Push Plate PUSH & PULL PLATES BHMA J301.050" thick Size TRM 1001 1 605 ------3 12 TRM 1001 1 613 ------3 12 TRM 1001 1 628 ------3 12 TRM 1001 1 630 ------3 12 TRM 1001 3 605 ------4 16 TRM 1001 3 609 ------4 16 TRM 1001 3 612 ------4 16 TRM 1001 3 613 ------4 16 TRM 1001 3 626 ------4 16 TRM 1001 3 628 ------4 16 TRM 1001 3 629 ------4 16 TRM 1001 3 630 ------4 16 Other sizes and finishes available F/O DOOR PULLS Round door pulls are available in different diameters and centers, both straight projection and offset. There are also many different methods of fastening available. Specifications necessary include size and center to center dimensions, fastening method (including whether or not they are to be mounted back to back) as well as thickness and material of the door. Please speak to our sales professionals who can fill you in on all the details needed to order. Two of the most commonly requested pulls are: Door Grip Flush Cup Pull Spec: J403 Extruded Stainless Steel Size: 3 1 /2 4 3 /4" Depth: 13 /16" TRM 1115 630 Door Pulls Door Pull Plate ADA Other sizes and finishes available F/O 4 16" 1 7 /8" Projection Grip 1117 1 1 1 /2" Clearance 5" Center to Center BHMA J405.050" thick TRM 1010 3 605 TRM 1010 3 612 TRM 1010 3 613 TRM 1010 3 625 TRM 1010 3 626 TRM 1010 3 628 TRM 1010 3 629 TRM 1010 3 630 TRM1194 TRM 1191 TRM 1194 4 630 Center to Dia. Center E Mounting, Straight --------- 3 /4" --------12" Projecting Pull TRM 1191 4 630 E Mounting, Offset-------------1" ---------12" Projecting pull E mounting is a through bolt with a finishing washer not intended for glass doors. Offset Entrance Door Pulls 3 1 /2 11 3 /8" overall Material 628 Pull 628 Insert 2 7 /8" Projection 10" Center to Center Brackets A TRM 9560 628 TRM 9563 313 (628 Insert) TRM 1102S TRM 1102T Spec: J401 Overall Height: 7 1 /2" Projection; 2 3 /16" Clearance: 1 1 /2" Center to Center: 5 1 /2" Surface Mount Pull TRM 1102S 605 TRM 1102S 626 Thru Bolt Door Pull Same specifications as 1102S, only with thru bolted fastening. F/O TRM 1102T 613 TRM 1102T 626 Hospital Door Pull Spec: J401 5" center to center 9 1 /16" Overall length 3 1 /2" Projection Cast Brass 2" Clearance wood screws TRM 1134 626 PHONE: 800 745 5450 FAX: 800 876 5397 1
ACCESSORY HARDWARE Sliding Door Locks & Pulls These combination sliding door locks and pulls are simple to install. Just a simple mortise cutout in the door, slide the factory assembled unit into place and tighten two screws. All units fully reversible For 1 3 /8" doors Available for 1 3 /4" thick doors on F/O Plates are solid brass bronze Sliding Door Pull Spec: D08021 Wrought Brass /Bronze (2) #6 1 /2" wood screws For use on passage doors TRM 1064 605 625 TRM 1064 605 TRM 1064 609 TRM 1064 612 TRM 1064 613 TRM 1064 625 TRM 1064 626 Sliding Door Privacy Lock Spec: D08031 Wrought Brass/Bronze (2) #6 1 /2" wood screws, and (2) #5 3 /4" wood screws For use on bathroom and bedroom doors TRM 1065 605 625 TRM 1065 605 TRM 1065 609 TRM 1065 612 F/O TRM 1065 613 TRM 1065 625 TRM 1065 626 Universal Dome Stop No more need for high or low dome stops 7 /32" Rise 1 1 /2" Base 1 7 /16" Height Material Cast BHMA LO2141 Low Rise Lip and High Rise Rubber enable this stop to be used with door openings either with or without threshold. No adapters necessary. May be used with 1210 Carpet Risers (#1210AR), although need for risers is substantially reduced. TRM 1211 605 -------Universal Dome Stop TRM 1211 612 -------Universal Dome Stop TRM 1211 613 -------Universal Dome Stop TRM 1211 625 -------Universal Dome Stop TRM 1211 626 -------Universal Dome Stop Adapter Riser 1 3 /4" Diameter 15 /32" Height TRM 1210AR 613 F/O ----Adapter Riser TRM 1210AR 626 F/O ----Adapter Riser Door Holder Cast 1 3 /8 2" Base 5 25 /32" Height Finish Full Finish BHMA LO1391 TRM 1220 5 605 TRM 1220 5 612 TRM 1220 5 613 TRM 1220 