PIPE OUTSIDE DIAMETER GUIDE

May 21, 2015-1 PIPE OUTSIDE DIAMETER GUIDE PIPE OUTSIDE DIAMETER GUIDE - SMALL DIAMETER PIPE SIZES NOMINAL PIPE SIZES 1 /2" 3 /4" 1" 1 1 /4" 1 1 /2" 2" 2 1 /2" THIS O.D. GUIDE IS FOR YOUR CONVENIENCE & IS BASED ON THE LATEST PIPE STANDARDS & INFORMATION SUPPLIED COPPER TUBING.63.88 1.13 1.38 1.63 2.13 2.63 BY MANUFACTURERS. DUE TO OCCASIONAL CHANGES & VARIANCES IN OUTSIDE DIAMETERS, THE PIPE O.D. SHOULD STEEL & PLASTIC PIPE.84 1.05 1.32 1.66 1.90 2.38 2.88 ALWAYS BE VERIFIED BEFORE ORDERING FITTINGS. PIPE OUTSIDE DIAMETER GUIDE - STANDARD PRESSURE PIPE SIZES NOMINAL PIPE SIZES 3" 4" 5" 6" 8" 10" 12" 14" 15" 16" 18" 20" 24" 30" COPPER TUBING 3.13 4.13 5.13 6.13 STEEL & PLASTIC (SDR 26.21 & SCHD) 3.50 4.50 5.56 6.63 8.63 10.75 12.75 14.00 16.00 18.00 20.00 24.00 30.00 PLASTIC IRRIGATION PIPE (PIP) 4.13 6.14 8.16 10.20 12.24 15.30 18.70 22.05 24.80 PLASTIC SEWER PIPE (SDR 35) 4.22 6.28 8.40 10.50 12.50 15.30 18.70 24.80 PLASTIC (PVC) AWWA C-900/C-909 4.80 6.90 9.05 11.10 13.20 15.30 17.40 19.50 21.60 25.80 POLYETHYLENE PIPE (IPS SIZE) 3.50 4.50 6.63 8.63 10.75 12.75 14.00 16.00 18.00 20.00 24.00 30.00 POLYETHYLENE PIPE (DIP SIZE) 4.80 6.90 9.05 11.10 13.20 15.30 17.40 19.50 21.60 25.80 32.00 DUCTILE IRON PIPE 3.96 4.80 6.90 9.05 11.10 13.20 15.30 17.40 19.50 21.60 25.80 32.00 CAST IRON PIPE CLASS 100-250 AWWA 3.96 4.80 6.90 9.05 11.10 13.20 15.30 17.40 19.50 21.60 25.80 32.00 CLASS A - AWWA PIT CAST 3.80 4.80 6.90 9.05 11.10 13.20 15.30 17.40 19.50 21.60 25.80 31.74 CLASS B - AWWA PIT CAST 3.96 5.00 7.10 9.05 11.10 13.20 15.30 17.40 19.50 21.60 25.80 32.00 CLASS C THRU D - AWWA PIT CAST 3.96 5.00 7.10 9.30 11.40 13.50 15.65 17.80 19.92 22.06 26.32 ABESTOS CEMENT PIPE - CLASS 100 MACHINED END 3.74 4.64 6.91 9.11 11.24* 13.44* 15.07 17.15 19.90 22.12 26.48 33.12 FLIN-TITE ROUGH BARREL 3.94 4.90 7.13 9.33 11.30 13.42 15.45 17.60 FLUID-TITE ROUGH BARREL 3.93 5.05 7.16 9.32 11.46 13.70 15.36 17.50 20.44 22.50 27.17 PERMAFLEX ROUGH BARREL 4.84 7.15 9.35 11.47 13.74 15.55 17.55 20.50 22.70 27.15 RING-TITE ROUGH BARREL 3.95 4.92 7.19 9.39 11.47 13.74 15.51 17.65 20.44 22.68 27.12 33.80 MINIMUM STANDARD ROUGH BARREL 4.79 7.05 9.22 11.25 13.37 15.36 17.50 MAXIMUM STANDARD ROUGH BARREL 5.26 7.40 9.57 11.77 14.04 15.80 17.94 ABESTOS CEMENT PIPE - CLASS 150 MACHINED END 3.84 4.81 6.91 9.11 11.66 13.92 16.22 18.46 20.94 23.28 27.96 35.00 FLIN-TITE ROUGH BARREL 4.40 5.06 7.13 9.33 11.88 14.14 16.48 18.72 FLUID-TITE ROUGH BARREL 4.03 5.14 7.12 9.32 11.85 14.11 16.41 18.65 21.20 23.54 28.22 PERMAFLEX ROUGH BARREL 5.00 7.20 9.40 11.92 14.20 16.50 18.75 21.30 23.64 28.32 RING-TITE ROUGH BARREL 4.13 5.07 7.17 9.37 11.92 14.18 16.48 18.72 21.30 23.64 28.32 35.42 MINIMUM STANDARD ROUGH BARREL 4.97 7.07 9.27 11.82 14.08 16.38 18.62 MAXIMUM STANDARD ROUGH BARREL 5.32 7.37 9.62 12.12 14.38 16.73 18.97 ABESTOS CEMENT PIPE - CLASS 200 MACHINED END 3.84 4.81 6.91 9.11 11.66 13.92 16.22 18.46 22.18 24.66 29.62 37.06 FLIN-TITE ROUGH BARREL 4.17 5.32 7.26 9.44 11.88 14.14 16.53 18.84 FLUID-TITE ROUGH BARREL 4.18 5.32 7.36 9.46 11.88 14.11 16.44 18.74 PERMAFLEX ROUGH BARREL 5.32 7.25 9.50 11.95 14.20 16.55 18.90 22.54 25.02 29.98 RING-TITE ROUGH BARREL 4.17 5.33 7.32 9.50 11.92 14.18 16.59 18.90 22.54 25.02 29.98 37.48 MINIMUM STANDARD ROUGH BARREL 5.22 7.26 9.39 11.77 14.03 16.44 18.74 MAXIMUM STANDARD ROUGH BARREL 5.57 7.60 9.79 12.12 14.38 16.88 19.19 *FLIN-TITE ME IS 10.89 FOR 10" & 12.99 FOR 12" SIZES

-2 May 21, 2015 WATER MAIN BELL-TITE DUCTILE IRON PRESSURE WATER MAIN CENTRIFUGALLY CAST IN METAL MOLDS AVAILABLE IN 3" TO 24" DIAMETER STOCKED IN 4" TO 12" DIAMETER SSC No. Pipe Class Nominal Size Ductile Iron Wgt Lbs/Ft Pipe Length Price Each 56A 0350 CLASS 51 4" 4.80 OD 15.44 20' $ 588.35 56A 0363 CLASS 50 6" 6.90 19.50 20' 473.82 56A 0366 CLASS 50 8" 9.05 27.20 20' 661.43 56A 0368 CLASS 50 10" 11.10 35.80 20' 783.97 56A 0369 CLASS 50 12" 13.20 45.30 20' 988.93 NOMINAL OLD STYLE PIPE SIZE CAST IRON 4" 5.00 OD 6" 7.10 8" 9.30 10" 11.40 12" 13.50 C-900 PVC WATER MAIN AWWA C 900 STANDARD FOR PVC PRESSURE PIPE FOR WATER CLASS 150 (DR-18) & CLASS 200 (DR-14) RING-TITE JOINTS STOCKED IN SIZES 4" TO 8" DIAMETER SSC No. Pipe Class Pipe Size O.D. Min. Wall Lbs/Ft Pipe Length Price Each 56A 0490 CLASS 150 4" 4.80.267 2.48 20' $ 77.02 56A 0500 CLASS 150 6" 6.90.383 5.13 20' 152.13 56A 0510 CLASS 150 8" 9.05.503 8.83 20' 263.75 56A CLASS 200 4" 4.80.343 3.12 20' Call For Price 56A 0550 CLASS 200 6" 6.90.493 6.47 20' 190.99 56A 0600 CLASS 200 8" 9.05.646 11.13 20' 328.24 MECHANICAL JOINT FITTINGS COMPACT DUCTILE IRON CEMENT LINED FITTINGS ONLY 1 /4 BEND MJ X MJ 56A 1010 5-600 2" $ 79.31 56A 1030 5-600 3" 81.71 56A 1040 5-600 4" 88.92 56A 1060 5-600 6" 145.40 56A 1070 5-600 8" 211.49 56A 1080 5-600 10" 336.46 56A 1090 5-600 12" 453.02 1 /4 BEND MJ X P.E. 56A 1410 5-603 4" $ 105.75 56A 1420 5-603 6" 175.44 1 /8 BEND MJ X MJ 56A 1140 5-605 4" $ 73.30 56A 1150 5-605 6" 117.76 56A 1160 5-605 8" 171.84 56A 1170 5-605 10" 251.15 56A 1180 5-605 12" 374.92 1 /16 BEND MJ X MJ 56A 1240 5-609 4" $ 69.70 56A 1250 5-609 6" 108.15 56A 1260 5-609 8" 168.23 1 /32 BEND MJ X MJ 56A 1340 5-611 4" $ 66.09 56A 1350 5-611 6" 111.75 56A 1360 5-611 8" 152.61 TEE MJ X MJ X MJ 56A 1560 5-620 2" $ 96.13 56A 1580 5-620 3" 109.35 56A 1590 5-620 4" 116.56 56A 1610 5-620 6" 210.29 56A 1620 5-620 8" 316.03 56A 1630 5-620 10" 451.82 56A 1640 5-620 12" 630.87 REDUCING TEE MJ X MJ X MJ 56A 1660 5-620 4" x 2" $ 175.44 56A 1710 5-620 6" x 4" 195.87 56A 1730 5-620 8" x 4" 227.11 56A 1750 5-620 8" x 6" 261.96 56A 1810 5-620 10" x 6" 337.66 56A 1820 5-620 12" x 4" 426.59 56A 1830 5-620 12" x 6" 426.59 56A 1850 5-620 12" x 8" 492.68

