AC asynchronous and synchronous motors AC synchronous reluctance motors DC motors Hydro & Wind generators and more Power evolution
Power evolution AC asynchronous and synchronous motors AC synchronous reluctance motors DC motors Hydro & Wind generators and more SicmeProducts Electric Motors and generators for Industrial Applications Permanent Magnet Synchronous Generators for Renewable Energy Sicme Motori was founded in 1967 in Turin, Italy, to design and manufacture electric motors for industrial applications, up to a power of 2600kW, with focus on variable speed, and today ranks as one of the most important European players in the field of modern industrial drive motorisation. Since 2002 has also started the designing and manufacturing of permanent magnet synchronous generators for renewable energy up to 3MW (referred to 14rpm). SICMEMOTORI is an ISO 9001:2008 Company. SICMEMOTORI can satisfy most of the requirements when variable speed drives are requested. The Company itself is organised according to the principles of the Lean production and Learning Organisation, and makes wide use of integrated software systems. The production procedure is managed by a mrp system; all working processes are recorded by means of an up-dated laser bar-code reader system, which characterises all internal working methods, whilst maintaining total control of the entire manufacturing process. The company has two production facilities for the production of motors and generators, both located in Turin. The new testing department allows to test electric machines with power up to 3,5MW (referred to 14rpm) with the back-to-back configuration. Hoisting equipments are suitable to move and to load weights up to 120 tonnes.
HEAVY DUTY PUMP FANS RUBBER CEMENT PLASTIC OIL & GAS PAPER IRON & STEEL TEST STANDS WIND HOISTING Electric motors for industrial applications AC MOTORS FOR INVERTER SUPPLY High performances square frames: BQ Series Insulation and impregnation expressly designed for vector/inverter duty Power from 0,6 to 3600kW Shaft height from 80 to 500mm Fully laminated frame, with integrated ventilation system Degree of protection IP23 and IP54 (55/56) Low inertia and liquid cooled versions available (AJ/AW Series) Great choice of accessories Larger frames are available upon request IEC60034 and U.S. and Canadian UL High performance square frames with permanent magnets: SQ SJ Series Insulation and impregnation expressly designed for vector/inverter duty From 30 to 10000 Nm Shaft height from 100 to 355mm Fully laminated frame, with integrated ventilation system Designed and built to meet requests for high torque/high dynamic output required for modern production lines Low inertia, better efficiency and compact dimensions Rotor-stator option available Larger frames are available upon request IEC60034 Standard Synchronous reluctance motors without magnets: SR Series IPM motors option, best performace and flexibility (high flux weakening range) Power from 5 to 1500 kw No fundamental rotor losses, highest possible efficiency Suitable for all constant torque and constant power variable speed applications High dynamic behavior Very high overload, from zero speed to max flux weakening Synchronous, absolutely precise, even in sensorless operation Shaft height from 80 to 560 and higher Degree of protection IP23 and IP54-55
Original spare parts and service All most common electric motors spare parts: Brushes and brush-holders Bearings, brakes Blowers and filters Tacho generators and encoders Original motors spare parts such as commutators, shields, stators, rotors, coils, etc. Fast delivery all over the world Electric motors for industrial applications DC MOTORS For general purpose: P-NP Series Power from 0,5 to 2600kW Shaft height from 80 to 800mm Fully laminated frame All mounting arrangements and cooling systems available CSA certification and mark available NEMA Standards available For heavy duty: SM-ML Series Power up to 450kW Steel mill heavy duty motors SM802-804: steel fabricated, split frame ML806-818: fully laminated frame, not split, with compensating winding Ratings, specific operating features and outline dimensions according to AISE St. No. 1 revised Sept. 1968 Explosion proof: C Series Power from 0,16 to 35kW Supply voltage from 110 to 440V IIB + IIC certified by CESI EN60034 Standards, 94/9/EC (ATEX Directive) IEC-EX and EAC (ex Russia) available Solutions for traction systems: DC-AC Series For long/medium distance vehicles and tramlines Skyrail cableways, funicular railways Revision and repairing DC / AC MV Motors Coil windings production, stator and rotor rewind Supplies and service for the main european producers and users Power up to 700 kw
Direct-drive (or hybrid) solution advantages with permanent magnet synchronous motor/generator No gearbox: no lubrication required, no oil to dispose of Less mechanical components: less faults risks Virtually maintenance free: very low maintenance cost Very high efficiency Fast ROI Electric motors for industrial applications AC MOTORS FOR NON-STANDARD DUTY Synchronous and asynchronous motors Insulation and impregnation expressly designed for inverter duty Power up to 1000kW For railways auxiliary applications Marine propulsion duty IPM motors Rotor-Stator units Electric generators for renewable energy production PM SYNCHRONOUS GENERATORS SW Series Expressly designed for low speed or gearless applications ( Direct-Drive ) Special insulations and impregnation Catalogue power up to 450kW Nominal speed from 50 to 300rpm Totally enclosed not ventilated (IC410) Degree of protection IP54 (55) Nd-Fe-B high performances permanent magnets Special execution in co-project with Customers, power up to 6MW
Sicme Motori Srl Strada del Francese, 130-10156 Torino - Italy Tel: +39-011-4076311 - Fax: +39-011-4500047/4076439 www.sicmemotori.com - sicmemotori@sicmemotori.com