Technical Specification for 5VDC/2A +12VDC/2A Adapter Contents 1. SCOPE This specification defines the performance characteristics of a grounder,single phase, 34 Watt,2 outputs power supply.this specification also defines worldwide safety and electromagnetic compatibility requirements for the power supply which is intended for use move disk products. 2.INPUT REQUIREMENTS 2.1.1NPUT VOLTAGE Range Minimum Maximum Nominal Low 100 Vac 132 Vac 110-120 Vac High 180 Vac 264 Vac 200-240 Vac 2.2.FREQUENCY Range Minimum Maximum Nominal Single 47 Hz 63 Hz 50/60 Hz 2.3. VOLTAGE SELECTION A full range will be provided to select the appropriate range. 2.4.INPRU CURRENT 1.5 amps maximum at input voltage within the low range as specified in paragraph 2.1and at any combination of loading conditions. 1.0 amps maximum at input voltage within the high range as specified in paragraph2.1 and at any combination of loading conditions.
2.5. INRUSH CURRENT The adapter inrush current shall be less than the ratings of its crltical components(including bulk rectifiers,fuses,and surge limlting device)for all conditions of line voltage of Section2.1. 2.6The power supply efficiency shall not be less than 75%measure at the maximum load as specified in paragraph 3.1with the AC input set at the nominal voltage.
3.OUTPUT REQUIREMENTS 3.1.STATIC DC LOAD Nominal voltage(vdc) Load current(a) Output deviation (V) Output 12v Output 5v 12.0/5.0V 2A 2.0A 12.0±5%,5.0±5% 3.2. RIPPLE AND NOISE The ripple and noise of the outputs shall be measured at the load end of the output cables when terminated to a load impedance as specified in paragraph3.3 Output Ripple&noise(P-P) Use 20M Hz bandwidth frequency scope 12.0/5.0 Vdc 100 mv 3.3. LOAD IMPEDANCE Filter capacitors are connected to each pins of the mating output connector.capacltance vaues and material type are listed below. Voltage Nom.(V dc) Capacitance Nom(µF) Material type 12.0/5.0 10/0.1 TAN\MON 3.4.HOLD UP TIME The power supply shall maintain voltage regulation within the specified limits in paragraph 3.1for at least20 milliseconds after lose of input voltage measure at 100Vac and at maximum output load. 4.NO LOAD OPERATION The power supply shall be able to operate under no lode condition,no damage to the power supply is allowed and internal component can not be stressed beyond its rating. 5.FREQUENCY OF OPERATION To keep andible noise to a minimum,power supply shall be switched at frequencies higher than 20KHz. 6.TEMPERATURE COEFFICIENT The temperature coefficient of all outputs are 1%per degree centigrade maximum. 7.PROTECTION 7.1SHORT CIRCUIT PROTECTION A short circuit place on DC output shall cause no damage to or shutting down the power supply, The power supply will recover automatically after removal of the short circult fault.power on reset is not required. 7.2.Load condition The power supply can operate mobil HDD from 80G to700g under voltage,100-240v AC/input and it can
also work together with three HUB under voltage 110-240v AC/input. 8.TURN ON TIME The turn on time shall be less than 10 sec for all line and conditions.(measured from Ac on point to the 90%point of the output voltage) 9.SAFETY REQUIREMENTS The power supply must comply with the following national standards: 〇 United states&canadian standard:(file No:E257074) UL/CUL:EN60950 〇 CCC standard: (File No:2005010807154974) EN60950 9.1.DIELECTRIC STRANGTH Primary to secondary: Primary to secondary 1500Vdc for 1min,Cutoff current shall be less than 10MA,Test time 1 sec in production line. Secondary to case 1500Vdc for 1 min,cutoff current shall be less than 10MA. Test time 1sec in production line. 9.2INSULATION RESISTANCE Primary to secondary:30 Meg.ohms Min,500Vdc. 9.3GROUND LEAKAGE CURRENT The power supply ground leakage current shall be less than 500µA at 240Vac/60Hz condition
10.ELECTROMAGNETIC COMPATIBILITY Power supply for use with the host systerm will be tested to conform with the following emission standards. 10.1.CE Mark / FCC Mark LVD : EN60950 EMC :EN55022/A1:2000 10.2.LIGHTNING SURGE AND EFT/BURST The power supply shall meet 1.5KV(1.2/50uS) requirement at normal & common mode condition. The EFT/BURST specification shall meet IEC 801-4 class 3. 10.3.ESD The power supply shall meet contact discharge 6KV and air discharge 10KV requirement,when power Supply is operating at maximum load conaition. 10.4.TEMPERATURE RISE The maximum temperature rise(delta t) measured at any point on the enclosure surface shall not exceed 60degrees c in closed carton chamber and no air flow. 11.VIBRATION AND SHOCK The power supply unit shall withstand forces of 0.5G at variable recurrent frequencies of 10 to 500Hz and a simulated transportation test.transportation test will consist of a 1/2G vibration force at the resonant frequencies of the board or components.the test will last for 15 min.the unit will be tested in a configuration representative of the intended application with shipping cartons,the unit must survive a 1G force for a duration of 10 ms in all 3 orthogonal plans from normal mounting point. 12.DROP The power supply unit shall successfully comply with the following drop test requirement: 6 random drops from a height of 100cm into concrete covered with 1/8 inch asphalt tile or similar NO.impairment of normal function,breaking away of any parts or change that would render power supply unit potentially harmful shall occur.
13.RELIABILITY 13.1MEAN TIME BEFORE FAILURE(MTBF) The MTBF for the power supply unit shall equal or exceed 10,000hours when operated at full rated load in an amblent temperature of 25 degree. 13.2.ON-OFF LIFE To verify the power supply withstand 1,000 time on-off repetition of primary power without failure or damage at 100V ac input. 13.3.BURN-IN 100%burn-in test at 80-100% of full/rated load at 35-40burn-in room,72hrs test for prototype samples,24hrs test for pilot run samples for,4hrs test for mass production 14.ENVIRONMENT 14.1.OPERATING Temperature: 25 degrees centigrade. Relative Humidity:30 to 85 percent,non-condensing. 14.2. SHIPPING AND STORAGE Temperature: 0 to +75 degrees centigrade. Relative Humidity: 0 to 95 percent,non-condensing. 15.NET WEIGHT:250gs 16.PRODUCTION FACTORY C.SA ELECTRICAL FACTORY 17.PRODUCTION COUNTRY CHINA