May 21, 2015 MECHANICAL JOINT FITTINGS COMPACT DUCTILE IRON CEMENT LINED FITTINGS ONLY TAPPED TEE MJ X MJ X F.I.P. 56A 1890 5-642 4" x 2" $ 150.21 CROSS MJ X MJ X MJ X MJ 56A 1980 5-631 4" $ 251.15 56A 1990 5-631 6" 307.62 56A 2050 5-631 6" x 4" 273.98 56A 2010 5-631 8" 335.26 56A 2060 5-631 8" x 4" 433.80 56A 2080 5-631 8" x 6" 318.44 REDUCER P.E. X P.E. -2A 56A 2760 5-638 6" x 4" $ 102.14 56A 2770 5-638 8" x 6" 161.02 SHORT SOLID SLEEVES MJ x MJ SSC No. Manuf No. Size Length Price Each 56A 3160 5-644S 2" 7 1 /2" $ 86.52 56A 3210 5-644S 3" 7 1 /2" 57.68 56A 3270 5-644S 4" 7 1 /2" 55.28 56A 3310 5-644S 6" 7 1 /2" 98.54 56A 3340 5-644S 8" 7 1 /2" 128.58 56A 3370 5-644S 10" 7 1 /2" 233.12 56A 3410 5-644S 12" 7 1 /2" 261.96 ADAPTER FLANGE X P.E. 56A 3040 5-661 4" x 16" $ 181.33 56A 3110 5-661 6" x 16" 226.66 REDUCER MJ X MJ 56A 2240 5-635 4" x 2" $ 105.75 56A 2270 5-635 4" x 3" 74.50 56A 2330 5-635 6" x 4" 62.53 56A 2370 5-635 8" x 6" 122.57 56A 2385 5-635 10" x 6" 158.62 56A 2390 5-635 10" x 8" 174.24 56A 2410 5-635 12" x 8" 215.10 56A 2420 5-635 12" x 10" 237.93 REDUCER SEB 56A 2440 5-636 4" x 2" $ 173.04 56A 2470 5-636 4" x 3" 69.70 56A 2540 5-636 6" x 4" 86.52 56A 2570 5-636 8" x 4" 146.60 56A 2580 5-636 8" x 6" 132.18 REDUCER LEB 56A 2610 5-637 4" x 2" $ 80.51 56A 2620 5-637 6" x 4" 132.18 56A 2650 5-637 8" x 6" 121.37 LONG SOLID SLEEVES MJ x MJMJ X MJ SSC No. Manuf No. Size Length Price Each 56A 3280 5-644L 4" 12" $ 78.11 56A 3320 5-644L 6" 12" 130.98 56A 3350 5-644L 8" 12" 215.10 56A 3380 5-644L 10" 12" 255.95 56A 3430 5-644L 12" 12" 346.08 SOLID CAP MJ X MJ 56A 4310 5-650 2" $ 61.28 56A 4340 5-650 4" 32.45 56A 4350 5-650 6" 57.68 56A 4360 5-650 8" 96.13 TAPPED CAP MJ x F.I.P. 56A 4470 5-652 6" x 2" $ 93.73 SOLID PLUG MJ X MJ 56A 4010 5-654 2" $ 57.68 56A 4050 5-654 4" 39.65 56A 4060 5-654 6" 76.91 56A 4070 5-654 8" 115.36 56A 4080 5-654 10" 203.08 56A 4090 5-654 12" 199.47 TAPPED PLUG MJ x F.I.P. 56A 4120 5-655 2" x 2" $ 86.52 56A 4170 5-655 4" x 2" 74.50 56A 4220 5-655 6" x 2" 111.75

-2B May 21, 2015 MECHANICAL JOINT FITTINGS COMPACT DUCTILE IRON CEMENT LINED FITTINGS ONLY CAST IRON FLANGED FITTINGS MISC PUSH-IN PLUG WITH EARS 56A 6410 5-176 4" $ 51.67 56A 6420 5-176 6" 84.12 BOLT SIZES FOR MECHANICAL JOINT FITTINGS SIZE OF FITTING 3" 4" 6" 8" 10" 12" BOLT SIZE 5 /8" x 3" 3 /4" x 3" 3 /4" x 3 1 /2" DUAL PURPOSE DUCTILE IRON SOLID SLEEVE MJ X MJ SSC No. Size OD Lbs Price Each 56A 3440 4" x 12" 4.80/5.00 45 $ 406.16 56A 3450 6" x 12" 6.90/7.10 65 511.90 56A 3460 8" x 12" 9.05/9.30 85 652.50 CAST IRON FLANGED SHORT RADIUS 90 ELL SSC No. Manuf No. Size R A Price Each 56A 6490 5-700 4" 4.5 6.5 $ 147.05 56A 6495 5-700 6" 6.0 8.0 254.75 CAST IRON FLANGED STRAIGHT TEE SSC No. Manuf No. Size R A Price Each 56A 6500 5-720 4" 6.5 6.5 $ 300.41 56A 6505 5-720 6" 6.0 8.0 374.92 MJ GLAND PACK ACCESSORY SET SSC No. Manuf No. Size Bolt Size Lbs Price Each WITH T-HEAD BOLTS & NUTS & MJ GASKET 56A 0840 2" 5/8" X 3" 5 $ 19.23 56A 0850 3" 5/8" X 3" 7 20.43 56A 0860 085164 4" 3/4" X 3 1 /2" 8 27.64 56A 0870 085171 6" 3/4" X 3 1 /2" 12 38.45 56A 0880 085188 8" 3/4" X 3 1 /2" 15 43.26 56A 0890 085195 10" 3/4" X 4" 20 61.28 56A 0900 085201 12" 3/4" X 4" 25 64.89 MJ TRANSITION GLAND PACK SSC No. Manuf No. Size Lbs Price Each SBR TRANSITION GASKET & T-HEAD BOLTS & NUTS 56A 0905 085423 4" 8 $ 28.84 56A 0910 085430 6" 11 39.65 56A 0915 085447 8" 15 44.46 MJ VALVE ACCESSORY SET SSC No. Manuf No. Size Lbs Price Each WITH ANTI-ROTATION BOLTS & NUTS & MJ GASKET 56A 8000 4" 8 $ 23.81 56A 8005 6" 12 30.87 56A 8010 8" 15 42.18 EBBA IRON RETAINER GLAND SSC No. Size Price Each 56A 7470 4" With Set Screws $ 26.44 56A 7480 6" With Set Screws 44.46 56A 7490 8" With Set Screws 52.87 56A 7510 12" With Set Screws 130.98 U.S. PIPE TYTON JOINT PLUG SSC No. Size Lbs Price Each 56A 6510 4" $ 34.61 HARCO TRANSITION GASKET FOR STEEL PIPE WITH M.J. CONNECTIONS 56A 7200 40202 2" $ 4.12 56A 7250 40203 3" 5.15 56A 7300 40204 4" 6.18 56A 7350 40206 6" 7.21 56A 7400 40208 8" 10.30 56A 7450 40210 10" 12.36 56A 7460 40212 12" 14.42

May 21, 2015-3 SERIES 1300 RESTRAINERS FOR PVC & DUCTILE IRON PIPE ADAPTERS & RESTRAINTS Price Change SSC No. Manuf No. Size Wgt Lbs Price Each 56I 6093 UFR1300-S-4 4" IPS 10 $ 57.67 56I 6094 UFR1300-C-4 4" CIP 10 57.00 56I 6095 UFR1300-S-6 6" IPS 11 70.67 56I 6096 UFR1300-C-6 6" CIP 11 70.00 56I 6097 UFR1300-S-8 8" IPS 17 95.41 56I 6098 UFR1300-C-8 8" CIP 17 116.66 CAM-LOCK JOINT RESTRAINT KIT FOR MJ FITTINGS ON DUCTILE IRON PIPE COLOR-CODED NUTS & WEDGES EPOXY COATING WIDER WEDGES & LONGER T-BOLTS BOXED WITH WITH DUCTILE IRON GASKET, BOLTS & NUTS SSC No. Manuf No. Size No Of Wedges Type of Pipe Working Pressure Wgt Lbs Price Each 56A 7700 111-048000-000 4" 2 Ductile Iron Pipe 350 PSI 11.8 $ 43.66 56A 7710 111-069000-000 6" 3 Ductile Iron Pipe 350 PSI 17.8 53.76 56A 7720 111-090500-000 8" 3 Ductile Iron Pipe 350 PSI 20.3 73.20 56A 7730 111-111000-000 10" 6 Ductile Iron Pipe 350 PSI 32.5 96.78 56A 7740 111-132000-000 12" 8 Ductile Iron Pipe 350 PSI 40.4 132.25 CAM-LOCK JOINT RESTRAINT KIT FOR MJ FITTINGS ON C-900 PVC PIPE COLOR-CODED NUTS & WEDGES EPOXY COATING WIDER WEDGES & LONGER T-BOLTS BOXED WITH WITH DUCTILE IRON GASKET, BOLTS & NUTS SSC No. Manuf No. Size No Of Wedges Type of Pipe Working Pressure Wgt Lbs Price Each 56A 7780 120-048000-000 4" 2 C-900 PVC Pipe Up To 250 PSI 12.2 $ 49.95 56A 7785 120-069000-000 6" 3 C-900 PVC Pipe Up To 250 PSI 18.3 62.37 56A 7790 120-090500-000 8" 3 C-900 PVC Pipe Up To 250 PSI 20.8 85.84 56A 7795 120-111000-000 10" 6 C-900 PVC Pipe Up To 250 PSI 33.4 137.31 56A 7798 120-132000-000 12" 8 C-900 PVC Pipe Up To 250 PSI 42.0 144.73 For More Information On These Products Or On Products Not Listed, Call Salina Supply Company At (785) 823-2221 ADAPTERS FOR CAST IRON 125 LB CAST IRON SERIES 200-C CLASS 125 150 LB STEEL SERIES 200-S CLASS 150 SSC No. Manuf No. Size PSI Temp Range Price Each 56A 7520 200-C 4" 250 PSI 20 to 150 F $ 66.75 56A 7530 200-C 6" 250 PSI 20 to 150 F 73.15 56A 7540 200-C 8" 250 PSI 20 to 150 F 101.69 56A 7550 200-C 10" 175 PSI 20 to 150 F 183.30 Nominal Pipe Size Pipe OD Steel 200-S Pipe OD Cast Iron 200-C Dimensions A B BC Bolt Hole Dia Set Screw ty Set Screw Size 2" 2.375 2.50 6" 1 13 /16" 4 3 /4" 3 /4" 2 1 /2" x 1" 3.5 2 1 /2" 2.875 7" 1 13 /16" 5 1 /2" 3 /4" 4 1 /2" x 1" 4 3" 3.500 3.96 7 1 /2" 1 13 /16" 6" 3 /4" 4 1 /2" x 1" 5 4" 4.500 4.80 9" 1 7 /8" 7 1 /2" 3 /4" 4 1 /2" x 1" 7.7 5" 5.563 10" 1 7 /8" 8 1 /2" 7 /8" 8 1 /2" x 1" 8.7 6" 6.625 6.90 11" 1 7 /8" 9 1 /2" 7 /8" 8 1 /2" x 1" 10 8" 8.625 9.05 13 1 /2" 2 1 /4" 11 1 /2" 7 /8" 8 5 /8" x 1 1 /4" 16.5 10" 10.750 11.10 16" 2 1 /4" 14 1 /4" 1" 12 5 /8" x 1 1 /4" 22 12" 12.750 13.20 19" 2 1 /4" 17" 1" 12 5 /8" x 1 1 /4" 31 Wgt Lbs Aprx

