MICRO MINI LATHE 4 X 5 Model 95012 ASSEMBLY AND OPERATING INSTRUCTIONS Due to continuing improvements, actual product may differ slightly from the product described herein. 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our Web site at: http://www.harborfreight.com TO PREVENT SERIOUS INJURY, READ AND UNDERSTAND ALL WARNINGS AND INSTRUCTIONS BEFORE USE. Copyright 2006 by Harbor Freight Tools. All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. For technical questions, please call 1-800-444-3353.
PRODUCT SPECIFICATIONS Item Description Electrical Requirements 110 VAC / 60 Hz / 150 Watts / 1.4 No Load Amps / 0.6 Start Up Amps 1/5 HP Motor Fuse Type: F2AL250V Power Cord Type: 18AWG x 3C / 4-7 Long Power Plug Type: 3-Prong, Grounded Variable Speed Capacity 0 to 3800 RPM Chuck Type 3-Jaw Self-Centering Chuck Capacity 1-3/4 Tool Post Capacity 7/16 Hole Through Spindle 13/32 (10mm) Swing Over Bed 4 Distance Between Centers 5 Cross Slide Scale 0.002 Per Each Mark Longitude Feed Scale 0 to 2 Per Each Mark Tail Stock Quill Travel 1 Tail Stock Quill Scale 0.002 Per Each Mark Bed Dimensions 14 Long x 3-5/16 Wide x 5 High Overall Dimensions 17.35 x 10.63 x 8.27 Additional Features Lockable Tool Post / Lockable Tail Stock / Hardened Bed Ways Net Weight 30.80 Lb. SAVE THIS MANUAL You will need this manual for the safety warnings and precautions, assembly, operating, inspection, maintenance and cleaning procedures, parts list and assembly diagram. Keep your invoice with this manual. Write the invoice number on the inside of the front cover. Keep this manual and invoice in a safe and dry place for future reference. GENERAL SAFETY RULES IMPORTANT SAFETY INSTRUCTIONS WARNING! READ AND UNDERSTAND ALL INSTRUCTIONS Failure to follow all instructions detailed in this manual may result in serious personal injury. SAVE THESE INSTRUCTIONS WORK AREA 1. Keep your work area clean and well lit. Cluttered and dark work areas invite accidents. 2. Do not operate electrically powered tools and equipment in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. SKU 95012 For technical questions, please call 1-800-444-3353 PAGE 2
PERSONAL SAFETY 3. Stay alert. Watch what you are doing, and use common sense when operating a power tool. Do not use the Micro Mini Lathe while tired or under the influence of drugs, alcohol, or medication. A moment of inattention while operating electrically powered tools and equipment may result in serious personal injury. 4. Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your hair, clothing, and gloves away from moving parts. Loose clothes, jewelry, or long hair can be caught in moving parts. 5. Do not overreach. Keep proper footing and balance at all times. Proper footing and balance enables better control of the Micro Mini Lathe in unexpected situations. 6. Always wear eye protection. Wear ANSI approved safety impact goggles when using this product. TOOL USE AND CARE 7. Do not force the Micro Mini Lathe. Use the correct product for your application. The correct product will do the job better and safer at the rate for which it is designed. 8. Store idle tools and equipment out of reach of children and other untrained people. Tools and equipment are dangerous in the hands of untrained users. 9. Maintain the Micro Mini Lathe with care. Keep this product clean. A properly maintained tool is easier to control. Do not use damaged tools and equipment. Tag damaged tools and equipment Do not use until repaired. 10. Check for misalignment or binding of moving parts, loose or broken parts, and any other condition that may affect the Micro Mini Lathe s operation. If damaged, have the Lathe serviced before using. Many accidents are caused by poorly maintained tools and equipment. 11. Use only accessories that are recommended by the manufacturer for your model. Accessories that may be suitable for one product may become hazardous when used on another product. SERVICE 12. Product service must be performed only by qualified service technician. SKU 95012 For technical questions, please call 1-800-444-3353 PAGE 3
