PNEUMATIC TOGGLE SWITCHES

CONTROLS PNEUMATIC TOGGLE SWITCHES AIR00* SERIES Single Control Part No Kit No (indludes airline & fi ttings) 100.1.24 AIR001 Twin 100.1.42 AIR002 Triple 100.1.60 AIR003 Quad 100.1.122 AIR004 18/07/2008

CONTROLS PNEUMATIC DUAL TIPPER CONTROL Air proportional cab switch with full integrated lever to control both PTO engagement and body tipping / lowering. Several versions available to meet any requirements. 60 Functional diagram 68 72 113 4 x 6, 3 60 4x 11 6mm air fittings 72 Available versions PTO control Auto-disengage Non auto-disengage Without PTO control 100-001-61094 100-001-61067 100-001-61101 18/07/2008

CONTROLS OPTIONS 100 100-002-60049 Mounting tower for KIP-AIR H = 80mm. 100-002-60067 Bracket for KIP-AIR mouning. With this kit you can also fit a pneumatic switch (see below) to control auxillary applications. 100-002-60094 Multi-position bracket for KIP-AIR. 100-002-60101 2-way pneumatic selector to be coupled with bracket p/n 100-002-60067. OUT IN 100-002-00032 Pressure signal switch assembly. 18/07/2008

CONTROLS PROPORTIONAL PNEUMATIC TIPPER CONTROL COMPLETE CONTROL SYSTEM FOR TRUCK & DOG APPLICATION 100.8.60016 - Control only AIR030 - Control c/w airline & fittings FUNCTIONS PTO Truck raise/lower Truck tailgate Trailer raise/lower Trailer tailgate Dog lock FEATURES: - Innovative, ergonomic design - Slow lower hoist control - PTO & Dog lock LED indicators - Individually replaceable switches Functional data Nominal diameter Max. working pressure Working temperature range Ø 4 mm 12 BAR -30 90 C - Custom configurations available Lamp voltage 12-24V 04/09/2008

CONTROLS 9000 SERIES Complete electro-pneumatic control systems for tipper applications SWITCH BOX Mounts inside cabin SOLENOID BOX Mounts outside cabin STANDARD FEATURES Push-button rocker switches No airlines required to enter cabin Powder coated cabin control box Sturdy, aluminium solenoid box Pre-fi tted, push-in air fi ttings Single air supply for all functions Manual over-ride system Various mounting options Simple, plug-together, colour-coded wiring MODEL FUNCTIONS SWITCHES EP9001.* PTO, Hoist, Tailgate In box EP9001CH.* PTO, Hoist, Tailgate Suit dash knockouts # EP9002.* PTO, 2 x Hoists, 2 x Tailgates, Dog lock In box EP9002CH.* PTO, 2 x Hoists, 2 x Tailgates, Dog lock Suit dash knockouts # * 12 or 24 Volt DC # Not shown Custom configurations available 05/09/2008

VALVES CABLE TIPPING VALVE Optional Mechanical tipping valve operated by cable controls series LINEA or LINEA BLOCK to suit light duty tipper trucks. Open centre hydraulic scheme according to CE standards. - Built-in check and adjustable safety valves. - Either Chassis or tank (DSM kit) mounting options. - Mechanical Direct End-of-stroke with anti-shock spring. - Ready for pressure signal switch mounting. - Cataphoresis coated body and nickel spool. - Compact size. - Guaranteed for oil temperature range -25 80 C, viscosity range 12 100 cst and oil filtering 25 µm. Tipping valve type Order code IN TANK OUT Weight ISO 228 ISO 228 ISO 228 kg FM-45 CE 121-010-00207 G 1/2 G 1/2 G 1/2 2.2 04/08/2008

VALVES FM-45 MECHANICAL TIPPING VALVE 121-010 Tipping valve type Order code Pressure values Flow Standard pressure setting Max. pressure setting bar bar l/min FM-45 CE 121-010-00207 140 200 50 Tipping valve pressure drops p-q operating curve for pressure relief valves Δp(bar) 4 p (bar) 200 3 2 IN-OUT OUT-TANK 150 100 1 50 10 20 30 40 50 60 Q (l/min) 10 20 30 40 50 60 Q (l/min) The graph refers to oil type ISO VG 46 at 50 Mounting plate for tank 121-991-00112 Functional diagram Seal kit 121-900-00406 Mounting kit 121-994-00306 Qty Description 4 Screw M8 TCE L=60 4 Washer M8 4 Spring washer M8 1 Gasket 04/08/2008

VALVES ELECTRIC TIPPING VALVE Optional Electric tipping valve operated by switch to suit light duty tipper trucks. Open centre hydraulic scheme according to CE standards. - Built-in check and adjustable safety valves. - Either Chassis or tank (DSE kit) mounting options. - Ready for pressure signal switch mounting. - Cataphoresis coated body and nickel spool. - Compact size. - Guaranteed for oil temperature range -25 80 C, viscosity range 12 100 cst and oil filtering 25 µm. Tipping valve type Order code IN TANK OUT Weight ISO 228 ISO 228 ISO 228 kg FE-40 CE 12V 121-004-00572 G 1/2 G 1/2 G 1/2 3.1 FE-40 CE 24V 121-004-00581 04/08/2008

VALVES FE-40 ELECTRIC TIPPING VALVE 121-004 Tipping valve type Order code Pressure values Flow FE-40 CE 12V 121-004-00572 FE-40 CE 24V 121-004-00581 Standard pressure setting Max. pressure setting bar bar l/min 140 240 40 Δp(bar) Tipping valve pressure drops 8 p-q operating curve for pressure relief valves p (bar) 200 6 4 OUT-TANK 150 100 2 IN-OUT 50 10 20 30 40 50 60 Q (l/min) 10 20 30 40 50 60 Q (l/min) The graph refers to oil type ISO VG 46 at 50 Mounting plate for tank 121-991-00112 Functional diagram Seal kit 121-900-00577 Mounting kit 121-994-00306 Qty Description 4 Screw M8 TCE L=60 4 Washer M8 4 Spring washer M8 1 Gasket 04/08/2008

VALVES PNEUMATIC TIPPING VALVE PROPORTIONAL Optional Pneumatic proportional tipping valve to suit medium-light duty tipper trucks. Operated by pneumatic switch series LAM (fast and slow lowering) or by proportional cab controls (proportional lowering). Open centre hydraulic scheme according to CE standards. - Built-in check and adjustable safety valves (direct type). - Modular cast-iron body for pressure up to 400 bar. - Either Chassis or tank (DSP kit) mounting options. - Mechanical Direct End-of-stroke with anti-shock spring. - Ready for pressure signal switch mounting. - Cataphoresis coated body and nickel spool. - Compact size. - Guaranteed for oil temperature range -25 80 C, viscosity range 12 100 cst and oil filtering 25 µm. Tipping valve type Order code IN TANK 1 TANK 2 OUT Weight ISO 228 ISO 228 ISO 228 ISO 228 kg FP 80 MODULAR 121-010-10054 G 1/2 G 3/4 G3/8 G 1/2 2.5 04/08/2008

