WE HAVE THE RIGHT POWER SUPPLY FOR YOUR APPLICATION

Transcription

1 WE HAVE THE RIGHT POWER SUPPLY FOR YOUR APPLICATION P L U S C O M P L E T E P E A C E O F M I N D W I T H H I G H E S T Q U A L I T Y & P R OVEN R E L I A B I L I T Y Switchmode Supplies Australia Core Assortment Catalogue & Price List 2010/2011

2 Supply Selection Considerations All Weidmuller Switchmode Supplies have a regulated output voltage, that is the output voltage remains constant irrespective of input voltage or load current, provided the supply voltage is within the specified range. Some models can be powered from DC as well as AC Environmental Environmental issues to consider are the ambient temperature where the power supply is expected to operate. Note the de-rating for high ambient temperature use. Vibration in the area of use must also be considered. Boost All Weidmuller Switchmode Supplies have start up boost of up to 400%. This allows for non resistive loads to be started. Inductive loads, i.e. solenoid valves and motors, have a starting current as high as six times full load current, while capacitive loads, i.e. some electronic devices and PLC s with input filtering capacitors have a start up current of up to twelve times. Switchmode power supplies have a built in protection circuit which turns the output off if a sudden load is introduced which exceeds the rated load of the power supply. Overload Protection Overload thermal protection is built in to protect the power supply if the load applied is in excess of the rated current, for a period of time. This will shutdown the output until the power supply cools down, and will need to be reset by disconnecting and reconnecting the input supply. Short Ciruit Protection Short circuit protection is also built in so that if there is a short circuit in the load circuit the power supply will shutdown until the short circuit is removed, and will auto start. Mounting Mounting types available are DIN rail mounting or chassis / panel mounting. Redundancy For redundant operation where two identical power supplies are connected in parallel, for reliability and safety reasons the use of diode auctioneering modules is necessary. In this configuration there is no possibility of a back feed from one power supply to the other and supply failure alarms can be operated. Load Sharing When two or more power supplies are to be connected in parallel for power sharing the output voltage of the power supplies must be adjusted to be within 50mV of each other. To achieve this the voltmeter being used must be accurate and all test leads must be securely connected when making the adjustment, not just held or pushed onto the terminals. The method of wiring must also be done in the correct configuration so as to avoid different wire lengths when bridging the power supplies. If possible the use of a single higher output power supply is a better option than parallel connect smaller power supplies. It is often difficult to get more than two parallel connected power supplies to current share. Method of operation Primary switch-mode power supplies are distinguished by a high degree of efficiency and also by their compact dimensions and moderate generation of heat. The mains voltage is rectified directly. The rectified voltage is then chopped with a higher frequency than that of the mains frequency. A transformer which can be quite small due to the high switching frequency converts the voltage with the switching frequency to the required value. The voltage is now rectified and smoothed by a filter. This regulator control itself is carried out by means of pulse-width modulation. The on and off times of the chopper transformers are regulated to ensure that the output voltage remains stable. 2

3 CONTENTS Supplies ECOLine The price vs performance winner. PRO-M Advanced feature power supply in ultra compact housing. PRO-H For industrial and critical power requirements. INSTA 25-48W Versatile adjustable output voltages from 4 to 55Vdc. INSTA 24W ing inductive loads. Up to 3 times starting current. WAVE Slimline fully protected power supply with plug / socket connections. EasyLine Panel mount stable and reliable power for machines. QUICK SELECTION GUIDE Supply Model AC DC DC Adjustable Boost at start up Stackable Housing ECOline / to 20 50% for 2-5s Y Metal ECOline 3 Phase X to 40 50% for 2-5s Y Metal PRO-M to % for 2min with space PRO-M 3 Phase to % for 2min with space PRO-H / N/A to 25 N/A Y Metal Metal Metal INSTA 25-48W INSTA 24W to 55 Y 1 to 5 N/A Y Plastic to 28 N 1 to 2 400% Y Plastic EasyLine , 24, 48 Y 1.1 to % N/A Metal 3

4 ECOLINE Efficient and Reliable DC Switchmode Supplies Ventilation Ventilation Channel for Side by Side stacking with no derating Indication LED Indication Robust Robust metal housing mounts on TS35 DIN Rail AC / DC International use Thanks to the wide range of inputs (85 V AC to 265 V AC), the power supplies range is suitable for a wide variety of applications. Local and International Approvals: C Tick, CE, UL, CSA 4 All prices exclude GST. Weidmuller standard terms & conditions of sale also apply.

