RHINO PSM Series Supplies Our versatile switching power supplies are DIN-rail mountable Features Industrial grade design Sturdy metal case to withstand harsh industrial environments Model PSM4-090S-N meets NEC Class Universal 00/30 VAC input voltage Adjustable output voltage Low output ripple Short-circuit, overvoltage and overtemperature protection Good signal Optional wall mounting Specialty modules for redundancy, power backup and UPS Terminal connectors included 3-year product warranty Control output for true N+ redundancy or battery operation Multiple output terminals for easy wiring Dual color status indicator LED Adjustable output voltage DC-OK monitoring via relay contact and NPN output Universal input voltage for worldwide use Jumper for parallel operation or battery charge mode selectable by jumper Rugged, ultracompact metal case, shock and vibration to IEC 68- Industrial approvals: CSA IEC/EN 60950 Convection cooling, no internal fan, thermal overload protection Full CE compliance including EN6000-3- Self-locking DIN-rail fixing latch Part Numbering System PSM 4 090S-N NEC Class Screw Terminal Connector Watts Volts Series Name: PSM = metal case RHINO PSM Industrial Supplies Part Number * Voltage (V nom ) ** Current (I max ) *** (P max ) PSM-078S VDC 6.5 A 78 W PSM4-090S 4 VDC 3.75 A 90 W PSM4-090S-N 4 VDC 3.75 A 90 W PSM-56S VDC 3.0 A 56 W PSM4-80S 4 VDC 7.5 A 80 W PSM4-360S 4 VDC 5.0 A 360 W PSM4-600S 4 VDC A 600 W *V models adjustable from to4 VDC. 4V models adjustable from 4-8 VDC **Maximum current at nominal output voltage ***Up to an operating temperature of +40 C 6 4 Products -800-633-0405
RHINO PSM Series Supplies Specifications Input Specifications Part Number Input Voltage Range Input Input Current Inrush Current max Frequency (Typical) at full load (<ms) @ +5 C Holdup Time Efficiency (Typical) Circuit Breaker or Range @ 5VAC Fuse (slo-blo) 5 VAC 30 VAC 5 VAC 30 VAC PSM-078S.0 A.0 A 8% 00-40 VAC PSM4-090S 85-64 VAC. A.0 A < A <0 A 85% (47-63 Hz) PSM4-090S-N. A.0 A 85% 6.0 A to 6.0 A 0 ms min. PSM-56S 00-0 VAC/ 47-63 Hz.5 A.4 A (full load 85% 0-30 VAC <3 A <5 A 5/30 VAC) PSM4-80S 85-3 VAC/.8 A.5 A 88% 87-64 VAC PSM4-360S 5.0 A.5 A <6 A <5 A 87% 0.0 A to 6.0 A (47-63 Hz) PSM4-600S Autoselect 0.0 A 5.0 A <5 A <30 A 89% 6.0 A to A Part Number Specification Temperature Humidity Isolation Regulation Voltage Ripple Protection Overtemperature Protection Status Indicator Maximum Capacitive Load Vibration Shock Description General Specifications Operating (ambient): -5 C to + 70 C max (-3 F to 58 F). Above +40 C(04 F) load derating Storage (non-operating): -5 C to + 85 C max (-3 F to 85 F). Temperature drift: 0.0%/C. Cooling: convection, no internal fan 95% (non-condensing) relative humidity maximum According to IEC/EN 60950, EN5078, EN6558--8, EN6004, CSA Input variation: 0.5% maximum. Load variation (0 to 00%): 0.5% maximum 00 mv peak-to-peak typical (0 MHz bandwidth), (00 mv peak - peak maximum at Imax) Current limit: 0% constant current, automatic recovery, thermal protection, output rating, Voltage limit: 40% Vout nom Switch off at overtemperature, automatic restart Dual color LED (green: DC Ok; Red: DC Off) By external contact. DC On: -S contact open. DC Off: -S connected via K to -Vout Unlimited IEC 