Service or maintenance performed by unqualified personnel could result in a risk of injury. 13. When servicing the Micro Mini Lathe, use only identical replacement parts. Follow instructions in the Inspection, Maintenance, And Cleaning section of this manual. Use of unauthorized parts or failure to follow maintenance instructions may create a risk of electric shock or injury. SPECIFIC SAFETY RULES 1. Maintain labels and nameplates on the Micro Mini Lathe. These carry important information. If unreadable or missing, contact Harbor Freight Tools for a replacement. 2. Use the right product for the job. There are certain applications for which this product was designed. Do not use small tools, equipment, or attachments to do the work of larger industrial tools, equipment, or attachments. Do not use this product for a purpose for which it was not intended. 3. Store idle tools. When not in use, store the Micro Mini Lathe in a clean, dry, safe location out of reach of children. 4. This product is designed for indoor use only. Do not expose this product to rain. 5. Do not unplug the Micro Mini Lathe by pulling on its Power Cord. Do not pull or carry the Lathe by its Power Cord. Keep the Power Cord away from sharp corners or edges. Always disconnect the Power Cord from its electrical outlet by grasping and pulling on the Power Cord s Plug. 6. Reduce the risk of accidental starting. Make sure the Power Switch is in its OFF position before plugging the Power Cord into a 110 volt, grounded, electrical outlet. 7. Make sure all adusting wrenches are removed from the Micro Mini Lathe prior to turning on the machine. 8. Keep all safety guards in proper working order, proper adjustment, and proper alignment. 9. Make sure the workpiece is securely mounted in the Micro Mini Lathe be fore turning on the machine. An excessively loose workpiece can fly off the Lathe, causing severe personal injury and/or property damage. 10. Industrial applications must follow OSHA requirements. SKU 95012 For technical questions, please call 1-800-444-3353 PAGE 4
11. Always keep hands and fingers as far away as possible from the moving parts of the Micro Mini Lathe. Do not reach over or across the Lathe when it is running. 12. Allow the workpiece to turn up to full speed before feeding a tool bit (not included) into the workpiece. When turning off the Micro Mini Lathe, allow the workpiece to slow down and stop on its own. Do not press against the workpiece to stop it. 13. Feed the tool bit into the workpiece gradually. Do not force a tool bit to remove material faster than it is designed to cut. 14. Never attempt to remove material stuck in the moving parts of the Micro Mini Lathe while it is plugged in and running. 15. Make sure the workbench on which the Micro Mini Lathe will be placed is flat, level, dry, and sturdy enough to handle the weight of the Lathe, its accessories, any additional tools, and the workpieces. 16. Always turn the Power Switch to its OFF position and unplug the Power Cord/Plug from its electrical outlet prior to making any adjustments to the machine or performing any maintenance or cleaning procedures. 17. WARNING! Some dust created by power sanding, sawing, grinding, drilling, and other construction activities, contain chemicals known (to the State of California) to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: lead from lead-based paints, crystalline silica from bricks and cement or other masonry products, arsenic and chromium from chemically treated lumber. Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles. (California Health & Safety Code 25249.5, et seq.) 18. WARNING! People with pacemakers should consult their physician(s) before using this product. Operation of electrical equipment in close proximity to a heart pacemaker could cause interference or failure of the pacemaker. 19. WARNING! The warnings and cautions discussed in this manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. SAVE THESE INSTRUCTIONS SKU 95012 For technical questions, please call 1-800-444-3353 PAGE 5