VALVES FP-80 MODULAR PNEUMATIC TIPPING VALVE 121-010 Tipping valve type Order code Pressure values Flow Standard pressure setting Max. pressure setting bar bar l/min FP-80 MODULAR 121-010-10054 140 300 80 Tipping valve pressure drops p-q operating curve for pressure relief valves Δp(bar) p (bar) 8 6 IN-OUT 240 180 4 2 OUT-TANK 2 OUT-TANK 1 120 60 15 30 45 60 75 90 Q (l/min) 20 40 60 80 100 120 Q (l/min) The graph refers to oil type ISO VG 46 at 50 Mounting plate for tank 121-991-00112 Functional diagram Seal kit 121-900-00700 Mounting kit 121-994-00306 Qty Description 4 Screw M8 TCE L=60 4 Washer M8 4 Spring washer M8 1 Gasket 04/08/2008

VALVES PNEUMATIC TIPPING VALVE PROPORTIONAL Optional Proportional pneumatic tipping valve to suit medium-heavy duty tipper trucks. Operated by proportional cab control. Open centre hydraulic scheme according to CE standards. - Built-in check and adjustable safety valves ( Pilot type). - Modular cast-iron body for pressure up to 400 bar. - Either Chassis or tank (DSP kit) mounting options. - Mechanical Direct End-of-stroke with anti-shock spring. - Ready for pressure signal switch mounting. - Cataphoresis coated body and nickel spool. - Compact size thanks to front ports. - Guaranteed for oil temperature range -25 80 C, viscosity range 12 100 cst and oil filtering 25 µm. Tipping valve type Order code IN TANK 1 MODULAR 150 CE 121-008-00309 G 3/4 G 1 TANK 2 OUT Weight ISO 228 ISO 228 ISO 228 ISO 228 kg G 1/2 G 3/4 5.8 04/08/2008

VALVES MODULAR 150 PILOT PNEUMATIC TIPPING VALVE 121-008 Tipping valve type Order code Pressure values Flow Standard pressure setting Max. pressure setting bar bar l/min MODULAR 150 CE 121-008-00309 160 350 150 Tipping valve pressure drops p-q operating curve for pressure relief valves Δp(bar) 8 p (bar) 240 6 180 4 IN-OUT OUT-TANK 2 OUT-TANK 1 120 2 60 30 60 90 120 150 180 Q (l/min) 30 60 90 120 150 180 Q (l/min) The graph refers to oil type ISO VG 46 at 50 Mounting plate for tank 121-991-00112 Mounting plate for tank 121-991-00194 Functional diagram Seal kit 121-900-01058 Mounting kit 121-994-00404 Qty Description 4 Screw M8 TCE L=70 4 Washer M8 4 Spring washer M8 1 Gasket 04/08/2008

VALVES PNEUMATIC TIPPING VALVE PROPORTIONAL Optional Proportional pneumatic tipping valve suitable for large oil flow applications especially designed for heavy-duty tipper bodies, off-road trucks and semi-trailers. Operated by proportional cab control. Open centre hydraulic scheme according to CE standards. - Built-in check and adjustable safety valves (pilot type). - Modular cast-iron body for pressure up to 400 bar. - Either Chassis or tank mounting options. - Mechanical Direct End-of-stroke with anti-shock spring. - Ready for pressure signal switch mounting. - Cataphoresis coated body and nickel spool. - Guaranteed for oil temperature range -25 80 C, viscosity range 12 100 cst and oil filtering 25 µm. Tipping valve type Order code IN TANK OUT Weight ISO 228 ISO 228 ISO 228 kg MODULAR 250 CE 121-008-00210 G 1 G 1 G 1 6.8 04/08/2008

VALVES MODULAR 200-250 PILOT PNEUMATIC TIPPING VALVE 121-008 Tipping valve type Order code Pressure values Flow Standard pressure setting Max. pressure setting bar bar l/min MODULAR 250 CE 121-008-00210 180 350 250 Tipping valve pressure drops p-q operating curve for pressure relief valves Δp(bar) 12 p (bar) 240 9 IN-OUT 180 6 OUT-TANK 120 3 60 50 100 150 200 250 300 Q (l/min) 45 90 135 180 225 270 Q (l/min) The graph refers to oil type ISO VG 46 at 50 Mounting plate for tank 121-991-00194 Mounting plate for chassis 121-991-00069 Functional diagram Seal kit 121-900-02057 Mounting kit 121-994-00502 Qty Description 3 Screw M10 TCE L=100 3 Washer M10 3 Spring washer M10 1 O-ring 04/08/2008

VALVES PNEUMATIC TIPPING VALVE TRUCK & TRAILER - Built-in check valve and safety valve (DIRECT type). - Modular cast-iron body for pressure up to 400 bar. - Guaranteed for oil temperature range -25 80 C, viscosity range 12 100 cst and oil filtering 25 µm. - Cataphoresis coated body and nickel spool. Functional diagram Tipping valve type Order code IN TANK OUT A/B Weight ISO 228 ISO 228 ISO 228 kg DM 250 CE 121-15-51 G 1 G 1-1/4 G 1 25 04/08/2008

VALVES DM 250 DOUBLE SECTION PROPORTIONAL TIPPING VALVE 121-015 Tipping valve type Order code Pressure values Flow Standard pressure setting Max. pressure setting bar bar l/min DM 250 CE 121-015-00051 140 300 250 Δp(bar) Tipping valve pressure drops 13,5 IN-OUT (B) 12 10,5 9 7,5 6 4,5 OUT-TANK (B) 3 1,5 IN-OUT(A) OUT-TANK (B) 40 60 80 100 120 140 160 180 200 220 240 260 Q (l/min) p-q operating curve for pressure relief valves p (bar) 280 210 140 70 50 100 150 200 250 300 Q (l/min) The graph refers to oil type ISO VG 46 a 50 04/08/2008