60068--6: 3 axis, sine sweep, 0-55 Hz, g, oct/min IEC 60068--7: 3 axis, 5g half sine, ms Enclosure Rating IP0 (IEC 59) Enclosure Material Aluminum (chassis) / zinc plated steel (cover) Mounting Snap-on with self-locking spring for 35mm DIN rails per EN 500-35x5/75, or wall mount with bracket Connection Agency Approvals Price Voltage Voltage Adj. Current Range (Max.) (Max.) Specifications Overvoltage Protection Pluggable screw terminals (plugs included) terminals per output (not available in 600 watt unit.) CE/CSA C No. 60950--03, CSA to UL STD. 60950-, pending UL - Good Signal Trigger Active Threshold Signal PSM-078S <---> VDC - 4 VDC 6.5 A 78 watts 0 V 9 - V V ± V/0 ma max. PSM4-090S <---> 3.75 A 90 watts 35 V 4 VDC 4-8 VDC 8 - V V ± V/0 ma max PSM4-090S-N <---> 3.75 A 90 watts 35 V PSM-56S <---> VDC - 4 VDC 3.0 A 56 watts 0 V 9 - V V ± V/40 ma max. PSM4-80S <---> 7.5 A 80 watts 35 V PSM4-360S <---> 4 VDC 4-8 VDC 5.0 A 360 watts 35 V PSM4-600S <---> A 600 watts 35 V 8 - V V ± V/0 ma max Note: Unless otherwise stated all specifications are valid at nominal input voltage, full load and +5 C after warmup time. MTBF (IEC 6709 @ 5 C) Relay DC OK = contact closed (rated:30 VDC.0A) 350,000 hours Overview DL05/06 DL05 DL05 DL305 DL405 Field I/O Software C-more HMIs Other HMI AC Drives Motors Steppers/ Servos Motor Controls Proximity Photo Limit Switches Encoders Pushbuttons/ Lights Process Relays/ Timers Comm. TB s & Wiring Enclosures Appendix Part Index www.automationdirect.com/powerandaccessories Products 6 5
RHINO PSM Series Supplies Specifications General Specifications (continued) Specification Standard Document Number Harmonic Limits Harmonic Current Limits EN 6000-3-, Class A for limited output power Information technology equipment Industrial control equipment IEC/EN60950 CSA Safety Standards Electrical equipment of machines EN 6004 Electronic equipment for power installation EN 5078 Safety, transformers EN 6558--8 Limited power source (model PSM4-090S-N) EN 60950 sect..5 and NEC Class Safety Approvals CB-Report per IEC 60950 EN 5078, EN 60079-5 EN 6558--8, CSA Safety Class Degree of electrical protection Class IEC 536 Electromagnetic Compatibility (EMC), Emissions Electromagnetic Compatibility (EMC), Immunity EMC, Emissions Conducted RI suppression on input Radiated RI suppression EN 604-3, EN6000-6-3 EN 550 class B, EN 550 class B EN 550 class B, EN 550 class B EMC, Immunity EN 6000-6-, EN 604-3 Electrostatic Discharge (ESD) Radiated RF field immunity (80-000 MHz) Electrical fast transient / burst immunity Surge immunity IEC / EN 6000-4- 4 kv (contact discharge) / 8 kv (air discharge) IEC / EN 6000-4-3 0 V / m IEC / EN 6000-4-4 kv IEC / EN 6000-4-5 kv / kv Immunity to conducted RF disturbances (0.5 to 80 MHz) IEC / EN 6000-4-6 0 V frequency field immunity IEC / EN 6000-4-8 30 A / m Voltage dips IEC / EN 6000-4-(70% UN Crit. B/40%/00% UN Crit. C) Pollution Degree * *Note: Normally, only non-conductive pollution occurs. Temporary conductivity caused by condensation is to be expected. Derating A) Derating vs Ambient Temperature B) Derating vs Input Voltage 00 00 [% Pmax] 90 80 70 60 50 40 30 0 0 0-5 40 50 60 70 Temperature [ C] PSM 600 PSM 078 PSM 56 PSM 090 PSM 80 PSM 360 Note: Unless otherwise stated, all specifications are valid at nominal input voltage, full load and +5 C after warmup time. [%Pmax] 90 80 70 60 50 40 30 0 0 0 85 90 00 0 5 3 87 30 64 Input Voltage [VAC] 6 6 Products -800-633-0405