5 ECOLINE 1 & 3 Phase W MAXIMUM PERFORMANCE vs PRICE If you're comparing price with performance, the economical ECOLINE series is the flagship of Weidmuller's range of switchmode power supplies. Packed with features and with the same quality and reliability you've come to expect from Weidmuller, the ECOLINE will not disappoint. Robust metal housing Mounts on TS35 Din Rail LED power indication Adjustable output 24-28Vdc for Drop Compensation Wide range switchable supply input voltage Built-in remote status alarm via C/O relay diode module for parallel connection/redundancy Built-in ventilation channel for side by side stacking & no de-rating Up to 50% overload protection and auto restart ( boost 2-5s) Local and International Approvals: CTick, CE, UL, CSA Max. List Price 1-phase 72W 3 A Vdc Vac/ Vdc 110 x 55.5 x $ W 5 A Vdc Vac/ Vac/ Vdc 110 x 65.5 x $ W 10 A Vdc Vac/ Vac/ Vdc 110 x x $ W 20 A Vdc Vac/ Vac/ Vdc 110 x x $ phase 250W 10 A Vdc 3x400Vac/ Vac 110 x x $ W 20 A Vdc 3x400Vac/ Vac 110 x x $ W 40 A Vdc 3x400Vac/ Vac 125 x 280 x $ ECOLINE Diode Modules DOUBLE YOUR POWER / REDUNDANCY 240V~ ECOLINE Supplies 240V~ 24V E1 E2 V V Diode Module DC + - It is often necessary to connect two power supplies in parallel for increased load current requirements or redundancy. The best solution to do this is to use a Diode Auctioneering Module. These modules contain two full current rated diodes with a common cathode connection. To install you simply connect the output of each power supply to the input terminals of the diode module. A single output is then available from the diode module. With this setup the power supplies can not drive each others output. Robust metal housing 24V - Mounts on TS35 Din Rail Built-in ventilation channel for side by side stacking & no De-rating Local and International Approvals: C Tick, CE, UL, CSA Type List Price CP DM A max or 10A redundancy mode Vin-0.5 typical 40Vdc max. 2 x 0-10A max. 125x55.5x $78.04 CP DM A max or 20A redundancy mode Vin-0.5 typical 40Vdc max. 2 x 0-20A max. 142x55.5x $ All prices exclude GST. Weidmuller standard terms & conditions of sale also apply. 5

6 from 33 mm PRO-M supplies for space-saving use in automation technology Narrow Space-saving configuration in the switching cabinet through very narrow housing construction and side-by-side connectability. 25 C to +70 C Robust Wide temperature range from 25 C +70 C. Parallel connection Module power can be increased by connecting up to five power supplies in parallel without diode module. AC / DC International use Thanks to wide-range input (both DC as well as AC voltages can be used; no switching required) and extensive approvals (UL/CSA and GL (EMC 1 - bridge). 6 All prices exclude GST. Weidmuller standard terms & conditions of sale also apply.

7 PRO-M PRO-M Advanced Feature Switchmode Supplies The new PRO-M range of switchmode power supplies have a space saving of up to 50% and no gap required between multiple units. PRO-M will squeeze into the tightest of switchboards or machines Extended temperature Range of -25 C to +70 C extends the number of application possibilities increasing with up to 5 modules is accomplished without the need for external diode modules Small in Size, Big on Performance The optimal and reliable power supply for machinery. The solid, very narrow metal housing of the 10 different versions of the 24 V DC supply enable installation without lateral spacing, thereby saving space on the DIN rail. AC and DC wide-range inputs and a broad temperature range enable universal use. Thanks to its high efficiency, over load resistance and high performance reserves, the PRO-M is the reliable power supply in all applications. Should one phase fail, the 3-phase PRO-M power supply modules continue to work reliably, i.e. in two-phase operation. A boost up to 120% is provided for up to 2 minutes and with overall efficiencies of up to 90% the new PRO-M series delivers in all areas ful Wide choice Rated load 120 % 100 % reserve 45 C 60 C 70 C Temperature With additional power reserves at standard temperatures. The right power supply for every application: 1-phase 3 A, 5 A, 7.5 A, 10 A, 20 A, 40 A and 3-phase 5 A, 10 A, 20 A, 40 A. Max. 1-phase No. List Price 70 W 3A 24 V (22.5 to 29.5 V) Vac / Vdc 125x33x $ W 5 A 24 V (22.5 to 29.5 V) Vac / Vdc 125x40x $ W 7.5 A 24 V (22.5 to 29.5 V) Vac / Vdc 125x50x $ W 10 A 24 V (22.5 to 29.5 V) Vac / Vdc 150x60x $ W 20 A 24 V (22.5 to 29.5 V) Vac / Vdc 150x115x $ W 40 A 24 V (22.5 to 29.5 V) Vac / Vdc 150x140x $ phase 120 W 5A 24 V (22.5 to 29.5 V) Vac / Vdc 125x40x $ W 10 A 24 V (22.5 to 29.5 V) Vac / Vdc 150x60x $ W 20 A 24 V (22.5 to 29.5 V) Vac / Vdc 150x115x $ W 40 A 24 V (22.5 to 29.5 V) Vac / Vdc 150x140x $ All prices exclude GST. Weidmuller standard terms & conditions of sale also apply. 7