VALVES 3-WAY HIGH PRESSURE MANUAL DIVERTER VALVES Manual 3-way high pressure diverter valve to control 2 pressure lines separately. Especially designed to accommodate pressure peaks in applications like tipper/crane or hook-loader/crane. - 3/4 thread for flow up to 100 l/min. - Pressure up to 400 bar. - Open centre scheme to prevent dangerous shocks while switching. - Body comes with anti-corrosion coating and nickel spool. 121-19-128 121-19-351 121-19-1001 W 73.3 78.8 90.5 X 86 88 98 Y 91.6 99 108.5 Z 154.5 154.5 204 A/B/P 1/2 G 3/4 G 1 G Functional diagram Tipping valve type Order code Port Pressure Flow Weight Max Peak DVT VLV 3 WAY bar bar l/min kg 121-019-00128 1/2 1.8 110 121-019-00351 3/4 380 400 2.15 121-019-01001 1 150 3.7 11/08/2008

VALVES PNEUMATIC DIVERTER VALVE Pneumatic 3-way high pressure diverter valve to control 2 pressure lines separately. Especially designed for applications like Tipper/Crane or Truck/Trailer. - Flow up to 250 l/min. - Pressure up to 300 bar. - Open centre scheme to prevent dangerous shocks while switching. - Body c/w anti-corrosion coating and Nickel spool. Functional diagram N 2 holes G 3/4" N 4 holes Ø8.5mm Tipping valve type Order code Pressure Flow Weight In service Max peak pressure bar bar l/min kg SEL 250-2 121-022-00132 300 350 250 2.5 04/08/2008

VALVES MECHANICAL HYDRAULIC END-OF-STROKE VALVE End of stroke valve especially designed for trailers and semi-trailers either with 1 or 2 pipe configurations. The special hydraulic scheme allows the valve to be used for either open or closed center circuits. Furthermore it prevents the cylinder from any pressure peaks. The innovative and compact design makes the fitting easier and cost effective. - Mechanical runstop valve. - Flow up to 200 l/min. - Cast iron body resistant to pressure up to 400 bar. - Body c/w anti-corrosion coating and Nickel spool. - Pressure switch option. - High-resistance anti-shock spring. Optional Pressure drops Functional diagram p (bar) 1,5 1 0,5 50 100 150 200 250 300 Q (l/min) Tipping valve type Order code Pressure Flow Weight Max pressure bar l/min kg RUNSTOP 200 121-035-00200 350 200 4.8 04/08/2008

VALVES RUNSTOP 200 END-OF-STROKE VALVE 121-035-00200 1 Hose configuration (recommended) By this configuration the RUNSTOP valve interupts the oil flow to the cylinder and the delivery is diverted to the outlet through the safety valve of the main tipping valve. In this case we recommend to use tipping valves c/w piloted safety valves like our modular pilot valve series. Ready for rear gate control Inlet Outlet 2 Hose configuration By this configuration the RUNSTOP valve interupts the oil flow to the cylinder and the delivery is diverted to the oulet through the second pipe connected to the oil tank. Ready for rear gate control Outlet Inlet Tank 04/08/2008

ACCESSORIES Hydraulic cylinders Light industrial type BORE ROD DIA. Installation Guide A B C D E F G H I J K L M 1 ½ 7/8 145 48 9/16 22 75 39 32 38 5/8 50 34 14 48 2 1 ¼ 150 60 9/16 22 80 34 38 38 3/4 68 34 20 60 This rugged, quality constructed hydraulic cylinder ensures fitment into situations where a short closed length cylinder is important. The 1 1/2" bore cylinders have standard stroke lengths of 4,6,8,10 & 12 inches. The 2" bore cylinders have standard stroke lengths of 4,6,8,10,12,14,16,18 & 20 inches. Non-standard strokes can be manufactured upon request. 31/07/2008

ACCESSORIES Hydraulic cylinders Agricultural type BORE ROD DIA. Installation Guide A B C D E F G H I J K L M N O P Q 2 1 ¼ 311 61 9/16 22 76 202 153 75 50 27 27 51 68 50 25 27 51 2 ½ 1 ½ 311 73 3/4 30 82 174 109 82 52 28 27 65 80 50 26 27 59 3 1 ½ 311 87 3/4 30 84 169 104 82 52 28 27 65 94 50 26 27 59 3 ½ 1 ¾ 311 100 3/4 30 84 169 104 82 52 28 27 65 111 50 26 27 59 4 1 ¾ 311 114 3/4 30 88 158 93 82 52 28 27 65 N/A 50 32 27 59 5 2 311 143 3/4 30 88 163 91 85 55 32 28 78 N/A 50 32 27 78 2, 2 ½, 3 & 3 ½ cylinders have external gland nut. 4 & 5 cylinders have internal threaded gland. 5 cylinders with strokes over 24 have a 2 ½ diameter piston rod. All cylinders supplied with 1 diameter clevis pins and clips. Standard stroke lengths - 6 8 10 12 14 16 18 20 24 30 36 48 Other strokes available on request. 31/07/2008

ACCESSORIES V-bottom hydraulic tanks Powdercoated steel Integral mounting angles V design allows sediment to settle safely on bottom of tank A C B 100 D Model Capacity A B C D L (gal UK) mm WF104K 23 (5) 380 200 290 255 WF101K 45 (10) 380 200 290 510 WF102K 68 (15) 400 235 300 610 WF103K 90 (20) 550 300 390 510 2 x 1 1/4 BSPT ports in bottom of tank Filler/breather included 04/08/2010

ACCESSORIES TIPPER STYLE OIL TANK Part number - 135.498.157 TANK WITH PAD MOUNT FOR DIRECT TIPPING VALVE MOUNTING Capacity - 15L 4 472 532 5 Not included N Code Description Q. 1 505-003-00015 Nut M8 4 2 501-007-00064 Washer M8 4 3 507-003-00235 Gasket 1 4 509-005-00015 Breather cap 1 121-010-00207 Cable valve n/a 5 121-004-00572 Electric valve 12V n/a 121-004-00581 Electric valve 24V n/a 121-010-10054 Pneumatic valve n/a 1 2 3 06/08/2008

ACCESSORIES TIPPER STYLE OIL TANK Part number - 135.498.10306 TANK WITH PAD MOUNT FOR DIRECT TIPPING VALVE MOUNTING Capacity - 30L 3 N Code Description Q. 1 505-003-00015 Nut M8 4 2 501-007-00064 Washer M8 4 3 509-005-00015 Breather cap 1 4 507-003-00244 Gasket 1 121-010-00207 Cable valve 5 121-004-00572 Electric valve 12V 121-004-00581 Electric valve 24V n/a 121-010-10054 Pneumatic valve 1 2 5 Not included 4 08/09/2010

ACCESSORIES 135.500 SERIES OIL TANKS Steel tanks finished in grey epoxy powder. Equipped with filler/breather cap and oil level sight glass. 40 L 60 L 135.500.401 135.500.652 06/08/2008

