 ROTOR BYPASS... 2 MOTOR PRESSURE DROP... 2 BIT PRESSURE DROP... 21 PLUGGING OFF... 21 PULLING OUT... 22 I

Cougar DS Motor Operations CONTENTS (cont d) FLUIDS DRILLING FLUIDS... 23 TEMPERATURE DOWNHOLE TEMPERATURE... 25 TROUBLE SHOOTING DECREASE IN ROP... 26 SUDDEN PRESSURE INCREASE... 26 LOW PRESSURE... 27 ADJUSTABLE INSTRUCTIONS ADJUSTABLE INSTRUCTIONS... 28 TORQUE SPECIFICATIONS... 31 RESETTING INSTRUCTIONS... 31 MUD MOTORS PERFORMANCE SPECIFICATIONS MOTOR CHART EXAMPLE... 34 MOTOR OPERATIONS... 35 MOTOR FISHING DIMENSIONS... 37 STABILIZER FISHING DIMENSIONS... 39 II

Cougar DS Motor Operations CONTENTS (cont d) DRILLING MOTOR SPECIFICATIONS 3-1/8 7-8 Lobe 7-8 Lobe 3. 4. Stage... 42 Stage... 44 3-3/4 4-5 Lobe 7-8 Lobe 7-8 Lobe 3.5 2. 2.3 Stage... 48 Stage... 5 Stage... 52 4-3/4 4-5 Lobe 7-8 Lobe 7-8 Lobe 3.5 2. 2.2 Stage... 56 Stage... 58 Stage... 6 7-8 Lobe 2.6 ESX Stage... 62 7-8 Lobe 7-8 Lobe 3.8 4.5 SX Stage... 64 Stage... 66 7-8 Lobe 4.5 SXHR Stage... 68 5 6-7 Lobe 6. Stage... 72 6-7 Lobe 7. Stage... 74 6-1/4 7-8 Lobe 4.8 Stage... 78 6-1/2 4-5 Lobe 4.8 Stage... 82 6-7 Lobe 3.1 ERT Stage... 84 6-7 Lobe 5. Stage... 86 6-7 Lobe 5. HR Stage... 88 7-8 Lobe 2.9 Slow Stage... 9 7-8 Lobe 3. Stage... 92 7-8 Lobe 3. Slow Stage... 94 7-8 Lobe 5. Stage... 96 7-8 Lobe 5. HR Stage... 98 7-8 Lobe 5.7 Stage... 1 7-8 Lobe 5.7 HR Stage... 12 8-9 Lobe 3. Stage... 14 III

Cougar DS Motor Operations CONTENTS (cont d) DRILLING MOTOR SPECIFICATIONS (cont d) 6-3/4 6-7 Lobe 3.1 ERT Stage... 18 6-7 Lobe 5. Stage... 11 6-7 Lobe 5. HR Stage... 112 7-8 Lobe 2.9 Slow Stage... 114 7-8 Lobe 3. Stage... 116 7-8 Lobe 5. Stage... 118 7-8 Lobe 5. HR Stage... 12 7-8 Lobe 5.7 Stage... 122 7-8 Lobe 5.7 HR Stage... 124 8 4-5 Lobe 3.6 Stage... 128 7-8 Lobe 2. Stage... 13 7-8 Lobe 3.4 ESX3 Stage... 132 7-8 Lobe 4. Stage... 134 7-8 Lobe 4. HR Stage... 136 9-5/8 3-4 Lobe 4.5 Stage... 14 3-4 Lobe 6. Stage... 142 5-6 Lobe 3. Stage... 144 5-6 Lobe 5. Stage... 146 5-6 Lobe 5. HR Stage... 148 6-7 Lobe 5. Stage... 15 11-3/4 3-4 Lobe 3.6 Stage... 154 5-6 Lobe 4.6 Stage... 155 IV

Cougar DS Motor Operations TABLES AND CHARTS CONTENTS (cont d) Heavy Weight Drill Pipe... 158 Collar Weights... 159 Drill Bit Sizes... 163 Buoyancy Factors... 164 Hole Curvature... 165 Coon Inch Measurements... 166 Conversion Factors... 167 Nozzle Sizing Chart... 171 V

Cougar DS Motor Operations Introduction Cougar Drilling Solutions Inc. is pleased to present the latest release of the mud motor operations handbook. This release features more motor sizes and configurations, motor operation information and a thorough compilation of useful tables and charts. We hope that this handbook will be a helpful tool when using the Cougar Drilling Solutions motors. If you require further information please contact us at (78) 44 24 or by e-mail at info@cougards.com or consult www.cougards.com. The contents of this handbook are for information and reference only. Cougar Drilling Solutions has made every effort to ensure the validity and accuracy of the information contained within, however, Cougar Drilling Solutions does not warrant nor guarantee the contents. The user assumes the responsibility and liability for the use of the information contained within. The contents of this handbook are subject to change without notice. Copyright 28 Cougar Drilling Solutions Inc. All Rights Reserved.

Cougar DS Motor Operations

Cougar DS Motor Operations BEARING ASSEMBLY The Bearing Assembly carries all radial and thrust loading. Cougar Drilling Solutions utilizes a special rotary shaft seal designed specifically for drilling motor use that is isolated from drilling fluid at all times. The Bearing Assemblies are designed to reduce the bearing load with more radial support for side loading and with high capacity thrust bearings for on or off bottom loading. Cougar Drilling Solutions motors are built to handle all drilling conditions from corrosive muds to high temperature holes up to 25 F for the standard configuration. If required, the motor can be outfitted with a power section and bearing assembly seals to accoodate higher operation temperatures. Cougar Drilling Solutions Bearing Assembly is a completely oil sealed unit. The sealing system used includes a unique flow restrictor design, which delivers maximum flow to the bit. All drilling fluid is directed to the bit rather than being used to lubricate the bearings. The result is exceptional hydraulic horsepower and hole cleaning along with increased bit life and penetration rates. The Cougar Drilling Solutions Bearing Assembly has a large bit mandrel to provide an accurate and durable drive system. It was designed with a large bore, which has been maintained throughout the motor, to minimize the pressure drop across the motor and maximize hydraulic power. 3

Cougar DS Motor Operations FIXED HOUSING Where there is no need for field adjustment, Cougar Drilling Solutions can supply Fixed Housings to take place of the Adjustable Assembly. Fixed Housings are available in straight or bent orientations up to 3 degrees. ADJUSTABLE ASSEMBLY The Adjustable Assembly connects the stator to the housings of the Bearing Assembly and houses the Drive Shaft Assembly. The Adjustable Assembly is easily set in the field from straight to 3 degrees of bend angle. The Cougar Drilling Solutions Adjustable Assembly has 15 settings allowing fine adjustment for refinement in build rates. The design of the Cougar Drilling Solutions Adjustable allows for greater build rates due to its short bit to bend length. DRIVE SHAFT ASSEMBLY The Drive Shaft Assembly connects the Power Section s rotor to the rotating components of the Bearing Assembly. The Drive Shaft converts the eccentric motion of the rotor into concentric rotation. The Drive Shaft also compensates for any angle of the Adjustable Assembly or Fixed Housing as well as the bending subjected to the motor during directional control. Cougar Drilling Solutions Drive Shaft Assembly uses robust, sealed and lubricated joints at both ends, mated by a massive connecting shaft. The resulting assembly can handle torques in excess of the stall torque of the Power Sections used while carrying the thrust load imposed by the pressure drop across the Power Section. 4

Cougar DS Motor Operations POWER SECTION The Power Section converts hydraulic power into rotary motion. Drilling fluid pumped through the drill string drives what is essentially a reversed positive displacement pump connected to the bit. The Power Section is composed of a rotor and stator. The rotor, the driven member, is a helical shaped steel bar that is forced to turn inside the elastomer lined stator tube. The lining of the steel stator tube is molded in a similar helical pattern, but with longer pitch lengths, to form sealed cavities as the rotor turns. Drilling fluid pumped through the stator creates a pressure drop across the cavities, causing the rotor to turn. The number of lobes along with the length of the helix determines the performance of a Power Section. The stator profile has one more lobe than the rotor. This relationship is part of the name defining a given Power Section, ex. 7-8 Lobe. As the lobe count increases the final drive speed generally decreases. The second feature used to define a Power Section is the number of stages. One stage is one complete helical rotation, or pitch, of the stator. As the number of stages increases, the differential pressure and the torque also increase. When circulation rates are required that are higher than that recoended for the Power Section used, the rotors can be jetted to allow excess fluid to by-pass the stator, preventing damage to the elastomer liner. Variations in fits and materials are available for Cougar Drilling Solutions power sections for operating under extreme temperatures or with specialized drilling fluids. 5

Cougar DS Motor Operations ROTOR CATCH The Rotor Catch is a tool used in down-hole Drilling Motors to assure the extraction of the Rotor. On rare occasions, motors, mainly the power section, have parted below the Stator. When this occurs generally the stator comes out of the hole leaving the Rotor facing up hole and resulting in a fishing job over an uneven surface. Also, if the bit is not stuck it is hard to rotate over the Rotor to fish it, as there will be no resistance to it also turning. The Rotor catch sits at the top of the Power Section and screws directly into the Rotor. If the tool should part, the Rotor Catch will contact an internal shoulder and retrieve the Rotor. 6

Cougar DS Motor Operations DUMP SUB The Dump Sub is a by-pass valve used above the motor, which allows drilling fluid to fill the bore of the drill string when tripping into the hole, and drain when tripping out of the hole, preventing a wet trip. When there is little or no circulation, a piston in the valve is held in an open position by a coiled spring; drilling fluid flows directly to the annulus. As circulation begins to increase, the force of the fluid causes the piston to compress the spring and seal off the ports to the annulus. With the ports sealed, all drilling fluid is pumped through the power section to turn the bit. On most motor sizes, the Dump Sub can be disabled by substituting solid plugs for the ported ones threaded into the body. Cougar Drilling Solutions Dump Subs are designed to close before the minimum recoended circulation rate of a given motor configuration is reached. The Dump Sub creates negligible pressure loss while drilling. TOP SUB The Top Sub is basically a Cross Over Sub, to adapt the downhole motor assembly. All Cougar Top Subs c/w a Float bore. 7

Cougar DS Motor Operations STABILIZATION Cougar Drilling Solutions Bearing Assemblies come with threaded O.D. bearing housings to accoodate either a smooth thread protector or a thread on stabilizer. The stabilizers are easily changed on the rig floor and provide added support for packed or pendulum drilling assemblies. If no stabilization is required, the bearing housing is available in a non-threaded version for slick assemblies. 8

Cougar DS Motor Operations MOTOR SELECTION Cougar Drilling Solutions offers a wide range of power sections to accoodate almost any type of drilling and drilling conditions. The motors can be specified to match the torque requirements of the bit, the flow rates for cleaning, the maximum standpipe or pump pressure or even materials for high temperature applications. Should higher flow rates than the power sections available be required, all of Cougar Drilling Solutions motors can be configured with a bypass jet. This enables the flow rates to be considerably increased without causing the power section to be over-pumped and run inefficiently. DRILLING In order to drill using a motor, the standpipe pressure must be monitored. Initially, rotation must be started in the offbottom position. The performance charts in this booklet will give the required pressure to initiate the rotation for a given motor size. Note that more pressure may be required than indicated on these charts to initiate rotation. Regions such as keyseats may cause difficulties if the motor is not oriented properly or set to a high build angle. The off-bottom pressure, as measured on the standpipe gauge, will include the pressure differential across the motor as well as any other losses due to other tools and friction. Once the motor is rotating it may then engage the well bottom. Contacting the bottom will be directly visible on the pressure indicator, as the pressure on-bottom will increase from the pressure off-bottom. 9

Cougar DS Motor Operations Caution must be taken not to allow the differential pressure to exceed the maximum differential pressure for a given motor size. The weight on bit may be increased until the desired rate of penetration (ROP), torque or maximum differential pressure is reached. As drilling coences, the weight will drill off thus lowering the torque and consequently the pressure on the indicators. It is important to re-check the off-bottom pressure periodically to ensure the motor is running optimally. As the amount of cuttings increase in the drilling fluid, some hydraulic power will go to lifting these cuttings so the pressure may need to be adjusted. If the drilling conditions are favourable, rotation of the motor when the adjustable housing / fixed housing is set from 1.5 degrees or less is possible. This would enable the driller to steer and/or create a better environment for weight transfer to the motor. Care should be taken to not rotate the motor when it is set above 1.5 degrees or at string rotational speeds greater than 5 RPM. PERFORMANCE DRILLING Cougar Drilling Solutions motors are capable of meeting the high torque or high RPMs of today s performance drilling requirements. Many modern bits such as PDCs require more torque. The high performance power sections can deliver the necessary torque; drillers will experience increased ROP and less string wear. 1

Cougar DS Motor Operations DIRECTIONAL DRILLING The Cougar Drilling Solutions motor facilitates directional drilling with the use of the adjustable or fixed housings. By setting a bend between the drive and bearing assemblies, the lower portion of the motor and the bit face are oriented such as to initiate a build in the well bore. When the drill string is not rotating, the motor will build, however, when the string is rotating, the motor will drill effectively straight. The motor may be oriented to enable drilling up or down in a build. Directional drilling has application in many fields from utility, river crossing and avoiding problematic formations and many more. Multi-laterals have become an important addition to the many uses of a steerable assembly. This enables the creation of multiple lateral wells off of one main vertical well, greatly reducing the cost of producing a large zone. HORIZONTAL DRILLING The idea of directional drilling can be extended to horizontal applications. The key difference in this application is that the bend angle in the adjustable may require being set higher to create tight build rates. This eliminates the idea of rotating the assembly for steering. When the tool is set over 1.5 degrees, the motor should not be rotated. 11

Cougar DS Motor Operations In order to generate the build rates, the adjustable could be set under 1.5 degrees, drill until the kick-off depth is reached, trip out and re-adjust the bend angle, trip in and orient to create the build, then trip out and re-adjust once more to an angle under 1.5 degrees and complete the horizontal component of the well. For directional or horizontal drilling, various combinations of motor bend angles and bearing assembly stabilization may be utilized to generate the desired build rates. AIR DRILLING When any type of compressible medium is used in the drilling fluid, the performance of the power section may change dramatically. High air, nitrogen, natural gas, etc, concentrations alter the density of the fluid thus changing how the heat is generated or dissipated, the friction on the power section elastomer and even the power generated. The amount of gas to liquid content on a volume basis will largely determine the how different the power section will behave. Once the fluid content exceeds 75% of the total volume, the compressibility of the total medium is low enough that it is negligible. To maintain the correct total volume and flow rate, especially at higher temperatures, the volume of the gas and/or flow rate may have to be increased to account for the compression. 12

Cougar DS Motor Operations Care should be taken when running a Cougar Drilling Solutions motor in low liquid content to reduce the wear of the motor components and power section. Lubrication should be added to reduce the friction between the rotor and stator and the internal motor component (those exposed to the drilling fluid). Lubricants should be thoroughly mixed and injected into the drilling medium at a rate of no less than 5% of the drilling medium volume. More lubricant reduces wear and cools the power section but it also changes the liquid to gas ratio. The dump valve ports will have to be plugged in order to work with low liquid content. The pressure drop and fluid momentum present with air drilling are not sufficient to close the dump valve. Another consideration is that air drilling does not have the damping characteristics that fluid drilling possesses. As such, applying the weight to the bit from start-up must be done more slowly. The motor must be started slowly and not allowed to spin freely. Low amounts of fluid (Mist: Liquid is < 2.5% of total volume) causes the liquid to form droplets in the gas. This can create problems with corrosion so oxidation inhibitors may be required. 13

Cougar DS Motor Operations Moderate amounts of fluid (Foam: Liquid is between 2.5% to 25% of total volume) allows the liquid and gas to mix reasonably well and provides better lubrication to the power section than a mist would. Foams are typically rated as Foam Quality where the percentage is in gas per volume, i.e. 8% foam quality means 8% gas and 2% liquid. Moderate to normal amounts of fluid (Aerated: liquid is between 25% to 75% of total volume) cause the gas bubbles to be suspended within the liquid. The motor could be started with fluid to prevent over spinning the motor. The weight must be removed slowly (or allowed to drill off) as the pressure is decreased. 14

Cougar DS Motor Operations H 2S (SOUR) GAS The National Association of Corrosion Engineers (NACE) has produced a specification (MR175) that provides a range of material hardness values that are suitable for sour gas use. The Cougar Drilling Solutions motor uses materials with hardness that exceeds the NACE specification. The materials have been chosen to maximize the strength of the component. H 2 S causes embrittlement, which increases the probability to initiate cracking. When running the motor in a sour gas environment, care must be taken to control the environment as much as possible. Damage to the seals or power section is also possible from H 2 S. The length of the exposure is directly proportional to the risk of damage. The average motor run is usually not long enough to cause damage. However, extended runs may cause damage to the elastomers and reduce the life of the tool. Various regulatory or specifications are available which provide information on how to control the sour gas environment. API and NACE are two such sources. 15

Cougar DS Motor Operations SURFACE TESTING Before the motor is used, it should be tested at surface level before being run-in. The Cougar Drilling Solutions motor does not require the differential pressure of the bit and therefore it can be tested at surface. If the motor has a dump valve then it should be tested below the BOP s so the drilling fluid is kept in the system. Make sure to remove any thread protectors if testing below the BOP without the bit. Once the dump valve is close, rotation of the motor should start and torque should be noted in the assembly. Once the pumps are turned off, the valve should open and the pressure should drop. If it doesn t, open the fill-line to the standpipe to relieve the pressure. Now that the motor has been tested, connect whatever bit is desired, make any adjustments to the adjustable housing (if present) and orient the tool by whatever means are present. Then run the motor into the hole. RUNNING IN For the most part, a Cougar Drilling Solutions motor can be run into the hole in a similar fashion as a conventional drilling tool. Extra care is warranted if the motor is set to a high angle on the adjustable or fixed housing. The motor may become stuck in the BOP, casing shoes or liner hangers. The motor may need to be running when navigating tight regions of the bore hole. This procedure should not be used within the cased portion of the well. If the well depth is deep, it may be worthwhile to periodically stop the run-in and circulate to prevent the bit from plugging and to pump cool fluid to the motor which will reduce the chance of the motor becoming too hot causing stator chunking problems. 16

Cougar DS Motor Operations During this time it may be prudent to move the motor up and down slightly so the bit rotation does not form ledges in the casing or to the well bore if in open hole. Care should be taken to prevent backpressure on the motor. It may cause the motor to turn in reverse and increases the chance of un-screwing the internal connections. REACTIVE TORQUE Since the motor causes a right hand rotation, when viewed from the rig floor, the reactive torque is left-hand or counter clockwise. This reactive torque can cause the drill string connections to tighten if the torque exceeds the initial make-up torque. The reactive torque results in twisting the drill string and therefore must be considered when orienting the motor. The measurement of tool face, azimuth and inclination will likely be more accurate than calculating the angle of twist from the drill string properties. However, given the torque, length and diameters of the drilling assembly components, the angle of twist can be calculated using the following: Where: Twist = TL 18 JG π T is the Torque J is the polar moment of Inertia L is the length of the segment G is the modulus of Rigidity for the material (steel) Twist is the angle in degrees The twist is a linear quantity and can be calculated on a per section basis. ie: The twist of the drill pipe plus the twist of the heavy weight plus the twist of the drill collars, etc. 17

Cougar DS Motor Operations RULE OF THUMB GUIDELINES 3 1/2-13.3 /ft Drill Pipe 8 1/2 /1 -ft Torque/1 ft 19 /1 Nm Torque/1 m 3 1/2-15.5 /ft Drill Pipe 7 1/2 /1 -ft Torque/1 ft 17 /1 Nm Torque/1 m 4 1/2-16.6 /ft Drill Pipe 3 1/3 /1 -ft Torque/1 ft 7 1/2 /1 Nm Torque/1 m 5 1/2-19.5 /ft Drill Pipe 2 5/8 /1 -ft Torque/1 ft 6 /1 Nm Torque/1 m MOTOR STALL Motor stall is when the bit stops rotating. This can occur either from excessive weight applied to the bit or from the bit becoming stuck. In either case the reactive torque will increase and if not properly released may cause excessive damage to motor components and possibly other tools in the assembly. Caution must be taken when releasing stored reactive torque as releasing it suddenly may cause connections to backoff. Continued circulation through a stalled motor may cause excessive wear to the elastomer in the power section. A motor stalling can be seen as a sudden pressure increase on the standpipe pressure indicators. 18