-4 May 21, 2015 B-101 TAPPING MACHINE & ACCESSORIES FOR TAPPING WATER MAINS & INSERTING CORPORATION STOPS 1 /2" TO 1" INCLUSIVE UNDER PRESSURE. HAND OR POWER OPERATION. SSC No. Manuf No. Max W.P. Without Power Clevis Max W.P. With Power Clevis Wgt Call For Price B-101 90 PSI 250 PSI 113 Lbs ACCESSORIES FOR B-101 TAPPING MACHINE SSC No. Manuf No. Product Size Price Each 56F 8130 40021 Leather Washer $ 10.95 56F 8150 40036 Rubber Gate Washer 15.77 56F 8170 40066 Small Saddle Gasket $ 13.12 56F 8180 40067 Large Saddle Gasket 51.64 56F 8181 48234 Heavy Fiber Gasket 3 /4" $ 1.00 56F 8182 48235 Heavy Fiber Gasket 1" 1.20 56F 8190 58101 Packing $ 16.46 56F 8244 75812 Saddle 4" $ 70.31 56F 8246 75815 Saddle 6" 70.31 56F 8248 75817 Saddle 8" 70.31 56F 8250 75821 Saddle 12" 70.31 56F 8340 680539 Drill & Tap 3 /4" $ 284.95 56F 8350 680540 Drill & Tap 1" 378.57 56F 8370 680600 Screw Plug 3 /4" $ 238.22 56F 8390 680601 Screw Plug 1" 286.46 56F 8400 680648 Screw Plug 394.43 EUIPMENT FURNISHED WITH EACH MACHINE: RATCHET HANDLE SML & LRG SADDLE GASKET ROUND LINK CHAIN CHAIN HOOKS & NUTS CHAIN WASHERS CHAIN HOOK NUT WRENCH WRENCH E-Z PLUGS TOOL RETAINING SCREW BODY CLEANING DITCH CLOTH COMBINED DRILL & TAPS - MUELLER (CC) THREADS PIPE TO BE TAPPED TYPE Cast Iron Asbestos Mueller Thread With Regular Tap & Drill Length E-Z Release Screw Plug With Inside Thread. Cement Lined Ductile Iron Cement Lined Cast Iron SIZE 3" to 24" 3" to 16" 3" to 14" CLASS 100 150 200 DRILL LENGTH Regular Regular Regular CORPORATION STOP INLET OR PLUG THREAD 3 /4" 680539 680539 1" 680540 680540 B-101 B SELECT PROPER COMBINED DRILL & TAP ACCORDING TO: 1. SIZE & TYPE OF INLET THREAD OF CORPORATION STOP TO BE INSERTED. 2. MATERIAL FROM WHICH THE PIPE TO BE TAPPED IS MADE. 3. SIZE & CLASS OF PIPE TO BE TAPPED For More Information On These Products Or On Products Not Listed, Call Salina Supply Company At (785) 823-2221 PL-2 DRILLING MACHINE & ACCESSORIES FOR DRILLING PLASTIC OR FIBERGLASS COMPOSITE PIPE THROUGH COMBINED CLAMP & CORPORATION STOP OR BRASS CLAMP & CORPORATION STOP. SSC No. Manuf No. Product Price Each 56F 8620 PL-2 Drilling Machine Shown With Optional Ratchet Handle & Socket $ 273.98 MODEL NO. 2 DRILLS 11 /16" OR 7 /8" DIAMETER HOLES ACCESSORIES FOR PL-2 DRILLING MACHINE SSC No. Manuf No. Product Size Price Each 56F 8650 504108 Gasket 3/4" $ 1.17 56F 8840 88366 Cutting Grease $ 25.66 56F 8930 681919 3 /4" Shell Cutter 0.550" $ 169.46 56F 8933 681920 1" Shell Cutters 0.550" 169.46 ADAPTER NIPPLES FOR PL-2 DRILLING MACHINE SSC No. Manuf No. Corp Stop Out. Conn. Plas.Pipe Wall Gasket Price Each 56F 8780 507632 For Flare Thread 3 /4" 0.550" H-10893 $ 83.19 56F 8810 507633 For Flare Thread 1" 0.550" H-10895 83.19 UICKLY & EASILY WITH POSITIVE CONTROLLED FEED. TWO SHELL CUTTER LENGTHS ARE AVAILABLE TO ENABLE YOU TO CUT THROUGH PIPE HAVING A MAXIMUM WALL THICKNESS OF EITHER.0550" OR 1.125". THE REPLACEABLE SHELL CUTTER RETAINS THE COUPON & RARELY LEAVES CHIPS IN THE MAIN.

May 21, 2015-5 HYDRANTS & ACCESSORIES CENTURION FIRE HYDRANTS - 2 WAY OR 3 WAY 200 PSI WORKING & 400 PSI TEST PRESSURE. COMPRESSION TYPE MAIN VALVE CLOSES WITH THE PRESSURE. FULLY COMPLIES WITH AMERICAN WATER ASSOCIATION STANDARD C-502. SSC No. Manuf No. Size Wgt. Lbs. Price Each 2 WAY CENTURION FIRE HYDRANT 4" OR 6" D-150 INLET FITS DIP OR SAND CAST PIPE WITH PROPER GASKET 4" OR 6" D-150 INLET TWO 2 1 /2" NOMINAL HOSE NOZZLES 1 1 /2" PENTAGON OPERATING NUT 56C 0603 A-420 4" MJ 48" Bury 4 1 /2" Nom Main Valve Opening 457 $ 3,680.88 56C 0615 A-420 6" MJ 48" Bury 4 1 /2" Nom Main Valve Opening 457 3,691.62 3 WAY CENTURION FIRE HYDRANT 6" D-150 INLET FITS DIP OR SAND CAST PIPE WITH PROPER GASKET 6" D-150 INLET ONE 4 1 /2" NOM. PUMPER NOZZLE TWO 2 1 /2" NOM. HOSE NOZZLES 1 1 /2" PENTAGON OPERATING NUT 56C 0670 A-423 6" MJ 48" Bury 5 1 /2" Nom Main Valve Opening 524 $ 4,287.57 56C 0800 A-423 Yellow 6" Flg 5' Bury 5 1 /2" Nom Main Valve Opening 531 4,411.84 *Price Change MAINGUARD POST FLUSH HYDRANT LOCKING COVER IRON NOZZLE CAP TRAFFIC BREAKAWAY NO SPECIAL OPERATING WRENCH REUIRED SSC No. Manuf No. Size Wgt. Lbs. Price Each 56C 1490 77 48" Bury 2" Fip Side Inlet 57 $ 921.34 * ALL WEATHER HYDRANT LUBRICATING OIL SSC No. Manuf No. Size Flow Range Price Each 56C 1760 280354 10.5 Oz. -60 TO 150 F $ 26.09 56C 1763 184048 1 Gal. -60 TO 150 F 66.25 POLLARD ADJUSTABLE WRENCH & SPANNER SSC No. Manuf No. Lbs. Price Each 56K 3600 P-66602 4.5 $ 38.27 SAFETY FLANGE REPAIR KIT SSC No. Manuf No. Hyrant Size Wgt. Lbs. Price Each STEEL SAFETY STEM COUPLING, SS CLEVIS & COTTER PINS, SAFETY FLANGE & GASKET, 3 BOLTS WITH NUTS & 1 CAN OF HYDRANT LUBRICATING OIL. 56C 1660 A-300 4 1 /4" & 4 1 /2" 12 $ 325.09 56C 1680 A-301 5 1 /4" 14 318.17 HYDRANT BONNET REPAIR KIT 56C 2681 A-280360 4 1 /2" $ 87.65 HYDRANT EXTENSION SECTIONS SSC No. Manuf No. Hyrant Size Extension Wgt. Lbs. Price Each EXTENSION BARREL, STEEL STEM COUPLING, 8 BOLTS WITH NUTS, SS CLEVIS & COTTER PINS, SOLID FLANGE & GASKET & CAN OF HYDRANT LUBRICATING OIL. 56C 2230 A-319 4 1 /4" & 4 1 /2" 6" 50 $ 629.22 56C 2260 A-319 4 1 /4" & 4 1 /2" 12" 87 738.34 56C 2310 A-319 4 1 /4" & 4 1 /2" 18" 99 784.82 56C 2314 A-319 4 1 /4" & 4 1 /2" 24" 111 870.28 56C 2505 A-320 5 1 /4" 6" 66 $ 701.84 56C 2510 A-320 5 1 /4" 12" 87 819.48 56C 2560 A-320 5 1 /4" 18" 105 930.37 56C 2610 A-320 5 1 /4" 24" 128 1,010.73 PUMPER NOZZLE CAP GASKET 56C 1800 A-15 4 1 /2" $ 16.60 BRASS SLEEVE PROTECTS O RINGS FROM DAMAGE BY STEM THREADS WHEN REMOVING HOUSING FROM THE UPPER STEM. SSC No. Manuf No. Price Each 56C 1830 A-367 $ 54.72 OPERATING WRENCH SSC No. Manuf No. Lbs. Price Each 56C 1820 A-311/A-2409 12.0 $ 43.70 For More Information On These Products Or On Products Not Listed, Call Salina Supply Co. At (785) 823-2221 BRASS COUPLING SUB ASSEMBLY 56C 1685 H95-H75-H94 $ 209.32 NS HOSE NOZZLE GASKET 56C 1810 A-19 2 1 /2" $ 5.49 DRAIN VALVE FACING 56C 2629 142811 $ 5.05 OLD STYLE STEM ASSEMBLY 56C 2645 184466 6" $ 230.04 56C 2648 184467 12" 240.22 56C 2650 184468 18" 250.70 56C 2655 184469 24" 261.17 MAIN VALVE & GASKET 56C 2663 190435 4 1 /4" $ 133.81 MAIN VALVE 56C 2668 195800 4 1 /2" $ 164.76 56C 2670 192913 5 1 /4" 199.64 SHOE REPAIR KIT 56C 2685 280363 4.5 VO IMPR $ 231.64

