EN54-16 Voice Alarm System PRODUCT DATASHEETS

EN54-16 Voice Alarm System PRODUCT DATASHEETS

WayGuard This page is intentionally left blank Pagina 2 di 16

WayGuard Revision history Rel. Data Autore Modifiche 1.00 25/02/15 First emission Pagina 3 di 16

WayGuard This page is intentionally left blank Pagina 4 di 16

WayGuard FOREWORD The Wayguard is a certified EN54-16 voice alarm audio system that is intended to be used in applications where voice evacuation and general public address is needed. The system is configurable upon the layout of the building where it will be installed thanks to its extreme flexibility. Its units and sub-systems allow to setup configuration that will manage up to 108 zones and up to 108 microphone stations. The system can forward recorded alarm messages to dedicated zones. Each zone has two independent and dedicated messages. All signal and data paths are monitored according to the requirements of the EN54-16 regulation. The configuration of the system is made through a dedicated PC software. MAIN FEATURES AND FUNCTIONALITIES Voice alarm sound system configurable from 1 to 108 zones Independent controller for each zome Two dedicated recorded messages for each zone Monitored trigger contacts for alarm messages Continuous and independent monitoring of power amplifiers and loudspeaker lines, including ground fault No loudspeaker line termination is needed Initial calibration of loudspeaker lines and power amplifiers Spare amplifier connections on master and slave units Independent volume and tone control for each zone Independent volume and tone control for each audio program, spoken or recorded Background music input Up to 108 microphone station management. Each microphone station can be configured for voice alarm or for general announcements. Continuous monitoring of audio patch and mic. capsule on each microphone station Operation through 3 password protected access levels Manual silencing over each zone Internal events log list Dry contacts for system status monitoring Extension slots for future uses and system upgrades. TYPICAL APPLICATIONS Shopping malls Hospitals Railway stations Airports Museums Schools Stadiums Office buildings Pagina 5 di 16

WayGuard WG-MSU05 Master Unit WG-MSU05 front panel view 5 WG-MSU05 rear panel view 6 7 8 9 10 11 12 13 14 15 16 17 1. Graphic LCD display. 2. Navigation keyboars 3. Status LEDS: POWER indicates that the unit is powered, VOICE ALARM indicates that the system is forwarding a voice alarm messages, FAULT indicates there is a fault in some part of the equipment. 4. USB port for configuration download. 5. Zone module slots (WG-LMM01, WG-LRM01) 6. Monitored triggers for alarm messages activation 7. Dry contact indicates that the system is forwarding a voice alarm message. 8. Dry contact indicates that the system is forwarding a general announcement. 9. Slot dedicated to future uses 10. Ground connection 11. Dry contact inputs for power supply status reporting 12. Dry contact indicats a fault 13. Background music input 14. Bus 0 and Bus 1 to microphone stations 15. Connections to WG-ESU08 slave units 16. Spare amplifier connections 17. 24Vdc power input Pagina 6 di 16

WayGuard WG-MSU05 TECHNICAL SPECIFICATIONS : Steel enclosure, rack mountable with extensions slots on back panel IP protection according to EN 50102: IP30IK4 Dimensioni: Weight: User interface on front panel W:19 H: 2U D: 195,5mm 4,10 Kg 6x navigation keys, graphic 160x64 LCD display, 3x status leds USB Device port Power Input voltage Power: Power distribution +24Vdc (min 22Vdc, max 28Vdc) 2,64W (110mA @ 24Vdc) measurement condition: quiescent state, all slots empty, no mic station connected 2x 24Vdc bypass - max 1,5A on each microphone bus Modularity and extension slots Zone controllers Extension slots Extension ports 5x slots 1x slot general-purpose 2x RJ45 to WG-ESU08 units Audio inputs Microphone stations busses Background music inputs Digital audio player Balanced, 600 ohm, freq. fesponse 250 18.000Hz @-3dB, 2Vpk max, S/N >80dB RS485 databus +24V power supply, 1,5A max Stereo RCA, mixed to mono. Freq. response 60 18.000Hz, 1.8Vpk max signal.s/n S/N >80dB 12bit, 32Khz, storage files audio on Secure Digital card Audio paths management Architecture Volume control: Bass, mid, treble control 4 to 108 matrix arrangement -50dB 0dB -14dB +14dB Spare amplifier connection Description Automatic management and automatic switchover in case of main amplifier failures Continuous supervision Output to spare amplifier Balanced, transformer coupled, 600Ω 1.20Vrms, S/N >80dB, THD <1% Input from spare amplifier Spare amplifier monitoring 100V line, max power: 500Wrms analysis on 1 Khz tone burst Input triggers and dry contacts Player control (EVAC) Output dry contacts 2x inputs, with short circuit and cable-cut monitoring Busy (NC) Alarm (NO) Falul (NC/NO) Pagina 7 di 16