Cougar DS Motor Operations The following procedure should be used in order to continue drilling: Stop any drill string rotation iediately. Continued rotation will only increase the torque in the assembly. Back off completely on the pumps before lifting off the bottom. Release the torque. Use the break to slowly release the torque from the drill string. Raise the bit. By lifting the bit off bottom you will be able to increase flow once again to initiate rotation similar to the start-up procedure. ROTATING THE MOTOR To reduce the effects of rotating bending/cyclic fatigue, a balance must be made between the rotation speed and the motor bend angle versus the build rate. For a straight hole with a straight motor, the likelihood of bending is very low so there is minimal concern of bending fatigue. As the build rate increases the bending stresses in the motor increase. In addition to this, as the bend angle of the motor increases, this also increases the bending stresses in the tool. The ideal rotary speed is a function of bend angle and build rate. As a rule of thumb, a rotary speed of 5 RPM and a bend angle of 1.5 or less can be used to reduce the bending fatigue in the motor. From previous experience, 9% of the time the drilling parameters are such that this rule of thumb should work. When the bend angle and build rates are set high, then the rotary speed and the length of time the motor is rotated should be reduced to lessen the effects of rotational bending. 19

Cougar DS Motor Operations ROTOR BYPASS In the event that the flow rate is not sufficient to perform adequate hole cleaning, the rotor can be fitted with a by pass jet. This enables some of the fluid to pass through the bore of the rotor while maintaining the differential pressure. This way the performance characteristics of a given power section can be maintained without over flowing or excessive pressure. The jet size is selected such that the pressure drop around the rotor and through the rotor is equal. In order to do this, a specific pressure and flow rate must be specified and is usually at the desired drilling torque and flow. In this case, when starting the motor, the flow rates are less and there is no torque. Therefore, the pressure balance is off and may require more fluid to initiate rotation than a power section without a bypass jet. MOTOR PRESSURE DROP The pressure drop across the motor is a function of the flow rate. The fluid travels through the dump valve, the drive assembly and the bearing assembly creating a pressure drop due to the restriction of flow. Therefore, the pressure drop across these components is a function of flow rate and viscosity only. Note that, the viscosity has little effect on the pressure drop of the bearing assembly and the drive assembly compared to the pressure drop across the power section. 2

Cougar DS Motor Operations The pressure drop across the power section is a function of the torque and increases linearly with the torque assuming a constant flow rate. Running the power section at differential pressures or flow rates higher than specified will result in premature wear to the elastomer and will degrade performance. BIT PRESSURE DROP The pressure drop created by the bit may be high. When the static pressure drop exceeds 1,5 PSI (1, kpa) the motors will require alternate sealing. Cougar Drilling Solutions should be notified when the bit pressure drop is expected to exceed 1,5 PSI for any length of time. PLUGGING OFF Cuttings and other debris in the well may enter the motor causing a blockage. They may enter the motor through the dump valve ports or as connections are made-up. To prevent this, the hole should be circulated to ensure that the cuttings and debris have been removed leaving the well in as clean a state as possible. If the problem persists, the filter plugs in the dump valve ports may have to be replaced with solid plugs. 21

Cougar DS Motor Operations PULLING OUT When the motor is to be withdrawn from the hole, no special procedure is required when a dump valve is present. The standpipe will drain into the annulus normally. When a dump valve is not present, the fluid will have to drain through the motor. It may be worthwhile to circulate off bottom to remove any cuttings from the annulus before removing the motor. Caution should be used when retrieving a bent motor through the BOP s. Rotating while removing the motor may aid the removal process. It is good practice, after operating the tool, to flush it. This will remove any contaminants or fluids that could freeze, and cause problems. To flush the tool, hold the Bearing Housing (first housing above the Bit Box) and rotate the Bit Box clockwise (CW). CW rotation is normal bit rotation. Caution should be taken at the start of this operation; if the Bit Box will not turn freely, discontinue. Continuing could cause an internal connection to back off. If the Bit Box does turn freely, continue rotation until flow discontinues through the Bit Box. As the motor is being flushed or the bit box rotated, listen for any unusual noises emitting from the internal components. This will give an indication to the presence of any damage. Also, check the surface of the tool for missing oil plugs. If the tool is not rotating properly or there are oil plugs missing, return the tool for servicing. If the motor is to be re-run, check the oil level by using the dip stick and check the depth of the piston. As the oil seeps from the tool the piston moves down (towards the bit). If the tool contains enough oil, it may be re-used. If not, the tool should be returned for servicing. 22

Cougar DS Motor Operations DRILLING FLUIDS Many drilling fluids and additives are available. Some of the fluids and/or additives may be harmful to the elastomers used in the power section as well as the motor seals. Care should be taken when selecting the fluid for use with a Cougar Drilling Solutions motor. Some factors to consider are: The ph of the fluid. The percent of hydrogen is an indication of how acidic or basic the fluid is. A drilling fluid too acidic (ph<4) or too basic (ph>1) will result in damage to the power section. Fluids close to these boundaries may be used but circulation must be maintained to reduce the damage to the elastomers. Acids may also harm plated or coated motor components. After using acid based fluids the motor should be properly flushed and serviced as soon as possible. The particulate content. As the particulate content increases, erosion becomes a serious problem with the elastomers and the internal motor components. Abrasive particulates should be limited to less than 1%. Chlorine content. When the drilling fluid contains a chlorine concentration over 3, PPM (parts per million) the motor must be properly flushed and serviced as soon as possible. The chloride can form acids and increase the corrosion of the motor components. 23

Cougar DS Motor Operations Mud weight. In general, as the mud weight increases the erosion of internal components increases. Usually the increase in weight is largely due to increased amounts of particulates. It is possible to have more erosion with a lighter fluid with high particulates than a heavier fluid with less particulates. For this reason, it is difficult to establish a specific guideline but once the mud weight approaches 15 PPG (pounds per gallon) care must be given that the particulates are being controlled. Light weight, fine particle LCM (loss circulation materials). The fluid path through the motor is somewhat torturous and may result in blockage if coarse LCM materials are used. A coon rule of thumb is 2 s per barrel or less. No cement. Cement should not be pumped through a motor as the cement may flash set while going through various components of the motor or the bit jets. The operation temperature must be below the aniline point. For oil-based fluids, the aniline point gives an indication to the amount of elastomer swell that may be experienced. It is a measure of the oil s aromatic content. Oil based fluids should have an aromatic content less than 2%. The lower the aniline point, the greater the amount of swell the elastomer may undergo. It is recoended that the power section be re-lined after being used in oil-based fluids. Diesel based fluids tend to have a more adverse effect on the elastomers than mineral or low-toxicity fluids. A shorter motor run may be required if the guidelines stated herein are not followed. 24

Cougar DS Motor Operations DOWNHOLE TEMPERATURE The elastomers used in the power section and the seals in the motor are susceptible to temperatures over 25 F (121 C). If the static operating temperature is expected to exceed 25 F then alternate materials for seals and an oversized power section may be required. The over-sized power section has more clearance between the stator and the rotor allowing for more swelling in the elastomer. If extreme temperatures warrant, alternate materials are even possible for the stator elastomer. The motors have been used in temperatures in excess of 25 F (121 C) with good performance. If temperatures exceed 25 F please contact a Cougar Drilling Solutions representative for the proper hot hole configuration. As the temperature increases, the full load differential pressure decreases. Performance may differ from published data when the hole temperature exceeds 14 F (6 C). The stator may require a re-line if run for long periods in high temperatures. 25

Cougar DS Motor Operations TROUBLESHOOTING DECREASE IN ROP Worn stator. This has the effect of reducing the available torque. Increase in hole drag. This could be from a stabilizer hanging up or similar events. Poor bit type for the type of formation. Worn bit. Formation change may require different operating parameters. Motor stalled. SUDDEN PRESSURE INCREASE Motor stall. May be from excessive weight on bit or from hot hole swelling the elastomer in the power section. Internal plug. There may be a restriction in the drilling assembly. If a dump valve is present, the flow could be reduced to see if the pressure stabilizes by allowing the valve to open. This would indicate that the restriction is in the motor. Mud rings. This is when cuttings build around tool joints. They may cause the string to stick. 26

Cougar DS Motor Operations LOW PRESSURE Dump valve is open. All the circulated fluid is dumped into the annulus with little pressure drop. Vary the flow rates in an attempt to close the valve. Washout. There may be a wash out in the assembly causing fluid to flow into the annulus. Worn power section. The ROP would drop. An increase in the differential pressure to regain the ROP is a strong indication that the stator elastomer is worn. 27

Cougar DS Motor Operations ADJUSTABLE INSTRUCTIONS TONG AREA STATOR HOUSING ADAPTOR ADJUSTING RING TONG AREA OFFSET SUB Figure 1 Break Stator Housing Adaptor from adjusting ring using tongs on the tong areas. Ensure adjusting ring remains engaged to offset sub. Now use chain tongs only. Back off stator housing adaptor in 2 full turns. 28

Cougar DS Motor Operations ADJUSTABLE INSTRUCTIONS ADJUSTING RING Figure 2 Place chain tongs on adjusting ring and lift up to disengage teeth. Rotate clockwise to increase bend setting and counter-clockwise to decrease. Align desired bend setting values on adjusting ring with the same number on the offset sub and engage adjusting ring with offset sub. 29

Cougar DS Motor Operations ADJUSTABLE INSTRUCTIONS DOPE FACE WELL BEFORE RETORQUING NOTE: SHOWN SET @ 1.5 TURNED TO SHOW BEND Figure 3 The aligned numbers mark the bend angle and the high side of the bend. Dope the adjusting ring face well and torque the stator housing adaptor to specification (See Table P. 31). Do not allow adjusting ring to rotate CW beyond 3 setting or CCW beyond a setting. If it is not possible to make up the stator housing adaptor to the adjusting ring the adjustable assembly must be reset. See page 31 for resetting instructions. 3

Cougar DS Motor Operations TORQUE SPECIFICATIONS ADJUSTABLE TORQUE VALUES LOWER STABILIZER TORQUE VALUES MOTOR SIZE IMPERIAL (ft-s) METRIC (N-m) IMPERIAL (ft-s) METRIC (N-m) 3 1/8 3, 4, N/A 3 3/4 5, 6,8 N/A 4 3/4 14, 19, 1, 5 14, 19, 1, 6 1/4 33, 44,75 22, 6 1/2 33, 44,75 22, 6 3/4 33, 44,75 22, 8 55, 74,6 27, 9 5/8 85, 115,3 55, N/A N/A 13,56 13,56 29,8 29,8 29,8 36,6 74,57 RESETTING INSTRUCTIONS 1. 2. 3. 4. 5. Back off stator housing adaptor enough to allow adjusting ring to disengage from offset sub. Turn the adjusting ring CW (ie rotary right) until the bent offset mandrel (which is splined to the adjusting ring) bottoms out in the offset sub. **Adjusting ring will no longer rotate in CW direction.** With the adjusting ring still disengaged, rotate CCW until a 3 bend setting is attained (ie 3. on the adjusting ring lines up with 3. on the offset sub). To set to, rotate CCW, until the. s line up. Make up the stator housing adaptor to the adjusting ring while ensuring the adjusting ring remains engaged to the offset sub. 31

Mud Motor Performance Specifications

Motor Chart Example In this example the 6-3/4" (171) 6-7 5. stage motor is used. This example is to show how to get the most from the performance charts. Maximum Pump Rate 6 gpm 2271 Lpm Revolutions per unit volume.292 rev/gal.77 rev/l Pressure at full Load 775 psi 5343 kpa Torque at full load 665 ft 916 N m This table gives a quick suary of the motor performance specifics. The maximum flow rate is the intended maximum flow the motor can receive before damage may occur. The revolutions per unit volume is a direct indication of the RPM's you can expect at a given flow rate. The pressure at full load is the total differential pressure across the motor. The torque at full load is the maximum torque possible when the flow and pressure specifications are met. 2 18 16 14 12 1 8 6 4 2 IMPERIAL PERFORMANCE CURVES { RPM Off-bottom Pressure 3 4 Torque Line 5 6 Torque Maximum & Differential Load 2 4 6 8 DIFFERENTIAL PRESSURE (psi) - - - - Maximum Torque 7 6 5 4 3 2 1 TORQUE (ft ) Drilling Fluid Flow (GPM) 3 4 5 6 (off-bottom pressure) (PSI) 61 83 112 146 (on-bottom - off-bottom pressure) (PSI) 714 692 663 629 This table gives the off-bottom pressure and the maximum effective pressure for a range of flow rates. NOTE: The off-bottom plus the maximum effective equals the total differential pressure. 34

Cougar DS Motor Operations Tool Max Flow Rate gpm lpm Torque at Full Load ft. N-m Max Pressure at Bit Full Load Speed psi kpa rpm 3 1/8 7-8 3. Stage 3 1/8 7-8 4. Stage 3 3/4 4-5 3.5 Stage 3 3/4 7-8 2. Stage 3 3/4 7-8 2.3 Stage 4 3/4 4-5 3.5 Stage 4 3/4 7-8 2. Stage 4 3/4 7-8 2.2 Stage 4 3/4 7-8 2.6 Stage ESX 4 3/4 7-8 3.8 Stage 4 3/4 7-8 4.5 SX Stage 14 53 655 888 6 4137 23 11 416 425 576 75 5171 392 16 66 96 13 53 3654 25 16 66 1556 211 42 2896 8 16 66 111 151 35 238 122 25 95 145 197 53 362 26 25 95 289 388 374 2578 74 25 95 156 212 33 228 14 3 114 35 475 39 264 79 25 95 296 42 57 393 14 3 114 35 4745 68 4688 14 4 3/4 7-8 4.5 SXHR Stage 3 114 525 7118 11 6964 14 5 6-7 6. Stage 5 6-7 7. Stage 6 1/4 7-8 4.8 Stage 6 1/2 4-5 4.8 Stage 6 1/2 6-7 3.1 Stage ERT 6 1/2 6-7 5. Stage 6 1/2 6-7 5. HR Stage 6 1/2 7-8 2.9 Stage Slow 6 1/2 7-8 3. Stage 6 1/2 7-8 3. Stage Slow 6 1/2 7-8 5. Stage 6 1/2 7-8 5. HR Stage 6 1/2 7-8 5.7 Stage 6 1/2 7-8 5.7 HR Stage 6 1/2 8-9 3. Stage 35 1363 2736 3676 147 7219 294 36 1363 3262 4427 1225 8446 294 4 151 574 779 72 496 132 6 2271 2725 3695 674 4647 254 65 2461 8235 11165 1175 895 24 6 227 623 845 75 517 18 6 227 935 1268 113 776 18 5 1893 742 136 56 3861 72 6 2271 419 567 6 313 17 6 2271 72 976 45 31 93 6 2271 698 946 75 5171 18 6 2271 146 1419 113 776 18 6 2271 915 124 86 59 15 6 2271 1372 186 128 884 15 5 1893 49 6644 584 427 17 35

Cougar DS Motor Operations Tool Max Flow Rate gpm lpm Torque at Full Load ft. N-m Max Pressure at Bit Full Load Speed psi kpa rpm 6 3/4 6-7 3.1 Stage ERT 6 3/4 6-7 5. Stage 6 3/4 6-7 5. HR Stage 6 3/4 7-8 2.9 Stage Slow 6 3/4 7-8 3. Stage 6 3/4 7-8 5. Stage 6 3/4 7-8 5. HR Stage 6 3/4 7-8 5.7 Stage 6 3/4 7-8 5.7 HR Stage 8 4-5 3.6 Stage 8 7-8 2. Stage 8 7-8 3.4 ESX3 Stage 8 7-8 4. Stage 8 7-8 4. HR Stage 9 5/8 3-4 4.5 Stage 9 5/8 3-4 6. Stage 9 5/8 5-6 3. Stage 9 5/8 5-6 5. Stage 9 5/8 5-6 5. HR Stage 9 5/8 6-7 5. Stage 11 1/4 3-4 3.6 Stage 11 1/4 5-6 4.6 Stage 65 2461 8235 11165 1175 895 24 6 2271 623 845 75 517 18 6 2271 935 1268 113 776 18 5 1893 742 136 56 3861 72 6 2271 419 5681 45 313 17 6 2271 698 946 75 517 18 6 2271 146 1419 113 776 18 6 2271 915 124 86 59 18 6 2271 1372 186 128 884 145 9 347 4294 5822 497 3427 19 8 328 753 9563 374 2579 77 9 341 143 1939 51 352 8 9 341 995 1349 6 414 15 9 341 1493 224 9 621 15 12 4542 678 9192 62 4275 225 12 4542 8272 11215 765 5275 27 12 4542 194 14833 45 313 14 13 492 1612 2185 75 517 18 13 492 2417 3277 113 776 18 12 4542 1332 1835 775 5343 156 15 568 1339 1816 54 372 174 16 681 218 2956 69 476 142 36

Motor Fishing Dimensions Motor Lobes Stages A B C D E F G H I 3 1/8" (79 ) 3 3/4" (95 ) 5" (127 ) 6 1/4" (159 ) 9 5/8" (244 ) 11 1/4" (286 ) 3. 166. 177.5 194.5 7-8 1 n/a 16 3 48 6 4. 134. 145.5 162.5 4-5 3.5 n/a n/a n/a 7-8 4 3/4" (121 ) 7-8 6 1/2" (165 ) ONLY 2. n/a n/a n/a n/a n/a n/a n/a n/a n/a 2.3 n/a n/a n/a 4-5 3.5 23. 217.5 244. 6-7 6 1/2" (165 ) & 6 3/4" (171 ) 7-8 8" (23 ) 7-8 2. 261. 275.5 32. 2.2 23. 217.5 244. 2.6 ESX 11 18 21 4 64 81 31. 324.5 351. 3.8 268. 282.5 39. 4.5 SX 289.3 33.8 33.3 4.5 SX HR 289.3 33.8 33.3 6. 266. 28.5 37. 11 18 21 4 64 81 7. 293. 37.5 334. 7-8 4.8 14 22 28 52 79 97 227. 253. 279.5 4-5 4.8 25.5 276.5 33. 7-8 3. SLOW 14 22 28 52 79 97 31. 327. 353.5 8-9 3. 228. 254. 28.5 3.1 ERT 224.8 25.8 277.8 6-7 5. 297. 323. 35. 5. HR 297. 323. 35. 2.9 SLOW 317. 343. 369.5 3. 14 22 28 52 79 97 228. 254. 28.5 5. 291.5 317.5 344.5 5. HR 291.5 317.5 344.5 5.7 357. 383. 41. 5.7 HR 357. 383. 41. 4-5 3.6 278. 299.5 33. 2. 278. 299.5 33. 3.4 ESX3 18 28 35 61 9 11 313.2 334.7 365.2 4. 316. 337.5 368. 4. HR 313.2 334.7 365.2 4.5 297. 318.5 349. 3-4 6. 347. 368.5 399. 3. 297. 318.5 349. 17 28 36 63 95 119 5-6 5. 351. 372.5 43. 5. HR 351. 372.5 43. 6-7 5. 327. 348.5 379. 3-4 3.6 355. 379. 49. 19 29 38 67 11 125 5-6 4.6 355. 379. 49. 37