GROUNDING WARNING! Improperly connecting the grounding wire can result in the risk of electric shock. Check with a qualified electrician if you are in doubt as to whether the outlet is properly grounded. Do not modify the power cord plug provided with the tool. Never remove the grounding prong from the plug. Do not use the tool if the power cord or plug is damaged. If damaged, have it repaired by a service facility before use. If the plug will not fit the outlet, have a proper outlet installed by a qualified electrician. GROUNDED TOOLS: TOOLS WITH THREE PRONG PLUGS 1. Tools marked with Grounding Required have a three wire cord and three prong grounding plug. The plug must be connected to a properly grounded outlet. If the tool should electrically malfunction or break down, grounding provides a low resistance path to carry electricity away from the user, reducing the risk of electric shock. (See Figure A.) 2. The grounding prong in the plug is connected through the green wire inside the cord to the grounding system in the tool. The green wire in the cord must be the only wire connected to the tool s grounding system and must never be attached to an electrically live terminal. (See Figure A.) 3. Your tool must be plugged into an appropriate outlet, properly installed and grounded in accordance with all codes and ordinances. The plug and outlet should look like those in the following illustration. (See Figure A.) THIS PRODUCT USES A 3-PRONG PLUG 120 VOLT, GROUNDED, ELECTRICAL OUTLET FIGURE A SKU 95012 For technical questions, please call 1-800-444-3353 PAGE 6
DOUBLE INSULATED TOOLS: TOOLS WITH TWO PRONG PLUGS 4. Tools marked Double Insulated do not require grounding. They have a special double insulation system which satisfies OSHA requirements and complies with the applicable standards of Underwriters Laboratories, Inc., the Canadian Standard Association, and the National Electrical Code. (See Figure B.) 5. Double insulated tools may be used in either of the 120 volt outlets shown in the following illustration. (See Figure B.) THIS PRODUCT DOES NOT USE A 2-PRONG PLUG 120 VOLT, GROUNDED, ELECTRICAL OUTLETS FIGURE B EXTENSION CORDS 1. Grounded tools require a three wire extension cord. Double Insulated tools can use either a two or three wire extension cord. 2. As the distance from the supply outlet increases, you must use a heavier gauge extension cord. Using extension cords with inadequately sized wire causes a serious drop in voltage, resulting in loss of power and possible tool damage. (See Figure C, next page.) 3. The smaller the gauge number of the wire, the greater the capacity of the cord. For example, a 14 gauge cord can carry a higher current than a 16 gauge cord. (See Figure C.) 4. When using more than one extension cord to make up the total length, make sure each cord contains at least the minimum wire size required. (See Figure C.) 5. If you are using one extension cord for more than one tool, add the nameplate SKU 95012 For technical questions, please call 1-800-444-3353 PAGE 7
amperes and use the sum to determine the required minimum cord size. (See Figure C.) 6. Make sure your extension cord is properly wired and in good electrical condition. Always replace a damaged extension cord or have it repaired by a qualified electrician before using it. 7. Protect your extension cords from sharp objects, excessive heat, and damp or wet areas. RECOMMENDED MINIMUM WIRE GAUGE FOR EXTENSION CORDS* (110 VOLT) FIGURE C *Based on limiting the line voltage drop to five volts at 150% of the rated amperes. SYMBOLOGY FIGURE D SKU 95012 For technical questions, please call 1-800-444-3353 PAGE 8
UNPACKING When unpacking, check to make sure all the parts shown in the Parts List on page 19 are included. If any parts are missing or broken, please call Harbor Freight Tools at the number shown on the front cover of this manual as soon as possible. PRODUCT FEATURES Part # Description Part # Description 1 Bed Way 62 Emergency Stop Button 17 Base 63 Variable Speed Control Knob 23A Tail Stock Hand Wheel 64 Automatic Overload Light (Yellow) 23B Lead Screw Hand Wheel 65 Power On Light (Green) 23C Saddle Hand Wheel 67 Fuse Holder 29 Dust Guard 70 Chuck Protective Cover 30 3-Jaw Chuck 79 Tool Rest 41 Head Stock 90 Tail Stock 29 41 63 70 30 79 23C 90 23A 1 23B 17 67 64, 65 62 FIGURE E SKU 95012 For technical questions, please call 1-800-444-3353 PAGE 9
