D-Show Profile Hardware Accessories Installation Guide For VENUE D-Show Profile Systems Assembling and Attaching the Video Monitor Mount to D-Show Profile D-Show Profile includes a Video Monitor Mount for your VGA monitor. Follow the instructions in this section to attach your video monitor to the mounting hardware. Assembling the Video Monitor Mount requires the following items: A VGA flat panel display with 100mm or 75mm mounting compatibility A medium sized Phillips screwdriver A table or similar clear, flat area with a towel or other padded surface (big enough to safely lay your video monitor face down) Assembling the Video Monitor Mount The Video Monitor Mount is assembled by attaching a flat panel VGA monitor to the mounting arm. Both the 100mm and 75mm VESA (FDMI) video mounting standards are supported. To assemble the Video Monitor Mount: 1 Remove the Video Monitor Mount components from their packaging. Components include two T-bolts, two knurled locking nuts, the mounting arm, a, an additional mounting plate (for 100mm monitors only), and. 3 Attach your monitor to the Video Monitor Mount by doing either of the following, as appropriate for your video monitor: 100mm (MIS-D100) Attach the to the included mounting plate using the provided hardware. To complete the assembly, remove the 4 mounting from the back of the video monitor, line up the holes of the mounting plate, and use the you removed to secure the plate to the back of your monitor. back front Attaching a 100mm VGA monitor to the mounting plate, and mounting arm, viewed from the top edge of the monitor 75mm (MIS-D 75) Use the included. Remove the appropriate from the back of your monitor and use them to secure the to the back of the monitor. back front Mounting arm (top) Mounting plate Video monitor Mounting arm Video monitor Attaching a 75 VGA monitor to the and mounting arm, viewed from the top edge of the monitor 4 Hold the mounting arm face down so that the narrow (top) end is against the back of the. Make sure the arm is facing the correct way, and attach the arm to the using the four provided. Mounting Arm (top) 5 Make sure all are tightened securely before attaching the assembled video mount to the console. Components of the Video Monitor Mount T-bolt (2) Locking Nut (2) 2 Make sure your video monitor is powered off and disconnected, and lay it face down on a padded table. D-Show Profile Hardware Accessories Installation Guide 1
Attaching the Video Monitor Mount to D-Show Profile To attach the Video Monitor Mount to the console: 1 From the back of the console, locate the Video Mount slot below the edge of the outermost back panel extrusion. 2 Take one of the T-bolts included with the Video Mount and insert it into the wider opening at the far left end of the Video Mount slot. Slide the T-bolt to the right along the slot until it stays in the track. Removing and Attaching the Video Monitor Mount To remove the Video Monitor Mount: 1 Stand at the back of the console. 2 Holding the VGA screen in one hand, loosen the lock nuts that secure the Video Monitor Mount to the extrusion on the back of the console. 3 Slide the Video Monitor Mount straight back off the T-bolts. 4 Tighten the lock nuts to secure the T-bolts and locking nuts in place. To attach the assembled Video Monitor Mount to the console: Video Mount slot Location of the Video Mount slot 3 Take the second T-bolt, insert it into the opening at the left and slide it to be a few inches away from the first T-bolt. 4 Take the two silver lock nuts (thumb nuts) and thread them loosely onto the T-bolts (do not tighten them). 1 Loosen the two lock nuts securing the T-bolts in place, along the extrusion at the back of the console. 2 Position the Video Monitor Mount so that its base slots line up with the T-bolts, and slide the Video Monitor Mount into position. 3 Tighten the lock nuts to secure the mount into place. 5 Pick up the assembled Video Monitor Mount and hold it at the bottom of the VGA monitor, so you can balance the unit with one hand. 6 Position the base of the video mount under the back panel extrusion and feed the T-bolts through the two slots on the front edge of the arm assembly. Loosen the lock nuts if necessary. 7 Tighten the lock nuts thumb nuts to secure the Video Monitor Mount in position. To move the monitor left or right: 1 Loosen the thumb nuts slightly. 2 Slide the Video Monitor Mount to the left or right, being carefully not to twist it off either of the T-bolts. (If the mount comes off the T-bolts, simply reattach it and resume). 3 When in the desired position, tighten the lock nuts. To adjust the height of the monitor: 1 Determine the desired height and mark the location on the mounting arm. 2 Detach the Video Monitor Mount from the console (see Removing and Attaching the Video Monitor Mount on page 2). 3 Loosen the holding monitor (or the ) to the mounting arm, and slide it down or up to the desired height. 4 Tighten all to secure the monitor in its new position. D-Show Profile Hardware Accessories Installation Guide 2
Assembling and Attaching the Trackball Mount to D-Show Profile The Trackball Mount can be placed anywhere along the front edge of the console to provide a tray for your trackball or a mouse that accommodates left- or right-handed operation. A small hook underneath the Trackball mount lets you hang a pair of headphones. Assembling the Trackball Mount To attach the Trackball Mount 1 Unpack the Trackball Mount and components from their packaging. 2 Make sure to unplug any USB or headphone connections at the front of the console. 3 From the front of the console, locate the slot for the Trackball mount (located below the extrusion). 4 Take one of the T-bolts included with the Trackball Mount and insert it into the opening at the right end of the Trackball Mount slot. Slide the T-bolt to the left along the slot until it is just to the left of the front panel USB and headphone ports. 5 Take the second T-bolt, insert it into the opening at the right and slide it into place a few inches away from the first T-bolt. Removing and Attaching the Trackball Mount The Trackball Mount can be removed quickly before packing or storing the console. Always disconnect USB and headphones from the front panel ports before removing or attaching the Trackball Mount. To remove the Video Monitor Mount: 1 Holding the Trackball Mount in one hand, loosen the lock nuts that secure it to the front of the console. 2 Drop the Trackball Mount off track to remove the entire assembly from the console. 3 Replace the lock nuts onto the T-bolts and tighten them down, to secure them in place. To attach the assembled Trackball Mount to the console: 1 Loosen the two lock nuts securing the T-bolts in place, along the extrusion at the front of the console. 2 Position the Trackball Mount so that its base slots line up with the T-bolts, and slide the Trackball Mount into position. 3 Tighten the lock nuts to secure the mount into place. 6 Take the two silver lock nuts (thumb nuts) and thread them loosely onto the T-bolts (do not tighten them). 7 Place the Trackball Mount in position so that you can feed the T-bolts through the two slots on the lip of the Trackball Mount. 8 Move the Mount and T-bolts left or right to line up the opening in the mount with the front panel USB and Headphone ports. 9 Tighten the lock nuts to secure the assembled Trackball Mount to the console. 10 Reconnect USB and headphones to the front panel ports. Copyright 2007 Digidesign, a division of Avid Technology, Inc. All rights reserved. This guide may not be duplicated in whole or in part without the express written consent of Digidesign. Avid, Digidesign, D-Show, and Pro Tools are either trademarks or registered trademarks of Avid Technology, Inc. in the US and other countries. All other trademarks contained herein are the property of their respective owners. Product features, specifications, system requirements, and availability are subject to change without notice. PN 9340-57169-00 REV A 07/07 D-Show Profile Hardware Accessories Installation Guide 3
www.digidesign.com DIGIDESIGN 2001 Junipero Serra Boulevard Daly City, CA 94014-3886 USA Tel: 650.731.6300 Fax: 650.731.6399 TECHNICAL SUPPORT (USA) Tel: 650.731.6100 Fax: 650.731.6384 PRODUCT INFORMATION (USA) Tel: 800.333.2137 INTERNATIONAL OFFICES Visit the Digidesign website for contact information