ACCESSORIES SIDE MOUNT TANK WITH FILTER PLATE Based on the latest technology, these tanks are produced to ensure maximum reliability and longer life as well as an appearance that can be perfectly integrated into any application. They are supplied complete with support brackets, straps and rubbers, filler cap and breather with replaceable air filter, oil level gauge and flange for filter options. A wide range of accessories are available to complement the high-quality powder coated finish. Tank capacity Useful Litres Order code Steel 100 135-600-11005 23/12/2009

ACCESSORIES 135-600-1 HOW TO ORDER SIDE MOUNT TANKS Filter and mounting flange for tipping valve. Modular 150AL - Modular 250 See tipping valves catalogue Mounting flange for tipping valves (see table 5) Wheel base 115 121-994-00226 Submerged filter (see table 3) 30 µm 118-001-12167 60 µm Wheel base 115 118-001-11168 Filter without mounting flange for tipping valves. 90 µm 70 L 118-001-00125 110 L 118-001-00134 60 L 118-001-01106 60 µm 100 L 118-001-01151 200 L 118-001-01259 Flangible filter (see table 1) Wheel base 115 30 µm 48 L 118-001-02105 72 L 118-001-02150 140 L 118-001-02258 25 µm 40 L 118-001-04103 65 L 118-001-04158 10 µm 42 L 118-001-03104 68 L 118-001-03159 23/12/2009

ACCESSORIES SIDE MOUNT TANKS WITH FILTER PLATE Based on the latest technology, these tanks are produced to ensure maximum reliability and longer life as well as an appearance that can be perfectly integrated into any application. They are supplied complete with support brackets, straps and rubbers, filler cap and breather with replaceable air filter, oil level gauge and flange for filter options. A wide range of accessories are available to complement the high-quality powder coated finish. Tank capacity Order code Dimensions Useful Litre Steel A B mm 135 135-610-01354 350 190 200 135-610-02004 500 290 03/04/2009

ACCESSORIES 135-610 HOW TO ORDER SIDE MOUNT TANKS Filter and mounting flange for tipping valve FM/FP80 - Modular 150AL Modular 150AL - Modular 250 135 L 200 L See tipping valves catalogue Mounting flange for tipping valves 135 L 200 L pcd 115 pcd 175 121-994-00182 121-994-00217 Submerged filter 135 L 200 L 30 µm 60 µm pcd 115 118-001-12158 118-001-11159 30 µm pcd 118-001-12756 60 µm 175 118-001-11757 Filter without mounting flange for tipping valves Flangible filter pcd 135 L 115 pcd 200 L 175 90 µm 70 L 118-001-00125 110 L 118-001-00134 60 L 118-001-01106 60 µm 100 L 118-001-01151 200 L 118-001-01259 48 L 118-001-02105 30 µm 72 L 118-001-02150 140 L 118-001-02258 25 µm 40 L 118-001-04103 65 L 118-001-04158 10 µm 42 L 118-001-03104 68 L 118-001-03159 90 µm 190 L 118-001-00189 60 µm 180 L 118-001-01204 30 µm 130 L 118-001-02203 25 µm 115 L 118-001-04201 10 µm 120 L 118-001-03202 03/04/2009

POWERPACKS M301 Single acting manual Description: Pump/Motor/Reservoir Unit Manually Operated 2-Way/2-Position Normally Closed Valve With Motor Start Switch Check Valve Externally Adjustable Relief Valve 1/4 NPT Port Horizontal Mounting Standard M HYDRAULIC SCHEMATIC 1/4 NPT Outlet 19mm C 153mm 19mm A SIDE VIEW 35mm B Mounting Holes 3/8 UNC 83mm 64mm D END VIEW Relief Valve ORDERING CODE: M301.14157.12V 12V or 24V DC TANK VOLUME TYPE A litres material / shape B C D mm 14157 3.2 Poly 461 254 152 165 6148 3.8 Steel 486 279 159 153 14166 4.7 Poly 486 279 184 170 6864 8.3 Steel 658 451 159 184 6888 11.7 Steel 811 604 159 184 04/08/2008

POWERPACKS M310 Double acting manual Description: Pump/Motor/Reservoir/Valve Check Valve 4-Way Manually Operated Valve With Cam Actuated Motor Start Switch Externally Adjustable Relief Valve 1/4 NPT Ports Horizontal Mounting Standard A B M HYDRAULIC SCHEMATIC 1/4" NPT Outlets 325mm Relief Valve C 153mm 19mm 35mm B 83mm SIDE VIEW ORDERING CODE: M310.14157.12V A 12V or 24V DC Mounting Holes 3/8 UNC D END VIEW TANK VOLUME TYPE A litres material / shape B C D mm 14157 3.2 Poly 461 254 171 165 6148 3.8 Steel 486 279 178 153 14166 4.7 Poly 486 279 203 170 6864 8.3 Steel 658 451 178 184 6888 11.7 Steel 811 604 178 184 04/08/2008

POWERPACKS M319 Single acting solenoid Description: Pump/Motor/Reservoir/Valve Check Valve 2-Way/2-Position Normally Closed Solenoid Operated Lowering Valve Externally Adjustable Relief Valve 3/8 BSP Outlet Horizontal Mounting Standard Option: Push-button pendant control c/w 2 metres cable 62mm Model: 07993 16mm 110mm M 35mm 46mm 55mm HYDRAULIC SCHEMATIC 3/8 BSP Outlet 19mm 181mm Relief Valve C 153mm 19mm SIDE VIEW ORDERING CODE: M319.14157.12V A 35mm B 12V or 24V DC Mounting Holes 3/8 UNC 83mm D END VIEW TANK VOLUME TYPE A litres material / shape B C D mm 14157 3.2 Poly 461 254 152 165 6148 3.8 Steel 486 279 159 153 14166 4.7 Poly 486 279 184 170 6864 8.3 Steel 658 451 159 184 6888 11.7 Steel 811 604 159 184 04/08/2008

POWERPACKS M3551 Double acting solenoid Description: Pump/Motor/Reservoir/Valve Check Valve Externally Adjustable Relief Valve 1 x 4-Way/2-Position and 1 x 2-Way/2-Position Normally Closed Solenoid Cartridge Valve Located in the Base C1 Port Positively Checked Externally Adjustable Relief Valve in C2 Port 9/16 UNO Ports Horizontal Mounting Standard C2 OPTIONAL C1 Option: Push-button pendant control c/w 3 metres cable 62mm M Model: 07995 16mm 110mm 35mm 46mm 55mm HYDRAULIC SCHEMATIC C2 Outlet C1 Outlet 48mm 187mm Relief Valve C 153mm 19mm A SIDE VIEW 35mm B Mounting Holes 3/8 UNC 83mm D END VIEW ORDERING CODE: M3551.14157.12V 12V or 24V DC TANK VOLUME TYPE A litres material / shape B C D mm 14157 3.2 Poly 461 254 152 165 6148 3.8 Steel 486 279 159 153 14166 4.7 Poly 486 279 184 170 6864 8.3 Steel 658 451 159 184 6888 11.7 Steel 811 604 159 184 04/08/2008