Motor Fishing Dimensions Motor Lobes Stages J K L M N P Q R S 3 1/8" 3. 7-8 (79 ) 4. 3.15 n/a 3.15 3.15 3.15 3.15 3.13 3.15 3.15 4-5 3.5 3 3/4" (95 ) 7-8 2. 3. 7 5 4.2 4.2 3.75 3.75 3.75 3.75 3.75 3.75 2.3 4-5 4 3/4" (121 ) 7-8 3.5 2. 2.2 2.6 ESX 3.8 4.5 SX 4.5 SX HR 4.81 5.38 5.38 4.81 4.81 4.81 4.75 4.75 4.81 5" 6. 6-7 (127 ) 7. 4.81 5.38 5.38 4.81 4.81 4.75 4.75 4.75 4.81 6 1/4" (159 ) 7-8 2.8 6.5 7.19 7.19 6.5 6.62 6.62 6.25 6.37 6.62 6 1/2" 4-5 4.8 (165 ) 7-8 3. SLOW 6.5 7.19 7.19 6.5 6.62 6.62 6.5 6.62 6.62 ONLY 6 1/2" (165 ) & 8-9 6-7 3. 3.1 ERT 5. 5. HR 2.9 SLOW 3. 6.5 7.19 7.19 6.5 6.62 6.62 6.5 6.62 6.62 6 3/4" (171 ) 7-8 5. 5. HR 5.7 5.7 HR 4-5 3.6 8" (23 ) 7-8 3-4 2. 3.4 ESX3 4. 4. HR 4.5 7.81 8.63 8.63 8.6 8.6 8.6 8. 8.6 8.6 6. 9 5/8" 3. (244 ) 5-6 5. 9.75 1.75 1.75 9.75 9.75 9.75 9.625 9.75 9.64 5. HR 6-7 5. 11 1/4" 3-4 3.6 (286 ) 5-6 4.6 1.8 12. 12. 11.25 11.25 11.25 11.25 11.25 11.25 38

Stabilizer Motor Fishing Dimensions Motor Lobes Stages A B C D E F G H 3 1/8" (79 ) 3 3/4" (95 ) 4 3/4" (121 ) 5" (127 ) 6 1/4" (159 ) 6 1/2" (165 ) ONLY 6 1/2" (165 ) & 6 3/4" (171 ) 8" (23 ) 9 5/8" (244 ) 5-6 11 1/4" (286 ) 7-8 3. n/a n/a n/a n/a n/a n/a n/a n/a 4. n/a n/a 4-5 3.5 n/a n/a 7-8 2. n/a n/a n/a n/a n/a n/a n/a n/a 2.3 n/a n/a 4-5 3.5 133.8 25. 7-8 6-7 2. 191.8 38. 2.2 133.8 25. 2.6 ESX 1.3 41.5 45. 12.9 47.4 241.1 56. 357.3 3.8 198.8 315. 4.5 SX 197.9 314.2 4.5 SX HR 197.9 314.2 6. 1.3 41.5 45. 12.9 47.4 196.8 56. 313. 7. 223.8 34. 7-8 4.8 12.3 45.6 42. 15.8 59. 149.8 55.5 28.1 4-5 4.8 173.3 33.6 7-8 3. SLOW 12.3 45.6 42. 15.8 59. 223.8 55.5 354.1 8-9 3. 15.8 281.1 6-7 7-8 3.1 ERT 147.6 277.9 5. 219.8 35.1 5. HR 176. 36.3 2.9 SLOW 239.8 37.1 3. 12.3 45.6 42. 15.8 59. 15.8 55.5 281.1 5. 279.8 41.1 5. HR 213.8 344.1 5.7 176. 36.3 5.7 HR 236. 366.3 4-5 3.6 334.3 7-8 3-4 2. 394.3 3.4 ESX3 15.5 n/a n/a 2.1 n/a n/a n/a 334.3 4. 334.3 4. HR 334.2 4.5 348.3 6. 398.3 3. 16.5 n/a n/a 2.1 n/a n/a n/a 348.3 5. 398. 5. HR 398. 6-7 5. 379. 3-4 3.6 n/a n/a n/a n/a n/a n/a n/a 49. 5-6 4.6 49. 39

3 1/8 (79 ) Mud Motors

3 1/8 (79 ) 7-8 3. Stage A. Distance to stabilizer B. Box to Bend C. Overall Length D. Thread Prot. Diameter E. Kick Pad Diameter N/A 44 N/A 3.36 Imperial N/A 1,118 195 4,95 N/A 85.3 Metric Top Connection Bottom Connection Weight Maximum Flow Rate Maximum Torque Maximum Power Maximum Weight Dynamic on bit Static Maximum Allowable Pull Pull to Yield Motor AS PER REQUEST 2 3/8 Reg 2 3/8 Reg 287 14 655 49 1,85 32,3 32,3 15, gpm ft- hp 128.53 888 37 4,8 14, 14, 67, m 3 /min N-m kw Bend Settings (degrees).26.52.78 1.3 1.27 1.5 1.72 1.93 2.12 2.3 2.6 2.82 2.95 3. Build Rate (degrees/1ft(3 m)) Hole Sizes (in, ) 3 3/4 4 1/8 4 1/2 95 15 114 8.4 11.93 15.47 18.87 22.14 25.26 28.26 31.12 33.7 36.16 4.24 43.24 45.2 45.7 5.5 8.59 12.12 15.52 18.79 21.92 24.91 27.77 3.36 32.81 36.89 39.89 41.67 42.35 1.7 5.24 8.77 12.77 15.44 18.57 21.56 24.42 27.1 29.46 33.54 36.54 38.31 39. 42

3 1/8 (79 ) 7-8 3. Stage Maximum Pump Rate 14 gpm 53 Lpm Revolutions per unit volume 1.643 rev/gal.434 rev/l Pressure at full Load 6 psi 4,137 kpa Torque at full load 655 ft 888 N m 28 IMPERIAL PERFORMANCE CURVES 7 24 14 2 12 16 1 12 8 8 4 2 4 6 Torque DIFFERENTIAL PRESSURE (psi) 6 5 4 3 2 1 TORQUE (ft ) Drilling Fluid Flow (GPM) 8 1 12 14 (off-bottom pressure) (PSI) 14 148 23 268 (on-bottom - off-bottom pressure) (PSI) 496 452 397 332 25 2 15 1 5 METRIC PERFORMANCE CURVES Torque 33 379 454 53 1 2 3 4 DIFFERENTIAL PRESSURE (kpa) 1 8 6 4 2 TORQUE (N m) Drilling Fluid Flow (L/min) 33 379 454 53 (off-bottom pressure) (kpa) 717 12 14 1848 (on-bottom - off-bottom pressure) (kpa) 342 3116 2737 2289 43

3 1/8 (79 ) 7-8 4. Stage A. Distance to stabilizer B. Box to Bend C. Overall Length D. Thread Prot. Diameter E. Kick Pad Diameter N/A 44 N/A 3.36 Imperial N/A 1,118 167 4,239 N/A 85.3 Metric Top Connection Bottom Connection Weight Maximum Flow Rate Maximum Torque Maximum Power Maximum Weight Dynamic on bit Static Maximum Allowable Pull Pull to Yield Motor AS PER REQUEST 2 3/8 Reg 2 3/8 Reg 255 11 425 48 1,85 32,3 32,3 15, gpm ft- hp 113.42 313 36 4,8 14, 14, 67, m 3 /min N-m kw Bend Settings (degrees).26.52.78 1.3 1.27 1.5 1.72 1.93 2.12 2.3 2.6 2.82 2.95 3. Build Rate (degrees/1ft(3 m)) Hole Sizes (in, ) 3 3/4 4 1/8 4 1/2 95 15 114 11.21 15.5 19.8 23.92 27.89 31.68 35.32 38.78 41.93 44.91 49.87 53.52 55.67 56.5 7.14 11.43 15.72 19.85 23.81 27.61 31.24 34.71 37.85 4.83 45.79 49.44 51.59 52.42 3.6 7.35 11.65 15.77 19.73 23.53 27.17 3.64 33.78 36.75 41.71 45.35 47.51 48.34 44

3 1/8 (79 ) 7-8 4. Stage Maximum Pump Rate 11 gpm 416 Lpm Revolutions per unit volume 3.564 rev/gal.941 rev/l Pressure at full Load 75 psi 5171 kpa Torque at full load 425 ft 576 N m 4 IMPERIAL PERFORMANCE CURVES 11 5 4 3 2 1 1 8 7 2 4 6 8 DIFFERENTIAL PRESSURE (psi) 3 2 1 TORQUE (ft ) Drilling Fluid Flow (GPM) 7 8 1 11 (off-bottom pressure) (PSI) 11 123 177 28 (on-bottom minus off-bottom pressure) (PSI) 649 627 573 542 4 3 2 1 METRIC PERFORMANCE CURVES 416 379 33 265 2 4 6 7 6 5 4 3 2 1 TORQUE (N m) DIFFERENTIAL PRESSURE (kpa) Drilling Fluid Flow (L/min) 265 33 379 416 (off-bottom pressure) (kpa) 696 848 122 1434 (on-bottom minus off-bottom pressure) (kpa) 4475 4323 3951 3737 45

3 3/4 (95 ) Mud Motors

3 3/4 (95 ) 4-5 3.5 Stage A. Distance to stabilizer B. Box to Bend C. Overall Length D. Thread Prot. Diameter E. Kick Pad Diameter Imperial Metric N/A 44 227 4.38 4. N/A 1,118 5,766 111 12 Top Connection Bottom Connection Weight Maximum Flow Rate Maximum Torque Maximum Power Maximum Weight Dynamic on bit Static Maximum Allowable Pull Pull to Yield Motor AS PER REQUEST 2 7/8 Reg 2 7/8 Reg 425 16 96 39 2, 61, 61, 15, gpm ft- hp 189.61 1,3 29 8,9 27, 27, 67, m 3 /min N-m kw Bend Settings (degrees).26.52.78 1.3 1.27 1.5 1.72 1.93 2.12 2.3 2.6 2.82 2.95 3. Build Rate (degrees/1ft(3 m)) Hole Sizes (in, ) 4 3/4 5 1/4 5 7/8 121 133 149..81 3.75 6.58 9.29 11.89 14.38 16.75 18.9 2.94 24.33 26.82 28.3 28.86...5 2.87 5.59 8.19 1.67 13.5 15.2 17.23 2.63 23.12 24.59 25.16.....96 3.56 6.4 8.42 1.57 12.6 16. 18.49 19.96 2.52 48

3 3/4 (95 ) 4-5 3.5 Stage Maximum Pump Rate 16 gpm 66 Lpm Revolutions per unit volume 1.55 rev/gal.41 rev/l Pressure at full Load 53 psi 3,654 kpa Torque at full load 96 ft 1,3 N m 3 IMPERIAL PERFORMANCE CURVES 12 25 2 15 1 5 8 Torque 1 12 16 1 2 3 4 5 6 DIFFERENTIAL PRESSURE (psi) 1 8 6 4 2 TORQUE (ft ) Drilling Fluid Flow (GPM) 8 1 12 16 (off-bottom pressure) (PSI) 57 72 85 96 (on-bottom - off-bottom pressure) (PSI) 473 458 445 434 3 METRIC PERFORMANCE CURVES 14 25 2 15 1 5 379 33 Torque 454 66 1 2 3 4 DIFFERENTIAL PRESSURE (kpa) 12 1 8 6 4 2 TORQUE (N m) Drilling Fluid Flow (L/min) 33 379 454 66 (off-bottom pressure) (kpa) 393 496 586 662 (on-bottom - off-bottom pressure) (kpa) 3261 3158 368 2992 49

3 3/4 (95 ) 7-8 2. Stage A. Distance to stabilizer B. Box to Bend C. Overall Length D. Thread Prot. Diameter E. Kick Pad Diameter Imperial Metric N/A 44 252 4.38 4. N/A 1,118 6,41 111 12 Top Connection Bottom Connection Weight Maximum Flow Rate Maximum Torque Maximum Power Maximum Weight Dynamic on bit Static Maximum Allowable Pull Pull to Yield Motor AS PER REQUEST 2 7/8 Reg 2 7/8 Reg 491 16 1,556 39 2, 61, 61, 15, gpm ft- hp 218.61 2,11 29 8,9 27, 27, 67, m 3 /min N-m kw Bend Settings (degrees).26.52.78 1.3 1.27 1.5 1.72 1.93 2.12 2.3 2.6 2.82 2.95 3. Build Rate (degrees/1ft(3 m)) Hole Sizes (in, ) 4 3/4 5 1/4 5 7/8 121 133 149..8 3.8 6.6 9.3 11.9 14.4 16.8 18.9 2.9 24.3 26.8 28.3 28.9...1 2.9 5.6 8.2 1.7 13.1 15.2 17.2 2.6 23.1 24.6 25.2.... 1. 3.6 6. 8.4 1.6 13.6 16. 18.5 2. 2.5 5

3 3/4 (95 ) 7-8 2. Stage Maximum Pump Rate 16 gpm 66 Lpm Revolutions per unit volume.5 rev/gal.132 rev/l Pressure at full Load 42 psi 2,896 kpa Torque at full load 1,556 ft 2,11 N m 1 IMPERIAL PERFORMANCE CURVES 2 8 6 4 2 Torque 1 12 14 16 1 2 3 4 5 DIFFERENTIAL PRESSURE (psi) 16 12 8 4 TORQUE (ft ) Drilling Fluid Flow (GPM) 1 12 14 16 (off-bottom pressure) (PSI) 89 121 158 2 (on-bottom - off-bottom pressure) (PSI) 331 299 262 22 1 METRIC PERFORMANCE CURVES 25 8 6 4 2 Torque 454 379 66 53 1 2 3 DIFFERENTIAL PRESSURE (kpa) 2 15 1 5 TORQUE (N m) Drilling Fluid Flow (L/min) 379 454 53 66 (off-bottom pressure) (kpa) 614 834 189 1379 (on-bottom - off-bottom pressure) (kpa) 2282 262 186 1517 51

3 3/4 (95 ) 7-8 2.3 Stage A. Distance to stabilizer B. Box to Bend C. Overall Length D. Thread Prot. Diameter E. Kick Pad Diameter Imperial Metric N/A 44 233 4.38 4. N/A 1,118 5,918 111 12 Top Connection Bottom Connection Weight Maximum Flow Rate Maximum Torque Maximum Power Maximum Weight Dynamic on bit Static Maximum Allowable Pull Pull to Yield Motor AS PER REQUEST 2 7/8 Reg 2 7/8 Reg 428 16 1,11 18 2, 61, 61, 15, gpm ft- hp 19.61 1,51 13 8,9 27, 27, 67, m 3 /min N-m kw Bend Settings (degrees).26.52.78 1.3 1.27 1.5 1.72 1.93 2.12 2.3 2.6 2.82 2.95 3. Build Rate (degrees/1ft(3 m)) Hole Sizes (in, ) 4 3/4 5 1/4 5 7/8 121 133 149..81 3.75 6.58 9.29 11.89 14.38 16.75 18.9 2.94 24.33 26.82 28.3 28.86...5 2.87 5.59 8.19 1.67 13.5 15.2 17.23 2.63 23.12 24.59 25.16.....96 3.56 6.4 8.42 1.57 12.6 16. 18.49 19.96 2.52 52

3 3/4 (95 ) 7-8 2.3 Stage Maximum Pump Rate 16 gpm 66 Lpm Revolutions per unit volume.768 rev/gal.23 rev/l Pressure at full Load 35 psi 2,38 kpa Torque at full load 1,11 ft 1,51 N m 14 IMPERIAL PERFORMANCE CURVES 12 12 1 8 6 4 2 14 12 1 16 8 4 TORQUE (ft ) 1 2 3 4 DIFFERENTIAL PRESSURE (psi) Drilling Fluid Flow (GPM) 1 12 14 16 (off-bottom pressure) (PSI) 5 73 112 157 (on-bottom minus off-bottom pressure) (PSI) 3 277 238 193 14 METRIC PERFORMANCE CURVES 16 12 1 8 6 4 2 66 53 454 379 5 1 15 2 25 DIFFERENTIAL PRESSURE (kpa) 12 8 4 TORQUE (N m) Drilling Fluid Flow (L/min) 379 454 53 66 (off-bottom pressure) (kpa) 345 53 772 182 (on-bottom minus off-bottom pressure) (kpa) 268 191 1641 1331 53

4 3/4 (121 ) Mud Motors

4 3/4 (121 ) 4-5 3.5 Stage A. Distance to stabilizer B. Box to Bend C. Overall Length D. Thread Prot. Diameter E. Kick Pad Diameter 18 62 5.38 5.25 Imperial 457 1,575 245 6,223 137 133 Metric Top Connection Bottom Connection Weight Maximum Flow Rate Maximum Torque Maximum Power Maximum Weight Dynamic on bit Static Maximum Allowable Pull Pull to Yield Motor AS PER REQUEST 3 1/2 Reg 3 1/2 Reg 819 25 1,45 61 43, 118, 118, 2, gpm ft- hp 364.95 1,97 45 19, 52, 52, 9, m 3 /min N-m kw Bend Settings (degrees).26.52.78 1.3 1.27 1.5 1.72 1.93 2.12 2.3 2.6 2.82 2.95 3. Build Rate (degrees/1ft(3 m)) Hole Sizes (in, ) 5 7/8 6 1/8 6 1/4 149 156 159 6 3/4 171.94.28.89. 3.84 2.62 2.1.43 6.74 5.52 4.91 2.47 9.52 8.3 7.69 5.25 12.2 1.98 1.37 7.93 14.76 13.54 12.93 1.49 17.22 16. 15.39 12.95 19.56 18.34 17.73 15.29 21.68 2.46 19.85 17.41 23.69 22.47 21.86 19.42 27.4 25.82 25.21 22.77 29.5 28.28 27.67 25.23 3.96 29.74 29.12 26.68 31.52 3.29 29.68 27.24 56

4 3/4 (121 ) 4-5 3.5 Stage Maximum Pump Rate 25 gpm 95 Lpm Revolutions per unit volume 1.2 rev/gal.27 rev/l Pressure at full Load 53 psi 3,62 kpa Torque at full load 1,45 ft 1,97 N m 3 25 2 15 1 5 IMPERIAL PERFORMANCE CURVES 1 Torque 15 2 25 1 2 3 4 5 6 DIFFERENTIAL PRESSURE (psi) 16 14 12 1 8 6 4 2 TORQUE (ft ) Drilling Fluid Flow (GPM) 1 15 2 25 (off-bottom pressure) (PSI) 49 56 69 81 (on-bottom - off-bottom pressure) (PSI) 481 474 461 449 3 25 METRIC PERFORMANCE CURVES 946 25 2 2 15 1 5 379 Torque 568 757 1 2 3 4 DIFFERENTIAL PRESSURE (kpa) 15 1 5 TORQUE (N m) Drilling Fluid Flow (L/min) 379 568 757 946 (off-bottom pressure) (kpa) 338 386 476 558 (on-bottom - off-bottom pressure) (kpa) 3316 3268 3178 396 57

4 3/4 (121 ) 7-8 2. Stage A. Distance to stabilizer B. Box to Bend C. Overall Length D. Thread Prot. Diameter E. Kick Pad Diameter 18 62 5.38 5.25 Imperial 457 1,575 39 7,849 137 133 Metric Top Connection Bottom Connection Weight Maximum Flow Rate Maximum Torque Maximum Power Maximum Weight Dynamic on bit Static Maximum Allowable Pull Pull to Yield Motor AS PER REQUEST 3 1/2 Reg 3 1/2 Reg 1,25 25 2,89 55 43, 118, 118, 2, gpm ft- hp 456.95 3,88 41 19, 52, 52, 9, m 3 /min N-m kw Bend Settings (degrees).26.52.78 1.3 1.27 1.5 1.72 1.93 2.12 2.3 2.6 2.82 2.95 3. Build Rate (degrees/1ft(3 m)) Hole Sizes (in, ) 5 7/8 6 1/8 6 1/4 149 156 159 6 3/4 171.5.46.94. 2.79 1.83 1.35.57 5.8 4.12 3.64 1.72 7.28 6.32 5.84 3.92 9.39 8.43 7.95 6.3 11.42 1.46 9.98 8.5 13.35 12.39 11.91 9.99 15.2 14.24 13.67 11.84 16.88 15.91 15.43 13.51 18.46 17.5 17.2 15.1 21.11 2.15 19.66 17.74 23.5 22.8 21.6 19.68 24.19 23.23 22.75 2.83 24.63 23.67 23.19 21.27 58