1. The Bed Way (1) is especially hardened which ensures rigidity and low vibration. The Head Stock (41), Tail Stock (90), and Lead Screw (94) are mounted on the Bed Way. (See Figure E.) 2. The Dust Guard (29) is mounted on the left side of the Head Stock (41) and Bed Way (1). The Dust Guard protects the Motor (58), V-Belt (48), and V-Pulley (49). (See Figure E and Assy. Diagram.) 3. The 3-Jaw Chuck (30) is self-centering and is mounted on the Spindle (31). To remove the Chuck, simply remove the three securing Nuts to the rear of the Spindle. This allows the Chuck to be pulled free along with its three mounting Studs. (See Figure E.) 4. Within the Head Stock (41) is the Motor (58). The Motor provides a direct drive to the Spindle (31) via the internal V-Belt (48), and is regulated by the Variable Speed Control Knob (63). (See Figure E.) 5. The Emergency Stop Button (62) is located on the Head Stock (41), and is activated by pressing down on the Button. (See Figure E.) 6. The Variable Speed Control Knob (63) is also located on the Head Stock (41). To turn on the Micro Mini Lathe, turn the Variable Speed Control Knob clockwise. A click will be heard as power is turned on, but the Spindle (31) will not rotate until the Knob is turned clockwise a little further. Speed will increase progressively the further the Knob is turned. To turn off the Lathe, turn the Variable Speed Control counterclockwise. (See Figure E.) 7. The Automatic Overload Light (64) is yellow in color. The power supply system of this Lathe has an automatic overload protective device. If cutting or drilling too deep, the system will stop working, and the yellow Light will illuminate. Should this occur, turn off the Variable Speed Control Knob (63), and then turn it on again. The system will operate once again, and the yellow Light will turn off automatically. (See Figure E.) 8. The Power On Light (65) is green in color and will illuminate when the Variable Speed Control Knob (63) is turned clockwise to turn on the Lathe. (See Figure E.) 9. The Fuse Holder (67) is located at the back of the Lathe. Should the Lathe not turn on, check to make sure the machine s Power Cord/Plug (16) is connected to a working, 110 volt, grounded outlet. Then make sure to turn the Variable Speed Control Knob (63) clockwise. Should the Lathe still not turn on, disconnect the Power Cord/Plug from its electrical outlet. Use a phillips screwdriver to open the Fuse Holder and inspect the Fuse (114) for damage. If necessary, replace the Fuse (type: F2AL250V). Then, close the Fuse Holder. (See Figure E.) SKU 95012 For technical questions, please call 1-800-444-3353 PAGE 10
10. The Chuck Protective Cover (70) must always be fully lowered prior to turning on the Micro Mini Lathe. The Chuck Protective Cover helps prevent metal/wood shavings and coolant (if used) from being thrown out toward the operator. (See Figure E.) 11. The Tool Rest (79) must be used with cutting tools (not included) that can be properly mounted to the Rest, with as little overhang of the tool as possible. Ideally, the overhang should be approximately 1/4 to 3/8 for a straight cutting tool. A cutting tool can be secured in the Tool Rest using the three Hex Socket Head Screws (3, 34) located at the top of the Tool Rest. (See Figure E.) 12. The Tail Stock (90) may be moved along the Bed Way (1) to any desired position, and is secured in position with the Screw (81) located at the front of the Tail Stock. (See Figure E.) 13. The Saddle Hand Wheel (23C) operates the Saddle (103), onto which is mounted the Tool Rest (79). Adjusting the Saddle and Tool Rest allows for intricate and delicate operations to be performed. (See Figure E.) ASSEMBLY INSTRUCTIONS 1. Assembly requires attaching the Tail Stock Hand Wheel (23A), Lead Screw Hand Wheel (23B), and Saddle Hand Wheel (23C) to the Lathe. Each Hand Wheel is identical to the others in size and construction. To secure the Hand Wheels, use one Cap Nut (24) for each Hand Wheel. (See Figure E.) 2. The Chuck Protective Cover (70) must also be attached to the Lathe. To do so, align the two mounting holes in the Chuck Protective Cover with the two threaded mounting holes in the Rotator Shaft (71). Then secure the Chuck Protective Cover to the Rotator Shaft, using two Screws (69). (See Figure E and Assy. Diagram.) MOUNTING THE MICRO MINI LATHE 1. CAUTION! Make sure the workbench on which the Micro Mini Lathe will be placed is flat, level, dry, and sturdy enough to handle the weight of the Lathe, its accessories, any additional tools, and the workpieces. 