POWERPACKS M3515 Double acting solenoid (open centre) Description: Pump/Motor/Reservoir/Valve Check Valve in "P" Port Externally Adjustable Relief Valve D03 Solenoid Valve 9/16 UNO Outlets Horizontal Mounting Standard Option: Push-button pendant control c/w 3 metres cable Model: 07995 16mm 110mm 62mm M 35mm 46mm 55mm HYDRAULIC SCHEMATIC 9/16 UNO Outlet 189mm 153mm 19mm A 35mm B 83mm 41mm SIDE VIEW ORDERING CODE: M3515.14157.12V Mounting Holes 3/8 UNC 12V or 24V DC 245mm END VIEW TANK VOLUME TYPE A litres material / shape B mm 14157 3.2 Poly 461 254 6148 3.8 Steel 486 279 14166 4.7 Poly 486 279 6864 8.3 Steel 658 451 6888 11.7 Steel 811 604 04/08/2008

POWERPACKS M3504 Motor pump tank unit Description: Add Standard or Custom Manifolds to a Basic Power Unit with "P" and "T" Ports. Modular Manifolds Mount to Standard Pad. Allow for a Building Block Approach to Power Unit Flexibility and Circuit Design. For Use With All Monarch Pumps, Motors, and Reservoirs. Note - A spacer may be required with certain reservoirs, on others the valve package may cover reservoir fill and return ports - consult factory. Check Valve Installs In Outlet Port. (Optional) M "P" "T" HYDRAULIC SCHEMATIC Return Outlet 102mm Adjustable Relief Valve C 153mm 19mm 35mm A B Mounting Holes 3/8 UNC 83mm D SIDE VIEW END VIEW ORDERING CODE: M3504.14157.12V 12V or 24V DC TANK VOLUME TYPE A litres material / shape B C D mm 14157 3.2 Poly 461 254 152 165 6148 3.8 Steel 486 279 159 153 14166 4.7 Poly 486 279 184 170 6864 8.3 Steel 658 451 159 184 6888 11.7 Steel 811 604 159 184 04/08/2008

POWERPACKS M326 Motor pump unit Description: Pump Motor Unit Check Valve Externally Adjustable Relief Valve 3/8 NPT Suction 3/8 NPT Outlet 1/8 NPT Relief Valve Return Port M HYDRAULIC SCHEMATIC 3/8 NPT 1/8" NPT Relief Valve Return 67mm 200mm 84mm Relief Valve 3/8" NPT Suction 19mm 153mm 54mm 331mm SIDE VIEW 48mm 57mm Mounting Holes 3/8 UNC 83mm 115mm END VIEW ORDERING CODE: M326.12V 12V or 24V DC 04/08/2008

POWER TAKE-OFFS PTOs FOR ANY APPLICATION Cable shift Air shift Vacuum shift Electric shift Side mount Rear of countershaft Heavy-duty models Various output configurations available GTS can supply power take-offs for the following transmissions: Aisin Allison Daihatsu Eaton Ford Fuller Hino Isuzu Iveco Jatco Mack Mazda Mercedes Mitsubishi New Process Nissan Renault Roadranger Rockwell Scania Spicer Toyota Volvo ZF 31/03/2008

GEAR PUMPS NPLA DIN 3-BOLT Fluid Kinematic viscosity suggested Mineral or synthetic compatible with the following seals: NBR, FKM, FPM, Nylon Average ambient temp. ( C) < -10-10 10 10 35 > 35 VG (cst = mm 2 /s) 22 32 46 68 Optimale kinematic viscosity Max kinematic viscosity suggested at the start-up VG= 10 cst 100 cst VG= 750 cst Viscosity index suggested VI > 100 Oil filtering Inlet pressure Pump rotation > 200 bar: 10 µm < 200 bar: 25 µm -0,3 2 bar Unidirectional Pump type Rotation IN OUT A B Right Left ISO 228 ISO 228 mm mm NPLA-10 105-003-00111 105-003-00102 138 98 NPLA-16 105-003-00175 105-003-00166 147,5 102 NPLA-20 105-003-00219 105-003-00200 154 102 G 3/4 G 1/2 NPLA-25 105-003-00264 105-003-00255 162 102 NPLA-32 105-003-00335 105-003-00326 173 102 NPLA-40 105-003-00415 105-003-00406 188 106 07/08/2009

GEAR PUMPS NPLA GEAR PUMPS 105-003 TECHNICAL FEATURES Pump type Displacement Pressure P1 P2 P3 Max. continuous speed Max. intermittent speed Min. speed cm 3 /rev bar bar bar rpm rpm rpm NPLA-10 10,062 NPLA-16 16,035 NPLA-20 20,123 200 220 240 2200 3000 NPLA-25 25,154 NPLA-32 32,042 180 200 220 2000 2800 NPLA-40 39,933 150 170 190 1800 2500 300 P1= Max. continuous pressure (100%) P2= Max. Intermittent pressure (20 sec.max.) P3= Max. peak pressure (6 sec.max) SUCTION/DELIVERY IDENTIFICATION: Anti-clockwise rotation, left pump Clockwise rotation, right pump 07/08/2009

GEAR PUMPS NPLH DIN 3-BOLT Fluid Kinematic viscosity suggested Mineral or synthetic compatible with the following seals: NBR, FKM, FPM, Nylon Average ambient temp. ( C) < -10-10 10 10 35 > 35 VG (cst = mm 2 /s) 22 32 46 68 Optimale kinematic viscosity Max kinematic viscosity suggested at the start-up VG= 10 cst 100 cst VG= 750 cst Viscosity index suggested VI > 100 Oil filtering > 200 bar: 10 µm < 200 bar: 25 µm Inlet pressure -0,3 2 bar Pump rotation Bidirectional Pump type Order code IN OUT A B Weight ISO 228 ISO 228 mm mm kg NPLH-6 105-004-10065 132 98.5 4,7 NPLH-10 105-004-10109 138 104.5 5 G 1/2 G 1/2 NPLH-16 105-004-10163 147,5 101.5 5,3 NPLH-20 105-004-10207 154 108 5,7 NPLH-25 105-004-10252 162 113 5,9 NPLH-32 105-004-10323 G 3/4 G 3/4 173 124 6,3 NPLH-40 105-004-10403 188 135 04/08/2008

