Tyfo Fibrwrap Blast Panels Prefabricated Blast Wall System
Tyfo Fibrwrap Blast Panels Prefabricated Blast Wall System DESCRIPTION Tyfo Fibrwrap Blast Panels are prefabricated composite walls comprised of the various Tyfo Fibrwrap Composite Systems. Typical panel dimensions are 10 feet wide and 12 feet tall with a panel thickness of 7.5 inches. Sizes do vary based on project-specific requirements. USE Tyfo Fibrwrap Blast Panels are unique, prefabricated composite walls. They are tested and custom designed to meet project-specific pressures and impulses associated with both accidental and terrorist explosions. Tyfo Fibrwrap Blast Panels can provide building envelope protection for blast mitigation or protection of interior space in industrial facilities. ADVANTAGES Does not use fiber reinforced concrete (FRC) or (ECC) Validated blast testing Prefabricated system Ease of installation Energy dissipating characteristics Mitigates high pressures and impulses Incorporates the rigorously tested Tyfo Fibrwrap Composites Fire tested per ASTM E119 * Weights and dimensions will vary based on the project parameters. MOMENT PLASTIC MOMENT FIRST YIELD TYPICAL BLAST PANEL CHARACTERISTICS & PROPERTIES PROPERTY Ultimate tensile strength in primary fiber direction, psi PERMANENT ROTATION MAXIMUM ROTATION INTERNAL STRAIN ENERGY ASTM METHOD SUPPORT ROTATION, θ TYPICAL TEST VALUE D-3039 83,400 psi (575 MPa) (4.17 kip/in. width) Pressure, (psi) 20 175 15 12.5 10 7.5 5 2.5 0 Pressure Impulse DESIGN VALUE 66,720 psi (460 MPa) (3.3 kip/in. width) Elongation at break D-3039 2.2% 1.76% Tensile Modulus, psi D-3039 3.79 x 10 6 psi (26.1 GPa) Typical Weight of Panel* Typical Dimensions* Design Pressures and Impulses 3.03 x 10 6 psi (20.9 GPa) 1,500 to 4,000 lbs. (680.39 to 1814.3 kg) 10 ft. x 12 ft. (3.05M x 3.66M) 5 psi to 30 psi / 80 to 300 psi - msec -2.5-30 -80-30 0 30 80 90 120 150 180 210 240 Time, (msec) 240 210 180 150 120 90 80 30 0 Impulse, (psi-ms) HOW TO USE TYFO Fibrwrap Blast Panels DESIGN The Tyfo Fibrwrap System shall be designed to meet specific design criteria. The criteria for each project is dictated by the engineer of record and any relevant building codes and/or guidelines. The design should be based on the allowable strain for each type of application and the design modulus of the material. The Fyfe Co. LLC engineering staff will provide preliminary design at no obligation. Test reports are available upon request. Fyfe Co. LLC Tyfo Fibrwrap Systems 8380 Miralani Drive, San Diego, CA 92126 Tel: 858.642.0694 Fax: 858.444.2982 E-mail: info@fyfeco.com www.fyfeco.com Statement of Responsibility: The technical information and application advice in this publication is based on the present state of our best scientific and practical knowledge. As the nature of the information herein is general, no assumption can be made as to the product s suitability for a particular use or application, and no warranty as to its accuracy, reliability or completeness, either expressed or implied, is given other than those required by State legislation. The owner, his representative or the contractor is responsible for checking the suitability of products for their intended use. Field service, where provided, does not constitute supervisory responsibility. Suggestions made by the Fyfe Co., either verbally or in writing, may be followed, modified or rejected by the owner, engineer or contractor since they, and not the Fyfe Co., are responsible for carrying out procedure appropriate to a specific application. 1/11 Fibrwrap Blast Panels Tyfo Systems are patented in U.S.A., Canada, and other countries. Copyright 2010-2011 Fyfe Co. LLC 6-11
TYFO BLAST panels Tyfo Blast Panel Systems are manufactured by Fyfe Co LLC. These blast resistance wall systems are comprised of steel studs sheathed with a thin cementitious wall reinforced with Tyfo Blast Glass and have typical wall thicknesses and weight. Shock tube testing has proven the system s ability to resist pressures up to 30 psi at an impulse of 135 psi-ms. This is equivalent to 750 Ibs. of TNT at 83 ft. After three consecutive tests, the permanent deformation was only 1-1/8 inch. They are easily constructed using conventional construction methods. The wall assembly can be easily finished with any type of material such as brick or stone. Tyfo Blast Panels are easy to install and can be finished with any type of material Tested in a shock tube, the blast-resistance wall system survived high pressures with limited deformations exhibited Interior of shock tube showing driver and expansion sections The blast-resistance capabilities of the prefabricated blast-resistant wall systems can be evaluated using pressure-impulse diagrams Also available - Prefabricated, Field Prefabricated or Super Concrete (Tyfocrete ), block and brick walls reinforced with Tyfo Fibrwrap.