4 3/4 (121 ) 7-8 2. Stage Maximum Pump Rate 25 gpm 95 Lpm Revolutions per unit volume.296 rev/gal.78 rev/l Pressure at full Load 374 psi 2578 kpa Torque at full load 2,89 ft 3,88 N m 8 7 6 5 4 3 2 1 IMPERIAL PERFORMANCE CURVES 25 2 15 1 1 2 3 4 DIFFERENTIAL PRESSURE (psi) 3 25 2 15 1 5 TORQUE (ft ) Drilling Fluid Flow (GPM) 1 15 2 25 (off-bottom pressure) (PSI) 37 62 88 123 (on-bottom minus off-bottom pressure) (PSI) 337 312 286 251 8 7 6 5 4 3 2 1 METRIC PERFORMANCE CURVES 946 757 568 379 1 2 3 DIFFERENTIAL PRESSURE (kpa) 4 3 2 1 TORQUE (N m) Drilling Fluid Flow (L/min) 379 568 757 946 (off-bottom pressure) (kpa) 255 427 67 848 (on-bottom minus off-bottom pressure) (kpa) 2324 2151 1972 1731 59

4 3/4 (121 ) 7-8 2.2 Stage A. Distance to stabilizer B. Box to Bend C. Overall Length D. Thread Prot. Diameter E. Kick Pad Diameter 18 62 5.38 5.25 Imperial 457 1,575 245 6,223 137 133 Metric Top Connection Bottom Connection Weight Maximum Flow Rate Maximum Torque Maximum Power Maximum Weight Dynamic on bit Static Maximum Allowable Pull Pull to Yield Motor AS PER REQUEST 3 1/2 Reg 3 1/2 Reg 1,181 25 1,56 33 43, 118, 118, 2, gpm ft- hp 525.95 2,12 24 19, 52, 52, 9, m 3 /min N-m kw Bend Settings (degrees).26.52.78 1.3 1.27 1.5 1.72 1.93 2.12 2.3 2.6 2.82 2.95 3. Build Rate (degrees/1ft(3 m)) Hole Sizes (in, ) 5 7/8 6 1/8 6 1/4 149 156 159 6 3/4 171.89.31.9. 3.72 2.53 1.93.48 6.56 5.36 4.77 2.38 9.28 8.9 7.49 5.11 11.9 1.71 1.11 7.73 14.41 13.22 12.62 1.23 16.81 15.62 15.2 12.63 19.1 17.91 17.31 14.93 21.18 19.98 19.39 17. 23.14 21.95 21.35 18.97 26.42 25.23 24.63 22.24 28.83 27.63 27.4 24.65 3.25 29.6 28.46 25.85 3.8 29.6 29.1 26.62 6

4 3/4 (121 ) 7-8 2.2 Stage Maximum Pump Rate 25 gpm 95 Lpm Revolutions per unit volume.522 rev/gal.138 rev/l Pressure at full Load 33 psi 2,28 kpa Torque at full load 1,56 ft 2,12 N m 16 14 12 1 8 6 4 2 IMPERIAL PERFORMANCE CURVES Torque 1 15 2 25 1 2 3 4 DIFFERENTIAL PRESSURE (psi) 18 16 14 12 1 8 6 4 2 TORQUE (ft ) Drilling Fluid Flow (GPM) 1 15 2 25 (off-bottom pressure) (PSI) 29 41 73 17 (on-bottom - off-bottom pressure) (PSI) 31 289 257 223 16 14 12 1 8 6 4 2 Torque METRIC PERFORMANCE CURVES 379 568 757 946 5 1 15 2 25 DIFFERENTIAL PRESSURE (kpa) 25 2 15 1 5 TORQUE (N m) Drilling Fluid Flow (L/min) 379 568 757 946 (off-bottom pressure) (kpa) 2 283 53 738 (on-bottom - off-bottom pressure) (kpa) 275 1993 1772 1538 61

4 3/4 (121 ) 7-8 2.6 Stage ESX A. Distance to stabilizer B. Box to Bend C. Overall Length D. Thread Prot. Diameter E. Kick Pad Diameter 18 62 5.38 5.25 Imperial 457 1,575 346 8,788 137 133 Metric Top Connection Bottom Connection Weight Maximum Flow Rate Maximum Torque Maximum Power Maximum Weight Dynamic on bit Static Maximum Allowable Pull Pull to Yield Motor AS PER REQUEST 3 1/2 Reg 3 1/2 Reg 1,164 3 3,5 46 43, 118, 118, 2, gpm ft- hp 518 1.14 4,75 35 19, 52, 52, 9, m 3 /min N-m kw Bend Settings (degrees).26.52.78 1.3 1.27 1.5 1.72 1.93 2.12 2.3 2.6 2.82 2.95 3. Build Rate (degrees/1ft(3 m)) Hole Sizes (in, ) 5 7/8 6 1/8 6 1/4 149 156 159 6 3/4 171.33.48.89. 2.27 1.45 1.5.58 4.2 3.39 2.99 1.36 6.7 5.26 4.85 3.22 7.86 7.5 6.64 5.1 9.57 8.76 8.35 6.73 11.22 1.4 1. 8.37 12.78 11.97 11.56 9.94 14.2 13.39 12.98 11.35 15.54 14.73 14.32 12.7 17.78 16.97 16.56 14.94 19.43 18.61 18.21 16.58 2.4 19.58 19.18 17.55 2.77 19.96 19.55 17.92 62

4 3/4 (121 ) 7-8 2.6 Stage ESX Maximum Pump Rate 3 gpm 1,14 Lpm Revolutions per unit volume.263 rev/gal.7 rev/l Pressure at full Load 39 psi 2,69 kpa Torque at full load 3,5 ft 4,75 N m 9 8 7 6 5 4 3 2 1 IMPERIAL PERFORMANCE CURVES Torque 15 225 3 275 1 2 3 4 DIFFERENTIAL PRESSURE (psi) 4 3 2 1 TORQUE (ft ) Drilling Fluid Flow (GPM) 15 225 275 3 (off-bottom pressure) (PSI) 34 62 11 152 (on-bottom - off-bottom pressure) (PSI) 356 328 289 238 9 8 7 6 5 4 3 2 1 METRIC PERFORMANCE CURVES 568 Torque 852 1136 141 5 1 15 2 25 3 DIFFERENTIAL PRESSURE (kpa) 5 4 3 2 1 TORQUE (N m) Drilling Fluid Flow (L/min) 568 852 141 1136 (off-bottom pressure) (kpa) 234 427 696 148 (on-bottom - off-bottom pressure) (kpa) 2455 2261 1993 1641 63

4 3/4 (121 ) 7-8 3.8 Stage A. Distance to stabilizer B. Box to Bend C. Overall Length D. Thread Prot. Diameter E. Kick Pad Diameter 18 62 5.38 5.25 Imperial 457 1,575 316 8,26 137 133 Metric Top Connection Bottom Connection Weight Maximum Flow Rate Maximum Torque Maximum Power Maximum Weight Dynamic on bit Static Maximum Allowable Pull Pull to Yield Motor AS PER REQUEST 3 1/2 Reg 3 1/2 Reg 1,78 25 2,96 65 43, 118, 118, 2, gpm ft- hp 48.95 4,2 49 19, 52, 52, 9, m 3 /min N-m kw Bend Settings (degrees).26.52.78 1.3 1.27 1.5 1.72 1.93 2.12 2.3 2.6 2.82 2.95 3. Build Rate (degrees/1ft(3 m)) Hole Sizes (in, ) 5 7/8 6 1/8 6 1/4 149 156 159 6 3/4 171.47.46.93. 2.7 1.76 1.3.58 4.93 3.99 3.53 1.65 7.7 6.14 5.67 3.8 9.13 8.19 7.73 5.86 11.1 1.17 9.7 7.83 12.99 12.2 11.59 9.71 14.79 13.86 13.39 11.52 16.42 15.49 15.2 13.15 17.97 17.3 16.56 14.69 2.54 19.31 19.14 17.27 22.43 21.5 21.3 19.16 23.55 22.61 22.15 2.27 23.98 23.4 22.58 2.7 64

4 3/4 (121 ) 7-8 3.8 Stage Maximum Pump Rate 25 gpm 95 Lpm Revolutions per unit volume.56 rev/gal.148 rev/l Pressure at full Load 57 psi 3,93 kpa Torque at full load 2,96 ft 4,2 N m 14 12 1 8 6 4 2 IMPERIAL PERFORMANCE CURVES 15 Torque 175 2 25 1 2 3 4 5 6 DIFFERENTIAL PRESSURE (psi) 3 25 2 15 1 5 TORQUE (ft ) Drilling Fluid Flow (GPM) 15 175 2 25 (off-bottom pressure) (PSI) 42 61 87 18 (on-bottom - off-bottom pressure) (PSI) 58 489 463 442 14 12 1 8 6 4 2 METRIC PERFORMANCE CURVES 568 Torque 662 757 946 1 2 3 4 DIFFERENTIAL PRESSURE (kpa) 4 3 2 1 TORQUE (N m) Drilling Fluid Flow (L/min) 568 662 757 946 (off-bottom pressure) (kpa) 29 421 6 745 (on-bottom - off-bottom pressure) (kpa) 353 3372 3192 347 65

4 3/4 (121 ) 7-8 4.5 SX Stage A. Distance to stabilizer B. Box to Bend C. Overall Length D. Thread Prot. Diameter E. Kick Pad Diameter 18 62 5.38 5.25 Imperial 457 1,575 358 911 137 133 Metric Top Connection Bottom Connection Weight Maximum Flow Rate Maximum Torque Maximum Power Maximum Weight Dynamic on bit Static Maximum Allowable Pull Pull to Yield Motor AS PER REQUEST 3 1/2 Reg 3 1/2 Reg 1,164 3 3,5 83 43, 118, 118, 2, gpm ft- hp 516 1.14 4,75 62 19, 52, 52, 9, m 3 /min N-m kw Bend Settings (degrees).26.52.78 1.3 1.27 1.5 1.72 1.93 2.12 2.3 2.6 2.82 2.95 3. Build Rate (degrees/1ft(3 m)) Hole Sizes (in, ) 5 7/8 6 1/8 6 1/4 149 156 159 6 3/4 171.47.46.93. 2.7 1.76 1.3.58 4.93 3.99 3.53 1.65 7.7 6.14 5.67 3.8 9.13 8.19 7.73 5.86 11.1 1.17 9.7 7.83 12.99 12.2 11.59 9.71 14.79 13.86 13.39 11.52 16.42 15.49 15.2 13.15 17.97 17.3 16.56 14.69 2.54 19.31 19.14 17.27 22.43 21.5 21.3 19.16 23.55 22.61 22.15 2.27 23.98 23.4 22.58 2.7 66

4 3/4 (121 ) 7-8 4.5 SX Stage Maximum Pump Rate 3 gpm 1,14 Lpm Revolutions per unit volume.463 rev/gal. 122 rev/l Pressure at full Load 68 psi 4,688 kpa Torque at full load 3,5 ft 4,745 N m 15 125 1 75 5 25 IMPERIAL PERFORMANCE CURVES 275 225 15 3 2 4 6 8 DIFFERENTIAL PRESSURE (psi) 4 3 2 1 TORQUE (ft ) Drilling Fluid Flow (GPM) 15 225 275 3 (off-bottom pressure) (PSI) 62 72 17 133 (on-bottom minus off-bottom pressure) 618 68 573 547 16 METRIC PERFORMANCE CURVES 5 12 8 4 568 852 1136 141 1 2 3 4 5 DIFFERENTIAL PRESSURE (kpa) 4 3 2 1 TORQUE (N m) Drilling Fluid Flow (L/min) 568 852 141 1136 (off-bottom pressure) (kpa) 427 496 738 917 (on-bottom minus off-bottom pressure) 4261 4192 3951 3771 67

4 3/4 (121 ) 7-8 4.5 SX HR Stage A. Distance to stabilizer B. Box to Bend C. Overall Length D. Thread Prot. Diameter E. Kick Pad Diameter 18 62 5.38 5.25 Imperial 457 1,575 358 911 137 133 Metric Top Connection Bottom Connection Weight Maximum Flow Rate Maximum Torque Maximum Power Maximum Weight Dynamic on bit Static Maximum Allowable Pull Pull to Yield Motor AS PER REQUEST 3 1/2 Reg 3 1/2 Reg 1,164 3 5,25 132 43, 118, 118, 2, gpm ft- hp 516 1.14 7,12 98 19, 52, 52, 9, m 3 /min N-m kw Bend Settings (degrees).26.52.78 1.3 1.27 1.5 1.72 1.93 2.12 2.3 2.6 2.82 2.95 3. Build Rate (degrees/1ft(3 m)) Hole Sizes (in, ) 5 7/8 6 1/8 6 1/4 149 156 159 6 3/4 171.47.46.93. 2.7 1.76 1.3.58 4.93 3.99 3.53 1.65 7.7 6.14 5.67 3.8 9.13 8.19 7.73 5.86 11.1 1.17 9.7 7.83 12.99 12.2 11.59 9.71 14.79 13.86 13.39 11.52 16.42 15.49 15.2 13.15 17.97 17.3 16.56 14.69 2.54 19.31 19.14 17.27 22.43 21.5 21.3 19.16 23.55 22.61 22.15 2.27 23.98 23.4 22.58 2.7 68

4 3/4 (121 ) 7-8 4.5 SX HR Stage Maximum Pump Rate 3 gpm 1,136 Lpm Revolutions per unit volume.463 rev/gal.65 rev/l Pressure at full Load 1,1 psi 6,964 kpa Torque at full load 5,25 ft 7,118 N m 15 125 1 75 5 25 IMPERIAL PERFORMANCE CURVES 3 275 225 15 5 1 DIFFERENTIAL PRESSURE (psi) 6 5 4 3 2 1 TORQUE (ft ) Drilling Fluid Flow (GPM) 15 225 275 3 (off-bottom pressure) (PSI) 76 15 12 14 (on-bottom minus off-bottom pressure) 934 95 89 87 16 METRIC PERFORMANCE CURVES 8 12 8 4 1136 141 852 568 2 4 6 8 DIFFERENTIAL PRESSURE (kpa) 6 4 2 TORQUE (N m) Drilling Fluid Flow (L/min) 568 852 141 1136 (off-bottom pressure) (kpa) 524 724 827 965 (on-bottom minus off-bottom pressure) 644 624 6136 5998 69

5 (127 ) Mud Motors

5 (127 ) 6-7 6. Stage A. Distance to stabilizer B. Box to Bend C. Overall Length D. Thread Prot. Diameter E. Kick Pad Diameter 19 6 5.38 5.25 Imperial 483 1,524 29 7,366 137 133 Metric Top Connection Bottom Connection Weight Maximum Flow Rate Maximum Torque Maximum Power Maximum Weight Dynamic on bit Static Maximum Allowable Pull Pull to Yield Motor AS PER REQUEST 3 1/2 Reg 3 1/2 Reg 1,144 36 2,736 221 43, 118, 118, 2, gpm ft- hp 59 1.36 3,71 165 19, 52, 52, 9, m 3 /min N-m kw Bend Settings (degrees).26.52.78 1.3 1.27 1.5 1.72 1.93 2.12 2.3 2.6 2.82 2.95 3. Build Rate (degrees/1ft(3 m)) Hole Sizes (in, ) 6 1/8 6 1/4 156 159.76. 1.49 1.2 3.74 3.27 5.9 5.43 7.98 7.5 9.97 9.49 11.87 11.4 13.68 13.21 15.33 14.86 16.89 16.42 19.49 19.2 21.38 2.92 22.52 22.5 22.96 22.48 72

5 (127 ) 6-7 6. Stage Maximum Pump Rate 35 gpm 1,363 Lpm Revolutions per unit volume.817 rev/gal.216 rev/l Pressure at full Load 1,47 psi 7,219 kpa Torque at full load 2,736 ft 3,71 N m 35 IMPERIAL PERFORMANCE CURVES 3 3 25 2 15 1 5 15 Torque 2 3 35 25 5 75 1 125 DIFFERENTIAL PRESSURE (psi) 25 2 15 1 5 TORQUE (ft ) Drilling Fluid Flow (GPM) 15 2 3 35 (off-bottom pressure) (PSI) 71 95 161 25 (on-bottom - off-bottom pressure) (PSI) 979 955 889 845 35 3 25 2 15 1 5 METRIC PERFORMANCE CURVES Torque 568 757 1136 1363 2 4 6 8 DIFFERENTIAL PRESSURE (kpa) 4 35 3 25 2 15 1 5 TORQUE (N m) Drilling Fluid Flow (L/min) 568 757 1136 1325 (off-bottom pressure) (kpa) 49 655 111 1413 (on-bottom - off-bottom pressure) (kpa) 675 6584 6129 5826 73

5 (127 ) 6-7 7. Stage A. Distance to stabilizer B. Box to Bend C. Overall Length D. Thread Prot. Diameter E. Kick Pad Diameter 19 6 5.38 5.25 Imperial 483 1,524 324 8,23 137 133 Metric Top Connection Bottom Connection Weight Maximum Flow Rate Maximum Torque Maximum Power Maximum Weight Dynamic on bit Static Maximum Allowable Pull Pull to Yield Motor AS PER REQUEST 3 1/2 Reg 3 1/2 Reg 1,182 36 3,265 257 43, 118, 118, 2, gpm ft- hp 526 1.36 4,427 192 19, 52, 52, 9, m 3 /min N-m kw Bend Settings (degrees).26.52.78 1.3 1.27 1.5 1.72 1.93 2.12 2.3 2.6 2.82 2.95 3. Build Rate (degrees/1ft(3 m)) Hole Sizes (in, ) 6 1/8 6 1/4 156 159.67. 1.15.77 2.98 2.6 4.73 4.35 6.41 6.3 8.3 7.65 9.57 9.19 11.4 1.66 12.38 12. 13.64 13.26 15.75 15.37 17.29 16.91 18.21 17.82 18.56 18.18 74

5 (127 ) 6-7 7. Stage Maximum Pump Rate 36 gpm 1,363 Lpm Revolutions per unit volume.817 rev/gal.216 rev/l Pressure at full Load 1,225 psi 8,446 kpa Torque at full load 3,262 ft 4, 427 N m 35 IMPERIAL PERFORMANCE CURVES 35 3 25 2 15 1 5 Torque 15 2 3 36 5 1 15 DIFFERENTIAL PRESSURE (psi) 3 25 2 15 1 5 TORQUE (ft ) Drilling Fluid Flow (GPM) 15 2 3 36 (off-bottom pressure) (PSI) 12 138 17 25 (on-bottom - off-bottom pressure) (PSI) 1123 187 155 12 35 METRIC PERFORMANCE CURVES 5 3 25 2 15 1 5 757 568 Torque 1136 1363 2 4 6 8 1 DIFFERENTIAL PRESSURE (kpa) 4 3 2 1 TORQUE (N m) Drilling Fluid Flow (L/min) 568 757 1136 1363 (off-bottom pressure) (kpa) 73 951 1172 1413 (on-bottom - off-bottom pressure) (kpa) 7743 7495 7274 733 75

6 1/4 (159 ) Mud Motors

6 1/4 (159 ) 7-8 4.8 Stage A. Distance to stabilizer B. Box to Bend C. Overall Length D. Thread Prot. Diameter E. Kick Pad Diameter 19 76 7.32 7. Imperial 483 1,93 353 8,966 186 178 Metric Top Connection Bottom Connection Weight Maximum Flow Rate Maximum Torque Maximum Power Maximum Weight Dynamic on bit Static Maximum Allowable Pull Pull to Yield Motor AS PER REQUEST 4 1/2 Reg 4 1/2 Reg 2,81 4 5,74 129 87,3 247, 218,5 475, gpm ft- hp 926 1.51 7,79 96 38,8 19, 97, 212, m 3 /min N-m kw Bend Settings (degrees).26.52.78 1.3 1.27 1.5 1.72 1.93 2.12 2.3 2.6 2.82 2.95 3. Build Rate (degrees/1ft(3 m)) Hole Sizes (in, ) 7 7/8 8 1/2 8 3/4 2 216 223 9 7/8 251.4... 2.11.12.68. 4.18 2.19 1.39. 6.17 4.18 3.38.2 8.8 6.9 5.29 1.71 9.91 7.92 7.12 3.54 11.6 9.67 8.87 5.29 13.33 11.31 1.55 6.96 14.85 12.85 12.6 8.48 16.28 14.29 13.49 9.91 18.67 16.68 15.88 12.3 2.43 18.43 17.64 14.5 21.46 19.46 18.67 15.9 21.86 19.87 19.7 15.49 78