GEAR PUMPS NPLH 13 DIN REVERSIBLE GEAR PUMPS 105-004 TECHNICAL FEATURES Pump type Displacement Pressure Max. continuous speed P1 P2 P3 Max. intermittent speed Min. speed cm 3 /rev bar bar bar rpm rpm rpm NPLH-6 NPLH-10 6,288 10,062 280 310 325 NPLH-16 16.035 2200 3000 NPLH-20 20.123 260 280 290 NPLH-25 25.154 220 250 260 NPLH-32 32.042 190 210 220 2000 2800 NPLH-40 39,933 160 180 190 1800 2500 300 P1= Max. continuous pressure (100%) P2= Max. intermittent pressure (20 sec.max.) P3= Max. peak pressure (6 sec.max) SUCTION/DELIVERY IDENTIFICATION: Anti-clockwise rotation, left pump Clockwise rotation, right pump 04/08/2008

GEAR PUMPS NPH UNI 3-BOLT Fluid Kinematic viscosity suggested Mineral or synthetic compatible with the following seals: NBR, FKM, FPM, Nylon Average ambient temp. ( C) < -10-10 10 10 35 > 35 VG (cst = mm 2 /s) 22 32 46 68 Optimal kinematic viscosity Max kinematic viscosity suggested at the start-up VG= 10 cst 100 cst VG= 750 cst Viscosity index suggested VI > 100 Oil filtering > 200 bar: 10 µm < 200 bar: 25 µm Inlet pressure Pump rotation -0,3 2 bar Unidirectional (Right or Left) Pump type Rotation IN OUT 1 Right Left OUT 2 A B Weight ISO 228 ISO 228 ISO 228 mm mm kg NPH-17 105-011-00175 105-011-00184 152.5 103.5 8.5 G 1/2 NPH-22 105-011-00228 105-011-00237 G 1/2 156 105.5 9 NPH-27 105-011-00273 105-011-00282 158.5 108 9.5 NPH-34 105-011-00344 105-011-00353 G 3/4 163.5 109 10.5 NPH-43 105-011-00433 105-011-00442 169.5 114 11 NPH-51 105-011-00513 105-011-00522 174.5 114.5 11.5 G 3/4 NPH-61 105-011-00611 105-011-00620 G1 180.5 120.5 12 NPH-73 105-011-00737 105-011-00746 188.5 119.5 12.5 NPH-82 105-011-00826 105-011-00835 193.5 124.5 13 NPH-100 105-011-01003 105-011-01012 G1 1/4 210.5 138.5 14 G 1 G 3/4 NPH-125 105-011-01254 105-011-01263 226.5 142.5 16 04/08/2008

GEAR PUMPS NPH UNI GEAR PUMPS 105-011 TECHNICAL FEATURES Pump type Displacement Pressure Max. continuous speed P1 P2 P3 Max. intermittent speed Min. speed cm 3 /rev bar bar bar rpm rpm rpm NPH-17 NPH-22 17.04 22.15 290 315 325 2500 3000 NPH-27 26.18 NPH-34 33.88 280 300 310 2200 2800 NPH-43 43.12 270 290 300 NPH-51 50.82 240 260 280 2000 2500 NPH-61 60.06 220 240 250 1800 2000 NPH-73 72.88 200 220 230 1600 NPH-82 81.08 190 210 220 NPH-100 98.18 180 200 220 1500 1800 NPH-125 122.72 160 180 200 300 P1= Max. continuous pressure (100%) P2= Max. Intermittent pressure (20 sec.max.) P3= Max. peak pressure (6 sec.max) DIRECTION OF ROTATION: Anti-clockwise rotation, left pump Clockwise rotation, right pump 04/08/2008

GEAR PUMPS NPH ISO 4-BOLT Fluid Kinematic viscosity suggested Mineral or synthetic compatible with the following seals: NBR, FKM, FPM, Nylon Average ambient temp. ( C) < -10-10 10 10 35 > 35 VG (cst = mm 2 /s) 22 32 46 68 Optimale kinematic viscosity Max kinematic viscosity suggested at the start-up VG= 10 cst 100 cst VG= 750 cst Viscosity index suggested VI > 100 Oil filtering Inlet pressure Pump rotation > 200 bar: 10 µm < 200 bar: 25 µm -0,3 2 bar Unidirectional (Right or Left) Pump type Rotation IN OUT 1 Right Left OUT 2 A B Weight ISO 228 ISO 228 ISO 228 mm mm kg NPH-17 105-011-10173 105-011-10182 168.5 119.5 11 G 1/2 NPH-22 105-011-10226 105-011-10235 G 1/2 172 121.5 11.5 NPH-27 105-011-10271 105-011-10280 174.5 124 12 NPH-34 105-011-10342 105-011-10351 G 3/4 179.5 125 13 NPH-43 105-011-10431 105-011-10441 185.5 130 13.5 NPH-51 105-011-10511 105-011-10520 190.5 130.5 14 G 3/4 NPH-61 105-011-10619 105-011-10628 G1 196.5 136.5 14.5 NPH-73 105-011-10735 105-011-10744 204.5 135.5 15 NPH-82 105-011-10824 105-011-10833 209.5 140.5 15.5 NPH-100 105-011-11001 105-011-11010 G1 1/4 226.5 154.5 15 G 1 G 3/4 NPH-125 105-011-11252 105-011-11261 242.5 158.5 17 04/08/2008

GEAR PUMPS NPH ISO GEAR PUMPS 105-011 TECHNICAL FEATURES Pump type Displacement Pressure Max. continuous speed P1 P2 P3 Max. intermittent speed Min. speed cm 3 /rev bar bar bar rpm rpm rpm NPH-17 NPH-22 17.04 22.15 290 315 325 2500 3000 NPH-27 26.18 NPH-34 33.88 280 300 310 2200 2800 NPH-43 43.12 270 290 300 NPH-51 50.82 240 260 280 2000 2500 NPH-61 60.06 220 240 250 1800 2000 NPH-73 72.88 200 220 230 1600 NPH-82 81.08 190 210 220 1800 NPH-100 98.18 180 200 1500 NPH-125 122.72 160 180 200 300 P1= Max. continuous pressure (100%) P2= Max. intermittent pressure (20 sec.max.) P3= Max. peak pressure (6 sec.max) DIRECTION OF ROTATION: Anti-clockwise rotation, left pump Clockwise rotation, right pump THE PUMP IS COMPLETE WITH DOUBLE OIL-SEAL AND TAPERED ROLLER BEARING ON THE OUTPUT SHAFT 04/08/2008