-6 May 21, 2015 GATE VALVE TAPPING VALVE & SLEEVE FLANGED X MECHANICAL JOINT GATE VALVE MJ WITH ACCESSORIES X 150 LB FLANGE LESS ACCESSORIES. IRON BODY & BRONZE TRIM. NON RISING STEM. FURNISHED WITH 2" OPERATING NUT. RESILIENT SEAT. STOCKED IN: 4", 6" & 8" 56C 2895 A-2360-16 4" $ 1,036.80 56C 2900 A-2360-16 6" 1,360.49 56C 2903 A-2360-16 8" 2,119.15 MECHANICAL JOINT TAPPING VALVE MJ WITH ACCESSORIES X FLANGE WITH CENTERING RING & ACCESSORIES. IRON BODY & BRONZE TRIM. NON RISING STEM. FURNISHED WITH 2" HANDWHEEL. RESILIENT SEAT. 56C 7110 T-2360-16-D 4" $ 1,344.33 56C 7160 T-2360-16-D 6" 1,863.46 56C 7210 T-2360-16-D 8" 2,763.51 56C 7260 T-2360-16-D 10" 4,137.53 56C 7270 T-2360-16-D 12" 6,323.57 MECHANICAL JOINT TAPPING SLEEVE D-150 MJ TAPPING SLEEVE WITH DUCK-TIPPED GASKETS FOR DUCTILE IRON PIPE. 200 PSI WORKING PRESSURE. STOCKED IN THE SIZES SHOWN BELOW. 56C 5410 H-615 4" x 4" $ 1,451.43 56C 5460 H-615 4" x 2" 342.72 56C 5465 H-615 4" x 3" 342.72 56C 5560 H-615 6" x 6" 1,725.56 56C 5710 H-615 6" x 4" 1,725.56 56C 5760 H-615 8" x 8" 2,294.22 56C 5810 H-615 8" x 4" 2,119.42 56C 5860 H-615 8" x 6" 2,119.42 56C 5960 H-615 10" x 4" 4,191.84 56C 6010 H-615 10" x 6" 4,191.84 56C 6050 H-615 10" x 8" 4,454.12 56C 5910 H-615 10" x 10" 4,541.35 56C 6110 H-615 12" x 4" 4,191.84 56C 6160 H-615 12" x 6" 4,191.84 56C 6210 H-615 12" x 8" 4,452.89 56C 6220 H-615 12" x 12" 5,297.09

May 21, 2015 CUT-IN VALVE & SLEEVE BUTTERFLY VALVE -6A MECHANICAL JOINT CUT-IN VALVE D-150 MECHANICAL JOINT ENDS WITH ACCESSORIES. IRON BODY & BRONZE TRIM. NON RISING STEM. 2" OPERATING NUT. RESILIENT SEAT. STOCKED IN: 4", 6" & 8" 56C 7815 C-2360-45 4" $ 1,484.59 56C 7820 C-2360-45 6" 2,018.91 56C 7825 C-2360-45 8" 3,131.10 MECHANICAL JOINT CUT-IN SLEEVE D-150 MECHANICAL JOINT SLEEVE. PLAIN RUBBER GASKET FOR OLD STYLE CAST IRON PIPE. GASKETS IN STOCK FOR USE ON DUCTILE IRON PIPE. STOCKED IN: 4", 6", 8", 10" & 12" 56C 7460 H-841 4" $ 597.28 56C 7510 H-841 6" 757.88 56C 7560 H-841 8" 1,043.92 56C 7563 H-841 10" 1,450.42 56C 7565 H-841 12" 1,722.71 FLANGED X MECHANICAL JOINT BUTTERFLY VALVE MECHANICAL JOINT WITH ACCESSORIES X FLANGE WITH CENTERING RING & ACCESSORIES. IRON BODY & BRONZE TRIM. NON RISING STEM. FURNISHED WITH 2" OPERATING NUT. RESILIENT SEAT. Manuf No. B-3211-20 Price Each Price On Application FIBER GASKET 56F 0165 H-10024 3 /4" Fiber Gasket $.13 COPPER & ASBESTOS GASKET 56F 0210 H-10029 1" Copper & Asbestos Gasket.40 DUCK TIPPED GASKETS 56F 7840 194732 4" Duck Tipped Gasket 44.05 56F 7842 194733 6" Duck Tipped Gasket 57.21 PLAIN RUBBER GASKETS 56F 7870 194738 4" Plain Rubber Gasket 25.40 56F 7872 194739 6" Plain Rubber Gasket 35.70 PLUGS 56F 0260 H-10033 3 /4" CC Plug 19.36 56F 0280 H-10033 1" CC Plug 20.44 BRASS BUSHING 56F 0290 H-10036 1" x 3 /4" CC Brass Bushing 54.12

-7 May 21, 2015 GATE VALVES FLANGED GATE VALVE IRON BODY & BRONZE TRIM. NON-RISING STEM. FURNISHED WITH HANDWHEEL. FLANGED ENDS. RESILIENT SEAT. STOCKED IN: 4", 6", 8", 10" & 12" 56C 3060 A-2360-6 2" $ 637.36 56C 3110 A-2360-6 3" 903.16 56C 2880 A-2360-6 4" 1,009.25 56C 2890 A-2360-6 6" 1,349.16 56C 2891 A-2360-6 8" 2,108.31 56C 2892 A-2360-6 10" 3,350.33 56C 3360 A-2360-6 12" 4,045.02 MECHANICAL JOINT GATE VALVE IRON BODY & BRONZE TRIM. NON-RISING STEM. 2" OPERATING NUT. MJ ENDS & ACCESSORIES. STOCKED IN: 4", 6", 8", 10" & 12" 56C 3760 A-2360-20 2" $ 727.15 56C 2905 A-2360-20 4" 1,089.02 56C 2910 A-2360-20 6" 1,409.70 56C 2920 A-2360-20 8" 2,193.10 56C 2930 A-2360-20 10" 3,408.19 56C 2940 A-2360-20 12" 4,307.76 VALVE SIZE CENTERLINE TO STEM TOP OUTSIDE DIAMETER FLANGED (FACE TO FACE) DIAMETER OF HAND- WHEEL TAPPING BOSSES (CNTR TO CNTR) TAPPING BOSS DIAMETER BOLT CIRCLE DIAMETER MAXIMUM TAP SIZE INSIDE DIAMETER DEPTH OF SOCKET MECHANICAL JOINT (END TO END) A B C D E F G H K L M 4" 16.31 9.0 9.0 11.0 5.25 1.5 7.5 0.75 4.9 2.5 10.0 6" 20.12 11.0 10.5 13.0 6.19 2.25 9.5 1.25 7.0 2.5 11.5 8" 23.75 13.5 11.5 14.0 7.50 2.25 11.75 1.5 9.15 2.5 11.5 10" 27.75 16.0 13.0 16.0 8.25 2.25 14.25 1.5 11.2 2.5 13.0 12" 31.50 19.0 14.0 16.0 8.50 3.0 17.0 2.0 13.2 2.5 14.0 THREADED GATE VALVE IRON BODY & BRONZE TRIM. NON-RISING STEM. WITH HANDWHEEL. NATIONAL PIPE THREADED ENDS. 56C 3410 A-2360-8 2" $ 621.77 56C 3460 A-2360-8 3" 916.61 56C 3510 A-2360-8 4" 316.25 SLIP JOINT GATE VALVE IRON BODY & BRONZE TRIM. NON-RISING STEM. 2" OPERATING NUT. PVC RADIAL COMPRESSION ENDS. PVC GASKET. 56C 4260 A-2360-37 2" $ 662.28 56C 4300 A-2360-37 3" 968.17 56C 4410 A-2360-37 4" 1,107.69

May 21, 2015-8 CHECK VALVES VALVE BOXES & ACCESSORIES GRAVITY OPERATED FLANGED SWING CHECK VALVE IRON BODY BRONZE DISC & SEAT STOCKED IN SIZES 4", 6" & 8" SSC No. Manuf No. Size E G H J K L Price Each 56C 4560 A-2602-6 4" 7 1 /4" 12 7 /8" 15 /16" 9" 7" 2 11 /16"" $ 1,232.06 56C 4610 A-2602-6 6" 9" 16 1 /2" 1" 11" 9 3 /8" 3 1 /4" 1,690.79 56C 4660 A-2602-6 8" 10 1 /2" 19 1 /2" 1 1 /8" 1 1 /2" 11 1 /2" 3 1 /4" 3,103.92 SPRING & LEVER FLANGED SWING CHECK VALVE SPRING & LEVER: RON BODY BRONZE DISC & SEAT STOCKED IN SIZES 4" & 6" SSC No. Manuf No. Size E G H J K L Price Each 56C 4510 A-2602-6-02 4" 7 1 /4" 12 7 /8" 15 /16" 9" 7" 2 11 /16" $ 1,283.76 56C 4530 A-2602-6-02 6" 9" 16 1 /2" 1" 11" 9 3 /8" 3 1 /4" 1,761.19 VALVE BOX RISERS 56D 3000 367-5032 2" $ 22.67 56D 3010 367-5034 3" 32.00 56D 3020 367-5036 4" 40.00 VALVE OPERATING WRENCH TEE HANDLE & SOCKET TO FIT 2" SUARE WRENCH NUT. SSC No. Manuf No. Length Price Each 56C 1900 A-24610 5' $ 114.66 56C 1920 A-24610 6' 200.00 SERIES 6850 2 PIECE SCREW TYPE VALVE BOX WITH LID MARKED WATER 5 1 /4" SHAFT FOR 4" TO 12" VALVES TOP BOTTOM SSC No. Manuf No. Size Lgth Wgt Lgth Wgt Price Each 56D 1010 461-S/6850 19" to 22" 10" 35 Lbs 15" 25 Lbs $ 49.00 56D 1060 562-S/6850 27" to 37" 16" 45 Lbs 24" 35 Lbs 115.20 56D 1160 564-S/6850 39" to 50" 16" 45 Lbs 36" 45 Lbs 166.40 56D 1210 664-S/6850 39" to 60" 26" 65 Lbs 36" 45 Lbs 176.00 WATER VALVE BOX TOP LESS LID 56D 1215 16-T 16" For 562-S & 564-S 32 Lbs $ 40.80 56D 1220 26-T 26" For 664-S 52 Lbs 52.13 VALVE BOX BOTTOM LESS LID 56D 1225 36-B 36" For 564-S 45 Lbs $ 53.00 EXTENSIONS FOR SERIES 6850 VALVE BOX 56D 1230 58 14" Height Increase 25 Lbs $ 40.00 56D 1235 59 18" Height Increase 30 Lbs 50.00 VALVE BOX RING & COVER 56D 1213 C6-45/V0675 Fits Over 6" PVC Pipe 24 Lbs $ 50.40 2" 3" 4" 6" 8" 10" 12" 461-S 23 to 29" 28 to 34" 31 to 37" 35 to 41" 39 to 45" 44 to 50" 48 to 54" 562-S 29 to 41" 34 to 46" 37 to 49" 41 to 53" 45 to 57" 50 to 62" 54 to 66" 564-S 41 to 53" 46 to 58" 49 to 61" 53 to 65" 57 to 69" 62 to 74" 66 to 78" 664-S 41 to 65" 46 to 70" 49 to 73" 53 to 77" 57 to 81" 62 to 86" 66 to 90" 666-S 53 to 77" 58 to 82" 61 to 85" 65 to 89" 69 to 93" 74 to 98" 78 to 102" 668-S 65 to 89" 70 to 94" 73 to 97" 77 to 101" 81 to 105" 86 to 110" 90 to 114" MINIMUM & MAXIMUM TRENCH DEPTHS FOR VALVE BOXES SERIES 6870 ROADWAY BOX WITH LID MARKED WATER 4 1 /4" SHAFT FOR 2", 2 1 /2" & 3" VALVES ARCH BASE & ROUND HEAD TOP BOTTOM SSC No. Manuf No. Size Lgth Wgt Lgth Wgt Price Each 56D 1760 142-R/6870 30" to 42" 18" 40 Lbs 27" 30 Lbs $ 178.30 56D 1810 143-R/6870 36" to 48" 18" 40 Lbs 34" 34 Lbs 193.74 56D 1830 144-RR 39" to 60" 26" 45 Lbs 36" 35 Lbs 222.01 56D 1850 49 Extension For 143-R Box $ 59.22 WATER

