Application Manager User s Manual
Application Manager USER'S MANUAL
DATALOGIC S.p.A. Via Candini 2 40012 - Lippo di Calderara di Reno Bologna - Italy Application Manager Ed.: 07/2005 ALL RIGHTS RESERVED Datalogic reserves the right to make modifications or improvements without prior notification. Datalogic shall not be liable for technical or editorial errors or omissions contained herein, nor for incidental or consequential damages resulting from the use of this material. Product names mentioned herein are for identification purposes only and may be trademarks and or registered trademarks of their respective companies. Datalogic S.p.A. 2002 2005 22/07/05
CONTENTS 1 INTRODUCTION... 1 2 INSTALLATION... 3 2.1 Installing Application Manager... 3 2.2 Starting Application Manager... 4 3 CONFIGURATION... 5 3.1 Configuring Application Manager... 5 3.2 Configuration through DL Mobile Director local Configurator... 7 3.3 Switching between Telnet connection and HTTP connection... 8 iii
iv
INTRODUCTION 1 1 INTRODUCTION The Datalogic Application Manager is a desktop application for Windows CE.NET, allowing Datalogic Portable Data Terminals to run in Kiosk mode by selecting the application(s) to be published to the user. The Kiosk mode is a feature of the Kiosk information systems, the computer based terminals used to provide information or services, typically in public places, such as museums, libraries, airports, etc. When a system is run in Kiosk mode only one or few applications are available. If the autorun parameter is enabled, when the device is reset, the application is automatically re-started. In this way the terminal works as an application-specific device, not as a multi-purpose device. Datalogic Application Manager prevents the user from leaving the application and interacting with the operating system, or accessing the Task Bar or Start Menu. This feature is very important in Windows-based devices also to prevent users from changing terminal parameters. It is possible to exit the Application Manager to modify any necessary system setting by pressing the [ESC] key and entering a password. The main features are: Password protected exit (no password by default) Application selection, including Datalogic DL TCL-NET and Locked Web Browser (these Datalogic applications are set by default) TaskBar (terminal status bar) optionally visible TaskBar optionally enabled Start button optionally enabled Auto-run of Application Manager Auto-run of one single application 1
1 APPLICATION MANAGER When you launch Application Manager, the main window showing all the selected applications appears: Figure 1 Application Manager Main Window 2
INSTALLATION 2 2 INSTALLATION 2.1 INSTALLING APPLICATION MANAGER The Application Manager can be installed or upgraded through a PC installation process. This method is available only for Windows CE.NET devices connected to a PC. The installation program has to be run on the PC, in order to download the necessary files onto the Windows CE.NET device. To install the Application Manager by means of the PC installation method, follow the procedure below: 1. make sure that the Windows CE.NET device is connected to the PC and synchronized with it; 2. double-click the setup.exe icon on your PC and follow the instructions appearing in the dialog box below: Figure 2 Installation Dialog Box 3
2 APPLICATION MANAGER 2.2 STARTING APPLICATION MANAGER To start Application Manager, double tap the Application Manager icon available in the Connections folder on the desktop OR tap the Start button on the screen and select the Application Manager option from the Programs list. Figure 3 Where to Find Application Manager 4
CONFIGURATION 3 3 CONFIGURATION 3.1 CONFIGURING APPLICATION MANAGER To enter the configuration menu press the [ESC] key: a dialog box asking for a password will appear. By default there is no password, tap on the OK button. Figure 4 Password Dialog Box The following window will appear: Figure 5 Configuration Window 5
3 APPLICATION MANAGER In this window it is possible to set the following parameters: Taskbar visible If checked, the taskbar (terminal status bar) is visible. The icons giving information about the battery and keyboard status, the radio connection and the date and time are visible but cannot be accessed. Taskbar enable If checked, the taskbar is enabled (but the Start button is disabled). The icons can be accessed by tapping on them. Start enable If checked, the Start button is enabled. The user has access to the Programs list. Password This parameter allows defining the password to enter the configuration menu. Exit to CE.NET This button allows returning to Windows CE.NET. A complete configuration of all Application Manager parameters is possible only through Datalogic Mobile Director Local Configurator. 6
CONFIGURATION 3 3.2 CONFIGURATION THROUGH DL MOBILE DIRECTOR LOCAL CONFIGURATOR DL Mobile Director Local Configurator is a Windows-based utility tool allowing to configure and monitor a radio frequency network terminal. In particular, by selecting the Application Manager item in the Terminal Configuration node, a further sub-branch will appear allowing to configure the Application Manager parameters. Figure 6 Application Manager Branch 7
3 APPLICATION MANAGER 3.3 SWITCHING BETWEEN TELNET CONNECTION AND HTTP CONNECTION With Application Manager it is possible to switch between a Telnet connection and an HTTP connection by pressing a sequence of keys. In the following table, the key list available for this purpose: FROM TO TERMINALS KEYS Locked Web Browser DL-TCL-NET Datalogic-Jet, Viper-NET, Rhino-NET Locked Web Browser Application Manager Datalogic-Jet, Viper-NET, Rhino-NET F3 F2 DL-TCL-NET Locked Web Browser Datalogic-Jet Custom remapped keys (use the proper tools in DL Mobile Director Local Configurator in order to remap the keys for switching to Locked Web Browser ). Viper-NET, Rhino-NET ALT+L DL-TCL-NET Application Manager Datalogic-Jet Custom remapped keys (use the proper tools in DL Mobile Director Local Configurator in order to remap the keys for switching to Application Manager ). Viper-NET, Rhino-NET ALT+M 8