GEAR PUMPS NPGH UNI 3-BOLT Fluid Kinematic viscosity suggested Mineral or synthetic compatible with the following seals: NBR, FKM, FPM, Nylon Average ambient temp. ( C) < -10-10 10 10 35 > 35 VG (cst = mm 2 /s) 22 32 46 68 Optimale kinematic viscosity Max kinematic viscosity suggested at the start-up VG= 10 cst 100 cst VG= 750 cst Viscosity index suggested VI > 100 Oil filtering > 200 bar: 10 µm < 200 bar: 25 µm Inlet pressure Pump rotation -0,3 2 bar Unidirectional (Right or left) Pump type Rotation IN 1 IN 2 Right Left OUT 1 OUT 2 A B Weight ISO 228 ISO 228 mm mm kg NPGH-63 105-012-00638 105-012-00647 186 121 17.5 G 1 G 3/4 NPGH-73 105-012-00736 105-012-00745 190 125 18.5 NPGH-84 105-012-00843 105-012-00852 194 125.5 19 NPGH-100 105-012-01002 105-012-01011 G 1 1/4 200 129 19.5 NPGH-116 105-012-01164 105-012-01173 G 1 206 135 20 NPGH-133 105-012-01333 105-012-01342 216 137 21 G 1 1/2 NPGH-150 105-012-01502 105-012-01511 221 142 21.5 04/08/2008

GEAR PUMPS NPGH UNI GEAR PUMPS 105-012 TECHNICAL FEATURES Pump type Displacement Pressure Max. continuous speed P1 P2 P3 Max. intermittent speed Min. speed cm 3 /rev bar bar bar rpm rpm rpm NPGH-63 63.70 290 315 325 NPGH-73 74.87 280 300 315 NPGH-84 85.96 260 280 290 NPGH-100 102.60 250 270 280 NPGH-116 119.24 240 260 270 NPGH-133 135.88 220 250 260 NPGH-150 149.75 180 210 220 1800 1500 2700 2500 300 P1= Max. continuous pressure (100%) P2= Max. intermittent pressure (20 sec.max.) P3= Max. peak pressure (6 sec.max) TECHNICAL FEATURES Anti-clockwise rotation, left pump Clockwise rotation, right pump 04/08/2008

GEAR PUMPS NPGH ISO 4-BOLT Fluid Kinematic viscosity suggested Mineral or synthetic compatible with the following seals: NBR, FKM, FPM, Nylon Average ambient temp. ( C) < -10-10 10 10 35 > 35 VG (cst = mm 2 /s) 22 32 46 68 Optimale kinematic viscosity Max kinematic viscosity suggested at the start-up VG= 10 cst 100 cst VG= 750 cst Viscosity index suggested VI > 100 Oil filtering > 200 bar: 10 µm < 200 bar: 25 µm Inlet pressure Pump rotation -0,3 2 bar Unidirectional (Right or left) Pump type Rotation IN 1 IN 2 Right Left OUT 1 OUT 2 A B Weight ISO 228 ISO 228 mm mm Kg NPGH-63 105-012-10636 105-012-10645 201.5 136.5 19 G 1 G 3/4 NPGH-73 105-012-10734 105-012-10743 205.5 140.5 21 NPGH-84 105-012-10841 105-012-10850 209.5 141 21.5 NPGH-100 105-012-11000 105-012-11019 G 1 1/4 215.5 144.5 22 NPGH-116 105-012-11162 105-012-11171 G 1 221.5 150.5 22.5 NPGH-133 105-012-11331 105-012-11340 231.5 152.5 23.5 G 1 1/2 NPGH-150 105-012-11500 105-012-11519 236.5 157.5 24 04/08/2008

GEAR PUMPS NPGH ISO GEAR PUMPS 105-012 TECHNICAL FEATURES Pump type Displacement Pressure Max. continuous speed P1 P2 P3 Max. intermittent speed Min. speed cm 3 /rev bar bar bar rpm rpm rpm NPGH-63 63.70 290 315 325 NPGH-73 74.87 280 300 315 NPGH-84 85.96 260 280 290 NPGH-100 102.60 250 270 280 NPGH-116 119.24 240 260 270 NPGH-133 135.88 220 250 260 NPGH-150 149.75 180 210 220 1800 1500 2700 2500 300 P1= Max. continuous pressure (100%) P2= Max. intermittent pressure (20 sec.max.) P3= Max. peak pressure (6 sec.max) TECHNICAL FEATURES Anti-clockwise rotation, left pump Clockwise rotation, right pump THE PUMP IS COMPLETE WITH DOUBLE OIL-SEAL AND TAPERED ROLLER BEARING ON THE OUTPUT SHAFT 04/08/2008

PISTON PUMPS DARK UNI 3-BOLT Fluid Kinematic viscosity suggested Mineral or synthetic compatible with the following seals: NBR, FKM, FPM, Nylon Average ambient temp. ( C) < -10-10 10 10 35 > 35 VG (cst = mm 2 /s) 16 22 32 46 Optimale kinematic viscosity Max kinematic viscosity suggested at the start-up VG= 10 cst 100 cst VG= 750 cst Viscosity index suggested VI > 100 Oil filtering Inlet pressure Pump rotation > 200 bar: 10 μm < 200 bar: 25 μm 0,85 2 bar absolute Bidirectional Verify that pump is, at least, 100 mm under the minimum level of the tank. Before starting the pump bleed the air. t Pump type Code n c e m e Pressure Max speed Weight p a l s D i Max Peak cm 3 /rev bar bar rpm kg DARK-21 108-005-02111 20,25 DARK-28 108-005-02817 27 DARK-35 108-005-03512 33,75 DARK-42 108-005-04217 40,5 350 350 1800 13,5 DARK-48 108-005-04815 47,25 DARK-52 108-005-05216 51,97 DARK-55 108-005-05510 54 DARK-60 108-005-05912 59,3 300 350 1500 13,3 04/08/2008

PISTON PUMPS DARK ISO 4-BOLT Fluid Kinematic viscosity suggested Mineral or synthetic compatible with the following seals: NBR, FKM, FPM, Nylon Average ambient temp. ( C) < -10-10 10 10 35 > 35 VG (cst = mm 2 /s) 16 22 32 46 Optimale kinematic viscosity Max kinematic viscosity suggested at the start-up VG= 10 cst 100 cst VG= 750 cst Viscosity index suggested VI > 100 Oil filtering Inlet pressure Pump rotation > 200 bar: 10 μm < 200 bar: 25 μm 0,85 2 bar absolute Bidirectional Verify that pump is, at least, 100 mm under the minimum level of the tank. Before starting the pump bleed the air. t Pump type Code n c e m e Pressure Max speed Weight p a l s D i Max Peak cm 3 /rev bar bar rpm kg DARK-21 108-005-02120 20,25 DARK-28 108-005-02826 27 DARK-35 108-005-03521 33,75 DARK-42 108-005-04226 40,5 350 350 1800 14,1 DARK-48 108-005-04824 47,25 DARK-52 108-005-05225 51,97 DARK-55 108-005-05529 54 DARK-60 108-005-05921 59,3 300 350 1500 13,9 04/08/2008

