lamp post light Set up and Operating Instructions

Transcription

1 lamp post light Set up and Operating Instructions Distributed exclusively by Harbor Freight Tools Mission Oaks Blvd., Camarillo, CA Visit our website at: Read this material before using this product. Failure to do so can result in serious injury. Save this manual. Copyright 2008 by Harbor Freight Tools. All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing improvements, actual product may differ slightly from the product described herein. Tools required for assembly and service may not be included. For technical questions or replacement parts, please call

2 Save This Manual Keep this manual for the safety warnings and precautions, assembly, operating, inspection, maintenance and cleaning procedures. Write the product s serial number in the back of the manual near the assembly diagram (or month and year of purchase if product has no number). Keep this manual and the receipt in a safe and dry place for future reference. Important Safety Instructions In this manual, on the labeling, and all other information provided with this product: This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death. DANGER indicates a hazardous situation which, if not avoided, will result in death or serious injury. WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury. CAUTION, used with the safety alert symbol, indicates a hazardous situation which, if not avoided, could result in minor or moderate injury. NOTICE is used to address practices not related to personal injury. CAUTION, without the safety alert symbol, is used to address practices not related to personal injury. Read All Instructions General and Specific Safety Warnings 1. Wear ANSI-approved safety goggles during assembly and set-up. DO NOT replace old batteries with those of different types, charge levels, or capacities. It is important to always install new, fresh batteries identical to those included with this Lamp Post Light. 3. Keep the Solar Panel (1) clean. A dirty Solar Panel (1) will not allow sufficient sunlight to properly charge Batteries (5). 5. Warn children and others, that this Lamp Post Light is sturdy, but is not meant for overly hard wear. It should not have heavy weights leaned against it, or be used to swing around on. Maintain labels and nameplates on this Lamp Post Light. These carry important information. If unreadable or missing, contact Harbor Freight Tools for a replacement. SKU For technical questions, please call Page 2

3 6. Lighting Batteries These warnings, precautions and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this (or any) product, but must be supplied by the operator. Save these instructions. Specifications 12 LED (Sky Blue Color. Not Replaceable). Q ty 6, AA Ni-cd, 600mAh (Included, and Replaceable When Necessary). Unpacking When unpacking, check to make sure that the item is intact and undamaged. If any parts are missing or broken, please call Harbor Freight Tools at the number shown on the cover of this manual as soon as possible. Set Up Instructions Read the entire Important Safety Instructions section at the beginning of this manual including all text under subheadings therein before set up or use of this product. NOTE: For additional information regarding the parts listed in the following pages, refer to the Assembly Diagram on page 6 of this manual Assembly Before assembly, remove the Lamp Head Cover (2) and turn the Switch (22) to ON. This will allow the Batteries to charge and allow the Lamp Post Light to operate. Replace the Lamp Head Cover. This Lamp Post Light should be securely positioned for use in an area where it will receive constant sunlight. It should not be placed where trees or structures might block out the sun. This will assure maximum solar charging and longest light life at night. Replace the Battery Cover (4). Mount Lamp Base (17) to pre-drilled wood, or concrete sub base using 4 Expansion Bolts (18). NOTE: Expansion Bolts (18) should be driven into pre-drilled holes in concrete with a hammer. The threaded ends of the bolts will stick up through the holes in the Lamp Base (17) where a nut should be threaded onto each of them. Lead anchors can also be used by tapping them into predrilled holes, then use large hex-head screws through the holes in the Lamp Base (17) and into the anchors. Use the Screw (16) to fasten the Lower Support Shaft (15) to the Base. See Figure 1, below. Screw (16) Figure 1 SKU For technical questions, please call Page 3