-9 May 21, 2015 GROUND KEY CORPORATION STOPS GROUND KEY CORPORATION STOP MALE IP THREAD INLET & OUTLET 56F 0150 H-10012-N 3 /4" Male IP Thread Inlet & Outlet $ 48.45 56F 0152 H-10012-N 1" Male IP Thread Inlet & Outlet 73.15 56F 0100 H-9969-N 2" Male IP Thread Inlet & Outlet 345.70 H-10012 GROUND KEY CORPORATION STOP I.P. THREAD INLET & F.I.P THREAD OUTLET 56F 0300 H-10046-N 2" I.P. Thread Inlet & F.I.P Thread Outlet $ 334.30 H-10046 GROUND KEY CORPORATION STOP MUELLER CC THREAD INLET & FLARE OUTLET 56F 4930 H-15000-N 5 /8" x 3 /4" Mueller CC Thread Inlet & Flare Outlet $ 52.41 56F 4950 H-15000-N 3 /4" Mueller CC Thread Inlet & Flare Outlet 46.43 56F 4970 H-199017-N 3 /4" Less Nut Mueller CC Thread Inlet & Flare Outlet 41.34 56F 4990 H-15000-N 1" Mueller CC Thread Inlet & Flare Outlet 70.87 56F 5020 H-199017-N 1" Less Nut Mueller CC Thread Inlet & Flare Outlet 61.51 56F 5040 H-15000-N 1 1 /2" Mueller CC Thread Inlet & Flare Outlet 203.37 56F 5060 H-15000-N 2" Mueller CC Thread Inlet & Flare Outlet 373.18 H-15000 GROUND KEY CORPORATION STOP MUELLER CC THREAD INLET & COMPRESSION OUTLET 56F 5110 H-15008-N 3 /4" CTS Mueller CC Thread Inlet & Compression Outlet $ 49.79 56F 5130 H-15008-N 1" CTS Mueller CC Thread Inlet & Compression Outlet 75.40 H-15008 56F 5140 H-15009-N 3 /4" IPS Mueller CC Thread Inlet & Compression Outlet 64.79 56F 5150 H-15009-N 1" IPS Mueller CC Thread Inlet & Compression Outlet 101.68 GROUND KEY CORPORATION STOP MALE IP THREAD INLET & FLARE OUTLET 56F 5210 H-15025-N 3 /4" Male IP Thread Inlet & Flare Outlet $ 46.43 56F 5230 H-15025-N 1" Male IP Thread Inlet & Flare Outlet 70.87 56F 5240 H-15025-N 1 1 /4" Male IP Thread Inlet & Flare Outlet 213.34 H-15025 GROUND KEY CORPORATION STOP MALE IP THREAD INLET & COMPRESSION OUTLET 56F 5245 H-15028-N 3 /4" Male IP Thread Inlet & Compression Outlet $ 49.79 56F 5250 H-15028-N 1" Male IP Thread Inlet & Compression Outlet 75.40 H-15028 GROUND KEY CORPORATION STOP I.P. THREAD INLET & COMPRESSION OUTLET 56F 5255 H-15029-N 3 /4" IPS I.P. Thread Inlet & Compression Outlet $ 57.40 56F 5260 H-15029-N 1" IPS I.P. Thread Inlet & Compression Outlet 101.67 H-15029

August 7, 2014 300 TM BALL CORPORATION STOPS ORI-CORP CORPORATION STOPS -9A 300 TM BALL CORPORATION STOP MUELLER CC THREAD INLET & FLARE OUTLET 56F 0070 B-25000-N 1 1 /2" Mueller CC Thread Inlet & Flare Outlet $ 213.72 56F 0080 B-25000-N 2" Mueller CC Thread Inlet & Flare Outlet 373.30 B-25000 300 TM BALL CORPORATION STOP MUELLER CC THREAD INLET & COMPRESSION OUTLET 56F 0090 B-25008-N 1 1 /2" Mueller CC Thread Inlet & Compression Outlet $ 213.72 56F 0095 B-25008-N 2" Mueller CC Thread Inlet & Compression Outlet 353.43 300 TM BALL CORPORATION STOP I.P. THREAD INLET & PACK JOINT FOR IPS PVC OUTLET 56F 9760 V-25058-N 2" I.P. Thread Inlet & Pack Joint For IPS PVC $ 358.03 B-25008 V-25058 ORI-CORP CORPORATION STOP MUELLER CC THREAD INLET & COMPRESSION OUTLET 56F 5160 H-15013-N 1 1 /2" CTS Mueller CC Thread Inlet & Compression Outlet $ 220.83 56F 5170 H-15013-N 2" CTS Mueller CC Thread Inlet & Compression Outlet 365.31 H-15013 CORPORATION STOP COUPLINGS EIGHTH BEND CORPORATION STOP COUPLING WITH COPPER GASKET SWIVEL NUT WITH INSIDE THREAD INLET & FLARE OUTLET 56F 5350 H-15064-N 3 /4" Swivel Nut With Inside Thread Inlet & Flare Outlet $ 45.12 56F 5370 H-15064-N 1" Swivel Nut With Inside Thread Inlet & Flare Outlet 64.17 H-15064 EIGHTH BEND CORPORATION STOP COUPLING WITH COPPER GASKET SWIVEL NUT WITH INSIDE COPPER THREAD INLET & MUELLER 110 CONDUCTIVE COMPRESSION OUTLET FOR CTS OD TUBING 56F 5550 H-15075-N 3 /4" Swivel Nut With Inside Copper Thrd Inlet & Cond. Compr. Outlet $ 66.60 56F 5560 H-15075-N 1" Swivel Nut With Inside Copper Thrd Inlet & Cond. Compr. Outlet 77.65 H-15075 UARTER BEND CORPORATION STOP COUPLING WITH COPPER GASKET SWIVEL NUT WITH INSIDE THREAD INLET & FLARE OUTLET 56F 5390 H-15069-N 3 /4" Swivel Nut With Inside Thread Inlet & Flare Outlet $ 45.49 56F 5440 H-15069-N 1" Swivel Nut With Inside Thread Inlet & Flare Outlet 56.79 H-15069 UARTER BEND CORPORATION STOP COUPLING WITH COPPER GASKET SWIVEL NUT WITH INSIDE COPPER THREAD INLET & MUELLER 110 CONDUCTIVE COMPRESSION OUTLET FOR CTS OD TUBING 56F 5570 H-15076-N 3 /4" Swivel Nut With Inside Copper Thrd Inlet & Cond. Compr. Outlet $ 53.63 56F 5580 H-15076-N 1" Swivel Nut With Inside Copper Thrd Inlet & Cond. Compr. Outlet 69.68 H-15076

-9B August 7, 2014 CORPORATION STOP COUPLINGS GASKETS STRAIGHT CORPORATION STOP COUPLING WITH COPPER GASKET INSIDE FLARE THREAD INLET & MUELLER 110 CONDUCTIVE COMPRESSION OUTLET FOR CTS PLASTIC PIPE 56F 5490 H-15071-N 3 /4" CTS Inside Flare Thrd Inlet & Mueller 110 Cond. Compr. Outlet $ 25.96 56F 5530 H-15071-N 1" CTS Inside Flare Thrd Inlet & Mueller 110 Cond. Compr. Outlet 38.13 H-15071 STRAIGHT CORPORATION STOP COUPLING WITH COPPER GASKET INSIDE FLARE THREAD INLET & MUELLER 110 CONDUCTIVE COMPRESSION OUTLET FOR IPS PLASTIC PIPE 56F 5532 H-15072-N 3 /4" IPS Inside Flare Thrd Inlet & Mueller 110 Cond. Compr. Outlet $ 42.11 56F 5534 H-15072-N 1" IPS Inside Flare Thrd Inlet & Mueller 110 Cond. Compr. Outlet 50.85 H-15072 STRAIGHT CORPORATION STOP COUPLING WITH COPPER GASKET INSIDE FLARE THREAD INLET & INSTA-TITE OUTLET FOR POLY PIPE 56F 5536 H-15073-N 3 /4" Inside Flare Thread Inlet & Insta-Tite Outlet For Poly Pipe $ 32.05 56F 5538 H-15073-N 1" Inside Flare Thread Inlet & Insta-Tite Outlet For Poly Pipe 51.80 H-15073 STRAIGHT CORPORATION STOP COUPLING WITH COPPER GASKET INSIDE FLARE THREAD INLET & FEMALE IPT OUTLET 56F 5540 H-15082-N 3 /4" Inside Flare Thread Inlet & Female IPT Outlet $ 27.25 56F 5541 H-15082-N 1" Inside Flare Thread Inlet & Female IPT Outlet 49.61 H-15082 STRAIGHT CORPORATION STOP COUPLING WITH COPPER GASKET INSIDE FLARE THREAD INLET & IPS INSERT OUTLET 56F 3820 H-12203-N 3 /4" Inside Flare Thread Inlet & IPS Insert Outlet $ 61.36 H-12203 COPPER CORPORATION STOP GASKETS 56F 5270 H-15053-N 3 /4" Copper Corporation Stop Gasket $ 1.37 56F 5290 H-15053-N 1" Copper Corporation Stop Gasket 1.91 H-15053 For More Information On These Products Or On Products Not Listed, Call Salina Supply Company At (785) 823-2221