6 1/4 (159 ) 7-8 4.8 Stage Maximum Pump Rate 4 gpm 1,51 Lpm Revolutions per unit volume.33 rev/gal.87 rev/l Pressure at full Load 72 psi 4,96 kpa Torque at full load 5,74 ft 7,79 N m 14 IMPERIAL PERFORMANCE CURVES 7 12 1 8 6 4 2 15 Torque 2 3 4 2 4 6 8 DIFFERENTIAL PRESSURE (psi) 6 5 4 3 2 1 TORQUE (ft ) Drilling Fluid Flow (GPM) 15 2 3 4 (off-bottom pressure) (PSI) 46 63 88 121 (on-bottom - off-bottom pressure) (PSI) 674 657 632 599 14 12 1 8 6 4 2 568 Torque METRIC PERFORMANCE CURVES 757 1136 1514 1 2 3 4 5 6 DIFFERENTIAL PRESSURE (kpa) 8 6 4 2 TORQUE (N m) Drilling Fluid Flow (L/min) 568 757 1136 1514 (off-bottom pressure) (kpa) 317 434 67 834 (on-bottom - off-bottom pressure) (kpa) 4647 453 4357 413 79

6 1/2 (165 ) Mud Motors

6 1/2 (165 ) 4-5 4.8 Stage A. Distance to stabilizer B. Box to Bend C. Overall Length D. Thread Prot. Diameter E. Kick Pad Diameter 22 76 7.19 7. Imperial 559 1,93 34 7,722 183 178 Metric Top Connection Bottom Connection Weight Maximum Flow Rate Maximum Torque Maximum Power Maximum Weight Dynamic on bit Static Maximum Allowable Pull Pull to Yield Motor AS PER REQUEST 4 1/2 Reg 4 1/2 Reg 1,911 6 2,725 236 87,3 247, 218,5 475, gpm ft- hp 85 2.27 3,695 176 38,8 19, 97, 212, m 3 /min N-m kw Bend Settings (degrees).26.52.78 1.3 1.27 1.5 1.72 1.93 2.12 2.3 2.6 2.82 2.95 3. Build Rate (degrees/1ft(3 m)) Hole Sizes (in, ) 7 7/8 8 1/2 8 3/4 2 216 223 9 7/8 251.9... 2.38..95. 4.85 2.47 1.52. 7.23 4.85 3.89.39 9.51 7.13 6.18 1.89 11.7 9.31 8.36 4.8 13.79 11.41 1.46 6.17 15.79 13.41 12.45 8.17 17.6 15.21 14.26 9.98 19.31 16.93 15.97 11.69 22.17 19.78 18.83 14.54 24.26 21.88 2.93 16.64 25.5 23.12 22.17 17.88 25.98 23.6 22.64 18.35 82

6 1/2 (165 ) 4-5 4.8 Stage Maximum Pump Rate 6 gpm 2,271 Lpm Revolutions per unit volume.423 rev/gal.112 rev/l Pressure at full Load 674 psi 4,647 kpa Torque at full load 2,725 ft 3,695 N m 3 IMPERIAL PERFORMANCE CURVES 3 25 2 15 1 5 3 Torque 4 5 6 2 4 6 8 DIFFERENTIAL PRESSURE (psi) 25 2 15 1 5 TORQUE (ft ) Drilling Fluid Flow (GPM) 3 4 5 6 (off-bottom pressure) (PSI) 45 56 69 86 (on-bottom - off-bottom pressure) (PSI) 629 618 65 588 3 25 2 15 1 5 METRIC PERFORMANCE CURVES 1136 Torque 1514 1893 2271 1 2 3 4 5 DIFFERENTIAL PRESSURE (kpa) 4 35 3 25 2 15 1 5 TORQUE (N m) Drilling Fluid Flow (L/min) 1136 1514 1893 2271 (off-bottom pressure) (kpa) 31 386 476 593 (on-bottom - off-bottom pressure) (kpa) 4337 4261 4171 454 83

6 1/2 (165 ) 6-7 3.1 Stage ERT A. Distance to stabilizer B. Box to Bend C. Overall Length D. Thread Prot. Diameter E. Kick Pad Diameter 22 76 7.19 7. Imperial 559 1,93 278 7,54 183 178 Metric Top Connection Bottom Connection Weight Maximum Flow Rate Maximum Torque Maximum Power Maximum Weight Dynamic on bit Static Maximum Allowable Pull Pull to Yield Motor AS PER REQUEST 4 1/2 Reg 4 1/2 Reg 1,884 65 8,235 27 87,3 247, 218,5 475, gpm ft- hp 838 2.46 11,165 21 38,8 19, 97, 212, m 3 /min N-m kw Bend Settings (degrees).26.52.78 1.3 1.27 1.5 1.72 1.93 2.12 2.3 2.6 2.82 2.95 3. Build Rate (degrees/1ft(3 m)) Hole Sizes (in, ) 7 7/8 8 1/2 8 3/4 2 216 223 9 7/8 251.3... 2.78.13.93. 5.52 2.88 1.82. 8.16 5.51 4.46.31 1.7 8.5 6.99 2.23 13.12 1.48 9.42 4.66 15.45 12.8 11.74 6.98 17.67 15.2 13.96 9.2 19.68 17.3 15.97 11.2 21.58 18.93 17.87 13.11 24.76 22.11 21.5 16.28 27.9 24.43 23.37 18.6 28.46 25.81 24.75 19.98 28.99 26.34 25.28 2.51 84

6 1/2 (165 ) 6-7 3.1 Stage ERT Maximum Pump Rate 65 gpm 2,461 Lpm Revolutions per unit volume.37 rev/gal.98 rev/l Pressure at full Load 1,175 psi 8,95 kpa Torque at full load 8,235 ft 11,165 N-m 3 IMPERIAL PERFORMANCE CURVES 1 25 2 15 1 5 3 Torque 4 5 65 5 1 15 DIFFERENTIAL PRESSURE (psi) 8 6 4 2 TORQUE (ft ) Drilling Fluid Flow (GPM) 3 4 5 65 (off-bottom pressure) (PSI) 9 13 16 2 (on-bottom - off-bottom pressure) (PSI) 116 112 19 15 3 METRIC PERFORMANCE CURVES 14 25 12 2461 2 1 1893 8 15 1514 6 1 1136 4 5 2 2 4 6 8 1 Torque DIFFERENTIAL PRESSURE (kpa) TORQUE (N m) Drilling Fluid Flow (L/min) 1136 1514 1893 2461 (off-bottom pressure) (kpa) 621 896 113 1379 (on-bottom -- off-bottom pressure) (kpa) 7998 7722 7515 7239 85

6 1/2 (165 ) 6-7 5. Stage A. Distance to stabilizer B. Box to Bend C. Overall Length D. Thread Prot. Diameter E. Kick Pad Diameter 22 76 7.19 7. Imperial 559 1,93 35 8,89 183 178 Metric Top Connection Bottom Connection Weight Maximum Flow Rate Maximum Torque Maximum Power Maximum Weight Dynamic on bit Static Maximum Allowable Pull Pull to Yield Motor AS PER REQUEST 4 1/2 Reg 4 1/2 Reg 2,87 6 6,23 177 87,3 247, 218,5 475, gpm ft- hp 928 2.27 8,45 132 38,8 19, 97, 212, m 3 /min N-m kw Bend Settings (degrees).26.52.78 1.3 1.27 1.5 1.72 1.93 2.12 2.3 2.6 2.82 2.95 3. Build Rate (degrees/1ft(3 m)) Hole Sizes (in, ) 7 7/8 8 1/2 8 3/4 2 216 223 9 7/8 251.21... 1.88.13.93. 3.96 1.96 1.15. 5.97 3.96 3.16.45 7.89 5.89 5.8 1.47 9.74 7.73 6.93 3.32 11.5 9.5 8.7 5.8 13.19 11.18 1.38 6.77 14.72 12.71 11.91 8.3 16.16 14.16 13.35 9.74 18.57 16.57 15.76 12.15 2.34 18.33 17.53 13.92 21.39 19.38 18.58 14.96 21.79 19.78 18.98 15.36 86

6 1/2 (165 ) 6-7 5. Stage Maximum Pump Rate 6 gpm 2,27 Lpm Revolutions per unit volume.292 rev/gal.77 rev/l Pressure at full Load 75 psi 5,17 kpa Torque at full load 6,23 ft 8,45 N m 2 175 15 125 1 75 5 25 IMPERIAL PERFORMANCE CURVES 6 5 4 3 3 6 9 DIFFERENTIAL PRESSURE (psi) 9 6 3 TORQUE (ft ) Drilling Fluid Flow (GPM) 3 4 5 6 (off-bottom pressure) (PSI) 69 81 17 119 (on-bottom minus off-bottom pressure) (PSI) 681 669 643 631 2 METRIC PERFORMANCE CURVES 15 16 12 8 4 2271 1893 1514 1136 25 5 DIFFERENTIAL PRESSURE (kpa) 7 35 TORQUE (N m) Drilling Fluid Flow (L/min) 1136 1514 1893 2271 (off-bottom pressure) (kpa) 476 558 738 82 (on-bottom minus off-bottom pressure) (kpa) 4695 4613 4433 4351 87

6 1/2 (165 ) 6-7 5. Stage HR A. Distance to stabilizer B. Box to Bend C. Overall Length D. Thread Prot. Diameter E. Kick Pad Diameter 22 76 7.19 7. Imperial 559 1,93 35 8,89 183 178 Metric Top Connection Bottom Connection Weight Maximum Flow Rate Maximum Torque Maximum Power Maximum Weight Dynamic on bit Static Maximum Allowable Pull Pull to Yield Motor AS PER REQUEST 4 1/2 Reg 4 1/2 Reg 2,87 6 9,35 29 87,3 247, 218,5 475, gpm ft- hp 928 2.27 12,68 216 38,8 19, 97, 212, m 3 /min N-m kw Bend Settings (degrees).26.52.78 1.3 1.27 1.5 1.72 1.93 2.12 2.3 2.6 2.82 2.95 3. Build Rate (degrees/1ft(3 m)) Hole Sizes (in, ) 7 7/8 8 1/2 8 3/4 2 216 223 9 7/8 251.21... 1.88.13.93. 3.96 1.96 1.15. 5.97 3.96 3.16.45 7.89 5.89 5.8 1.47 9.74 7.73 6.93 3.32 11.5 9.5 8.7 5.8 13.19 11.18 1.38 6.77 14.72 12.71 11.91 8.3 16.16 14.16 13.35 9.74 18.57 16.57 15.76 12.15 2.34 18.33 17.53 13.92 21.39 19.38 18.58 14.96 21.79 19.78 18.98 15.36 88

6 1/2 (165 ) 6-7 5. Stage HR Maximum Pump Rate 6 gpm 2,27 Lpm Revolutions per unit volume.292 rev/gal.77 rev/l Pressure at full Load 1,13 psi 7,76 kpa Torque at full load 9,35 ft 12,68 N m 2 175 15 125 1 75 5 25 IMPERIAL PERFORMANCE CURVES 6 5 4 3 3 6 9 12 DIFFERENTIAL PRESSURE (psi) 12 9 6 3 TORQUE (ft ) Drilling Fluid Flow (GPM) 3 4 5 6 (off-bottom pressure) (PSI) 149 167 182 199 (on-bottom minus off-bottom pressure) (PSI) 981 963 948 931 2 16 12 8 4 METRIC PERFORMANCE CURVES 2271 1893 1514 1136 25 5 75 DIFFERENTIAL PRESSURE (kpa) 14 15 7 35 TORQUE (N m) Drilling Fluid Flow (L/min) 1136 1514 1893 2271 (off-bottom pressure) (kpa) 127 1151 1255 1372 (on-bottom minus off-bottom pressure) (kpa) 6764 664 6536 6419 89

6 1/2 (165 ) 7-8 2.9 Stage Slow A. Distance to stabilizer B. Box to Bend C. Overall Length D. Thread Prot. Diameter E. Kick Pad Diameter 22 76 7.19 7. Imperial 559 1,93 37 9,39 183 178 Metric Top Connection Bottom Connection Weight Maximum Flow Rate Maximum Torque Maximum Power Maximum Weight Dynamic on bit Static Maximum Allowable Pull Pull to Yield Motor AS PER REQUEST 4 1/2 Reg 4 1/2 Reg 2,442 5 7,42 163 87,3 247, 218,5 475, gpm ft- hp 1,86 1.89 1,36 122 38,8 19, 97, 212, m 3 /min N-m kw Bend Settings (degrees).26.52.78 1.3 1.27 1.5 1.72 1.93 2.12 2.3 2.6 2.82 2.95 3. Build Rate (degrees/1ft(3 m)) Hole Sizes (in, ) 7 7/8 8 1/2 8 3/4 2 216 223 9 7/8 251.23... 1.73.16.91. 3.69 1.8 1.5. 5.57 3.69 2.93.46 7.38 5.5 4.74 1.35 9.12 7.23 6.48 3.8 1.77 8.89 8.14 4.74 12.36 1.47 9.72 6.33 13.79 11.91 11.15 7.76 15.15 13.27 12.51 9.12 17.42 15.53 14.78 11.38 19.8 17.19 16.44 13.4 2.6 18.18 17.42 14.3 2.44 18.55 17.8 14.4 9

6 1/2 (165 ) 7-8 2.9 Stage Slow Maximum Pump Rate 5 gpm 1,893 Lpm Revolutions per unit volume.144 rev/gal.38 rev/l Pressure at full Load 56 psi 3,861 kpa Torque at full load 7,42 ft 1,36 N m 8 7 6 5 4 3 2 1 Torque IMPERIAL PERFORMANCE CURVES 2 3 4 5 1 2 3 4 5 6 DIFFERENTIAL PRESSURE (psi) 8 7 6 5 4 3 2 1 TORQUE (ft ) Drilling Fluid Flow (GPM) 2 3 4 5 (off-bottom pressure) (PSI) 44 17 153 21 (on-bottom - off-bottom pressure) (PSI) 516 453 47 35 8 METRIC PERFORMANCE CURVES 7 1 2271 6 8 5 1893 4 1514 6 3 757 4 2 1 2 1 2 3 4 Torque DIFFERENTIAL PRESSURE (kpa) TORQUE (N m) Drilling Fluid Flow (L/min) 757 1136 1514 1893 (off-bottom pressure) (kpa) 33 738 155 1448 (on-bottom - off-bottom pressure) (kpa) 3558 3123 286 2413 91

6 1/2 (165 ) 7-8 3. Stage A. Distance to stabilizer B. Box to Bend C. Overall Length D. Thread Prot. Diameter E. Kick Pad Diameter 22 76 7.19 7. Imperial 559 1,93 275 6,985 183 178 Metric Top Connection Bottom Connection Weight Maximum Flow Rate Maximum Torque Maximum Power Maximum Weight Dynamic on bit Static Maximum Allowable Pull Pull to Yield Motor AS PER REQUEST 4 1/2 Reg 4 1/2 Reg 1,835 6 4,19 12 87,3 247, 218,5 475, gpm ft- hp 816 2.27 5,67 76 38,8 19, 97, 212, m 3 /min N-m kw Bend Settings (degrees).26.52.78 1.3 1.27 1.5 1.72 1.93 2.12 2.3 2.6 2.82 2.95 3. Build Rate (degrees/1ft(3 m)) Hole Sizes (in, ) 7 7/8 8 1/2 8 3/4 2 216 223 9 7/8 251.2... 2.73.12.93. 5.45 2.83 1.78. 8.6 5.44 4.4.32 1.57 7.95 6.9 2.19 12.97 1.3 9.31 4.59 15.27 12.65 11.61 6.89 17.47 14.85 13.8 9.9 19.46 16.84 15.79 11.7 21.34 18.72 17.68 12.96 24.48 21.86 2.81 16.9 26.79 24.17 23.12 18.4 28.15 25.53 24.48 19.76 28.68 26.5 25. 2.28 92

6 1/2 (165 ) 7-8 3. Stage Maximum Pump Rate 6 gpm 2,271 Lpm Revolutions per unit volume.283 rev/gal.75 rev/l Pressure at full Load 45 psi 3,13 kpa Torque at full load 4,19 ft 5,67 N m IMPERIAL PERFORMANCE CURVES 18 16 6 4 14 5 12 3 4 1 8 3 2 6 4 1 2 1 2 3 4 5 Torque DIFFERENTIAL PRESSURE (psi) TORQUE (ft ) Drilling Fluid Flow (GPM) 3 4 5 6 (off-bottom pressure) (PSI) 38 68 16 152 (on-bottom - off-bottom pressure) (PSI) 412 382 344 298 18 16 14 12 1 8 6 4 2 METRIC PERFORMANCE CURVES 1136 Torque 1514 1893 2271 1 2 3 DIFFERENTIAL PRESSURE (kpa) 6 5 4 3 2 1 TORQUE (N m) Drilling Fluid Flow (L/min) 1136 1514 1893 2271 (off-bottom pressure) (kpa) 262 469 731 148 (on-bottom - off-bottom pressure) (kpa) 2841 2634 2372 255 93

6 1/2 (165 ) 7-8 3. Stage Slow A. Distance to stabilizer B. Box to Bend C. Overall Length D. Thread Prot. Diameter E. Kick Pad Diameter 22 76 7.19 7. Imperial 559 1,93 348 8,839 183 178 Metric Top Connection Bottom Connection Weight Maximum Flow Rate Maximum Torque Maximum Power Maximum Weight Dynamic on bit Static Maximum Allowable Pull Pull to Yield Motor AS PER REQUEST 4 1/2 Reg 4 1/2 Reg 2,578 6 7,2 16 87,3 247, 218,5 475, gpm ft- hp 1,147 2.27 9,76 79 38,8 19, 97, 212, m 3 /min N-m kw Bend Settings (degrees).26.52.78 1.3 1.27 1.5 1.72 1.93 2.12 2.3 2.6 2.82 2.95 3. Build Rate (degrees/1ft(3 m)) Hole Sizes (in, ) 7 7/8 8 1/2 8 3/4 2 216 223 9 7/8 251.2... 2.73.12.93. 5.45 2.83 1.78. 8.6 5.44 4.4.32 1.57 7.95 6.9 2.19 12.97 1.3 9.31 4.59 15.27 12.65 11.61 6.89 17.47 14.85 13.8 9.9 19.46 16.84 15.79 11.7 21.34 18.72 17.68 12.96 24.48 21.86 2.81 16.9 26.79 24.17 23.12 18.4 28.15 25.53 24.48 19.76 28.68 26.5 25. 2.28 94

6 1/2 (165 ) 7-8 3. Stage Slow Maximum Pump Rate 6 gpm 2,27 Lpm Revolutions per unit volume.155 rev/gal.41 rev/l Pressure at full Load 45 psi 3,1 kpa Torque at full load 7,2 ft 9,76 N m 1 8 6 4 2 IMPERIAL PERFORMANCE CURVES 6 5 4 3 1 2 3 4 5 DIFFERENTIAL PRESSURE (psi) 12 1 8 6 4 2 TORQUE (ft ) Drilling Fluid Flow (GPM) 3 4 5 6 (off-bottom pressure) (PSI) 38 5 63 75 (on-bottom minus off-bottom pressure) (PSI) 413 4 388 375 1 8 6 4 2 METRIC PERFORMANCE CURVES 2271 1893 1514 1136 1 2 3 DIFFERENTIAL PRESSURE (kpa) 14 12 1 8 6 4 2 TORQUE (N m) Drilling Fluid Flow (L/min) 1136 1514 1893 2271 (off-bottom pressure) (kpa) 259 345 431 517 (on-bottom minus off-bottom pressure) (kpa) 2844 2758 2672 2586 95

