Pump Trailer Submersible PTS-60000

Pump Trailer Submersible PTS-60000 Technical specification Table of contents: 1. TECHNICAL DATA 2. GENERAL 3. ENGINE 4. FIRE PUMP 5. SUBMERSIBLE PUMPS 6. PIPING 7. OPERATING PANEL 8. LIGHTING AND ELECTRICAL EQUIPMENT 9. PAINT AND FINISH 10. MANUALS pagina 1 van 16 / page 1 of 16

1. TECHNICAL DATA 1.1 DIMENSIONS Overall length : 13.600 m. Overall width : 2.500 m. Overall height : 3.963 m. 1.2. WEIGHTS Weight: Total (appr.) : 22,000 kg Admissible weight: Total : 27,000 kg 1.3 PUMP CAPACITY Pump capacity (5 m suction height) : 60.000 lpm @ 11,0 bar Fire pump engine power : 1.417 kw. Submersibles capacity : 12.000 lpm @ 3,0 bar (5x) Hydro pack engine power : 847 kw. Max. height above water level : +/- 15 meter Max. distance from open water source : +/- 50 meter pagina 2 van 16 / page 2 of 16

2. GENERAL 2.1. GENERAL A modular design concept has been adopted in the pump trailer design. The GVW of the 2 axle trailer is 27,0 ton. The trailer is designed for use under heavy duty firefighting conditions. The firefighting system consists of a main fire pump with 5 submersible pumps. Capacity of the system is 60.000 lpm at 11,0 bar. Main fire pump is direct driven from Caterpillar diesel engine. Submersibles are hydraulic driven. Hydro pack is driven with separate Caterpillar diesel engine. Hydraulic crane it is provided for installation and position submersibles. Trailer is provided with closed superstructure with noise insulation and material lockers. Truck is not part of supply. 2.2. TRAILER CHASSIS Total admissible weight trailer : 27.000 kg. Frame : Galvanized and coated in RAL3000 Axles : 2x 9 ton air suspension Brake system type : 2-circuit air brake system WABCO ABS/EBS. Side protection : Included Wheel fenders : Including anti-spray mudguards Lighting : According international regulations pagina 3 van 16 / page 3 of 16

3. ENGINE Make : Caterpillar Type : C32 Marine Power : 1417 kw at 2300 rpm Cylinders : 12 Bore : 145 mm Stroke : 162 mm Displacement : 32,1 Liter Emission : EPA Tier 2/ IMO 2 Cooling system : Heat exchanger Fuel consumption : 342 l/h at 1320 kw Fuel tank : 2000 l Electrical system : 24 V Batteries : 2x 12 V 4. FIRE PUMP Type : HGTF1 350.650-vertical Capacity : 3636 m³/h (60.600 lpm) @ 9,0 bar (See attached pump diagram) Required power : 1248 kw at 1750 rpm Available power : 1325 kw at 1750 rpm pagina 4 van 16 / page 4 of 16

pagina 5 van 16 / page 5 of 16

5. SUBMERSIBLE PUMPS Submersible pumps (5x): Type of pump : Floating Type of drive : Hydraulic motor Capacity : 12.000 lpm @ 3,0 bar (5x) Total capacity : 60.000 lpm @ 3,0 bar Transportation : Trolleys are included Fire hose : 12 Length : 50 meter (not part of supply) Hydraulic power: Type : Diesel driven hydro pack Engine : Caterpillar Type: C18 Power: 847 kw Cooling system : Heat exchanger Hydraulic pump : Parker Hydraulic hose reels : 5x Length : 50 meter Rewind : Hydraulic powered Winch (2x) : Hydraulic powered Cable length : 60 meter Pulling strength : 1.500 kg Hydraulic crane : Fassi Type : F80A Capacity : 55 knm Max. outreach : 10,95 meter pagina 6 van 16 / page 6 of 16

6. PIPING AND VALVES All pipes and valves are of material fully compatible with AFFF concentrate, protein based foam compound (FFFP), salt water or water/foam solution. Pipe material will be stainless steel 316L. All pipes are of sufficient diameter to permit full flow of liquid with minimum loss of pressure. Wherever required, flexible connections and welded joints with bolted flexible couplings are provided to avoid the piping being exposed to external forces and to facilitate removal and replacement. The drain valves are located in such positions as to permit complete draining of water pump and piping. All couplings are complete with blank cap and chain. All couplings are made of corrosion resistant material. Inlet manifold: Number : 5 Dimensions : 10 Valves : Butterfly valve Couplings : MultiLug or other couplings upon request Pressure manifold: Number : 3 Dimensions : 12 Valves : Butterfly valves. Couplings : MultiLug or other couplings upon request Draining: Draining of the entire pump and piping is provided with several ball valves on the lowest positions. This ensures the complete draining. Flushing: After use flushing with clean water is possible with the existing suction an pressure connections and the drain valves. pagina 7 van 16 / page 7 of 16

7. OPERATING PANEL An operating panel is provided at the right side of the trailer, including: Start/stop switch Vacuum pressure indication suction side Pressure indication pressure side All engine indications, oil pressure, rpm, temperature, etc. Voltmeter gauche Water temperature gauche Tachometer / hour meter pump engine Engine rpm control Power pack control All functions and screens are programmable including failure analysis 8. LIGHTING AND ELECTRICAL EQUIPMENT The lighting is in accordance with international standards, including 2 rear brake lights and 2 reversing lights. Several work light are provided at the front and the rear and near the operating panel. 8 orange flashing lights, 2 at each side of the trailer, are provided All wiring is properly protected against water and mechanical damage. 9. PAINT AND FINISH The final painting of the superstructure of the trailer is in red, RAL 3000, or other color when required. Paint procedure is according to paint manufacturer's instructions. 9.1. RUSTPROOFING Chassis frame is galvanized Axles and supports are in black standard coating Wheels and side bars are in silver grey Rear bar is finished in white 9.2. SIGN WRITING. Sign writing, logo s or reflecting tape is not included but can be applied when required. 10. MANUALS 10.1. OPERATION MANUAL With the trailer a manual containing operation instructions in the English language is provided. This manual also includes danger warnings, technical specifications of the automotive components, trailer identification, trailer operation, periodic checks and maintenance. pagina 8 van 16 / page 8 of 16