WayGuard WG-ESU08 Slave Unit WG-ESU08 front panel view WG-ESU08 rear panel view 2 3 4 5 6 1. Status LEDs: POWER indicates that the unit is powered, FAULT indicates there is a fault 2. Zone modules slots (WG-LMM01, WG-LRM01) 3. Ground connection 4. Chain connection from WG-MSU05 and to other WG-ESU08 units. 5. Spare amplifier connections 6. 24Vdc power inputs WG-ESU08 TECHNICAL SPECIFICATIONS Steel enclosure, rack mountable with extensions slots on back panel IP protection according to EN 50102: IP30IK4 Dimensions: Weight: User interface on front panel W:19 H: 2U D: 195,5mm 3,90 Kg 2x status leds Power Input voltage Power: +24Vdc (min 22Vdc, max 28Vdc) 1.3W (55mA @ 24Vdc) measurement condition: quiescent state, all slots empty, no mic station connected Modularity and extension slots Zone controllers 8x slots Spare amplifier connection Output to spare amplifier Balanced, transformer coupled, 600Ω 1.20Vrms, S/N >80dB, THD <1% Input from spare amplifier Spare amplifier monitoring 100V line, max power: 500Wrms analysis on 1Khz tone burst Output to spare amplifier Bilance, trans forme coupled, 600Ω 1.20Vrms, S/N >80dB, THD <1% Pagina 8 di 16

WayGuard WG-LMM01 Zone and Amplifier Controller WG-LMM01 connections view 1 2 1. LED BUSY : indicates the line is busy 2. LED FAULT : indicates a fault condition 3. Dry contact inputs; message triggers. Inputs have continuous monitoring against cable cut and cable short 4. Balanced output to power amplifier 5. 100V input from amplifier 6. 100V output to loudspeaker line 3 4 5 6 WG-LMM01 TECHNICAL SPECIFICATIONS Dimensions: Weight: Open frame mountable on WG-MSU05 o WG-ESU08. 85x35x125mm 0,18 Kg Zone amplifier management Description: Power The unit manages the zone amplifier and its loudspeaker line. In case of power amplifier 9alance, the unit calls for automatic switchover the spare 9alanced9, if installed. 0.72W (30mA @24Vdc) quiescent state Line output: Balanced transformer coupled, 600Ω 1.20Vrms, S/N >80dB, THD <1% Input from amplifier Amplifier monitoring 100V, max 500Wrms 18Khz tone burst, FFT analysis, 5% voltage tolerance from initial calibration Loudspeaker line Oputput Line monitoring 100V, max 500Wrms 18Khz tone burst, FFT analysis, 5% impedance tolerance PLAYER DIGITALE Digital audio player Onboard memory Player control (EVAC) 12bit, 32Khz, storage files audio on Secure Digital card Allows to store 2x 1 minute message 2x inputs, with short circuit and cable-cut monitoring Pagina 9 di 16

WayGuard WG-LRM01 Zone B Controller WG-LRM01 connections view 1 2 1. LED BUSY : indicates the line is busy 2. LED FAULT : indicates a falult on the line 3. 100V input from mani amplifier 4. 100V output to loudspeaker line 3 4 WG-LMM01 TECHNICAL SPECIFICATIONS Dimensions: Weight: Open frame mountable on WG-MSU05 o WG-ESU08. 85x35x125mm 0,11 Kg Line B management (matched to WG-LMM01) Description Power The unit performs the monitoring of the B line and has to be marched to the WG-LMM01 module, sharing the same power amplifier. 0.67W (30mA @24Vdc) quiescent state Loudspeaker line Oputput Line monitoring 100V, max 500Wrms 18Khz tone burst, FFT analysis, 5% impedance tolerance Pagina 10 di 16

WayGuard WG-MTU01 WG-MTU01 WG-MTU10 Microphone Stations Connections view, common to all models 1. Bus connection to WG-MSU05 2. Auxiliary 24V power input (not for emergengy mic stations) 2 1 1. Status LEDs 2. Push to talk button WG-MTU01 top panel view 1. Status LEDs 2. Push to talk button 3. Configurable keyboard WG-MTU06 top panel view 1. Status LEDs 2. Quick select message keys 3. LCD graphic display 4. Push to talk button 5. Configurable dial keyboard 6. Clear key 7. Background music key WG-MTU10 top panel view Pagina 11 di 16