4 Thread Lower Support Shaft (15) to Base (17). Thread Upper Support Shaft (14) to Lower Support Shaft (15). Thread Aluminum Lamp Frame (13) to Upper Support Shaft (14). See Figure 2 for steps 3 through 5. accidently (or purposely) turned off. Turn the Switch (22) back on so it will automatically turn on at dusk. WARNING! Do not dispose of old batteries in normal refuse. Dispose of old/ used batteries following all Local, State and Federal rules and regulations. NEVER INCINERATE BAT- TERIES. Operating Instructions Replacing Batteries Figure 2 Remove the Lamp Head Cover (2) by loosening Bolts (24) located on two sides of the Lamp Head Cover (2). Remove the Reflector (19) by loosening the Screw (7). Turn the Battery Housing (27) down from the Lamp Head Cover by loosening the Screw (21). Remove the Battery Cover (4) and remove the old batteries. Replace with 6 fresh new AA Ni-CD batteries. Always use a complete set of batteries. Do not replace partially. Always use the exact same type and size battery that come with the Lamp Post Light. Replace the Battery Cover (4), turn the Lamp Head Cover (2) over and replace on top of Lamp Post Light. Tighten both Bolts (24). NOTE: Check the Switch (22) after replacing Batteries (5). It may have been Read the entire Important Safety Information section at the beginning of this manual including all text under subheadings therein before set up or use of this product. Once mounted on secure platform, this Lamp Post Light operates automatically, or it may be turned on and off manually using Switch (22). Once it is turned on, It will operate automatically if you do not turn it back off. It will turn on at dusk and off sometime during the night, when the batteries have lost their charge. The Batteries will recharge during daylight hours and the Lamp Post Light will automatically turn on again at dusk. When first installed and used, the Lamp Post Light may not be as bright, or last as long as it should. It may take a couple of days for the Batteries (5) to fully charge. This is normal. WARNING: This Lamp Post Light is sturdy and functional. It will provide light for drive ways, walk ways and SKU For technical questions, please call Page 4

5 1. other areas that need extra light. It is not meant for hard wear. Do not lean against, or swing around on this Lamp Post Light. Warn children to be careful when playing near this Lamp Post light. Maintenance And Servicing Periodically, inspect general condition of Lamp Post Light. Check for loose screws, loose parts, and/or any other condition that may affect its safe operation. Periodically wipe down the Lamp Post Light with a clean rag slightly dampened with clear, fresh water. Troubleshooting Problem Possible Causes Likely Solutions Lamp Post Light does not come on at dusk. 1. Batteries may have worn out. Solar Panels are dirty. 3. Solar Panels possibly shaded by shrubbery growth. 1. Replace all batteries. Clean Solar Panels with soft rag slightly dampened with clean water. 3. Trim shrubbery. ON/OFF switch is in OFF position. Turn on switch. PART # DESCRIPTION Q'ty 1 Solar Panel & Circuit Board 1 2 Lamp Head Cover 1 3 Self Tapping Screw ST3X7 4 4 Battery Cover 1 5 Batteries AA Ni-CD 600 mah 6 6 LED 12 7 Screw M4X8 1 8 Glass Fasten Slice 12 9 Screw M5X Washer Glass Panel 6 13 Aluminum Lamp Frame 1 PARTS LIST 14 Upper Support Shaft 1 15 Lower Support Shaft 1 16 Screw M6X Lamp Base 1 18 Expansion Bolts 4 19 Reflector 2 20 Screw BT4X Screw M3X Switch 1 23 Thread Tube 3 24 Bolt M5X Nut M Connector Sleeve 1 27 Battery Housing 1 PLEASE READ THE FOLLOWING CAREFULLY The manufacturer and/or distributor has provided the parts list and assembly diagram in this manual as a reference tool only. Neither the manufacturer or distributor makes any representation or warranty of any kind to the buyer that he or she is qualified to make any repairs to the product, or that he or she is qualified to replace any parts of the product. In fact, the manufacturer and/or distributor expressly states that all repairs and parts replacements should be undertaken by certified and licensed technicians, and not by the buyer. The buyer assumes all risk and liability arising out of his or her repairs to the original product or replacement parts thereto, or arising out of his or her installation of replacement parts thereto. SKU For technical questions, please call Page 5

6 ASSEMBLY DIAGRAM ,9, Record Product s Serial Number Here: Note: If product has no serial number, record month and year of purchase instead. Note: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. SKU For technical questions, please call Page 6