5 625 TRM 1220 5 626 Rubber Shoe TRM 1220 RBR-------Rubber Shoe Only Rubber shoes for old Quality 1149 door holder:trm 1149BS STOPS and Holder 1 3 /8 2" Base 4 27 /32" Height Finish Sprayed Aluminum BHMA LO1381 TRM 1221 4 628 Convex Wall Bumper Cast TRM 1270CX 612 TRM 1270CX 613 TRM 1270CX 626 1 3 /8" Inside Dia. 2 3 /16" Outside Dia. 1" Projection Material Cast BHMA LO2251 Wrought TRM 1270WX 605 TRM 1270WX 630 Packed with a wood screw, rawl plug,plastic toggler, machine screw, lead anchor and metal toggle bolt. Concave Wall Bumper Part No. Cast TRM 1270CV 612 TRM 1270CV 613 TRM 1270CV 625 TRM 1270CV 626 TRM 1270CV 626 1 3 /8" Inside Dia. 2 3 /16" Outside Dia. 1" Projection BHMA LO2251 Wrought TRM 1270WV 613 TRM 1270WV 630 Packed with a wood screw, rawl plug,plastic toggler, machine screw, lead anchor and metal toggle bolt. 2 WHOLESALE HARDWARE & LOCKSMITHS SUPPLIES
DOOR STOPS, HOLDERS & BUMPERS & Holder & Holder Base Stop TRM 1206 TRM 1207 L01341 (1206) and L01 351 (1207) No. 1206: (5) #8 1" wood screws No. 1207: (1) 15 /16 2 1 /2" stud with expansion shield and (3) #8 1" wood screws and anchors TRM 1206 613 TRM 1207 613 TRM 1206 626 TRM 1207 626 TRM 1204 TRM 1205 L02011 (1204) and L02021 (1205) No. 1204: (3) #8 1" wood screws No. 1205: 5 /16 2 1 /2" stud with expansion shield and (1) #8 1" wood screw and plastic anchor TRM 1204 612 TRM 1205 612 TRM 1204 613 TRM 1205 613 TRM 1204 626 TRM 1205 626 TRM 1223 TRM 1224 Height: 3 5 /8" Spec: BHMA #L01361 (QUA 39) and L01371 (QUA 139) No. 1223: (5) #8 1" wood screws No. 1224: (1) 5 /16" 2 1 /2" stud with expansion shield and (3) #8 1" wood screws with plastic anchors TRM 1223 613 TRM 1223 626 TRM 1224 613 TRM 1224 626 Door & Floor Stops TRM 1200 TRM 1201 Height: 3" Spec: BHMA #L02121 (1200) and L02131 (1201) No. 1200: (3) #8 1" wood screws No. 1201 5 /16 2 1 /2" stud with expansion shield and (1) #8 1" wood screw and plastic anchor TRM 1200 612 TRM 1200 613 TRM 1200 626 TRM 1201 612 TRM 1201 613 TRM 1201 626 Base: 1 3 /16" diameter Spec: BHMA #L02031 Supplied with #8 1" hangar bolt TRM 1208 605 TRM 1208 613 TRM 1208 626 Height: 2" Base: 1 5 /8" 2 1 /2" 02181 Cast Supplied with combo pack fasteners TRM 1231 626 TRM 1233 612 TRM 1233 626 Door Holder TRM 1254 612 TRM 1254 613 TRM 1254 626 Height: 2 7 /8" Base: 1 3 /8 2 3 /4" L02 181 Cast Overall Size: 2 3 /4 2 1 /2" Strike Base: 1" 2" Strike Projection: 2 1 /8" L01291 Cast PHONE: 800 745 5450 FAX: 800 876 5397 3
Door Holders For use on doors without threshold. L01301 Cast Door to floor clearance of 1 /2" or less TRM 1261 612 TRM 1261 613 TRM 1261 626 Door Holder 1263 L01301 Door to Floor Clearance of 9 /16" to 1 1 /16" TRM 1263 613 TRM 1263 626 Door Holder 1267 L01301 Cast Brass Door to Floor Clearance of: 1 5 /8" to 2 1 /6" TRM 1267 626 DOOR PROTECTION Metal and Plastic Kick Plates Kick plates are used at the bottom of a wood or metal door subject to marring or damage due to foot traffic. Stocked in.050 thickness. All edges are relieved. Sizes shown are stocked, other sizes from 7 to 16 inches in height are available on Factory Order. Individually packaged with screws. Special finishes, heavy bevel edges and.038 thickness available on F/O. Base Finish Material TRM K0050 10 28 612 ---Satin Brz-----Bronze TRM K0050 10 28 630 ---Satin SS -----S Steel TRM K0050 10 30 630 ---Satin SS -----S Steel TRM K0050 10 34 605---Pol. Brass -----Brass TRM K0050 10 34 613 -----Oil Rbd Brz-----Bronze TRM K0050 10 34 630 ---Satin SS -----S Steel Plastic Kick Plate 1/4" thick, stocked in size and color listed. Available in many other colors and sizes from 4 to 48" high on Factory Order. Individually packaged with screws. TRM K6000 10 34 Brown Armor plates Armor plates are used in the same way as kick plates. They are necessary when protection is required higher than 16" on the door, such as when larger