Bluetooth v.0, v. RS Serial Adapter - SMA Connector Revised /DEC/0 mm mm mm Features Bluetooth v.0, v. wireless technology dbm Tx Power and - dbm Rx Sensitivity Serial (RS) interface Serial Port Profile (SPP) available Programmable Standalone Module (With Embedded Bluetooth v.0, v. Stack) Unique patented firmware enabling serial printer functionality Up to 000m (in open space) with an alternative antenna and up to 00m (in open space) with standard dbi antenna. Full Duplex for simultaneous communication between sender and receiver Ease of configuration and setup using the LM9 software Configurations pre-installed on production RoHS, REACH and WEEE Compliant Solution Typical Industries EPOS mm x mm x mm (without SMA Connector) Aviation Powered by USB - Mini USB, DB9 or AC adaptor MM DTE / DCE (Master / Slave) mode switch Automotive DTR / DSR Handshaking and RTS / CTS Flow control lines LNG Overview The Bluetooth serial adapter (RS) provides a secure and reliable Bluetooth v.0, v. connection. This wireless connection reaches a range of up to 00m in open space with a standard antenna ( dbi) and a range of up to 000m in open space by using an altenative antenna (See LM ( dbi), LM ( dbi), LM (9 dbi)), replacing the RS cables between a master (DTE) device and slave (DCE) device(s) such as printers, data loggers and digital signalling devices. The patented firmware allows the serial configurations to be used. The firmware controls the RS signals, including DTR / DSR handshaking and RTS / CTS flow control lines. The is powered by USB, DB9 or AC adaptor. All settings and configurations are even retained when the adapter is powered down. Our LM9 software can be used to change the settings and configurations, including auto connect function, discoverable / non-discoverable function, device name, baud rate, data bits and flow control. AT Commands are used to change the configurations. The developer is also able to configure and modify the settings of a remote from a local. Customised configurations and settings can be preloaded to the, simplifying the manufacturing and testing process. Page of
Bluetooth v.0, v. RS Serial Adapter - SMA Connector General Specification Wireless Bluetooth Standard v.0 and v. Adapter Type Standalone (Configurable with AT Commands) Profiles SPP Hardware Chipset CSR Antenna SMA Connector Flash Memory Mbit RAM KB Interfaces Serial (RS) Power Supply V to V DC Crystal Oscillator MHz LED Indicators Link (BLUE), Data (ORANGE) and Power (RED) RS (Serial) RS Interface D_SUB 9 pin female Signal RxD, TxD, DTR, DSR, RTS, CTS and GND Full Duplex Yes Baud Rate.,.,., 9., 9.,.,.,., 0., 0. and 9. Kbps RF Characteristics Tx Power dbm (Maximum) Rx Sensitivity - dbm (Typical) Antenna Gain dbi (Typical) Current Consumption 0 ma (Maximum) Range (in open space) Up to 000m with an alternative antenna. Up to 00m with Standard dbi antenna Data Rate Up to Mbps Frequency. GHz to. GHz Hopping,00/sec, MHz channel space Modulation Scheme GFSK-Mbps, DQPSK- Mbps, and -DPSK-Mbps Physical Characteristics Operating Temperature -0 C to + C Dimensions (L x W x H) mm x mm x mm (without SMA Connector) Weight. g Compliance RoHS, REACH and WEEE Page of
Bluetooth v.0, v. RS Serial Adapter - SMA Connector Signals Female DB9 9 Pin outs for Adapter Pin RS Signal DTE to DCE Direction DCE to DTE Direction Description CD Not Connected RxD Receive Data TxD Transmit Data DTR Data Terminal Ready GND n/a n/a Signal Ground DSR Data Set Ready RTS Request to Send CTS Clear to Send 9 Vcc Power Supply Factory Settings The factory settings of the COM Port are as follows: Baud Rate Data Bits Parity Stop Bits Flow Control 900 bps None None Customised settings are available as factory settings upon special request; Bonding, Pre-Pairing, different Baud Rates, Data Bits, Parity and Flow Control Settings. Page of
Bluetooth v.0, v. RS Serial Adapter - SMA Connector Hardware Structure Link LED. Data LED. Power LED. RS Connector. Slide Switch. Mini USB Connector. Reset Button. Antenna Connector. Switch Functions Reset Button By pressing the Reset Button you can: Disconnect a wireless connection (after a short press). Restore the factory settings (after over seconds press). Slide Switch The slide witch can swap TxD/RxD, RTS/CTS signals. By switching, you can set the adapter as a DTE (towards antenna connector) or a DCE (towards RS connector). Additional Dimensions mm mm mm CFG mm Page of
Bluetooth v.0, v. RS Serial Adapter - SMA Connector See Below Packaging Options 0-000 AO - Adapter Only x Bluetooth Serial Adapter x dbi Antenna 0-00 SRP - Single Retail Pack x Bluetooth Serial Adapter x dbi Antenna x DB9 male to female connector x USB - mini USB Cable for power supply x All in one power supply (UK, EU and USA) Optional LM0 Slim Line 9 pin to pin Convertor 0-009 0-00 Twin Pack Pre-Paired x Bluetooth Serial Adapter TRP - Twin Retail Pack x Bluetooth Serial Adapters. x dbi Antenna s. x DB9 male to female connector. x USB mini USB Cable for power supply. x All in one power supply (UK, EU and US). Optional LM0 Slim Line 9 pin to pin Convertor See our website to download any applicable Software, Manuals and Notes - http://www.lm-technologies.com/downloads Page of