6 1/2 (165 ) 7-8 5. Stage A. Distance to stabilizer B. Box to Bend C. Overall Length D. Thread Prot. Diameter E. Kick Pad Diameter 22 76 7.19 7. Imperial 559 1,93 34 8,636 183 178 Metric Top Connection Bottom Connection Weight Maximum Flow Rate Maximum Torque Maximum Power Maximum Weight Dynamic on bit Static Maximum Allowable Pull Pull to Yield Motor AS PER REQUEST 4 1/2 Reg 4 1/2 Reg 2,31 6 6,98 19 87,3 247, 218,5 475, gpm ft- hp 1,28 2.27 9,46 142 38,8 19, 97, 212, m 3 /min N-m kw Bend Settings (degrees).26.52.78 1.3 1.27 1.5 1.72 1.93 2.12 2.3 2.6 2.82 2.95 3. Build Rate (degrees/1ft(3 m)) Hole Sizes (in, ) 7 7/8 8 1/2 8 3/4 2 216 223 9 7/8 251.21... 1.88.13.93. 3.96 1.96 1.15. 5.97 3.96 3.16.45 7.89 5.89 5.8 1.47 9.74 7.73 6.93 3.32 11.5 9.5 8.7 5.8 13.19 11.18 1.38 6.77 14.72 12.71 11.91 8.3 16.16 14.16 13.35 9.74 18.57 16.57 15.76 12.15 2.34 18.33 17.53 13.92 21.39 19.38 18.58 14.96 21.79 19.78 18.98 15.36 96

6 1/2 (165 ) 7-8 5. Stage Maximum Pump Rate 6 gpm 2,271 Lpm Revolutions per unit volume.28 rev/gal.76 rev/l Pressure at full Load 75 psi 5,17 kpa Torque at full load 6,98 ft 9,46 N m 2 IMPERIAL PERFORMANCE CURVES 9 16 12 8 4 5 4 3 6 6 3 TORQUE (ft ) 5 DIFFERENTIAL PRESSURE (psi) Drilling Fluid Flow (GPM) 3 4 5 6 (off-bottom pressure) (PSI) 69 81 17 119 (on-bottom minus off-bottom pressure) (PSI) 681 673 643 631 2 METRIC PERFORMANCE CURVES 12 15 1 5 1136 1514 1893 2271 8 4 TORQUE (N m) 25 5 DIFFERENTIAL PRESSURE (kpa) Drilling Fluid Flow (L/min) 1136 1514 1893 2271 (off-bottom pressure) (kpa) 476 558 738 82 (on-bottom minus off-bottom pressure) (kpa) 4695 464 4433 4351 97

6 1/2 (165 ) 7-8 5. Stage HR A. Distance to stabilizer B. Box to Bend C. Overall Length D. Thread Prot. Diameter E. Kick Pad Diameter 22 76 7.19 7. Imperial 559 1,93 354 8,992 183 178 Metric Top Connection Bottom Connection Weight Maximum Flow Rate Maximum Torque Maximum Power Maximum Weight Dynamic on bit Static Maximum Allowable Pull Pull to Yield Motor AS PER REQUEST 4 1/2 Reg 4 1/2 Reg 2,176 6 1,46 323 87,3 247, 218,5 475, gpm ft- hp 968 2.3 14,19 241 38,8 19, 97, 212, m 3 /min N-m kw Bend Settings (degrees).26.52.78 1.3 1.27 1.5 1.72 1.93 2.12 2.3 2.6 2.82 2.95 3. Build Rate (degrees/1ft(3 m)) Hole Sizes (in, ) 7 7/8 8 1/2 8 3/4 2 216 223 9 7/8 251.....2... 1.93.12.94. 4.6 2.1 1.19. 6.1 4.6 3.24.45 8.7 6.2 5.2 1.52 9.95 7.9 7.9 3.4 11.75 9.71 8.89 5.2 13.47 11.43 1.6 16.92 16.51 14.46 13.64 9.95 18.97 16.92 16.1 12.41 2.77 18.72 17.9 14.22 21.84 19.79 18.97 15.28 22.25 2.2 19.38 15.69 98

6 1/2 (165 ) 7-8 5. Stage HR Maximum Pump Rate 6 gpm 2271 Lpm Revolutions per unit volume.288 rev/gal.76 rev/l Pressure at full Load 1,13 psi 7,76 kpa Torque at full load 1,46 ft 14,19 N m 2 175 15 125 1 75 5 25 IMPERIAL PERFORMANCE CURVES 3 Torque 4 5 6 2 4 6 8 1 12 DIFFERENTIAL PRESSURE (psi) 12 9 6 3 TORQUE (ft ) Drilling Fluid Flow (GPM) 3 4 5 6 (off-bottom pressure) (PSI) 79 91 117 129 (on-bottom minus off-bottom pressure) (PSI) 151 139 113 11 2 18 16 14 12 1 8 6 4 2 METRIC PERFORMANCE CURVES 1514 1136 Torque 1893 2271 25 5 75 DIFFERENTIAL PRESSURE (kpa) 16 14 12 1 8 6 4 2 TORQUE (N m) Drilling Fluid Flow (L/min) 1136 1514 1893 2271 (off-bottom pressure) (kpa) 545 627 87 889 (on-bottom minus off-bottom pressure) (kpa) 7246 7164 6984 692 99

6 1/2 (165 ) 7-8 5.7 Stage A. Distance to stabilizer B. Box to Bend C. Overall Length D. Thread Prot. Diameter E. Kick Pad Diameter 22 76 7.19 7. Imperial 559 1,93 41 5,766 183 178 Metric Top Connection Bottom Connection Weight Maximum Flow Rate Maximum Torque Maximum Power Maximum Weight Dynamic on bit Static Maximum Allowable Pull Pull to Yield Motor AS PER REQUEST 4 1/2 Reg 4 1/2 Reg 2,326 6 9,15 222 87,3 247, 218,5 475, gpm ft- hp 1,35 2.3 12,4 166 38,8 19, 97, 212, m 3 /min N-m kw Bend Settings (degrees).26.52.78 1.3 1.27 1.5 1.72 1.93 2.12 2.3 2.6 2.82 2.95 3. Build Rate (degrees/1ft(3 m)) Hole Sizes (in, ) 7 7/8 8 1/2 8 3/4 2 216 223 9 7/8 251.26... 1.48.19.86. 3.23 1.55.88. 4.9 3.23 2.56.46 6.51 4.84 4.17 1.15 8.5 6.38 5.1 2.69 9.53 7.85 7.19 4.17 1.94 9.26 8.59 5.58 12.22 1.54 9.87 6.85 13.42 11.75 11.8 8.6 15.44 13.76 13.9 1.8 16.92 15.24 14.57 11.55 17.79 15.98 15.31 12.29 18.13 16.45 15.78 12.76 1

6 1/2 (165 ) 7-8 5.7 Stage Maximum Pump Rate 6 gpm 2271 Lpm Revolutions per unit volume.242 rev/gal.64 rev/l Pressure at full Load 86 psi 5,9 kpa Torque at full load 9,15 ft 12,4 N m 16 IMPERIAL PERFORMANCE CURVES 15 14 6 9 12 5 75 1 4 6 8 6 3 45 4 3 2 15 2 4 6 8 1 Torque DIFFERENTIAL PRESSURE (psi) TORQUE (ft ) Drilling Fluid Flow (GPM) 3 4 5 6 51 76 87 15 (off-bottom pressure) (PSI) (on-bottom minus off-bottom pressure) (PSI) 89 784 773 755 16 METRIC PERFORMANCE CURVES 14 14 12 1 8 6 4 2 Torque 1136 1514 1893 2271 2 4 6 DIFFERENTIAL PRESSURE (kpa) 12 1 8 6 4 2 TORQUE (N m) Drilling Fluid Flow (L/min) 1136 1514 1893 2271 352 524 6 724 (off-bottom pressure) (kpa) (on-bottom minus off-bottom pressure) (kpa) 5578 545 533 526 11

6 1/2 (165 ) 7-8 5.7 Stage HR A. Distance to stabilizer B. Box to Bend C. Overall Length D. Thread Prot. Diameter E. Kick Pad Diameter 22 76 7.19 7. Imperial 559 1,93 41 1,414 183 178 Metric Top Connection Bottom Connection Weight Maximum Flow Rate Maximum Torque Maximum Power Maximum Weight Dynamic on bit Static Maximum Allowable Pull Pull to Yield Motor AS PER REQUEST 4 1/2 Reg 4 1/2 Reg 2,326 6 13,72 355 87,3 247, 218,5 475, gpm ft- hp 1,35 2.3 18,6 265 38,8 19, 97, 212, m 3 /min N-m kw Bend Settings (degrees).26.52.78 1.3 1.27 1.5 1.72 1.93 2.12 2.3 2.6 2.82 2.95 3. Build Rate (degrees/1ft(3 m)) Hole Sizes (in, ) 7 7/8 8 1/2 8 3/4 2 216 223 9 7/8 251.26... 1.48.19.86. 3.23 1.55.88. 4.9 3.23 2.56.46 6.51 4.84 4.17 1.15 8.5 6.38 5.1 2.69 9.53 7.85 7.19 4.17 1.94 9.26 8.59 5.58 12.22 1.54 9.87 6.85 13.42 11.75 11.8 8.6 15.44 13.76 13.9 1.8 16.92 15.24 14.57 11.55 17.79 15.98 15.31 12.29 18.13 16.45 15.78 12.76 12

6 1/2 (165 ) 7-8 5.7 Stage HR Maximum Pump Rate 6 gpm 2271 Lpm Revolutions per unit volume.242 rev/gal.64 rev/l Pressure at full Load 1,28 psi 8,84 kpa Torque at full load 13,72 ft 18,6 N m 16 14 12 1 8 6 4 2 IMPERIAL PERFORMANCE CURVES 6 5 4 3 5 1 15 DIFFERENTIAL PRESSURE (psi) 15 125 1 75 5 25 TORQUE (ft ) Drilling Fluid Flow (GPM) 3 4 5 6 (off-bottom pressure) (PSI) (on-bottom minus off-bottom pressure) (PSI) 151 176 187 25 1129 114 193 175 16 14 12 1 8 6 4 2 METRIC PERFORMANCE CURVES 2271 1893 1514 1136 5 1 DIFFERENTIAL PRESSURE (kpa) 2 175 15 125 1 75 5 25 TORQUE (N m) Drilling Fluid Flow (L/min) 1136 1514 1893 2271 (off-bottom pressure) (kpa) (on-bottom minus off-bottom pressure) (kpa) 141 1213 1289 1413 7784 7612 7536 7412 13

6 1/2 (165 ) 8-9 3. Stage A. Distance to stabilizer B. Box to Bend C. Overall Length D. Thread Prot. Diameter E. Kick Pad Diameter 22 76 7.19 7. Imperial 559 1,93 227 5,766 183 178 Metric Top Connection Bottom Connection Weight Maximum Flow Rate Maximum Torque Maximum Power Maximum Weight Dynamic on bit Static Maximum Allowable Pull Pull to Yield Motor AS PER REQUEST 4 1/2 Reg 4 1/2 Reg 425 5 96 49 87,3 247, 218,5 475, gpm ft- hp 189.61 1,32 37 38,8 19, 97, 212, m 3 /min N-m kw Bend Settings (degrees).26.52.78 1.3 1.27 1.5 1.72 1.93 2.12 2.3 2.6 2.82 2.95 3. Build Rate (degrees/1ft(3 m)) Hole Sizes (in, ) 7 7/8 8 1/2 8 3/4 2 216 223 9 7/8 251.1... 2.71.11.93. 5.41 2.81 1.77. 8.1 5.41 4.37.32 1.51 7.9 6.86 2.71 12.9 12.29 9.25 4.56 15.19 12.58 11.54 6.85 17.37 14.77 13.72 9.3 19.35 16.74 15.7 11.1 21.22 18.62 17.57 12.88 24.35 21.74 2.7 16. 26.64 24.6 22.99 18.3 28. 25.39 24.36 19.65 28.65 25.91 24.87 2.17 14

6 1/2 (165 ) 8-9 3. Stage Maximum Pump Rate 5 gpm 1,893 Lpm Revolutions per unit volume.34 rev/gal.9 rev/l Pressure at full Load 584 psi 4,27 kpa To rque at full load 4,9 ft 6,644 N m 2 IMPERIAL PERFORMANCE CURVES 6 16 5 5 12 8 4 2 3 4 4 3 2 1 TORQUE (ft ) 2 4 6 DIFFERENTIAL PRESSURE (psi) Drilling Fluid Flow (GPM) 2 3 4 5 (off-bottom pressure) (PSI) 49 85 136 2 (on-bottom minus off-bottom pressure) (PSI) 535 499 448 384 2 METRIC PERFORMANCE CURVES 75 16 1893 6 12 8 4 757 1514 1136 45 3 15 TORQUE (N m) 2 4 DIFFERENTIAL PRESSURE (kpa) Drilling Fluid Flow (L/min) 757 1136 1514 1893 (off-bottom pressure) (kpa) 338 586 938 1379 (on-bottom minus off-bottom pressure) (kpa) 3689 344 389 2648 15

6 3/4 (171 ) Mud Motors

6 3/4 (171 ) 6-7 3.1 Stage ERT A. Distance to stabilizer B. Box to Bend C. Overall Length D. Thread Prot. Diameter E. Kick Pad Diameter 22 76 7.19 7. Imperial 559 1,93 278 7,54 183 178 Metric Top Connection Bottom Connection Weight Maximum Flow Rate Maximum Torque Maximum Power Maximum Weight Dynamic on bit Static Maximum Allowable Pull Pull to Yield Motor AS PER REQUEST 4 1/2 Reg 4 1/2 Reg 1,884 65 8,235 27 87,3 247, 218,5 475, gpm ft- hp 838 2.46 11,165 21 38,8 19, 97, 212, m 3 /min N-m kw Bend Settings (degrees).26.52.78 1.3 1.27 1.5 1.72 1.93 2.12 2.3 2.6 2.82 2.95 3. Build Rate (degrees/1ft(3 m)) Hole Sizes (in, ) 8 1/2 8 3/4 9 7/8 216 223 251....36.. 2.38 1.32. 5.2 3.96.8 7.55 6.49 1.73 9.98 8.92 4.16 12.31 11.25 6.48 14.53 13.47 8.7 16.53 15.47 1.71 18.44 17.38 12.61 21.61 2.55 15.78 23.94 22.88 18.11 25.32 24.26 19.49 25.85 24.79 2.1 18

6 3/4 (171 ) 6-7 3.1 Stage ERT Maximum Pump Rate 65 gpm 2,461 Lpm Revolutions per unit volume.369 rev/gal.98 rev/l Pressure at full Load 1,175 psi 8,95 kpa Torque at full load 8,235 ft 11, 165 N-m 3 IMPERIAL PERFORMANCE CURVES 1 25 2 15 1 5 3 Torque 4 5 65 5 1 15 DIFFERENTIAL PRESSURE (psi) 8 6 4 2 TORQUE (ft ) Drilling Fluid Flow (GPM) 3 4 5 65 (off-bottom pressure) (PSI) 9 13 16 2 (on-bottom - off-bottom pressure) (PSI) 116 112 19 15 3 METRIC PERFORMANCE CURVES 14 25 12 2461 2 1 1893 8 15 1514 6 1 1136 4 5 2 2 4 6 8 1 Torque DIFFERENTIAL PRESSURE (kpa) TORQUE (N m) Drilling Fluid Flow (L/min) 1136 1514 1893 2461 (off-bottom pressure) (kpa) 621 896 113 1379 (on-bottom - off-bottom pressure) (kpa) 7998 7722 7515 7239 19

6 3/4 (171 ) 6-7 5. Stage A. Distance to stabilizer B. Box to Bend C. Overall Length D. Thread Prot. Diameter E. Kick Pad Diameter 22 76 7.19 7. Imperial 559 1,93 35 8,89 183 178 Metric Top Connection Bottom Connection Weight Maximum Flow Rate Maximum Torque Maximum Power Maximum Weight Dynamic on bit Static Maximum Allowable Pull Pull to Yield Motor AS PER REQUEST 4 1/2 Reg 4 1/2 Reg 2,229 6 6,23 177 87,3 247, 218,5 475, gpm ft- hp 952 2.27 8,45 132 38,8 19, 97, 212, m 3 /min N-m kw Bend Settings (degrees).26.52.78 1.3 1.27 1.5 1.72 1.93 2.12 2.3 2.6 2.82 2.95 3. Build Rate (degrees/1ft(3 m)) Hole Sizes (in, ) 8 1/2 8 3/4 9 7/8 216 223 251....39.. 1.7.9. 3.71 2.9.71 5.63 4.83 1.22 7.48 6.67 3.6 9.24 8.44 4.83 1.93 1.13 6.51 12.45 11.65 8.4 13.9 13.1 9.48 16.31 15.51 11.89 18.8 17.28 13.66 19.13 18.32 14.71 19.53 18.72 15.11 11

6 3/4 (171 ) 6-7 5. Stage Maximum Pump Rate 6 gpm 2,271 Lpm Revolutions per unit volume.292 rev/gal.77 rev/l Pressure at full Load 75 psi 5,17 kpa Torque at full load 6,23 ft 8,45 N m 18 16 14 12 1 8 6 4 2 IMPERIAL PERFORMANCE CURVES 6 5 4 3 25 5 75 DIFFERENTIAL PRESSURE (psi) 8 6 4 2 TORQUE (ft ) Drilling Fluid Flow (GPM) 3 4 5 6 (off-bottom pressure) (PSI) (on-bottom minus off-bottom pressure) (PSI) 51 83 15 127 699 667 645 623 2 175 15 125 1 75 5 25 METRIC PERFORMANCE CURVES 2271 1893 1514 1136 2 4 6 DIFFERENTIAL PRESSURE (kpa) 1 8 6 4 2 TORQUE (N m) Drilling Fluid Flow (L/min) 1136 1514 1893 2271 (off-bottom pressure) (kpa) (on-bottom minus off-bottom pressure) (kpa) 352 572 724 876 4819 4599 4447 4295 111

6 3/4 (171 ) 6-7 5. Stage HR A. Distance to stabilizer B. Box to Bend C. Overall Length D. Thread Prot. Diameter E. Kick Pad Diameter 22 76 7.19 7. Imperial 559 1,93 35 8,89 183 178 Metric Top Connection Bottom Connection Weight Maximum Flow Rate Maximum Torque Maximum Power Maximum Weight Dynamic on bit Static Maximum Allowable Pull Pull to Yield Motor AS PER REQUEST 4 1/2 Reg 4 1/2 Reg 2,229 6 9,35 29 87,3 247, 218,5 475, gpm ft- hp 952 2.27 12,68 216 38,8 19, 97, 212, m 3 /min N-m kw Bend Settings (degrees).26.52.78 1.3 1.27 1.5 1.72 1.93 2.12 2.3 2.6 2.82 2.95 3. Build Rate (degrees/1ft(3 m)) Hole Sizes (in, ) 8 1/2 8 3/4 9 7/8 216 223 251....39.. 1.7.9. 3.71 2.9.71 5.63 4.83 1.22 7.48 6.67 3.6 9.24 8.44 4.83 1.93 1.13 6.51 12.45 11.65 8.4 13.9 13.1 9.48 16.31 15.51 11.89 18.8 17.28 13.66 19.13 18.32 14.71 19.53 18.72 15.11 112

6 3/4 (171 ) 6-7 5. Stage HR Maximum Pump Rate 6 gpm 2,27 Lpm Revolutions per unit volume.292 rev/gal.77 rev/l Pressure at full Load 1,13 psi 7,76 kpa Torque at full load 9,35 ft 12,68 N m 2 175 15 125 1 75 5 25 IMPERIAL PERFORMANCE CURVES 12 6 5 4 3 3 6 9 12 DIFFERENTIAL PRESSURE (psi) 9 6 3 TORQUE (ft ) Drilling Fluid Flow (GPM) 3 4 5 6 (off-bottom pressure) (PSI) (on-bottom minus off-bottom pressure) (PSI) 79 91 117 129 151 139 113 11 2 16 12 8 4 METRIC PERFORMANCE CURVES 2271 1893 1514 1136 25 5 75 DIFFERENTIAL PRESSURE (kpa) 14 15 7 35 TORQUE (N m) Drilling Fluid Flow (L/min) 1136 1514 1893 2271 (off-bottom pressure) (kpa) (on-bottom minus off-bottom pressure) (kpa) 545 627 87 889 7246 7164 6984 692 113

