PROFINET New Cabling for Gigabit Ethernet End-to-End Link (E2E) Dipl.-Ing. Rainer Schmidt HARTING
Gigabit Ethernet the Technology Driver Gigabit Ethernet state-of-the-art Protocol in the IT More Speed and higher Bandwidth = more Functionality, more Security and higher Efficiency in the Network Reduced Costs by Implementation of Standard-Gigabit Devices in the PROFINET Network High Grade of Compatibility for all Ethernet Components based on the IEEE 802.3x Standards Backwards-Compatibility Fast Ethernet / Gigabit Ethernet
Gigabit Ethernet Compatibility for all PROFINET Applications Backwards Compatibility covered by Standards Ethernet Specification acc. IEEE 802.3 Profile- and Cabling Standards: IEC 61784-5-x (PROFINET x=3) IEC 61918 Ed.3 Industrial Cabling ISO/IEC 24702 Generic Cabling (ISO/IEC 11801-3 in preparation)
Transmission Technology Gigabit Ethernet vs. Fast Ethernet Fast Ethernet acc. 100Base-T, 4-wire Gigabit Ethernet acc. 1000Base-T, 8-wire
New PROFINET Cable for Gigabit Ethernet PIMF Star-Quad
PROFINET Cable for Fast Ethernet PROFINET Cables so-far Star-Quad, screened, 4-wire suitable up to 100MHz, cat.5, for Fast Ethernet Type A (AWG22/1), Type B (AWG22/7), Type C - Hybrid or special designs Jacket in PVC or PUR Installation-friendly by special Cable Design (inner jacket, Easy Stripping Tool)
PROFINET Cable for Gigabit Ethernet New PROFINET Cables SF-UTP or PIMF Design, 8-wire suitable up to 250MHz, cat.6, for Gigabit Ethernet Type A (AWG23/1), Type B (AWG23/7) and Type C available Jacket in PVC or PUR Cabinet Cord as a new Cabling Component in the PROFINET Programme HARTING s PROFINET Cabinet Cord, 8-wire, 4x2xAWG26/7, cat.6
PROFINET Construction Set made by HARTING HIFF HARTING RJ Industrial
PROFINET Construction Set made by HARTING HARTING Industry Form Factor (HIFF) HARTING RJ Industrial RJ45 Coupler 4- / 8-wire RJ45 Jack with IDC / prelink 4-wire PushPull V4 IP65/67 Interface acc. ISO/IEC 24702 (11803-3 in Edition 3) PushPull V14 IP65/67 Interface acc. IEC 61076-3-106 and PROFINET compliant Han 3 A RJ45 RJ45 Jack with IDC / prelink 8-wire IP65/67 Interface acc. IEC 61076-3-106 and PROFINET compliant
PROFINET Cabling complete
PROFINET Cabling Standards, Documents & Declaration Beside the IEC 61784-5-3 (PROFIBUS / PROFINET) Standard you can find a lot of supporting Documents PROFINET Cabling and Interconnection Technology Guideline for PROFINET Version 3.1 Date March 2014 Order No.: 2.252 Description of the E2E Link you can find as TR9902 as Part of the ISO/IEC 11801 Edition 3 (in preparation)
PROFINET Cabling Design Rules the Number of Connections in a PROFINET Cabling System is limited to # 6 by 100m Channel Length max.
Measurement in Cabling PROFINET Cabling can be tested after Installation
Measurement in Generic Cabling Systems Data Transmission Paths within the horizontal Area Permanent Link Channel Note: the connectors on both ends of the Channel will be not counted / tested from Hand-held Tester because they count to the device
Measurement in Generic Cabling Systems Data Transmission Paths within the horizontal Area including CP (Consolidation Point) Installed Basis - Permanent Link Complete Transmission Section - Channel Note: the connectors on both ends of the Channel will be not counted / tested from Hand-held Tester because they count to the device
Measurement in Industrial Cabling Systems Data Transmission Paths within Industrial Areas (Automation Islands) count the two Connectors as Part of the Cabling and hast to bested too! Note: the connectors on both ends of the Industrial Channel has to be tested that is the E2E Link
Measurement in PROFINET Cabling Systems PROFINET Cabling can be tested similar to a Channel but: using PROFINET Test Heads for RJ45 or M12 using the special Firmware of Hand-held Tester (E2E Link) Note: the connectors on both ends of the Industrial Channel has to be tested that is the E2E Link
Measurement in PROFINET Cabling Systems There are Field-Tester available for PROFINET Cabling Tests (Approval Tests NOT for Trouble Shooting!) Source: IDEAL_Industries, FLUKE Networks, Psiber
PROFINET Cabling Test For PROFINET Cabling Tests the E2E Link has to be checked Possible Procedure e.g. with LanTEK Tester Tester has to be loaded and switched ON Nullabgleich Normalisation of the Devices (see Operation Instruction) further Preparation: enter Name and Date, prepare a Folder aom. choose the Cabling Standard PROFINET E2E enter the NVP Value of the Cable installed for PROFINET 4-wire Cables usually it is 66 otherwise double-check Data Sheet of the Cable connect all PROFINET Adapters with the Tester and the PROFINET Cabling Section you want to test Start / Run Autotest store the Results