August 7, 2014-10 CURB VALVES & STOPS MARK II ORISEAL STOP FEMALE IP THREAD INLET & OUTLET 56F 1110 H-10283-N 3 /4" $ 79.11 56F 1130 H-10283-N 1" 135.32 56F 1150 H-10283-N 1 1 /4" 201.88 56F 1160 H-10283-N 1 1 /2" 253.74 56F 1190 H-10283-N 2" 412.30 56F 1195 H-10284-N 3 /4" With Stop & Waste $ 84.07 56F 1197 H-10284-N 1" With Stop & Waste 140.17 56F 1199 H-10284-N 1 1 /4" With Stop & Waste 207.22 56F 1201 H-10284-N 1 1 /2" With Stop & Waste 259.19 56F 1203 H-10284-N 2" With Stop & Waste 417.66 ORISEAL STOP FEMALE IP THREAD INLET & OUTLET 56F 1220 H-10291-N 3 /4" $ 207.85 56F 1240 H-10291-N 1" 224.50 56F 1280 H-10291-N 1 1 /2" 374.03 56F 1310 H-10291-N 2" 519.01 MARK III ORISEAL CURB VALVE FEMALE IP THREAD INLET & OUTLET 56F 5064 H-1500-2-N 3 /4" $ 127.34 56F 5065 H-1500-2-N 1" 135.32 MARK II ORISEAL STOP COPPER COMPR. INLET & FEMALE IP THREAD OUTLET 56F 5700 H-15172-N 3 /4" $ 89.53 56F 5705 H-15172-N 1" 151.16 MARK II ORISEAL CURB VALVE FLARE INLET & FEMALE IP THREAD OUTLET 56F 5710 H-15174-N 3 /4" $ 93.62 ORISEAL CURB VALVE FLARE INLET & FEMALE IP THREAD OUTLET 56F 5810 H-15176-N 3 /4" $ 216.48 56F 5830 H-15176-N 1" 244.51 ORISEAL CURB VALVE FLARE INLET & OUTLET 56F 5890 H-15201-N 3 /4" $ 225.43 56F 5891 H-15201-N 1" 279.03 56F 5892 H-15201-N 1 1 /2" 545.43 56F 5895 H-15201-N 2" 840.93 MARK II ORISEAL CURB VALVE FLARE INLET & OUTLET 56F 5920 H-15204-N 3 /4" $ 103.25 MARK II ORISEAL CURB VALVE COPPER COMPRESSION INLET & OUTLET 56F 5940 H-15209-N 3 /4" $ 101.92 56F 5942 H-15209-N 1" 168.45 MUELLER 300 TM BALL CURB VALVE FEMALE IP THREAD INLET & OUTLET 56F 0010 B-20283-N 1 1 /2" $ 255.07 56F 0020 B-20283-N 2" 371.31 CURB STOP FLARE INLET & FEMALE IP THREAD OUTLET 56F 5760 H-15175-N 1" $ 133.38 CURB STOP FLARE INLET & OUTLET 56F 5850 H-15200-N 3 /4" $ 101.74

-11 August 7, 2014 SERVICE COUPLINGS STRAIGHT SERVICE COUPLING COPPER FLARE TO OUTSIDE IRON PIPE THREAD 56F 7110 H-15425-N 1 /2" Copper Flare To Outside Iron Pipe Thread $ 24.73 56F 7130 H-15425-N 3 /4" Copper Flare To Outside Iron Pipe Thread 20.24 56F 7150 H-15425-N 3 /4" x 1" Copper Flare To Outside Iron Pipe Thread 23.35 56F 7170 H-15425-N 1" Copper Flare To Outside Iron Pipe Thread 28.93 56F 7190 H-15425-N 1 1 /4" Copper Flare To Outside Iron Pipe Thread 58.11 56F 7220 H-15425-N 1 1 /2" Copper Flare To Outside Iron Pipe Thread 89.90 56F 7240 H-15425-N 2" Copper Flare To Outside Iron Pipe Thread 164.97 H-15425 STRAIGHT SERVICE COUPLING MUELLER 110 CONDUCTIVE COMPRESSION TO OUTSIDE I.P. THREAD FOR TYPE K COPPER SERVICE OR PLASTIC PIPE WITH SAME OD 56F 7270 H-15428-N 3 /4" Mueller 110 Conductive Compression To Outside IP Thread $ 22.80 56F 7290 H-15428-N 1" Mueller 110 Conductive Compression To Outside IP Thread 26.93 56F 7291 H-15428-N 3 /4" x 1" Mueller 110 Conductive Compression To Outside IP Thread 23.57 56F 7292 H-15428-N 1 1 /4" Mueller 110 Conductive Compression To Outside IP Thread 52.01 56F 7293 H-15428-N 1 1 /2" Mueller 110 Conductive Compression To Outside IP Thread 74.48 56F 7295 H-15428-N 2" Mueller 110 Conductive Compression To Outside IP Thread 108.52 H-15428 STRAIGHT SERVICE COUPLING MUELLER 110 CONDUCTIVE COMPRESSION FOR IPS PE PIPE TO M.I.P. THREAD 56F 7310 H-15429-N 3 /4" Mueller 110 Cond. Compr. For IPS PE Pipe To M.I.P. Thread $ 27.99 56F 7311 H-15429-N 1" Mueller 110 Cond. Compr. For IPS PE Pipe To M.I.P. Thread 43.89 STRAIGHT SERVICE COUPLING COPPER FLARE TO INSIDE IRON PIPE THREAD 56F 7320 H-15450-N 1 /2" Copper Flare To Inside Iron Pipe Thread $ 33.17 56F 7340 H-15450-N 3 /4" Copper Flare To Inside Iron Pipe Thread 20.09 56F 7350 H-15450-N 3 /4" x 1" Copper Flare To Inside Iron Pipe Thread 31.64 56F 7380 H-15450-N 1" Copper Flare To Inside Iron Pipe Thread 30.64 56F 7410 H-15450-N 1 1 /4" Copper Flare To Inside Iron Pipe Thread 60.77 H-15429 H-15450 STRAIGHT SERVICE COUPLING MUELLER 110 CONDUCTIVE COMPRESSION TO INSIDE I.P. THREAD FOR TYPE K COPPER SERVICE OR PLASTIC PIPE WITH SAME OD 56F 7480 H-15451-N 3 /4" Mueller 110 Conductive Compression To Inside IP Thread $ 24.43 56F 7485 H-15451-N 1" x 3 /4" Mueller 110 Conductive Compression To Inside IP Thread 28.27 56F 7510 H-15451-N 1" Mueller 110 Conductive Compression To Inside IP Thread 34.93 56F 7511 H-15451-N 1 1 /4" Mueller 110 Conductive Compression To Inside IP Thread 59.79 56F 7513 H-15451-N 1 1 /2" Mueller 110 Conductive Compression To Inside IP Thread 95.24 56F 7514 H-15451-N 2" Mueller 110 Conductive Compression To Inside IP Thread 113.49 H-15451 STRAIGHT SERVICE COUPLING MUELLER 110 CONDUCTIVE COMPRESSION TO INSIDE I.P. THREAD FOR IPS PLASTIC PIPE 56F 7515 H-15454-N 3 /4" Mueller 110 Cond. Compr. To Inside I.P. Thread For IPS Plastic Pipe $ 38.44 56F 7520 H-15454-N 1" Mueller 110 Cond. Compr. To Inside I.P. Thread For IPS Plastic Pipe 38.44 STRAIGHT SERVICE COUPLING FLANGE TO COPPER WITH GASKET - FOR EXTRA STRONG LEAD FLANGE 56F 7775 H-15505-N 5 /8" x 3 /4" Flange To Copper With Gasket - For Extra Strong Lead Flange $ 31.71 H-15454 H-15505

August 7, 2014 SERVICE COUPLINGS STRAIGHT SERVICE COUPLINGS MUELLER PACK JOINT CONNECTIONS TO IPS PVC PIPE 56F 9000 V-15401-N 1" x 3 /4" Mueller Pack Joint Connections - Both Ends - For IPS PVC Pipe $ 51.92 56F 9730 V-15442-N 1" x 3 /4" Mueller Pack Joint Connection To F.I.P. Thread For IPS PVC Pipe $ 44.33 56F 9710 V-15440-N 1 1 /2" x 1 1 /2" Mueller Pack Joint Connection To M.I.P. Thread For IPS PVC Pipe $ 87.63 56F 9720 V-15440-N 2" x 2" Mueller Pack Joint Connection To M.I.P. Thread For IPS PVC Pipe 127.26 V-15401 V-15442-11A V-15440 1 /8 BEND SERVICE COUPLING SWIVEL NUT WITH INSIDE IRON PIPE THREAD TO COPPER - WITH GASKET 56F 7713 H-15486-N 3 /4" Swivel Nut With Inside Iron Pipe Thread To Copper - With Gasket $ 77.48 56F 7715 H-15486-N 1" Swivel Nut With Inside Iron Pipe Thread To Copper - With Gasket 88.01 1 /8 BEND SERVICE COUPLING FLANGE TO COPPER WITH GASKET - FOR EXTRA STRONG LEAD FLANGE 56F 7790 H-15516-N 5 /8" x 3 /4" Flange To Copper With Gasket - For Extra Strong Lead Flange $ 56.09 56F 7820 H-15516-N 3 /4" Flange To Copper With Gasket - For Extra Strong Lead Flange 60.77 56F 7840 H-15516-N 1" Flange To Copper With Gasket - For Extra Strong Lead Flange 104.77 H-15486 H-15516 1 /4 BEND SERVICE COUPLING COPPER FLARE TO INSIDE IRON PIPE THREAD 56F 7550 H-15460-N 3 /4" Copper Flare To Inside Iron Pipe Thread $ 38.77 56F 7560 H-15460-N 1" Copper Flare To Inside Iron Pipe Thread 60.93 1 /4 BEND SERVICE COUPLING COPPER FLARE TO COPPER FLARE 56F 7885 H-15525-N 3 /4" Copper Flare To Copper Flare $ 57.49 56F 7900 H-15525-N 1" Copper Flare To Copper Flare 77.09 1 /4 BEND SERVICE COUPLING MUELLER 110 CONDUCTIVE COMPRESSION CONNECTION FOR CTS OD - BOTH ENDS 56F 7910 H-15526-N 3 /4" Mueller 110 Cond. Compr. Connection For CTS OD - Both Ends $ 34.19 56F 7920 H-15526-N 1" Mueller 110 Cond. Compr. Connection For CTS OD - Both Ends 43.89 56F 7925 H-15526-N 1 1 /2" Mueller 110 Cond. Compr. Connection For CTS OD - Both Ends 149.06 56F 7930 H-15526-N 2" Mueller 110 Cond. Compr. Connection For CTS OD - Both Ends 301.58 1 /4 BEND SERVICE COUPLING COPPER FLARE TO OUTSIDE IRON PIPE THREAD 56F 7940 H-15530-N 3 /4" Copper Flare To Outside Iron Pipe Thread $ 20.64 56F 7960 H-15530-N 1" Copper Flare To Outside Iron Pipe Thread 34.32 1 /4 BEND SERVICE COUPLING MUELLER 110 CONDUCTIVE COMPRESSION CONNECTION FOR CTS OD TO OUTSIDE IRON PIPE THREAD 56F 7980 H-15531-N 3 /4" Mueller 110 Cond. Compr. Conn. For CTS OD To Outside I.P. Thrd $ 23.71 56F 7985 H-15531-N 1" Mueller 110 Cond. Compr. Conn. For CTS OD To Outside I.P. Thrd 40.96 H-15460 H-15525 H-15526 H-15530 H-15531