6 3/4 (171 ) 7-8 2.9 Stage Slow A. Distance to stabilizer B. Box to Bend C. Overall Length D. Thread Prot. Diameter E. Kick Pad Diameter 22 76 7.19 7. Imperial 559 1,93 37 9,39 183 178 Metric Top Connection Bottom Connection Weight Maximum Flow Rate Maximum Torque Maximum Power Maximum Weight Dynamic on bit Static Maximum Allowable Pull Pull to Yield Motor AS PER REQUEST 4 1/2 Reg 4 1/2 Reg 2,442 5 7,42 163 87,3 247, 218,5 475, gpm ft- hp 1,86 1.89 1,36 122 38,8 19, 97, 212, m 3 /min N-m kw Bend Settings (degrees).26.52.78 1.3 1.27 1.5 1.72 1.93 2.12 2.3 2.6 2.82 2.95 3. Build Rate (degrees/1ft(3 m)) Hole Sizes (in, ) 8 1/2 8 3/4 9 7/8 216 223 251....38.. 1.58.83. 3.47 2.71.68 5.27 4.52 1.13 7.1 6.26 2.86 8.67 7.92 4.52 1.25 9.5 6.11 11.69 1.93 7.54 13.5 12.29 8.9 15.31 16.22 11.16 16.97 16.56 12.82 17.96 17.2 13.81 18.33 17.58 14.18 114

6 3/4 (171 ) 7-8 2.9 Stage Slow Maximum Pump Rate 5 gpm 1,893 Lpm Revolutions per unit volume.144 rev/gal.38 rev/l Pressure at full Load 56 psi 3,861 kpa Torque at full load 7,42 ft 1,36 N m 8 7 6 5 4 3 2 1 IMPERIAL PERFORMANCE CURVES 2 Torque 4 5 6 1 2 3 4 5 6 DIFFERENTIAL PRESSURE (psi) 8 6 4 2 TORQUE (ft ) Drilling Fluid Flow (GPM) 2 4 5 6 (off-bottom pressure) (PSI) 44 17 153 21 (on-bottom - off-bottom pressure) (PSI) 516 453 47 35 8 7 6 5 4 3 2 1 Torque METRIC PERFORMANCE CURVES 757 1514 1893 2271 1 2 3 4 DIFFERENTIAL PRESSURE (kpa) 12 1 8 6 4 2 TORQUE (N m) Drilling Fluid Flow (L/min) 757 1514 1893 2271 (off-bottom pressure) (kpa) 33 738 155 1448 (on-bottom - off-bottom pressure) (kpa) 3558 3123 286 2413 115

6 3/4 (171 ) 7-8 3. Stage A. Distance to stabilizer B. Box to Bend C. Overall Length D. Thread Prot. Diameter E. Kick Pad Diameter 22 76 7.19 7. Imperial 559 1,93 275 6,985 183 178 Metric Top Connection Bottom Connection Weight Maximum Flow Rate Maximum Torque Maximum Power Maximum Weight Dynamic on bit Static Maximum Allowable Pull Pull to Yield Motor AS PER REQUEST 4 1/2 Reg 4 1/2 Reg 1,835 6 4,19 12 87,3 247, 218,5 475, gpm ft- hp 816 2.27 5,681 76 38,8 19, 97, 212, m 3 /min N-m kw Bend Settings (degrees).26.52.78 1.3 1.27 1.5 1.72 1.93 2.12 2.3 2.6 2.82 2.95 3. Build Rate (degrees/1ft(3 m)) Hole Sizes (in, ) 8 1/2 8 3/4 9 7/8 216 223 251....37.. 2.33 1.29. 4.93 3.89.8 7.43 6.38 1.7 9.82 8.77 4.9 12.1 11.6 6.37 14.29 13.25 8.56 16.27 15.22 1.53 18.14 17.1 12.41 21.27 2.22 15.53 23.56 22.51 17.82 24.91 23.87 19.17 25.44 24.39 19.69 116

6 3/4 (171 ) 7-8 3. Stage Maximum Pump Rate 6 gpm 2,271 Lpm Revolutions per unit volume.283 rev/gal.75 rev/l Pressure at full Load 45 psi 3,13 kpa Torque at full load 4,19 ft 5,681 N m 18 16 14 12 1 8 6 4 2 IMPERIAL PERFORMANCE CURVES 3 Torque 4 5 6 1 2 3 4 5 DIFFERENTIAL PRESSURE (psi) 4 3 2 1 TORQUE (ft ) Drilling Fluid Flow (GPM) 3 4 5 6 (off-bottom pressure) (PSI) 38 68 16 152 (on-bottom - off-bottom pressure) (PSI) 412 382 344 298 18 16 14 12 1 8 6 4 2 METRIC PERFORMANCE CURVES 1136 Torque 1514 1893 2271 1 2 3 DIFFERENTIAL PRESSURE (kpa) 6 5 4 3 2 1 TORQUE (N m) Drilling Fluid Flow (L/min) 1136 1514 1893 2271 (off-bottom pressure) (kpa) 262 469 731 148 (on-bottom - off-bottom pressure) (kpa) 2841 2634 2372 255 117

6 3/4 (171 ) 7-8 5. Stage A. Distance to stabilizer B. Box to Bend C. Overall Length D. Thread Prot. Diameter E. Kick Pad Diameter 22 76 7.19 7. Imperial 559 1,93 345 8,763 183 178 Metric Top Connection Bottom Connection Weight Maximum Flow Rate Maximum Torque Maximum Power Maximum Weight Dynamic on bit Static Maximum Allowable Pull Pull to Yield Motor AS PER REQUEST 4 1/2 Reg 4 1/2 Reg 2,31 6 6,98 19 87,3 247, 218,5 475, gpm ft- hp 1,28 2.27 9,46 142 38,8 19, 97, 212, m 3 /min N-m kw Bend Settings (degrees).26.52.78 1.3 1.27 1.5 1.72 1.93 2.12 2.3 2.6 2.82 2.95 3. Build Rate (degrees/1ft(3 m)) Hole Sizes (in, ) 8 1/2 8 3/4 9 7/8 216 223 251....39.. 1.74.92. 3.79 2.97.72 5.75 4.93 1.25 7.64 6.82 3.13 9.44 8.62 4.93 11.16 1.34 6.65 12.72 11.9 8.21 14.19 13.37 9.68 16.65 15.83 12.14 18.46 17.64 13.95 19.52 18.7 15.1 19.93 19.11 15.42 118

6 3/4 (171 ) 7-8 5. Stage Maximum Pump Rate 6 gpm 2,271 Lpm Revolutions per unit volume.288 rev/gal.76 rev/l Pressure at full Load 75 psi 5,17 kpa Torque at full load 6,98 ft 9,46 N m 2 IMPERIAL PERFORMANCE CURVES 8 16 12 8 4 5 4 3 6 6 4 2 TORQUE (ft ) 3 6 9 DIFFERENTIAL PRESSURE (psi) Drilling Fluid Flow (GPM) 3 4 5 6 (off-bottom pressure) (PSI) (on-bottom minus off-bottom pressure) (PSI) 51 83 15 127 699 667 645 623 2 METRIC PERFORMANCE CURVES 1 175 15 125 1 75 5 25 2271 1893 1514 1136 8 6 4 2 TORQUE (N m) 2 4 6 DIFFERENTIAL PRESSURE (kpa) Drilling Fluid Flow (L/min) 1136 1514 1893 2271 (off-bottom pressure) (kpa) (on-bottom minus off-bottom pressure) (kpa) 352 572 724 876 4819 4599 4447 4295 119

6 3/4 (171 ) 7-8 5. Stage HR A. Distance to stabilizer B. Box to Bend C. Overall Length D. Thread Prot. Diameter E. Kick Pad Diameter 22 76 7.19 7. Imperial 559 1,93 354 8,992 183 178 Metric Top Connection Bottom Connection Weight Maximum Flow Rate Maximum Torque Maximum Power Maximum Weight Dynamic on bit Static Maximum Allowable Pull Pull to Yield Motor AS PER REQUEST 4 1/2 Reg 4 1/2 Reg 2,319 6 1,64 323 87,3 247, 218,5 475, gpm ft- hp 1,32 2.3 14,19 241 38,8 19, 97, 212, m 3 /min N-m kw Bend Settings (degrees).26.52.78 1.3 1.27 1.5 1.72 1.93 2.12 2.3 2.6 2.82 2.95 3. Build Rate (degrees/1ft(3 m)) Hole Sizes (in, ) 8 1/2 8 3/4 9 7/8 216 223 251....39.. 1.74.92. 3.79 2.97.72 5.75 4.93 1.25 7.64 6.82 4.93 9.44 8.62 4.93 11.16 1.34 6.65 12.72 11.9 8.21 14.19 13.37 9.68 16.65 15.93 12.14 18.46 17.64 13.95 19.52 18.7 15.1 19.93 19.11 15.42 12

6 3/4 (171 ) 7-8 5. Stage HR Maximum Pump Rate 6 gpm 2271 Lpm Revolutions per unit volume.288 rev/gal.76 rev/l Pressure at full Load 113 psi 776 kpa Torque at full load 146 ft 1419 N m 2 IMPERIAL PERFORMANCE CURVES 12 175 15 125 1 75 5 25 3 Torq ue 4 5 6 2 4 6 8 1 12 DIFFERENTIAL PRESSURE (psi) 9 6 3 TORQUE (ft ) Drilling Fluid Flow (GPM) 3 4 5 6 (off-bottom pressure) (PSI) 79 91 117 129 (on-bottom minus off-bottom pressure) (PSI) 151 139 113 11 2 METRIC PERFORMANCE CURVES 16 175 15 125 1 75 5 25 1136 Torq ue 1514 1893 2271 2 4 6 8 1 DIFFERENTIAL PRESSURE (kpa) 14 12 1 8 6 4 2 TORQUE (N m) Drilling Fluid Flow (L/min) 1136 1514 1893 2271 (off-bottom pressure) (kpa) 545 627 87 889 (on-bottom minus off-bottom pressure) (kpa) 7246 7164 6984 692 121

6 3/4 (171 ) 7-8 5.7 Stage A. Distance to stabilizer B. Box to Bend C. Overall Length D. Thread Prot. Diameter E. Kick Pad Diameter 22 76 7.19 7. Imperial 559 1,93 41 1,414 183 178 Metric Top Connection Bottom Connection Weight Maximum Flow Rate Maximum Torque Maximum Power Maximum Weight Dynamic on bit Static Maximum Allowable Pull Pull to Yield Motor AS PER REQUEST 4 1/2 Reg 4 1/2 Reg 2,326 6 9,15 222 87,3 247, 218,5 475, gpm ft- hp 1,35 2.3 12,4 166 38,8 19, 97, 212, m 3 /min N-m kw Bend Settings (degrees).26.52.78 1.3 1.27 1.5 1.72 1.93 2.12 2.3 2.6 2.82 2.95 3. Build Rate (degrees/1ft(3 m)) Hole Sizes (in, ) 8 1/2 8 3/4 9 7/8 216 223 251....26.. 1.38.71. 3.5 2.38.63 4.65 3.98.98 6.19 5.52 2.52 7.66 6.99 3.99 9.6 8.4 5.39 1.34 9.67 6.66 11.54 1.87 7.87 13.55 12.88 9.87 15.2 14.36 11.35 15.89 15.22 12.22 16.23 15.56 12.55 122

6 3/4 (171 ) 7-8 5.7 Stage Maximum Pump Rate 6 gpm 2,271 Lpm Revolutions per unit volume.242 rev/gal.64 rev/l Pressure at full Load 86 psi 5,9 kpa Torque at full load 9,15 ft 12,4 N m 16 14 12 1 8 6 4 2 IMPERIAL PERFORMANCE CURVES 6 5 4 3 Torq ue 2 4 6 8 1 DIFFERENTIAL PRESSURE (psi) 15 9 75 6 45 3 15 TORQUE (ft ) Drilling Fluid Flow (GPM) 3 4 5 6 (off-bottom pressure) (PSI) 51 76 87 15 (on-bottom minus off-bottom pressure) (PSI) 89 784 773 755 16 14 12 1 8 6 4 2 METRIC PERFORMANCE CURVES 1136 Torq ue 1514 1893 2271 2 4 6 8 DIFFERENTIAL PRESSURE (kpa) 14 12 1 8 6 4 2 TORQUE (N m) Drilling Fluid Flow (L/min) 1136 1514 1893 2271 (off-bottom pressure) (kpa) 352 524 6 724 (on-bottom minus off-bottom pressure) (kpa) 5578 545 533 526 123

6 3/4 (171 ) 7-8 5.7 Stage HR A. Distance to stabilizer B. Box to Bend C. Overall Length D. Thread Prot. Diameter E. Kick Pad Diameter 22 76 7.19 7. Imperial 559 1,93 41 1,414 183 178 Metric Top Connection Bottom Connection Weight Maximum Flow Rate Maximum Torque Maximum Power Maximum Weight Dynamic on bit Static Maximum Allowable Pull Pull to Yield Motor AS PER REQUEST 4 1/2 Reg 4 1/2 Reg 2,326 6 13,72 355 87,3 247, 218,5 475, gpm ft- hp 1,35 2.3 18,6 265 38,8 19, 97, 212, m 3 /min N-m kw Bend Settings (degrees).26.52.78 1.3 1.27 1.5 1.72 1.93 2.12 2.3 2.6 2.82 2.95 3. Build Rate (degrees/1ft(3 m)) Hole Sizes (in, ) 8 1/2 8 3/4 9 7/8 216 223 251....26.. 1.38.71. 3.5 2.38.63 4.65 3.98.98 6.19 5.52 2.52 7.66 6.99 3.99 9.6 8.4 5.39 1.34 9.67 6.66 11.54 1.87 7.87 13.55 12.88 9.87 15.2 14.36 11.35 15.89 15.22 12.22 16.23 15.56 12.55 124

6 3/4 (171 ) 7-8 5.7 Stage HR Maximum Pump Rate 6 gpm 2,271 Lpm Revolutions per unit volume.242 rev/gal.64 rev/l Pressure at full Load 1,28 psi 8,84 kpa Torque at full load 13,72 ft 18,6 N m 175 15 125 1 75 5 25 IMPERIAL PERFORMANCE CURVES 16 14 6 12 5 1 4 8 3 6 4 2 25 5 75 1 125 15 DIFFERENTIAL PRESSURE (psi) TORQUE (ft ) Drilling Fluid Flow (GPM) 3 4 5 6 (off-bottom pressure) (PSI) 151 176 187 25 (on-bottom minus off-bottom pressure) (PSI) 1129 114 193 175 16 14 12 1 8 6 4 2 METRIC PERFORMANCE CURVES 2271 1893 1514 1136 5 1 DIFFERENTIAL PRESSURE (kpa) 2 175 15 125 1 75 5 25 TORQUE (N m) Drilling Fluid Flow (L/min) 1136 1514 1893 2271 (off-bottom pressure) (kpa) 141 1213 1289 1413 (on-bottom minus off-bottom pressure) (kpa) 7784 7612 7536 7412 125

8 (23 ) Mud Motors

8 (23 ) 4-5 3.6 Stage A. Distance to stabilizer B. Box to Bend C. Overall Length D. Thread Prot. Diameter E. Kick Pad Diameter 28 87 8.63 8.6 Imperial 711 2,21 33 8,382 219 25 Metric Top Connection Bottom Connection Weight Maximum Flow Rate Maximum Torque Maximum Power Maximum Weight Dynamic on bit Static Maximum Allowable Pull Pull to Yield Motor AS PER REQUEST 6 5/8 Reg 6 5/8 Reg 2,859 9 4,366 261 139,5 412,8 324, 93, gpm ft- hp 1,272 3.41 5,92 195 62, 183, 144, 414, m 3 /min N-m kw Bend Settings (degrees).26.52.78 1.3 1.27 1.5 1.72 1.93 2.12 2.3 2.6 2.82 2.95 3. Build Rate (degrees/1ft(3 m)) Hole Sizes (in, ) 9 7/8 1 5/8 12 1/4 251 27 311....59.. 2.9.34. 5.12 2.56. 7.26 4.69.86 9.3 6.74 1.18 11.26 8.7 3.14 13.13 1.57 5.1 14.82 12.23 6.7 16.43 13.86 8.3 19.1 16.53 1.97 21.6 18.49 12.93 22.22 19.65 14.9 22.67 2.1 14.54 128

8 (23 ) 4-5 3.6 Stage Maximum Pump Rate 9 gpm 3,47 Lpm Revolutions per unit volume.244 rev/gal.65 rev/l Pressure at full Load 497 psi 3,427 kpa Torque at full load 4,294 ft 5,822 N m 25 2 15 1 5 IMPERIAL PERFORMANCE CURVES 9 8 6 4 2 4 6 DIFFERENTIAL PRESSURE (psi) 5 45 4 35 3 25 2 15 1 5 TORQUE (ft ) Drilling Fluid Flow (GPM) 4 6 8 9 (off-bottom pressure) (PSI) 36 52 73 86 (on-bottom minus off-bottom pressure) (PSI) 461 445 424 411 25 METRIC PERFORMANCE CURVES 7 2 15 1 5 1514 2271 347 328 1 2 3 4 DIFFERENTIAL PRESSURE (kpa) 6 5 4 3 2 1 TORQUE (N m) Drilling Fluid Flow (L/min) 1514 2271 328 347 (off-bottom pressure) (kpa) 248 359 53 593 (on-bottom minus off-bottom pressure) (kpa) 3178 368 2923 2834 129

8 (23 ) 7-8 2. Stage A. Distance to stabilizer B. Box to Bend C. Overall Length D. Thread Prot. Diameter E. Kick Pad Diameter 28 87 8.63 8.6 Imperial 711 2,21 33 8,382 219 25 Metric Top Connection Bottom Connection Weight Maximum Flow Rate Maximum Torque Maximum Power Maximum Weight Dynamic on bit Static Maximum Allowable Pull Pull to Yield Motor AS PER REQUEST 6 5/8 Reg 6 5/8 Reg 2,914 8 8,95 175 139,5 412,8 324, 93, gpm ft- hp 1,296 3.3 9,563 131 62, 183, 144, 414, m 3 /min N-m kw Bend Settings (degrees).26.52.78 1.3 1.27 1.5 1.72 1.93 2.12 2.3 2.6 2.82 2.95 3. Build Rate (degrees/1ft(3 m)) Hole Sizes (in, ) 9 7/8 1 5/8 12 1/4 251 27 311....59.. 2.9.34. 5.12 2.56. 7.26 4.69.86 9.3 6.74 1.18 11.26 8.7 3.14 13.13 1.57 5.1 14.82 12.23 6.7 16.43 13.86 8.3 19.1 16.53 1.97 21.6 18.49 12.93 22.22 19.65 14.9 22.67 2.1 14.54 13

8 (23 ) 7-8 2. Stage Maximum Pump Rate 8 gpm 3,28 Lpm Revolutions per unit volume.96 rev/gal.25 rev/l Pressure at full Load 374 psi 2,579 kpa Torque at full load 7,53 ft 9,563 N m 9 8 7 6 5 4 3 2 1 IMPERIAL PERFORMANCE CURVES Torque 4 5 6 8 1 2 3 4 DIFFERENTIAL PRESSURE (psi) 8 7 6 5 4 3 2 1 TORQUE (ft ) Drilling Fluid Flow (GPM) 4 5 6 8 (off-bottom pressure) (PSI) 58 82 112 189 (on-bottom - off-bottom pressure) (PSI) 316 292 262 185 9 8 7 6 5 4 3 2 1 Torque METRIC PERFORMANCE CURVES 1514 1893 2271 328 5 1 15 2 25 3 DIFFERENTIAL PRESSURE (kpa) 12 1 8 6 4 2 TORQUE (N m) Drilling Fluid Flow (L/min) 1514 1893 2271 328 (off-bottom pressure) (kpa) 4 565 772 133 (on-bottom - off-bottom pressure) (kpa) 2179 213 186 1276 131