2. Mount the Lathe on a workbench of sufficient height so that you do not need to bend your back to perform normal operations. 3. Make sure the location is adequately lit, and that you will not be working in your own shadow. SKU 95012 For technical questions, please call 1-800-444-3353 PAGE 11
SET-UP INSTRUCTIONS 1. The following Steps are guidelines on how to set up the Micro Mini Lathe in order to perform a simple turning operation. 2. Always plan your work. Have drawings or a plan on hand along with any measuring instruments you may require such as, micrometers, verniers, calipers, etc. 3. Select a cutting tool (not included) that will produce the desired cut. Mount the cutting tool in the Tool Rest (79) with approximately 1/4 to 3/8 overhang from the Tool Rest. 4. IMPORTANT: Make sure the tip of the cutting tool is on the center line of the work, or just slightly below it. If necessary, shims (not included) should be used beneath the cutting tool to achieve the proper height. To ensure the tip of the cutting tool is at the proper height, position the tool so that its tip is almost touching the point of the Tail Stock (90) center. If necessary, make adjustments using the shims. 5. Securely mount the workpiece between the 3-Jaw Chuck (30) and the Tail Stock (90). NOTE: If the Tail Stock is not to be used, you may remove the Screw (81) that secures the Tail Stock in place. Then, slide the Tail Stock off the Bed Way (1). 6. Mark the surface of the workpiece at the point where the cut is to end. Move the Saddle (103) so that the cutting tool is directly opposite the mark. Then, turn the Saddle Hand Wheel (23C) so that the cutting tool touches the surface of the workpiece. 7. Rotate the 3-Jaw Chuck (30) by hand to ensure it will not come into contact with anything (i.e., Saddle, Tool Rest, cutting tool, etc.) when the machine is turned on. 8. Turn the Saddle Hand Wheel (23C) to retract the cutting tool away from the workpiece. Use the 3-Jaw Chuck to rotate the workpiece by hand. At any point along the length of the workpiece to be cut, move the cutting tool slowly until it just touches the surface. Record this position by zeroing the Scale. Example: Turn the moveable Scale until the cutting tool is a short distance from the right hand edge of the workpiece. Move the Saddle Hand Wheel (23C) one full turn until the zero marks again coincide. (See Figure F, next page.) IMPORTANT: If you go past the zero marks on the Scale, back off again at least one-half turn of the Saddle Hand Wheel (23C). Then, slowly bring the marks back together. (See Figure F, next page.) SKU 95012 For technical questions, please call 1-800-444-3353 PAGE 12
SCALE SADDLE HAND WHEEL (23C) FIGURE F 9. Continue turning the Saddle Hand Wheel (23C) an amount equivalent to your desired depth of cut. NOTE: It is recommended that for rough cutting, you do not exceed 0.010 as your depth of cut. OPERATING INSTRUCTIONS 1. Use the Lead Screw Hand Wheel (23B) and Saddle Hand Wheel (23C) to move the cutting tool to its cutting position. Make sure the cutting tool does not contact the workpiece. 2. Make sure the Variable Speed Control Knob (63) is in its OFF position. Then plug the Power Cord/Plug (16) into the nearest 110 volt, grounded, electrical outlet. 3. Turn the Variable Speed Control Knob (63) clockwise to its ON position. Then, adjust the Variable Speed Control Knob to achieve the desired turning speed of the workpiece. 