WayGuard WG-MTU01 TECHNICAL SPECIFICATIONS Powder coated chassis, brushed and anodized aluminium top panel. EN 50102 IP protection class: IP31IK4 Dimensions Weight: Description Frequency response: Power Connection Microphtone capsule monitoring User interface 140x190x50mm gooseneck length 330mm 1,05 Kg Emergency or general announcement microphone station, embedded audio compressor, continous minitoring of microphone capusle with fault reporting 250Hz 12Khz @ -3dB S/N >80dB 1,2W (50mA @ 24Vdc) quiescent condition RJ45 plug to WG-MSU05. Monitored audio and data paths Short circuit open circuit 1x pushbutton key 2x leds WG-MTU06 TECHNICAL SPECIFICATIONS Powder coated chassis, brushed and anodized aluminium top panel. EN 50102 IP protection class: IP31IK4 Dimensions Weight: Description Frequency response: Power Connection Microphtone capsule monitoring User interface 225x190x50mm gooseneck length 330mm 1,35 Kg Emergency or general announcement microphone station, embedded audio compressor, continous minitoring of microphone capusle with fault reporting 250Hz 12Khz @ -3dB S/N >80dB 1,2W (50mA @ 24Vdc) quiescent condition RJ45 plug to WG-MSU05. Monitored audio and data paths Short circuit open circuit 7x pushbutton keys 16x leds Pagina 12 di 16

WayGuard WG-MTU10 TECHNICAL SPECIFICATIONS Powder coated chassis, brushed and anodized aluminium top panel. EN 50102 IP protection class: IP31IK4 Dimensions Weight: Description Frequency response: Power Connection Microphtone capsule monitoring User interface 240x190x50mm gooseneck length 330mm 1,45 Kg Emergency or general announcement microphone station, embedded audio compressor, continous minitoring of microphone capusle with fault reporting 250Hz 12Khz @ -3dB S/N >80dB 1,2W (50mA @ 24Vdc) quiescent condition RJ45 plug to WG-MSU05. Monitored audio and data paths Short circuit open circuit 16x pushbutton keys 6x leds graphic 160x64 LCD display Pagina 13 di 16

WayGuard WG-DPA241 WG-DPA501 WG-DPA242 WG-DPA124 Power Amplifiers Series 1. Channel volume control 2. Signal indicator 3. Clip Indicator 4. Protection indicator 5. Power switch 6. Power indicator WG-DPAxx series front panel, common to all model except nr of channels 7. Mains power input 8. 24V input (one for each channel) 9. Cooling fan 10. Loudspeaker 100V output 11. Balanced input 12. RJ45 reserved for future use WG-DPAxx series frear panel, common to all model except nr of channels WG DPA241 TECHNICAL SPECIFICATIONS Rated output power Loudspeaker output Input sensitivity Input impedance Frequency response S/N ratio Controls Indicators Protection Power consmption Power supply dimensions Weight Single channel 240W power amplifier 240W rms 100V line +/- 385mV balanced input 20 Kohm 80Hz 18Khz (+1dB, -3dB) >85dB Volume control on front panel Power, signal presence, overload, protection High temp, overload, short circuit 248W 220Vac 50Hz ; 24Vdc 484x380mm; 1U 3,8Kg Powder coated chassis, brushed and anodized aluminium front panel. EN 50102 IP protection class: IP31IK4 Pagina 14 di 16

WayGuard WG DPA501 TECHNICAL SPECIFICATIONS Rated output power Loudspeaker output Input sensitivity Input impedance Frequency response S/N ratio Controls Indicators Protection Power consmption Power supply dimensions Weight Single channel 500W power amplifier 500W rms 100V line +/- 385mV balanced input 20 Kohm 80Hz 18Khz (+1dB, -3dB) >85dB Volume control on front panel Power, signal presence, overload, protection High temp, overload, short circuit 515W 220Vac 50Hz ; 24Vdc 484x380mm; 1U 3,8Kg Powder coated chassis, brushed and anodized aluminium front panel. EN 50102 IP protection class: IP31IK4 WG DPA242 TECHNICALSPECIFICATIONS Rated output power Loudspeaker output Input sensitivity Input impedance Frequency response S/N ratio Controls Indicators Protection Power consmption Power supply dimensions Weight Twin channel 240W power amplifier 2x240W rms 100V line +/- 385mV balanced input 20 Kohm 80Hz 18Khz (+1dB, -3dB) >85dB Volume control on front panel Power, signal presence, overload, protection High temp, overload, short circuit 492W 220Vac 50Hz ; 24Vdc 484x380mm; 1U 5,6Kg Powder coated chassis, brushed and anodized aluminium front panel. EN 50102 IP protection class: IP31IK4 Pagina 15 di 16

WayGuard WG DPA124 TECHNICALSPECIFICATIONS Rated output power Loudspeaker output Input sensitivity Input impedance Frequency response S/N ratio Controls Indicators Protection Power consmption Power supply dimensions Weight Quad channel 240W power amplifier 4x120W rms 100V line +/- 385mV balanced input 20 Kohm 80Hz 18Khz (+1dB, -3dB) >85dB Volume control on front panel Power, signal presence, overload, protection High temp, overload, short circuit 576W 220Vac 50Hz ; 24Vdc 484x380mm; 1U 8,5Kg Powder coated chassis, brushed and anodized aluminium front panel. EN 50102 IP protection class: IP31IK4 Pagina 16 di 16