8 PRO-H Industrial Supplies for Extreme Requirements Status Alarms 25 C to +70 C Robust Wide temperature range from 25 C +70 C. Green LED OK Red LED OFF Remote alarms 1G Vibration 15G Shock Shock & Vibration Proof Designed for use in areas of high shock and vibration Reliable 8 Equiped for long reliable service life. High Mean Time Between Failures (MTBF) up to 1.8 Million hours. All prices exclude GST. Weidmuller standard terms & conditions of sale also apply.

9 PRO-H Single-Phase Supplies FOR EXTREME REQUIREMENTS The PRO-H is a new generation of high performance DIN-rail mounted single-phase power supplies designed to work reliably even under the most demanding factory floor conditions. A high power reserve guarantees reliable start-up of loads with high inrush currents such motor starting applications. Excellent electrical specifications and high immunity against fluctuations in input voltage makes these compact modules the best choice to power sensitive loads in industrial process control systems, machine tools or other demanding industrial applications. Industrial grade design Rugged metal case for harsh industrial environments Autoselect input and international safety approvals Variable output voltage Indefinite short circuit, overvoltage and over temperature protection OK signal Remote On/Off Shock and vibration proof Optional panel mounting Redundancy module Max. 70 W 6.5 A 12 Vdc Vac / Vac 110x35x W 13.0 A 12 Vdc Vac / Vac 110x54x W 3.75 A 24 Vdc Vac / Vac 110x35x W 7.5 A 24 Vdc Vac / Vac 110x54x W 15 A 24 Vdc Vac / Vac 125x80x W 25 A 24 Vdc Vac / Vac 125x165x W 4 A 48 Vdc Vac / Vac 110x54x W 7.5 A 48 Vdc Vac / Vac 125x80x W 12.5 A 48 Vdc Vac / Vac 125x165x PRO-H Diode Modules DOUBLE YOUR POWER / REDUNDANCY With a redundancy module and two PRO-H power supplies (of same type) you can configure a highly reliable, truly redundant power system without any additional components. This module enforces the equivalent sharing of the output current by each power supply. The system is fully redundant and provides output power even if one power supply has completely failed e.g by short circuit on the output. In the event that either power supply fails or is disconnected, the second unit will automatically supply the full current to the load. The redundancy of the system is monitored and if lost, indicated by an alarm output. The inputs are hot swappable and can be loaded up to 15 A each. Type CP T RM 10 CP T RM C 40 C 24 Vdc 2 x 24Vdc 15 A 110x35x Vdc 2 x Control 25 A 110x54x

10 INSTAPOWER 1 Phase 25-48W ADJUSTABLE OUTPUT VERSATILITY Max. The new INSTApower single phase 25-48W power supplies provide the answer to a wide range of power supply needs. Just four different modules provide for all output voltages from 4 to 55VDC. An easily accessible trimpot is provided via an access port to enable wide adjustment to meet your requirements. Fully protected against overload INSTApower 48W provides up to 50% over current drive to start your load. Wide range of adjustment & universal AC/DC inputs Suitable for use as a DC/DC Converter Ultra-compact only 70mm wide Mounts on standard TS35 DIN rail Local and International Approvals: CTick, CE, UL, CSA 25 W 5 A 4-8 Vdc Vac/ Vdc 62.5x70.0x $ W 4 A 9-15 Vdc Vac/ Vdc 62.5x70.0x $ W 2 A Vdc Vac/ Vdc 62.5x70.0x $ W 1 A Vdc Vac/ Vdc 62.5x70.0x $ List Price INSTAPOWER 1 Phase 24W FOR DRIVING INDUCTIVE LOADS Max. Devices such as relays, contactors, solenoids and motors all require an initial starting current many times their normal level. The compact INSTAPOWER range has the capacity to supply the initial inrush current to start inductive loads and can actually provide 3 times their rated output for a short duration. Thermal overload protection & automatic restart High Efficiency & universal inputs Compact design only 52mm wide Mounts on standard TS35 DIN rail Suitable for use as a DC/DC converter Local and International Approvals: C Tick, CE, UL, CSA 24 W 2 A 5 Vdc Vac/ Vdc 62.5x52x $ W 1.5 A 12 Vdc Vac/ Vdc 62.5x52x $ W 1.5 A 15 Vdc Vac/ Vdc 62.5x52x $ W 1 A 24 Vdc Vac/ Vdc 62.5x52x $ W 1 A 28 Vdc Vac/ Vdc 62.5x52x $ List Price WAVEPOWER 1 Phase 12W ULTRA COMPACT ONLY 22mm WIDE Compact design and powerful functionality make the WAVEPOWER a very valuable solution to spacing problems in many applications. Slimline only 22.5mm in wide with plug/socket terminals Thermal overload protection & automatic restart Mounts on standard TS35 DIN rail Local and International Approvals: C Tick, CE, UL, CSA Max. 12 W 0.5 A 24 Vdc Vac/ Vdc 92.4x22.5x $ List Price 10 All prices exclude GST. Weidmuller standard terms & conditions of sale also apply.