8 (23 ) 7-8 3.4 ESX3 Stage A. Distance to stabilizer B. Box to Bend C. Overall Length D. Thread Prot. Diameter E. Kick Pad Diameter 28 87 8.63 8.6 Imperial 711 2,21 365.2 9,276 219 25 Metric Top Connection Bottom Connection Weight Maximum Flow Rate Maximum Torque Maximum Power Maximum Weight Dynamic on bit Static Maximum Allowable Pull Pull to Yield Motor AS PER REQUEST 6 5/8 Reg 6 5/8 Reg 2,914 9 14,3 154 139,5 412,8 324, 93, gpm ft- hp 1,296 3.261 19,39 115 62, 183, 144, 414, m 3 /min N-m kw Bend Settings (degrees).26.52.78 1.3 1.27 1.5 1.72 1.93 2.12 2.3 2.6 2.82 2.95 3. Build Rate (degrees/1ft(3 m)) Hole Sizes (in, ) 9 7/8 1 5/8 12 1/4 251 27 311.......96.. 2.25.98. 3.49 2.22. 4.68 3.41.64 5.82 4.54 1.78 6.9 5.63 2.86 7.88 6.61 3.84 8.81 7.54 4.77 1.36 9.8 6.32 11.49 1.22 7.46 11.91 1.63 7.87 12.42 11.15 8.39 132

8 (23 ) 7-8 3.4 ESX3 Stage Maximum Pump Rate 9 gpm 3,41 Lpm Revolutions per unit volume.89 rev/gal.24 rev/l Pressure at full Load 51 psi 3,52 kpa Torque at full load 14,3 ft 19,39 N m 9 8 7 6 5 4 3 2 1 IMPERIAL PERFORMANCE CURVES 9 75 55 4 1 2 3 4 5 6 DIFFERENTIAL PRESSURE (psi) 16 14 12 1 8 6 4 2 TORQUE (ft ) Drilling Fluid Flow (GPM) 4 55 75 9 (off-bottom pressure) (PSI) (on-bottom minus off-bottom pressure) (PSI) 67 92 125 15 443 418 385 36 1 METRIC PERFORMANCE CURVES 25 75 5 25 347 2839 282 1514 1 2 3 4 DIFFERENTIAL PRESSURE (kpa) 2 15 1 5 TORQUE (N m) Drilling Fluid Flow (L/min) 1514 282 2839 347 (off-bottom pressure) (kpa) (on-bottom minus off-bottom pressure) (kpa) 46 632 862 134 357 2884 2654 2482 133

8 (23 ) 7-8 4. Stage A. Distance to stabilizer B. Box to Bend C. Overall Length D. Thread Prot. Diameter E. Kick Pad Diameter 28 87 8.63 8.6 Imperial 711 2,21 365 9,281 219 25 Metric Top Connection Bottom Connection Weight Maximum Flow Rate Maximum Torque Maximum Power Maximum Weight Dynamic on bit Static Maximum Allowable Pull Pull to Yield Motor AS PER REQUEST 6 5/8 Reg 6 5/8 Reg 3,419 9 9,95 224 139,5 412,8 324, 93, gpm ft- hp 1,521 3.41 13,49 167 62, 183, 144, 414, m 3 /min N-m kw Bend Settings (degrees).26.52.78 1.3 1.27 1.5 1.72 1.93 2.12 2.3 2.6 2.82 2.95 3. Build Rate (degrees/1ft(3 m)) Hole Sizes (in, ) 9 7/8 1 5/8 12 1/4 251 27 311....42.. 2.45.2. 4.39 2.15. 6.26 4.2.84 8.6 5.81.95 9.77 7.53 2.66 11.41 9.16 4.3 12.89 1.64 5.78 14.29 12.5 7.18 16.63 14.39 9.52 18.35 16.1 11.24 19.36 17.12 12.25 19.75 17.51 12.64 134

8 (23 ) 7-8 4. Stage Maximum Pump Rate 9 gpm 3,47 Lpm Revolutions per unit volume.166 rev/gal.44 rev/l Pressure at full Load 6 psi 4,14 kpa Torque at full load 9,95 ft 13,49 N m 175 15 125 1 75 5 25 IMPERIAL PERFORMANCE CURVES 9 75 55 4 2 4 6 DIFFERENTIAL PRESSURE (psi) 12 8 4 TORQUE (ft ) Drilling Fluid Flow (GPM) 4 55 75 9 (off-bottom pressure) (PSI) (on-bottom minus off-bottom pressure) (PSI) 44 87 18 16 556 513 492 44 175 15 125 1 75 5 25 METRIC PERFORMANCE CURVES 347 2839 282 1514 2 4 DIFFERENTIAL PRESSURE (kpa) 16 12 8 4 TORQUE (N m) Drilling Fluid Flow (L/min) 1514 282 2839 347 (off-bottom pressure) (kpa) (on-bottom minus off-bottom pressure) (kpa) 33 6 745 113 3833 3537 3392 334 135

8 (23 ) 7-8 4. Stage HR A. Distance to stabilizer B. Box to Bend C. Overall Length D. Thread Prot. Diameter E. Kick Pad Diameter 28 87 8.63 8.6 Imperial 711 2,21 365 9,281 219 25 Metric Top Connection Bottom Connection Weight Maximum Flow Rate Maximum Torque Maximum Power Maximum Weight Dynamic on bit Static Maximum Allowable Pull Pull to Yield Motor AS PER REQUEST 6 5/8 Reg 6 5/8 Reg 3,419 9 14,93 41 139,5 412,8 324, 93, gpm ft- hp 1,521 3.41 2,24 299 62, 183, 144, 414, m 3 /min N-m kw Bend Settings (degrees).26.52.78 1.3 1.27 1.5 1.72 1.93 2.12 2.3 2.6 2.82 2.95 3. Build Rate (degrees/1ft(3 m)) Hole Sizes (in, ) 9 7/8 1 5/8 12 1/4 251 27 311....42.. 2.45.2. 4.39 2.15. 6.26 4.2.84 8.6 5.81.95 9.77 7.53 2.66 11.41 9.16 4.3 12.89 1.64 5.78 14.29 12.5 7.18 16.63 14.39 9.52 18.35 16.1 11.24 19.36 17.12 12.25 19.75 17.51 12.64 136

8 (23 ) 7-8 4. Stage HR Maximum Pump Rate 9 gpm 3,47 Lpm Revolutions per unit volume.166 rev/gal.44 rev/l Pressure at full Load 9 psi 6,21 kpa Torque at full load 14,93 ft 2,24 N m 175 IMPERIAL PERFORMANCE CURVES 16 15 125 1 75 5 25 4 55 75 9 12 8 4 TORQUE (ft ) 5 1 DIFFERENTIAL PRESSURE (psi) Drilling Fluid Flow (GPM) 4 55 75 9 (off-bottom pressure) (PSI) (on-bottom minus off-bottom pressure) (PSI) 61 93 12 147 839 87 78 753 175 15 125 1 75 5 25 METRIC PERFORMANCE CURVES 347 2839 282 1514 2 4 6 DIFFERENTIAL PRESSURE (kpa) 24 2 16 12 8 4 TORQUE (N m) Drilling Fluid Flow (L/min) 1514 282 2839 347 (off-bottom pressure) (kpa) (on-bottom minus off-bottom pressure) (kpa) 421 641 827 114 5785 5564 5378 5192 137

9 5/8 (244 ) Mud Motors

9 5/8 (244 ) 3-4 4.5 Stage A. Distance to stabilizer B. Box to Bend C. Overall Length D. Thread Prot. Diameter E. Kick Pad Diameter 28 92 1.75 9.75 Imperial 711 2,337 348 8,839 273 248 Metric Top Connection Bottom Connection Weight Maximum Flow Rate Maximum Torque Maximum Power Maximum Weight Dynamic on bit Static Maximum Allowable Pull Pull to Yield Motor 4,48 1,2 6,78 434 6 5/8 Reg 179,3 551, 495, 1,53, AS PER REQUEST gpm ft- hp 1,993 4.54 9,192 324 6 5/8 Reg 79,7 245, 22, 681, m 3 /min N-m kw Bend Settings (degrees).26.52.78 1.3 1.27 1.5 1.72 1.93 2.12 2.3 2.6 2.82 2.95 3. Build Rate (degrees/1ft(3 m)) Hole Sizes (in, ) 12 1/4 13 3/4 17 1/2 311 375 445....23.. 1.89.. 3.92.. 5.87.. 7.74 1.26. 9.54 3.5. 11.25 4.76. 12.79 6.31. 14.26 7.78.64 16.71 1.22 3.8 18.5 12.1 4.88 19.56 13.7 5.93 19.97 13.48 6.34 14

9 5/8 (244 ) 3-4 4.5 Stage Maximum Pump Rate 1,2 gpm 4,542 Lpm Revolutions per unit volume.188 rev/gal.5 rev/l Pressure at full Load 62 psi 4,275 kpa Torque at full load 6,78 ft 9,192 N m 25 IMPERIAL PERFORMANCE CURVES 8 2 15 1 5 6 7 Torque 12 1 2 4 6 DIFFERENTIAL PRESSURE (psi) 6 4 2 TORQUE (ft ) Drilling Fluid Flow (GPM) 6 7 1 12 (off-bottom pressure) (PSI) 32 34 44 52 (on-bottom - off-bottom pressure) (PSI) 588 586 576 568 25 METRIC PERFORMANCE CURVES 1 2 4542 8 3785 15 265 6 1 2271 4 5 2 1 2 3 4 5 Torque DIFFERENTIAL PRESSURE (kpa) TORQUE (N m) Drilling Fluid Flow (L/min) 2271 265 3785 4542 (off-bottom pressure) (kpa) 221 234 33 359 (on-bottom - off-bottom pressure) (kpa) 454 44 3971 3916 141

9 5/8 (244 ) 3-4 6. Stage A. Distance to stabilizer B. Box to Bend C. Overall Length D. Thread Prot. Diameter E. Kick Pad Diameter 28 92 1.75 9.75 Imperial 711 2,337 398 1,19 273 248 Metric Top Connection Bottom Connection Weight Maximum Flow Rate Maximum Torque Maximum Power Maximum Weight Dynamic on bit Static Maximum Allowable Pull Pull to Yield Motor 5,92 1,2 8,272 536 6 5/8 Reg 179,3 551, 495, 1,53, AS PER REQUEST gpm ft- hp 2,265 4.54 11,215 4 6 5/8 Reg 79,7 245, 22, 681, m 3 /min N-m kw Bend Settings (degrees).26.52.78 1.3 1.27 1.5 1.72 1.93 2.12 2.3 2.6 2.82 2.95 3. Build Rate (degrees/1ft(3 m)) Hole Sizes (in, ) 12 1/4 13 3/4 17 1/2 311 375 445....31.. 1.49.. 3.23.. 4.9.63. 6.5.97. 8.3 2.5. 9.49 3.96. 1.81 5.28. 12.6 6.53.44 14.15 8.62 2.53 15.68 1.15 4.6 16.59 11.6 4.97 16.94 11.4 5.31 142

9 5/8 (244 ) 3-4 6. Stage Maximum Pump Rate 1,2 gpm 4,54 Lpm Revolutions per unit volume.225 rev/gal.59 rev/l Pressure at full Load 765 psi 5,275 kpa Torque at full load 8,272 ft 11,215 N m 3 IMPERIAL PERFORMANCE CURVES 12 25 2 15 1 5 12 1 8 8 6 2 4 6 8 DIFFERENTIAL PRESSURE (psi) 4 TORQUE (ft ) Drilling Fluid Flow (GPM) 6 8 1 12 (off-bottom pressure) (PSI) 46 51 58 66 (on-bottom - off-bottom pressure) (PSI) 719 714 77 699 3 METRIC PERFORMANCE CURVES 15 25 2 15 1 5 4542 3785 328 2271 2 4 6 DIFFERENTIAL PRESSURE (kpa) 1 5 TORQUE (N m) Drilling Fluid Flow (L/min) 2271 328 3785 4542 (off-bottom pressure) (kpa) 317 352 4 455 (on-bottom - off-bottom pressure) (kpa) 4957 4923 4875 4819 143

9 5/8 (244 ) 5-6 3. Stage A. Distance to stabilizer B. Box to Bend C. Overall Length D. Thread Prot. Diameter E. Kick Pad Diameter 28 92 1.75 9.75 Imperial 711 2,337 348 8,839 273 248 Metric Top Connection Bottom Connection Weight Maximum Flow Rate Maximum Torque Maximum Power Maximum Weight Dynamic on bit Static Maximum Allowable Pull Pull to Yield Motor 4,483 1,2 1,94 189 6 5/8 Reg 179,3 551, 495, 1,53, AS PER REQUEST gpm ft- hp 1,994 4.54 14,833 139 6 5/8 Reg 79,7 245, 22, 681, m 3 /min N-m kw Bend Settings (degrees).26.52.78 1.3 1.27 1.5 1.72 1.93 2.12 2.3 2.6 2.82 2.95 3. Build Rate (degrees/1ft(3 m)) Hole Sizes (in, ) 12 1/4 13 3/4 17 1/2 311 375 445....23.. 1.89.. 3.92.. 5.87.. 7.74 1.26. 9.54 3.5. 11.25 4.76. 12.79 6.31. 14.26 7.78.64 16.71 1.22 3.8 18.5 12.1 4.88 19.56 13.7 5.93 19.97 13.48 6.34 144

9 5/8 (244 ) 5-6 3. Stage Maximum Pump Rate 1,2 gpm 4,542 Lpm Revolutions per unit volume.117 rev/gal.31 rev/l Pressure at full Load 45 psi 3,13 kpa Torque at full load 1,94 ft 14,833 N m 14 12 1 8 6 4 2 IMPERIAL PERFORMANCE CURVES 6 Torque 8 1 12 1 2 3 4 5 DIFFERENTIAL PRESSURE (psi) 12 1 8 6 4 2 TORQUE (ft ) Drilling Fluid Flow (GPM) 6 8 1 12 (off-bottom pressure) (PSI) 29 43 62 85 (on-bottom - off-bottom pressure) (PSI) 421 47 388 365 14 12 1 8 6 4 2 METRIC PERFORMANCE CURVES 2271 Torque 328 3785 4542 1 2 3 DIFFERENTIAL PRESSURE (kpa) 15 125 1 75 5 25 TORQUE (N m) Drilling Fluid Flow (L/min) 2271 328 3785 4542 (off-bottom pressure) (kpa) 2 296 427 586 (on-bottom - off-bottom pressure) (kpa) 293 286 2675 2517 145

9 5/8 (244 ) 5-6 5. Stage A. Distance to stabilizer B. Box to Bend C. Overall Length D. Thread Prot. Diameter E. Kick Pad Diameter 28 92 1.75 9.75 Imperial 711 2,337 42 1,211 273 248 Metric Top Connection Bottom Connection Weight Maximum Flow Rate Maximum Torque Maximum Power Maximum Weight Dynamic on bit Static Maximum Allowable Pull Pull to Yield Motor 5,365 1,3 16,12 44 6 5/8 Reg 179,3 551, 495, 1,53, AS PER REQUEST gpm ft- hp 2,386 4.921 21,85 32 6 5/8 Reg 79,7 245, 22, 681, m 3 /min N-m kw Bend Settings (degrees).26.52.78 1.3 1.27 1.5 1.72 1.93 2.12 2.3 2.6 2.82 2.95 3. Build Rate (degrees/1ft(3 m)) Hole Sizes (in, ) 12 1/4 13 3/4 17 1/2 311 375 445....23.. 1.89.. 3.92.. 5.87.. 7.74 1.26. 9.54 3.5. 11.25 4.76. 12.79 6.31. 14.26 7.78.64 16.71 1.22 3.8 18.5 12.1 4.88 19.56 13.7 5.93 19.97 13.48 6.34 146

9 5/8 (244 ) 5-6 5. Stage Maximum Pump Rate 1,3 gpm 4,92 Lpm Revolutions per unit volume.138 rev/gal.36 rev/l Pressure at full Load 75 psi 5,17 kpa Torque at full load 16,12 ft 21,85 N m 2 IMPERIAL PERFORMANCE CURVES 2 15 1 5 13 1 9 7 16 12 8 4 TORQUE (ft ) 2 4 6 8 DIFFERENTIAL PRESSURE (psi) Drilling Fluid Flow (GPM) 7 9 11 13 (off-bottom pressure) (PSI) 75 94 117 13 (on-bottom - off-bottom pressure) (PSI) 675 656 633 62 2 15 1 5 METRIC PERFORMANCE CURVES 4921 3785 347 265 2 4 DIFFERENTIAL PRESSURE (kpa) 25 2 15 1 5 TORQUE (N m) Drilling Fluid Flow (L/min) 265 347 4164 4921 (off-bottom pressure) (kpa) 517 648 87 896 (on-bottom - off-bottom pressure) (kpa) 4654 4523 4364 4275 147

9 5/8 (244 ) 5-6 5. Stage HR A. Distance to stabilizer B. Box to Bend C. Overall Length D. Thread Prot. Diameter E. Kick Pad Diameter 28 92 1.75 9.75 Imperial 711 2,337 42 1,211 273 248 Metric Top Connection Bottom Connection Weight Maximum Flow Rate Maximum Torque Maximum Power Maximum Weight Dynamic on bit Static Maximum Allowable Pull Pull to Yield Motor 5,365 1,3 24,17 768 6 5/8 Reg 179,3 551, 495, 1,53, AS PER REQUEST gpm ft- hp 2,386 4.921 32,77 573 6 5/8 Reg 79,7 245, 22, 681, m 3 /min N-m kw Bend Settings (degrees).26.52.78 1.3 1.27 1.5 1.72 1.93 2.12 2.3 2.6 2.82 2.95 3. Build Rate (degrees/1ft(3 m)) Hole Sizes (in, ) 12 1/4 13 3/4 17 1/2 311 375 445....23.. 1.89.. 3.92.. 5.87.. 7.74 1.26. 9.54 3.5. 11.25 4.76. 12.79 6.31. 14.26 7.78.64 16.71 1.22 3.8 18.5 12.1 4.88 19.56 13.7 5.93 19.97 13.48 6.34 148

9 5/8 (244 ) 5-6 5. Stage HR Maximum Pump Rate 1,3 gpm 4,92 Lpm Revolutions per unit volume.138 rev/gal.36 rev/l Pressure at full Load 1,13 psi 7,76 kpa Torque at full load 24,17 ft 24,17 N m 2 IMPERIAL PERFORMANCE CURVES 28 15 1 5 13 1 9 7 24 2 16 12 8 4 TORQUE (ft ) 5 1 DIFFERENTIAL PRESSURE (psi) Drilling Fluid Flow (GPM) 7 9 11 13 (offbottom pressure) (PSI) (on-bottom - off-bottom pressure) (PSI) 85 113 133 167 145 117 997 963 2 15 1 5 METRIC PERFORMANCE CURVES 4921 3785 347 265 2 4 6 8 DIFFERENTIAL PRESSURE (kpa) 35 3 25 2 15 1 5 TORQUE (N m) Drilling Fluid Flow (L/min) 265 347 4164 4921 (offbottom pressure) (kpa) (on-bottom - off-bottom pressure) (kpa) 586 779 917 1151 725 712 6874 664 149

9 5/8 (244 ) 6-7 5. Stage A. Distance to stabilizer B. Box to Bend C. Overall Length D. Thread Prot. Diameter E. Kick Pad Diameter 28 92 1.75 9.75 Imperial 711 2,337 378 9,61 273 248 Metric Top Connection Bottom Connection Weight Maximum Flow Rate Maximum Torque Maximum Power Maximum Weight Dynamic on bit Static Maximum Allowable Pull Pull to Yield Motor 5,144 1,2 13,32 543 6 5/8 Reg 179,3 551, 495, 1,53, AS PER REQUEST gpm ft- hp 2,288 4.54 18,35 45 6 5/8 Reg 79,7 245, 22, 681, m 3 /min N-m kw Bend Settings (degrees).26.52.78 1.3 1.27 1.5 1.72 1.93 2.12 2.3 2.6 2.82 2.95 3. Build Rate (degrees/1ft(3 m)) Hole Sizes (in, ) 12 1/4 13 3/4 17 1/2 311 375 445....24.. 1.83.. 3.82.. 5.74.61. 7.57 1.22. 9.33 2.98. 11. 4.65. 12.52 6.17. 13.96 7.6.61 16.35 1. 3.1 18.11 11.75 4.76 19.15 12.79 5.8 19.55 13.19 6.2 15