TYFO BLAST panel MODELING The composite steel stud wall designs were analyzed based on a nonlinear dynamic Single-Degree-of-Freedom (SDOF) analytical methodology. The key output from the SDOF analysis is the peak dynamic deflection of the structural component. For most flexural components, it is convenient to convert this value into a support rotation, θ, by assuming a center-hinge deformed shape as is typically observed in plastic systems, and then applying simple geometric relationships. Using the dynamic enhanced material properties of the steel studs and concrete, a moment-curvature plot was produced to determine the moment capacity and stiffness of the wall panels. From this, the SDOF model parameters were calculated using one-way beam methods described in UFC 3-340- 02. These experimental results allow us to analytically predict the response of various shapes and sizes of wall design for our clients prior to committing to full-size testing. Equivalent Spring-Mass SDOF System Experimental vs Analytical Displacement Calculation of Support Rotation from Peak Deflection
FEDERAL AVIATION ADMINISTRATION (FAA) AIR TRAFFIC CONTROL TOWER (ATCT) Tyfo Blast Panels were utilized as a prefabricated energy absorbing exterior wall building system. The wall system was designed dynamically to resist the total blast overpressure. The wall system s dynamic design also considered the pressure/time function (impulse). The project required large-scale proof testing on a calibrated blast shock tube at pressures greater than 20 psi with an associated minimum impulse of 120 psi-msec. The blast panel size and shape were configured to meet project geometry requirements.
Mission Statement The mission of Fyfe Company is to provide state-of-the-art solutions for today s structural problems. Fyfe Company provides innovative construction products and personalized technical support to meet the needs of engineers, contractors and owners in the most efficient and cost-effective manner. Fyfe Company is committed to developing long-term relationships with our customers by providing the best possible technical assistance and delivering the most professional, up-to-date solutions through continuous research and innovation. For additional information, design assistance or questions about a potential project, please contact us... Fyfe Co. LLC Tyfo Fibrwrap Systems 8380 Miralani Drive, San Diego, CA 92126 Tel: 858.642.0694 Fax: 858.444.2982 E-mail: info@fyfeco.com www.fyfeco.com Fyfe Asia Pte. Ltd. 24 Sin Ming Lane, #03-106 Midview City Singapore 573960 Tel: +65.6898.5248 Fax: +65.6898.5181 Email: fyfeasia@singnet.com.sg www.fyfeasia.com Fyfe LatinAmerica Calle Los Bambues No. 16 Col. San Francisco San Salvador, El Salvador, C.A. Tel: +503.2223.6098 Fax: +503.2223.5865 Cell: +503.7039.1218 Email: erick@fyfe-la.com www.fyfe-la.com Fyfe (India) Pvt. Ltd. 226 Hammersmith Industrial Estate Narayan Pathare Marg Mahim (West), Mumbai 400016 India Tel: 91.22.6525.0236 Fax: 91.22.6525.0236 Cell: 91.98207.10224 Email: fyfeindia@vsnl.net Fyfe Europe S.A. 51 Ithakis Street & Kordeliou Glyfada, 16561 Athens, Greece Tel: +30.210.995.9595 Fax: +30.210.995.9965 Email: info@fyfe-europe.gr Contact Fyfe Europe S.A. for Europe, the Middle Eastern, the Russian Federation, and North Africa Fyfe (China) Pte. Ltd. Chengdu City 1st Ring Road East Section 5 No. 108 Dong Heng International No. 2 Bldg. Area 1 Unit 706 610066 People s Republic of China Tel: 86.28.6650.1560 Fax:86.28.6650.1562 Email: limboonkok@fyfeasia.com Fyfe Asia Pte. Ltd. (Shanghai Representative Office) No. 885 Renmin Road Unit 613 Huai Hai China Tower Huangpu District Shanghai 200010 China Tel: 86.21.6374.1773 Fax: 86.21.6374.1779 Email: limboonkok@fyfeasia.com www.fyfeasia.com Fyfe Korea Co. Ltd. #428-5, Songnae-dong, Kangdong-gu Seoul, 134-030, Korea Tel: 82.2478.6026 Fax: 82.2478.6024 E-mail: conclinic@conclinic.co.kr www.conclinic.co.kr Fyfe (Hong Kong) Ltd. Unit 5, 22/F Metropole Square 2 on Yiu Street Shatin Hong Kong S.A.R. Tel: 85.2.3579.5588 Fax: 85.2.3579.5599 Email: jwang@fyfe.com.hk Representatives available in over 50 countries around the world Patented in U.S.A., Canada, and other countries. Copyright 2011 Fyfe Co. LLC 171-11 Reproduction by written permission from Fyfe Co. LLC only. All rights reserved. Tyfo and Fibrwrap are registered trademarks for the products of Fyfe Co. LLC