4. Allow sufficient time for the workpiece to reach the desired turning speed. Then slowly and carefully, use the Lead Screw Hand Wheel (23B) and Saddle Hand Wheel (23C) to move the cutting tool in order to make the desired cuts on the workpiece. IMPORTANT: Your left hand should always be free in order to hit the Emergency Stop Button (62) should it become necessary. 5. Do not force the Micro Mini Lathe or cutting tool to remove material faster than they are designed to cut. Make sure to feed the cutting tool gradually into the workpiece. 6. Once the turning job is completed, turn the Variable Speed Control Knob (63) counterclockwise to turn off the machine. Wait until the workpiece stops turning. Then, unplug the Power Cord/Plug (16) from its electrical outlet. 7. Make sure to store the Micro Mini Lathe in a clean, dry, safe location out of reach of children and other unauthorized people SKU 95012 For technical questions, please call 1-800-444-3353 PAGE 13
Middle Saddle Adjustments: SETTINGS AND ADJUSTMENTS 1. The Middle Saddle (106) is mounted on the Saddle (103). Between the sloping surfaces on one side of the Middle Saddle a jib strip is inserted, which may be tightened against the Saddle with the three adjuster or jib Screws (91, 92) and three Nuts (18) mounted along its length. (See Figure G.) 2. The three jib Screws (91, 92) are located on the right side of the Middle Saddle (106). In time, wear will occur on the inner surfaces of the Middle Saddle and Saddle (103) resulting in a sloppiness of action. To adjust the jib strip to account for wear and to ensure the Middle Saddle moves evenly and smoothly along the Saddle, proceed as follows: A. Loosen the three Nuts (18), and screw in the three jib Screws (91, 92) evenly. The Middle Saddle (106) should be held against the Saddle (103) firmly. Test by attempting to turn the Saddle Hand Wheel (23C), but do not force it. (See Figure G.) B. Screw out each of the three jib Screws (91, 92) by one quarter of a turn only. Then, retighten the Nuts (18). (See Figure G.) C. Test again by turning the Saddle Hand Wheel (23C). The sliding movement of the Middle Saddle (106) should be even and smooth along its complete length. (See Figure G.) D. If the movement is too slack, screw all jib Screws (91, 92) in by one eighth of a turn. Then, re-try. If the movement is too stiff, screw out the jib Screws by one eighth of a turn until the proper adjustment is obtained. (See Figure G.) E. Tighten all three Nuts (18), taking care not to move the jib Screws (91, 92) while doing so. (See Figure G.) F. When finished, retract the Middle Saddle (106) fully and apply machine oil to all mating surfaces. Then, move the Middle Saddle to its normal position. (See Figure G.) JIB STRIP FIGURE G MIDDLE SADDLE (106) NUT (18) JIB SCREW (91, 92) SADDLE (103) SKU 95012 For technical questions, please call 1-800-444-3353 PAGE 14
Tail Stock Adjustments: 1. The Tail Stock (90) is held in position on the Bed Way (1) by one Screw (81). By loosening the Screw, the Tail Stock may be moved to the left or right at any point along the Bed Way. Once the Tail Stock is moved, make sure to retighten the Screw. (See Figure E.) INSPECTION, MAINTENANCE, AND CLEANING 1. CAUTION! Make sure the Variable Speed Control Knob (63) is in its OFF position and the Power Cord/Plug (16) is unplugged from its electrical outlet before performing any inspection, maintenance, or cleaning of the Micro Mini Lathe. 2. Before each use, inspect the general condition of the Micro Mini Lathe. Check for misalignment or binding of moving parts, damaged or loose parts, damaged electrical wiring, and any other condition that may affect the tool s safe operation. If a problem occurs, have the problem corrected before further use. Do not use damaged equipment. 3. Before each use: Apply a few drops of machine oil into the Lead Screw Left Support (2) and Lead Screw Right Support (22). Lubricate twice if the machine is operated continuously during the day. (See Assy. Diagram.) 4. Before each use: Apply a few drops of machine oil into the Middle Saddle (106). The oil fill hole is located on the top surface of the Middle Saddle. 5. To change the V-Belt: The V-Belt (48) is located within the Pulley Cover (42). To change the V-Belt, open the Pulley Cover. Slip the old V-Belt off the two V-Pulleys (38, 48). Install a new V-Belt of the same size and type on the V-Pulleys. Then, close the Pulley Cover. (See Figure H.) V-BELT (48) V-PULLEY (38) PULLEY COVER (42) FIGURE H V-PULLEY (48) SKU 95012 For technical questions, please call 1-800-444-3353 PAGE 15