-11B August 7, 2014 SERVICE COUPLING SERVICE TEES SERVICE UNIONS 1 /4 BEND SERVICE COUPLING SWIVEL NUT WITH INSIDE MUELLER I.P. THREAD TO COPPER - WITH GASKET 56F 7750 H-15491-N 3 /4" Swivel Nut With Inside Mueller I.P. Thread To Copper - With Gasket $ 55.08 56F 7770 H-15491-N 1" Swivel Nut With Inside Mueller I.P. Thread To Copper - With Gasket 67.45 H-15491 SERVICE TEE COPPER TO COPPER TO COPPER 56F 6530 H-15380-N 3 /4" Copper To Copper To Copper $ 45.77 56F 6550 H-15380-N 1" Copper To Copper To Copper 80.75 56F 6630 H-15380-N 1" x 3 /4" Copper To Copper To Copper 89.21 SERVICE TEE COMPRESSION TO COMPRESSION TO COMPRESSION 56F 6670 H-15381-N 3 /4" Compression To Compression To Compression $ 63.95 56F 6690 H-15381-N 1" Compression To Compression To Compression 88.66 56F 6700 H-15381-N 1 1 /2" Compression To Compression To Compression 166.32 H-15380 H-15381 3 PART STRAIGHT COMPRESSION SERVICE UNION MUELLER 110 CONDUCTIVE COMPRESSION FOR TYPE K COPPER SERVICE OR PLASTIC PIPE WITH SAME OD - BOTH ENDS 56F 6890 H-15403-N 3 /4" Mueller 110 Conductive Compr Connection - Both Ends $ 27.81 56F 6895 H-15403-N 1" x 3 /4" Mueller 110 Conductive Compr Connection - Both Ends 30.68 56F 6920 H-15403-N 1" Mueller 110 Conductive Compr Connection - Both Ends 30.35 56F 6925 H-15403-N 1 1 /4" Mueller 110 Conductive Compr Connection - Both Ends 86.89 56F 6930 H-15403-N 1 1 /2" Mueller 110 Conductive Compr Connection - Both Ends 106.98 56F 6935 H-15403-N 2" Mueller 110 Conductive Compr Connection - Both Ends 144.49 H-15403 3 PART STRAIGHT COMPRESSION SERVICE UNION MUELLER 110 CONDUCTIVE COMPRESSION CONNECTION FOR PE PLASTIC PIPE (I.P.S.) - BOTH ENDS 56F 6940 H-15404-N 3 /4" Mueller 110 Cond Compr Conn. For PE Plastic Pipe (I.P.S) - Both Ends $ 34.72 56F 6950 H-15404-N 1" Mueller 110 Cond Compr Conn. For PE Plastic Pipe (I.P.S) - Both Ends 69.29 H-15404 3 PART STRAIGHT COMPRESSION SERVICE UNION MUELLER 110 CONDUCTIVE COMPRESSION CONNECTION FOR COPPER OR PE PLASTIC TUBE X PE PLASTIC PIPE (I.P.S) - BOTH ENDS 56F 7070 H-15409-N 3 /4" Mueller 110 Cond Compr Conn. For Copper or PE Tube x PE Pipe (I.P.S.) $ 63.21 56F 7080 H-15409-N 1" Mueller 110 Cond Compr Conn. For Copper or PE Tube x PE Pipe (I.P.S.) 78.39 2 PART SERVICE UNION COPPER FLARE NUT TO FEMALE COPPER FLARE THREAD 56F 6990 H-15405-N 3 /4" Copper Flare Nut To Female Copper Flare Thread $ 19.87 56F 7020 H-15405-N 1" Copper Flare Nut To Female Copper Flare Thread 32.68 56F 7060 H-15405-N 1 1 /2" Copper Flare Nut To Female Copper Flare Thread 128.46 3 PART SERVICE UNION COPPER FLARE NUT TO COPPER FLARE NUT 56F 6790 H-15400-N 3 /4" Copper Flare Nut To Copper Flare Nut $ 25.60 56F 6820 H-15400-N 1" Copper Flare Nut To Copper Flare Nut 44.81 56F 6840 H-15400-N 1 1 /4" Copper Flare Nut To Copper Flare Nut 92.68 56F 6860 H-15400-N 1 1 /2" Copper Flare Nut To Copper Flare Nut 135.57 H-15409

August 7, 2014 The Ford Meter Box Company, Inc. -11C 2 BRANCH "Y" CONNECTION COPPER FLARE NUT INLET TO COPPER FLARE NUT OUTLET - INLET & OUTLET CAN BE REVERSED 56F 6110 H-15340-N 1" x 1 1 /2" Copper Flare Nut Inlet To Copper Flare Nut Outlet $ 159.30 H-15340 2 BRANCH SHORT BODY "Y" CONNECTION MUELLER 110 CONDUCTIVE COMPRESSION CONNECTION FOR CTS OD TUBING - BOTH ENDS - INLET & OUTLET CAN BE REVERSED 56F 6150 H-15343-N 1" x 1 1 /2" Mueller 110 Cond. Compr Connection For CTS OD Tubing - Both Ends $ 139.93 H-15343 3 BRANCH "Y" CONNECTION COPPER FLARE NUT INLET TO M.I.P. THREAD OUTLET - INLET & OUTLET CAN BE REVERSED 56F 6270 H-15346-N 1" x 1 1 /2" Copper Flare Nut Inlet To M.I.P. Thread Outlet $ 216.50 H-15346 STAINLESS STEEL INSERT LINER/STIFFENERS SSC No. Manuf No. Connection Size Tubing/Pipe OD Range Tubing/Pipe OD Range Tubing/Pipe ID Range Price Each INSERT LINER/STIFFENER FOR POLYETHYLENE MUELLER 110 COMPRESSION CONNECTIONS 56F 7950 506139 1 1 /2" CTS 1.619" - 1.631" 0.181" - 0.199" 1.221" - 1.269" $ 6.12 56F 7975 506141 2" CTS 2.119" - 2.131" 0.236" - 0.260" 1.599" - 1.659" 10.64 INSERT LINER/STIFFENER FOR FOR POLYETHYLENE PB250 56F 8670 504281 3 /4" CTS 0.871" - 0.879" 0.097" - 0.107" 0.657" - 0.685" $ 2.92 56F 8720 504385 1" CTS 1.120" - 1.130" 0.125" - 0.137" 0.846" - 0.880" 3.13 INSERT LINER/STIFFENER FOR FOR POLYETHYLENE PB160 56F 8680 504305 3 /4" IPS $ 4.91 56F 8725 504391 1" IPS 8.66 INSERT LINER/STIFFENER FOR FOR PVC PLASTIC 56F 8730 505141 3 /4" IPS 1.045" - 1.110" 0.118" - 0.138" 0.809" - 0.834" $ 3.60 56F 8735 505142 1" IPS 1.329" - 1.399" 0.150" - 0.170" 1.029" - 1.059" 5.07 SERIES 70 INSERT LINER/STIFFENER FOR POLYETHYLENE (PEP) The Ford Meter Box Company, Inc. SSC No. Manuf No. Nominal Size PEP ID Price Each 56F 7800 INSERT-75 2" IPS 2.067" $ 6.63 GASKET & GRIPPER ASSEMBLY FOR MUELLER 110 COMPRESSION CONNECTIONS 56F 8940 581949 3 /4" For Mueller 110 Compression Connections $ 3.93 56F 8945 581951 1" For Mueller 110 Compression Connections 5.03 COPPER TUBE NUT 56F 7312 H-15430-N 3 /4" $ 7.41 56F 7313 H-15430-N 1" 9.36 FLARING TOOL 45 FLARE IN COPPER SERVICE PIPE 56F 8010 H-18000 3 /4" $ 40.45 56F 8030 H-18000 1" 51.44 56F 8040 H-18000 1 1 /4" 91.82