carts are used to open a door. All edges are relieved, made of aluminum, brass, bronze or stainless steel. Dimensions: 17 to 48" high,.050 or.038 thick, all available on F/O. Height Thickness TRM KA050 1 ----------17 24"------------.050 TRM KA050 2 ----------25 48"------------.050 TRM KA038 ------------17 48"------------.038 Mop plates Mop plates are used at the bottom of a wood or metal door subject to marring or damage due to cleaning operations and are 6" or under in height. All edges are relieved. Made of aluminum, brass, bronze or stainless steel. Specify finish. Not stocked, available on F/O. Thickness TRM KMO50 -------------.050 TRM KMO38 -------------.038 Stretcher Plates Stretcher plates are used at the middle of a wood or metal door subject to marring or damage from stretchers or service carts. Beveled on four edges. Six inches high,.050 thickness. Made of aluminum, brass, bronze or stainless steel. Specify finish. Not stocked, Available on Factory Order. TRM KS050 Latch Protector Protects the latch from vandalism and forced entry. Installs in minutes. Designed to fit all American made cylindrical locks. Heavy duty stainless steel construction. Available in both 4" and 6" vertical measure. Stocked in satin stainless steel, other finishes available on F/O. TRM 1082 4 630-----4" Cylindrical Lock Guard TRM 1082 6 630-----6" Cylindrical Lock Guard Latch Protector Lock Astragal Cast for Cylindrical lock 6 1 9 /16" 4" Center to Center 13 ga. Stainless Steel TRM 5002 630 4 WHOLESALE HARDWARE & LOCKSMITHS SUPPLIES
BOLTS & LATCHES Flush Extension Bolt Coordinator 1 6 3 /4" 11 /16" Throw 12" Rod Extruded BHMA L04081 UL Listed TRM 3917 12 613 TRM 3917 12 626 Cast Drop Arm Type Two nylon rollers and set screw adjustment standard UL Listed 2 5 /16 6 9 /16" BHMA 41.1 Type 25 TRM 3093 612 TRM 3093 613 TRM 3093 626 Mitey Lok SURFACE/FLUSH BOLTS Surface Bolts Spec: L04151 Extruded Brass Supplied with mortise and rim strikes These neat, modern solid brass bolts feature: Concealed screw installation No bands across the face to mar or scratch the bolt surface Tension spring action to hold the throw bolt solidly in position A perfect acting bolt every time because of its interlocking construction which also adds strength and durability The installation is simple and easy no fussing with tools and waste of time in fitting and adjusting Length Throw TRM 4873 605 ------------3"---------------- 5 /8" TRM 4873 609 ------------3"---------------- 5 /8" TRM 4873 626 ------------3"---------------- 5 /8" TRM 4874 605 ------------4"---------------- 7 /8" TRM 4874 613 ------------4"---------------- 7 /8" TRM 4874 626 ------------4"---------------- 7 /8" TRM 4876 605 ------------6"-----------------1" TRM 4876 609 ------------6"-----------------1" TRM 4876 613 ------------6"-----------------1" TRM 4876 626 ------------6"-----------------1" TRM 4882 626 F/O------12" --------------2 1 /4" DOOR & CABINET HARDWARE Mail Drop Extruded aluminum mail slots with aluminite finish. For use with 1 /4" plate glass, no mounting screws required. Simple installation. All of the mechanism is concealed. Fully reversible for door or side light OA size is 2 9 /16 9 15 /16". Glass cut out is 2 3 /8 9 3 /8". Opening size is 1 11 /16 9". TRM 1101 628 Classic Door Grille Knocker outside, hinged door inside. Interior thru bolt mounted. 3 1 /4 6 1 /8" Cast TRM 912 605 Coat & Hat Hook TRM ML2 TRM ML4 For use on sliding windows or doors. Aluminum, bright finish. Hardened steel bolt. Self tapping screws supplied. Measures 1 3 /8 2 1 /2"; 5 /8" throw. Mitey Lok is available with key control. Children can t unlock door. Same specifications as above, plus disc tumbler cylinder. Spec: L0311 1 Base: 1 5 /8 1 3 /8" Projection: 3" Material: Cast Brass (2) #6 5 /8" wood screws TRM 3070 1 626 PHONE: 800 745 5450 FAX: 800 876 5397 5