6. To replace the Motor Carbon Brushes: It may become necessary at sometime to replace or clean the two Carbon Brushes (58A) when the Motor (58) performance decreases, or stops working completely. The Carbon Brushes are located on each side of the Motor Housing. To replace the Carbon Brushes: A. Open the Pulley Cover (42), and remove the V-Belt (48). (See Figure I.) B. Remove the V-Pulley (49). (See Figure I.) C. Unscrew and remove the four Screws (51) that secure the Motor to the Body of the machine. (See Figure I.) D. From the back of the Lathe, pull the Motor slightly out to expose the two Carbon Brush Holder Covers located on the side of the Motor Housing. (See Figure I.) E. Remove the two Brush Holder Covers. Then, remove the two Carbon Brushes. (See Figure I.) F. If the Carbon Brushes (58A) are worn down more than 1/2, replace both Carbon Brushes. If, however, the Carbon Brushes are just dirty they may be cleaned by rubbing them with a pencil eraser. When installing the new Carbon Brushes, make sure the carbon portion of the Carbon Brushes contact the Motor s Rotor and that the springs face away from the Motor. Also, make sure the springs operate freely. After replacement or cleaning, replace the two Brush Holder Covers. NOTE: New Carbon Brushes tend to arc or spark when first used until they wear and conform to the Motor s Rotor. (See Figure I.) SCREW (51) SCREW (51) V-PULLEY (49) CARBON BRUSH (58A) MOTOR (58) PULLEY COVER (42) SCREW (51) SCREW (51) V-BELT (48) FIGURE I SKU 95012 For technical questions, please call 1-800-444-3353 PAGE 16
G. Once the two Carbon Brushes (58A) have been cleaned or replaced, place the Motor (58) back into the Body of the Lathe. Align the four threaded mounting holes in the Motor with the four mounting holes in the Body. Then secure the Motor to the Body with the four previously removed Screws (51). (See Figure I.) H. Re-install the V-Pulley (49) and V-Belt (48). Then, close the Pulley Cover (42) securely. (See Figure I.) 7. To replace the Fuse: The Fuse Holder (67) is located at the back of the Lathe. Should the Lathe not turn on, check to make sure the machine s Power Cord/ Plug (16) is connected to a working, 110 volt, grounded outlet. Then make sure to turn the Variable Speed Control Knob (63) clockwise. Should the Lathe still not turn on, disconnect the Power Cord/Plug from its electrical outlet. Use a phillips screwdriver to open the Fuse Holder and inspect the Fuse for damage. If necessary, replace the Fuse (type: F2AL250V). Then, close the Fuse Holder. (See Figure J.) FUSE FIGURE J 8. To clean: Use a mild solvent to clean the Micro Mini Lathe. If a coolant has been used, make sure it is completely drained from the Tray of the machine. 9. When storing: Make sure to store the Micro Mini Lathe in a safe, dry, clean location out of reach of children and other unauthorized people. 10. CAUTION! All maintenance, service, and repairs not discussed in this manual should only be performed by a qualified service technician. SKU 95012 For technical questions, please call 1-800-444-3353 PAGE 17
TROUBLESHOOTING Problem Possible Cause Possible Solution 1. Cutting tool is above workpiece center line. 1. Lower cutting tool to center line of workpiece. Quality of cut is poor. (Rough or torn surface) 2. Lathe speed too slow. 2. Use the Variable Speed Control Knob to increase lathe speed. Excessive vibration when turning thin workpieces. Excessive vibration when turning larger workpieces or bowls. Lathe will not turn on. Lathe will not turn off. 3. Cutting tool is too dull. 4. Cutting too aggressively. 1. Cutting tool is positioned below the workpiece center line. 2. Cutting too aggressively. 1. Head Stock and/or Tail Stock improperly located at ends of workpiece. 