11 Easyline Chassis Mount LONG SERVICE LIFE EasyLine Chassis Mount Supplies in a range of capacities With outputs from 25 to 250 Watts in industry standard 12, 24 and 48Vdc versions. Efficiencies of up to 87% the new EasyLine from Weidmuller can reduce your power requirements and extend overall service life of your equipment. International approvals and universal input voltages, EasyLine can be installed into equipment bound for any market. Up to 150% overload protection. Stable DC output voltage Wide range input AC/DC OEM Product Long life and high efficiency in a compact chassis mount housing fitted with fingersafe terminations. Extended temperature ratings: -20 C to 70 C and a low 100mV ripple add value to the already high value package. All models feature adjustable output voltage 250 Watt EasyLine with forced coiling keeps size to a minimum Easily accessible terminals with touch safe cover Max. (Watts) No. List Price 25W 1.1 A 24 V Vac / Vdc 105 x 77 x $ W 6 A 12 V Vac / Vdc 135 x 100 x $ W 3.2 A 24 V Vac / Vdc 135 x 100 x $ W 1.6 A 48 V Vac / Vdc 135 x 100 x $ W 6.5 A 24 V Vac / Vdc 205 x 100 x $ W 10.5 A 24 V Vac / Vdc 205 x 100 x $99.95 Accessories Bracket 250W $4.95 All prices exclude GST. Weidmuller standard terms & conditions of sale also apply. 11

12 Weidmuller Solutions Weidmuller is a leading manufacturer of Electrical and Electronic products that are designed, tested and certified to the most stringent Australian and International standards. The extensive Products portfolio encompasses, devices, modules and accessories essential to the requirements of Electrical Engineers, Electricians and Technicians. Weidmuller Products are used worldwide in switchboards, machines and vehicles where ever electrical power is terminated, switched, conditioned or transformed. With over sixty years of experience and our strict attention to quality, reliability and efficient functionality Weidmuller is the sensible choice for all your power electrical and electronic needs. Terminals Markers Industrial Multipole Connectors Supplies Relays & Optocouplers Surge Protection Enclosures Cable Glands Tools Accessories Product Distributors NSW: Sydney Ramelec (NSW) Pty Ltd Phone: (02) Fax: (02) nsw@ramelec.com.au NSW: North & Central Coast PDC Group (Aust) Pty Ltd Phone: (02) Fax: (02) pdce@pdcgroup.com.au NSW: South & Wollongong Excell Control Pty Ltd Phone: (02) Fax: (02) sales@excellcontrol.com.au QLD Ramelec (QLD) Pty Ltd Phone: (07) Fax: (07) qld@ramelec.com.au VIC Quador (Aust) Pty Ltd Phone: (03) Fax: (03) sales@quador.com.au TAS TAS Electrical & Engineering Supplies Phone: (03) Fax: (03) info@taseande.com.au Or contact your local distributor, reseller or wholesaler: SA Ramelec (SA) Pty Ltd Phone: (08) Fax: (08) sales@ramelec.com.au NT Ramelec (NT) Pty Ltd Phone: Fax: sales@ramelec.com.au Weidmuller Pty Ltd (Head Office) 43 Huntingwood Drive, Huntingwood NSW 2148 Phone +61 (0) Fax +61 (0) info@weidmuller.com.au WA JTDay Pty Ltd Phone: (08) Fax: (08) enquiries@jtday.com.au NEW ZEALAND Cuthbert Stewart Limited Phone: +64 (0) Fax: +64 (0) csl@cuthbertstewart.co.nz : WAUS/Supplies2010