Remote P S P/S P/S P S Remote RHINO PSM Series Dimensions/Connections Overview PSM-078S, PSM4-090S, PSM4-REM360S, PSM4-BCM360S PSM-56S, PSM4-80S, PSM4-BFM600S DL05/06 DL05 DL05 DL305 DL405 Field I/O PSM4-360S PSM4-360S (4.9) 80.0 (3.5) DC ON O/P ADJ. DC OK Pin Earth GND (-) S+ Normal mode Pin Neutral Vout (+) S- Common Pin 3 Line DC-OK Signal Parallel mode Pin 4 contact Pin 5 contact 45.0(.77) 86.5(3.4) (4.9) PSM4-600S Pin Earth GND (-) S+ Normal mode Pin Neutral GND (-) S- Common Pin 3 Line Vout (+) Parallel mode Pin 4 Vout (+) Pin 5 DC-OK Signal Pin 6 contact Pin 7 contact 86.5(3.4) 45.0(.77) (4.9) Software C-more HMIs Other HMI AC Drives Motors Steppers/ Servos Motor Controls Proximity Photo Limit Switches Encoders Pushbuttons/ Lights PE N L Process 5.0 ( 0. 0 ) 46.0 7.0 (.8) (0.67) Pin Earth GND (-) S+ Normal mode Pin Neutral GND (-) S- Common Pin 3 Line Vout (+) Parallel mode Pin 4 Vout (+) Pin 5 DC-OK Signal Pin 6 contact Pin 7 Weight:.kg contact (.4 lb) (4.9) PE N L 05.0 (4.3) 65.0 (6.50) DC OK J5 30.0 (.8) DC ON O/P ADJ. J5 Pin Earth GND (-) S+ Normal mode contact Pin Neutral GND (-) S- Common contact Pin 3 Line Vout (+) Parallel DC-OK Signal mode Pin 4 Vout (+) Weight:.8kg (6.0 lb) Relays/ Timers Comm. TB s & Wiring Enclosures Appendix Part Index All dimensions in millimeters (inches) Tolerances: ±0.5mm (±0.0 ) www.automationdirect.com/powerandaccessories Products 6 7
RHINO PSM4-REM360S Redundancy Module Using two PSM4 power supplies and a redundancy module, you can configure a redundant power system, featuring active current sharing, without any additional components. Even if one power supply fails or becomes disconnected, the second unit will supply full current to the load. The module has an alarm contact for monitoring of operations. The inputs are hotswappable and can be loaded up to 5A each. Redundancy Module Part Number Price Input Max per Input Voltage Adjust Max PSM4-REM360S (includes terminal plugs) <---> x 4 VDC x Control Input x 360 W 4 VDC (4-7 VDC) 360 W Operating Temperature Electromagnetic Compatibility Redundancy OK Signal Dimensions Remote Link Wire 0.5m Alarm Contact Rating Redundancy Module Function Diagram General Specifications -5 C to +70 C max (-3 F to +58 F), derating above 40 C (04 F) In correspondence to connected units (no internal switching device) Trigger threshold at 8 to VDC. Contact closed if one or both inputs failed Same as model PSM4-090S (see dimensions page) Two cables included with PSM4-REM360S module By external contact: ON = J5.3 + J5.4 not shorted OFF = J5.3 + J5.4 shorted 30 VDC/.0 A max Redundancy Module Connector Positions Front view Bottom view Top view 3 4 - - + + PSM.....3.4.. Remote Link Remote Link.4.3 PSM.. DC IN DC IN J5 3 4 - + - + J5. J5. J5.3 J5.4 Note: this redundancy module only works with the PSM series. Other series of power supplies are not compatible. 3 4 Voltage control Voltage control J5 for Input for Input Pin Input -Vin GND (-) S+ S+ DC-OK Signal Pin Input +Vin GND (-) S- S- contact Pin 3 Input -Vin Vout (+) Pin 4 Input +Vin Vout (+) 6 8 Products -800-633-0405