2. Workpiece is unbalanced. 1. Variable Speed Control Knob is in its OFF position. 2. Electrical outlet not charged or is of wrong voltage. 3. Blown Fuse. 4. Faulty Carbon Brushes. 1. Damaged or faulty Variable Speed Control Knob and/or internal electrical wiring. 3. Replace the cutting tool. 4. Use a lighter touch. 1. Raise the cutting tool to the workpiece center line. 2. Use a lighter touch. 1. Check for proper workpiece centers. 2. Cut off stock until workpiece is balanced. 1. Make sure Variable Speed Control Knob is turned clockwise to its ON position. 2. Make sure Lathe is plugged into a working, 110 volt, grounded, electrical outlet. 3. Replace Fuse. 4. Clean or replace Carbon Brushes. 1. Unplug the Power Cord/Plug from its electrical outlet immediately. Do not operate Lathe until it is repaired by a qualified service technician. PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEI- THER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACE- MENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISKS AND LIABILITY ARIS- ING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACE- MENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO. SKU 95012 For technical questions, please call 1-800-444-3353 PAGE 18
PARTS LIST Part # Description Qty. Part # Description Qty. 1 Bed Way 1 60 Screw (ST2.9 x 9.5) 4 2 Lead Screw (Left Support) 1 61 Electric Box Cover 1 3 Screw(M6 x 14) 10 62 Emergency Stop Button 1 4 Lead Screw Protective Cover 1 63 Variable Speed Control Knob 1 5 Screw (M4 x 6) 1 64 Yellow Lamp 1 6 Screw (ST2.9 x 6.5) 3 65 Green Lamp 1 7 Screw (M3 x 8) 4 66 Variable Speed Control 1 8 PC Board 1 67 Fuse Holder 1 9 Electricity Fixed Plate 1 68 Plastic Tube 1 10 Screw (M6 x 12) 6 69 Screw (M4 x 8) 2 11 Rubber Pad 4 70 Chuck Protective Cover 1 12 Nut (M6) 6 71 Rotator Shaft 1 13 Small Washer (#6) 10 72 Key (3 x 6) 1 14 Switch Label 1 73 Spacer 1 15 Lock Connect 2 74 Compress Spring (L=16) 1 16 Power Cord/Plug 1 75 Screw (M2 x 20) 2 17 Base 1 76 Micro Switch 1 18 Nut (M4) 5 77 Nut (M2) 2 19 Spring Washer (#4) 7 78 Electric Box 1 20 Screw (M4 x 10) 3 79 Tool Rest 1 21 Lead Screw 1 80 Screw (M4 x 6) 1 22 Lead Screw (Right Support) 1 81 Screw (M6 x 35) 1 23 Hand Wheel 3 82 Tail Stock Shaft 1 24 Cap Nut (M5) 3 83 Screw (M6 x 16) 1 25 Rotator (Small Handle) 3 84 Set Screw 1 26 Handle Screw 3 85 Set Screw (M6 x 8) 1 27 Screw (M4 x 6) 11 86 Tail Stock Shaft Lead Screw 1 28 Flat Washer (#4) 6 87 Small Handle 2 29 Dust Guard 1 88 Nesting 1 30 3-Jaw Chuck 1 89 Baffle 1 31 Spindle 1 90 Tail Stock 1 32 Bearing (17 x 35 x 10) 2 91 Screw (M5 x 8) 1 33 Check Ring (#35) 2 92 Screw (M4 x 16) 2 34 Screw (M6 x 40) 3 93 Saddle Nut 1 35 Fixed Support 1 94 Lead Screw 1 36 Screw (M4 x 8) 2 95 Saddle Nut 1 37 Check Ring (#17) 1 96 Press Plate 1 38 V-Pulley 1 97 Small Washer (#4) 4 39 Adjust Ring 1 98 Screw (M4 x 10) 4 40 Washer 1 99 Nut Support 1 41 Head Stock 1 100 Bolt (M4 x 10) 4 42 Pulley Cover 1 101 Washer (#4) 2 43 Nut (M4) 6 102 Lead Screw Nut 1 44 Washer (#4) 4 103 Saddle 1 45 Screw (M4 x 8) 6 104 Screw (M6 x 20) 1 46 Hinge (38 x 31) 2 105 Saddle Wedge 1 47 Check Ring (#8) 2 106 Middle Saddle 1 48 V-Belt 1 107 Rest Nut 1 49 V-Pulley 1 108 Main Label 1 50 Spring Washer (#6) 4 109 Baffle 1 51 Screw (M5 x 20) 2 110 Screw (M5 x 10) 1 52 Small Washer (#5) 2 111 Protect Cover 1 53 Nut (M5) 2 112 Screw 1 54 Motor Connect Plate 1 113 Screw (M3 x 14) 1 55 Washer (#5) 3 114 Washer 1 56 Screw (M5 x 14) 3 115 Nut (M3) 2 57 Key (3 x 16) 1 116 Baffle 1 58 DC Motor 1 117 Screw (ST2.9 x 6.5) 2 58A Carbon Brush 2 118 Hex Wrench 1 set 59 Mat Plate 1 119 Screw Handles 3 120 Screwdriver 1 121 Fuse 1 SKU 95012 For technical questions, please call 1-800-444-3353 PAGE 19
ASSEMBLY DIAGRAM NOTE: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. 118: Hex Wrench Set not shown. 119: Screw Handles not shown. 120: Screwdriver not shown. 121: Fuse not shown. SKU 95012 For technical questions, please call 1-800-444-3353 PAGE 20
ELECTRICAL SCHEMATIC SKU 95012 For technical questions, please call 1-800-444-3353 PAGE 21
WARRANTY SKU 95012 For technical questions, please call 1-800-444-3353 PAGE 22