-12 August 7, 2014 RECORDALL DISC SERIES BRONZE WATER METERS RECORDALL LP DISC SERIES LO PROFILE METER BRONZE FOR SMALL TO INTERMEDIATE SERVICE APPLICATIONS LONG TERM FIELD PERFORMANCE FLOW RANGE FLEXIBILITY LOW PRESSURE LOSS 150 PSI MAX 80 F MAX SSC No. Manuf No. Size Register Length Operating Range Wgt Lbs. Price Each 56N 0300 LP 5 /8" x 1 /2" USG 7 1 /2" 1 /4 To 20 GPM 3.0 Lbs $ 77.81 56N 0310 LP 5 /8" x 3 /4" USG 7 1 /2" 1 /4 To 20 GPM 3.0 Lbs 68.00 56N 0320 LP 5 /8" x 1 /2" CF 7 1 /2" 1 /4 To 20 GPM 3.0 Lbs 65.27 56N 0330 LP 5 /8" x 3 /4" CF 7 1 /2" 1 /4 To 20 GPM 3.0 Lbs 65.27 Model LP RECORDALL M25 DISC SERIES WATER METER BRONZE FOR SMALL TO INTERMEDIATE SERVICE APPLICATIONS LONG TERM FIELD PERFORMANCE FLOW RANGE FLEXIBILITY LOW PRESSURE LOSS 150 PSI MAX 80 F MAX SSC No. Manuf No. Size Register Length Operating Range Wgt Lbs. Price Each 56N 0500 M25 5 /8" x 1 /2" USG 7 1 /2" 1 /2 To 25 GPM 4.5 Lbs $ 89.94 56N 0510 M25 5 /8" x 3 /4" USG 7 1 /2" 1 /2 To 25 GPM 4.5 Lbs 89.94 56N 0520 M25 5 /8" x 1 /2" CF 7 1 /2" 1 /2 To 25 GPM 4.5 Lbs 86.30 56N 0530 M25 5 /8" x 3 /4" CF 7 1 /2" 1 /2 To 25 GPM 4.5 Lbs 86.30 Model M25 RECORDALL M35 DISC SERIES WATER METER BRONZE FOR SMALL TO INTERMEDIATE SERVICE APPLICATIONS LONG TERM FIELD PERFORMANCE FLOW RANGE FLEXIBILITY LOW PRESSURE LOSS 150 PSI MAX 80 F MAX SSC No. Manuf No. Size Register Length Operating Range Wgt Lbs. Price Each 56N 0540 M35 3 /4" Short USG 7 1 /2" 3 /4 To 35 GPM 5.5 Lbs $ 128.19 56N 0550 M35 3 /4" Short CF 7 1 /2" 3 /4 To 35 GPM 5.5 Lbs 122.24 56N 0560 M35 3 /4" USG 9" 3 /4 To 35 GPM 5.5 Lbs 129.22 56N 0570 M35 3 /4" CF 9" 3 /4 To 35 GPM 5.5 Lbs 129.22 Model M35 RECORDALL M55 DISC SERIES WATER METER BRONZE FOR SMALL TO INTERMEDIATE SERVICE APPLICATIONS LONG TERM FIELD PERFORMANCE FLOW RANGE FLEXIBILITY LOW PRESSURE LOSS 150 PSI MAX 80 F MAX SSC No. Manuf No. Size Register Length Operating Range Wgt Lbs. Price Each 56N 0580 M55 1" USG 10 3 /4" 1 To 55 GPM 8.8 Lbs $ 199.72 56N 0590 M55 1" CF 10 3 /4" 1 To 55 GPM 8.8 Lbs 190.30 Model M55 RECORDALL M120 DISC SERIES WATER METER BRONZE FOR SMALL TO INTERMEDIATE SERVICE APPLICATIONS LONG TERM FIELD PERFORMANCE FLOW RANGE FLEXIBILITY LOW PRESSURE LOSS 150 PSI MAX 80 F MAX SSC No. Manuf No. Size Register Length Operating Range Wgt Lbs. Price Each 56N 0600 M120 1 1 /2" USG 13" 2 1 /2 To 120 GPM 19 Lbs $ 566.01 56N 0610 M120 1 1 /2" CF 13" 2 1 /2 To 120 GPM 19 Lbs 540.97 Model M120 RECORDALL M170 DISC SERIES WATER METER BRONZE FOR SMALL TO INTERMEDIATE SERVICE APPLICATIONS LONG TERM FIELD PERFORMANCE FLOW RANGE FLEXIBILITY LOW PRESSURE LOSS 150 PSI MAX 80 F MAX SSC No. Manuf No. Size Register Length Operating Range Wgt Lbs. Price Each 56N 0620 M170 2" USG 17" 2 1 /2 To 170 GPM 30 Lbs $ 846.36 56N 0630 M170 2" CF 17" 2 1 /2 To 170 GPM 30 Lbs 809.68 Model M170

August 7, 2014 RECORDALL WATER METERS TURBO & COMPOUND SERIES -12A RECORDALL T-160 TURBO SERIES WATER METER BRONZE FOR FOR COMMERCIAL & INDUSTRIAL APPLICATIONS MULTI-SYSTEM CAPATIBILITY EXTENDED FLOW RANGE LOWER PRESSURE LOSS 150 PSI MAX 120 F MAX SSC No. Manuf No. Size Register Length Operating Range Wgt Lbs. Price Each 56N 0640 T-160 1 1 /2" USG 13" 4 To 200 GPM 16.8 $ 1,007.12 Model T-160 RECORDALL T-200 TURBO SERIES WATER METER BRONZE FOR FOR COMMERCIAL & INDUSTRIAL APPLICATIONS MULTI-SYSTEM CAPATIBILITY EXTENDED FLOW RANGE LOWER PRESSURE LOSS 150 PSI MAX 120 F MAX SSC No. Manuf No. Size Register Length Operating Range Wgt Lbs. Price Each 56N 0650 T-200 2" USG 10" 4 To 310 GPM 16.4 $ 1,153.45 Model T-200 RECORDALL T-450 TURBO SERIES WATER METER BRONZE FOR FOR COMMERCIAL & INDUSTRIAL APPLICATIONS MULTI-SYSTEM CAPATIBILITY EXTENDED FLOW RANGE LOWER PRESSURE LOSS 150 PSI MAX 120 F MAX SSC No. Manuf No. Size Register Length Operating Range Wgt Lbs. Price Each 56N 0660 T-450 3" USG 12" 5 To 550 GPM 34.0 $ 1,375.54 Model T-450 RECORDALL T-1000 TURBO SERIES WATER METER BRONZE FOR FOR COMMERCIAL & INDUSTRIAL APPLICATIONS MULTI-SYSTEM CAPATIBILITY EXTENDED FLOW RANGE LOWER PRESSURE LOSS 150 PSI MAX 120 F MAX SSC No. Manuf No. Size Register Length Operating Range Wgt Lbs. Price Each 56N 0670 T-1000 4" USG 13" 10 To 1250 GPM 45.0 $ 2,074.49 Model T1000 RECORDALL 450 TURBO FIRE HYDRANT METER ALUMINUM HOUSING DOUBLE WALL STAINLESS STEEL SCREEN PROTECTS METERING ELEMENT BUILT-IN FLOW RESTRICTOR TO PREVENT ELEMENT OVERSPEEDING 150 PSI MAX SSC No. Manuf No. Size Register Length Operating Range Wgt Lbs. Price Each 56N 0680 450 3" USG 12" 5 To 660 GPM 17.2 $ 1,046.36 NOTE: END CONNECTIONS NOT INCLUDED IN PRICE. Model 450 For More Information On These Products Or On Products Not Listed, Call Salina Supply Company At (785) 823-2221 RECORDALL 2" COMPOUND SERIES WATER METER BRONZE & LOW LEAD ALLOY WIDEST OPERATING RANGE & EXTENDED LOW FLOW ACCURACIES THE SOLUTION FOR RAPIDLY CHANGING FLOW RATES. 150 PSI MAX 120 F MAX SSC No. Size Register Length Operating Range Wgt Lbs. Price Each 56N 0690 2" USG 1 1 /4" 1 /2 To 200 GPM 63.0 $ 2,537.59 2" Compound RECORDALL 3" COMPOUND SERIES WATER METER BRONZE & LOW LEAD ALLOY WIDEST OPERATING RANGE & EXTENDED LOW FLOW ACCURACIES THE SOLUTION FOR RAPIDLY CHANGING FLOW RATES. 150 PSI MAX 120 F MAX SSC No. Size Register Length Operating Range Wgt Lbs. Price Each 56N 0695 3" USG 17" 1 /2 To 450 GPM 99.5 $ 3,071.29 3" Compound

-13 August 7, 2014 COPPER METER YOKES COPPER METER YOKE WITH HORIZONTAL INLET & OUTLET LOCK WING 300 TM REDUCED PORT ANGLE BALL METER VALVE SSC No. Manuf No. Meter Size Price Each 56F 4020 B-2404-R-N 5 /8" x 7" Lock Wing Stop & Multi-Purpose Threads $ 128.05 56F 4025 B-2404-R-N 5 /8" x 12" Lock Wing Stop & Multi-Purpose Threads 132.21 56F 4030 B-2404-R-N 5 /8" x 3 /4" x 7" Lock Wing Stop & Multi-Purpose Threads 131.14 56F 4033 B-2404-R-N 5 /8" x 3 /4" x 12" Lock Wing Stop & Multi-Purpose Threads 139.56 56F 4040 B-2404-R-N 5 /8" x 3 /4" x 15" Lock Wing Stop & Multi-Purpose Threads 146.53 56F 4045 B-2404-R-N 5 /8" x 3 /4" x 18" Lock Wing Stop & Multi-Purpose Threads 162.90 B-2404-R 56F 4210 B-2404-R-N 1" x 10" Lock Wing Stop & Multi-Purpose Threads 259.94 56F 4220 B-2404-R-N 1" x 12" Lock Wing Stop & Multi-Purpose Threads 269.11 56F 4222 B-2404-R-N 1" x 15" Lock Wing Stop & Multi-Purpose Threads 280.27 COPPER METER YOKE WITH HORIZONTAL INLET & OUTLET WITH CHECK VALVE SSC No. Manuf No. Meter Size Price Each 56F 4035 H-2404-2-N 5 /8" x 3 /4" x 12" With Check Valve $ 195.21 H-2404-2 COPPER METER YOKE WITH VERTICAL INLET & OUTLET LOCK WING 300 TM REDUCED PORT ANGLE BALL METER VALVE SSC No. Manuf No. Meter Size Price Each 56F 4225 B-2410-R-N 5 /8" x 7" Lock Wing Stop & Multi-Purpose Threads $ 167.78 56F 4230 B-2410-R-N 5 /8" x 3 /4" x 7" Lock Wing Stop & Multi-Purpose Threads 128.05 56F 4233 B-2410-R-N 1" x 10" Lock Wing Stop & Multi-Purpose Threads 243.15 B-2410-R COPPER METER YOKE WITH HORIZONTAL INLET & OUTLET LOCK WING 300 TM REDUCED PORT ANGLE BALL METER VALVE SSC No. Manuf No. Meter Size Price Each 56F 4235 B-2434-R-N 5 /8" x 3 /4" x 7" With Lock Wing Stop & I.P. Threads $ 145.49 56F 4300 B-2434-R-N 5 /8" x 3 /4" x 12" With Lock Wing Stop & I.P. Threads 156.81 B-2434-R COPPER METER YOKE LOCK WING 300 TM ANGLE BALL METER VALVE ON INLET & OUTLET 1 1 /2" BYPASS VALVE SSC No. Manuf No. Meter Size Price Each 56F 0025 B-2423-N 2" x 18" $ 1,693.69 B-2423 COPPER METER YOKE - RELOCATOR TYPE VERTICAL INLET & OUTLET LOCK WING 300 TM REDUCED PORT ANGLE BALL METER VALVE SSC No. Manuf No. Meter Size Price Each 56F 4350 B-24118-R-N 5 /8" x 12" M.I.P. Meter Thread Ends $ 151.93 56F 4448 B-24118-R-N 5 /8" x 3 /4" x 7" M.I.P. Meter Thread Ends 145.48 56F 4450 B-24118-R-N 5 /8" x 3 /4" x 12" M.I.P. Meter Thread Ends 156.81 56F 4455 B-24118-R-N 5 /8" x 3 /4" x 18" M.I.P. Meter Thread Ends 180.10 56F 4460 B-24118-R-N 1" x 12" M.I.P. Meter Thread Ends 316.03 B-24118-R COPPER METER YOKE - BASEMENT TYPE VERTICAL INLET & OUTLET PLAIN YOKE SSC No. Manuf No. Meter Size Price Each 56F 4470 H-1412-N 5 /8" Multi-Purpose Threads $ 74.60 56F 4480 H-1412-N 1" Multi-Purpose Threads 134.52