Note: Over-reinforced typically means the tensile steel does not yield at failure. for this example, over-reinforced means the section is not tension controlled per ACI standards even though the steel does yield Given: f c = 6,000 psi fy = 60 ksi Required: Determine the nominal moment capacity, ΦMn Assumptions: 1. Plain sections remain plain (ACI 318-08 section 10.2.2) 2. Maximum concrete strain at extreme compression fiber = 0.003 (ACI section 10.2.3) 3. Tensile strength of concrete is neglected (10.2.5) 4. Compression steel is neglected in this calculation.
Let s start by constructing the stress and strain diagrams: Next, we ll calculate d, the depth from the extreme compression fiber to the center of reinforcement in the tensile zone. d = h Clear Spacing dstirrup dreinforcement - Clear Spacing Between Bars/2 d = 24 1.5 0.5-1 - 1 /2 d = 20.5
Next, we want to use equilibrium to solve for a, the depth of the Whitney stress block From the rules of equilibrium we know that C must equal T C = T C = 0.85 x f c x b x a Defined in ACI section 10.2.7.1 b = width of compression zone a = depth of Whitney stress block C = 0.85 x 6000psi x 12 x a = 61,200 lb/in x a T = fs x As fs = stress in the steel (we make the assumption that the steel yields, and will later confirm if it does). As = area of tensile steel T = 60000psi x (8 x 0.79 in 2 ) = 379,200 lb
Solve for a: 61,200 lb/in x a = 379,200 lb a = 6.196 Now that we know the depth of the stress block, we can calculate c, the depth to the neutral axis. From ACI 318 section 10.2.7.1 a = β1 x c β1 is a factor that relates the depth of the Whitney stress block to the depth of the neutral axis based on the concrete strength. It is defined in 10.2.7.3 β1 = 0.65 0.85 - ((f c 4000psi)/1000)) x 0.05 0.85 β1 = 0.85 ((6000psi 4000psi)/1000) x 0.05 = 0.75 c = a / β1 = 6.196 /0.75 c = 8.261 With c, we can calculate the strain in the extreme tensile steel using similar triangles. With this strain calculated, we can check our assumption that the steel yields, and determine if the section is tension controlled. First, let s calculate dt, the depth from the extreme compression fiber to the extreme tensile steel dt = 24-1.5-0.5-1 /2 = 21.5 c/ε c = dt/(ε c + ε t ) ε t = (dt x ε c )/c ε c = (21.5 x 0.003)/8.261 0.003 ε t = 0.0048
Determine if the section is tension controlled: Determine if the section is tension controlled: Per ACI section 10.3.4 a beam is considered tension controlled if the strain in the extreme tension steel is greater than 0.005. The calculated steel strain in our section is 0.0048 which is less than 0.005 therefore this beam section is not tension controlled. Per ACI section 10.3.5 εt at nominal strength for flexural members shall not be less than 0.004 (0.0048 is acceptable) The strain for our section is between the limit for compression controlled (.002 per ACI section 10.3.3) and the limit for tensioned controlled sections, 0.005. Therefore, we must interpolate to determine our Φ factor in accordance with ACI 9.3.2.2 (0.9-0.65)/(0.005-0.002) = (Φ - 0.65)/(0.0048-0.002) Φ = 0.88 Determine the strain at which the steel yields and check our assumption that the steel in fact yielded: E = f y /ε y E = Young s modulus which is generally accepted to be 29,000 ksi for steel f y = steel yield stress ε y = yield strain ε y = 60ksi / 29,000 ksi = 0.00207
When we checked if the section was tensioned controlled, we check the strain at the extreme layer of steel. We must calculate the strain at the centroid of the tensile steel to determine if it yields: ε s = (d x ε c )/c ε c = (20.5 x 0.003)/8.261 0.003 ε t = 0.0044 0.0044 is greater than 0.00207 therefore our assumptions are correct and the steel yields prior to failure Next, let s determine if the beam section satisfies the minimum steel requirements of ACI: Per ACI section 10.5.1, the minimum steel requirement is: A s, min = ((3 x square root(f c))/f y ) x b w x d (200/fy) x b w x d As a side note, the 200/f y minimum controls when f c is less than 4,500 psi A s, min = ((3 x squareroot(6,000 psi))/60,000psi) x 12 x 20.5 A s,min = 0.95 in 2 A s = 8 x 0.79 in 2 = 6.32 in 2 > 0.95 in 2 therefore we satisfy the minimum steel requirements of ACI
Finally, let s calculate the nominal moment capacity of the section: Using moment equilibrium, we can calculate the moment capacity by taking the moment about the center of the tensile force, or the center of the compressive force. Calculate the moment about the center of the compressive force: ΦM n = Φ x T x (d a/2) Φ = 0.88 as we previously calculated T = A s f y ΦM n = 0.88 x 6.32 in 2 x 60 ksi (20.5in - 6.196in / 2) ΦM n = 5,807 kip*in = 483.9 kip*ft
For questions or comments, send me an email at info@civilpe.net Check us out on the web at http://www.civilpe.net