PISTON PUMPS HDS ISO 4-BOLT Fluid Mineral or synthetic compatible with the following seals: HNBR Allowed temperature -40 +140 C Kinematic viscosity suggested Average ambient temp. ( C) < -40-40 10 10 35 > 35 VG (cst = mm 2 /s) 16 22 32 46 Optimale kinematic viscosity Max kinematic viscosity suggested at the start-up VG= 10 cst 100 cst VG= 750 cst Viscosity index suggested VI > 100 Oil filtering Inlet pressure Pump rotation > 200 bar: 10 µm < 200 bar: 25 µm 0,85 2 bar absolute Unidirectional (Right or Left) Verify that pump is, at least, 100 mm under the minimum level of the tank. Before starting the pump bleed the air. Dimensions in mm Pump type HDS-47 Rotation IN OUT Right Left ISO 228 ISO 228 108-015-04733 108-015-04742 G 1 1/4 G 3/4 HDS-55 HDS-64 108-015-05536 108-015-05545 108-015-06035 108-015-06044 G 1 1/2 G 3/4 G 1 1/2 G 3/4 04/08/2008

PISTON PUMPS 47-55-64 BENT AXIS PISTON PUMPS TECHNICAL FEATURES 108-015/915 108-016/916 108-907 Pump type Displacement Pressure Max. continuous speed Max. intermittent speed Min. speed Weight P1 P2 P3 cm 3 /rev bar bar bar rpm rpm rpm kg HDS-47 47,13 HDS-55 56,7 HDS-64 63,56 P1= Max. continuous pressure (100%) P2= Max. Intermittent pressure (20 sec.max.) P3= Max. peak pressure (6 sec.max) 350 370 400 1900 2500 300 12,6 FLOW DRIVE TORQUE Q (l/min) 200 180 160 140 120 100 80 60 40 20 MDS 80 HDS 64 HDS 55 HDS 47 Nm 500 450 400 350 300 250 200 150 100 50 MDS 80 HDS 64 HDS 55 HDS 47 500 1000 1500 2000 2500 rpm 5 0 100 150 200 250 300 350 400 bar kw 110 100 90 80 70 60 50 40 30 20 10 POWER INPUT 400 bar 350 bar 300 bar 250 bar 200 bar 150 bar 100 bar 50 100 150 200 Q (l/min) HOW TO CHOOSE THE SUCTION PIPE SIZE Flow Min pipe diam. Flow speed l/min mm inch (m/s) 20 25 1 0,68 30 32 0,62 1 1/4 40 32 0,83 50 38 0,74 1 1/2 60 38 0,88 70 40 1 9/16 0,93 80 45 0,84 1 3/4 90 45 0,94 100 50 0,85 2 110 50 0,93 120 60 0,71 130 60 0,77 2 3/8 140 60 0,83 150 60 0,88 160 63 0,86 170 63 2 1/2 0,91 180 63 0,96 To ensure the proper suction pipe size the flow speed should not exceed 1mt/sec. 04/08/2008

PISTON PUMPS HDS ISO 4-BOLT Fluid Mineral or synthetic compatible with the following seals: HNBR Allowed temperature -40 +140 C Kinematic viscosity suggested Average ambient temp. ( C) < -40-40 10 10 35 > 35 VG (cst = mm 2 /s) 16 22 32 46 Optimale kinematic viscosity Max kinematic viscosity suggested at the start-up VG= 10 cst 100 cst VG= 750 cst Viscosity index suggested VI > 100 Oil filtering Inlet pressure Pump rotation > 200 bar: 10 µm < 200 bar: 25 µm 0,85 2 bar absolute Unidirectional (Right or Left) Verify that pump is, at least, 100 mm under the minimum level of the tank. Before starting the pump bleed the air. Dimensions in mm Rotation IN OUT Pump type Right Left ISO 228 ISO 228 HDS-84 108-015-08033 108-015-08042 G 1 1/4 G 1 HDS-108 108-015-10833 108-015-10842 G 1 1/2 G 1 04/08/2008

PISTON PUMPS 84-108 BENT AXIS PISTON PUMPS TECHNICAL FEATURES 108-015/915 108-016/916 108-907 Pump type Displacement Pressure Max. continuous speed HDS-84 84,33 HDS-108 107 Max. intermittent speed Min. speed Weight P1 P2 P3 cm 3 /rev bar bar bar rpm rpm rpm kg 350 370 400 1500 2000 300 17,8 P1= Max. continuous pressure (100%) P2= Max. Intermittent pressure (20 sec.max.) P3= Max. peak pressure (6 sec.max) FLOW DRIVE TORQUE Q (l/min) 280 260 240 220 200 180 160 140 120 100 80 60 40 20 MDS 130 HDS 108 HDS 84 Nm 700 650 600 550 500 450 400 350 300 250 200 150 100 50 MDS 130 HDS 108 HDS 84 500 1000 1500 2000 2500 rpm 50 100 150 200 250 300 350 400 bar kw 110 100 90 80 70 60 50 40 30 20 10 POWER INPUT 400 bar 350 bar 300 bar 250 bar 200 bar 150 bar 100 bar 50 100 150 200 Q (l/min) HOW TO CHOOSE THE SUCTION PIPE SIZE Flow Min pipe diam. Flow speed l/min mm inch (m/s) 20 25 1 0,68 30 32 0,62 1 1/4 40 32 0,83 50 38 0,74 1 1/2 60 38 0,88 70 40 1 9/16 0,93 80 45 0,84 1 3/4 90 45 0,94 100 50 0,85 2 110 50 0,93 120 60 0,71 130 60 0,77 2 3/8 140 60 0,83 150 60 0,88 160 63 0,86 170 63 2 1/2 0,91 180 63 0,96 To ensure the proper suction pipe size the flow speed should not exceed 1mt/sec. 04/08/2008

HOISTS L02-L04-L06 SERIES Underbody m ax = 30 ØD E M10x1 L ±5 Z B A ±5 C ØH 40 I 40 G 1 /2 ØF Y X U V S W PIN S T U V W X Y Z T ØF mm 35 140 40 14 35.5 108 17 32 65 40 140 40 14 40.5 108 17 32 65 MODEL STAGES STROKE PIVOTS 48 CAPACITY VOLUME WEIGHT L A B C D E F H I mm mm tonne litres kg mm L02.237.3 4 510 630 3.9 1.5 13 337 145 192 73 120 58 40 95 120 L02.270.4 4 810 1000 2.7 1.9 18 350 155 195 100 85 45 35 95 115 LB04.4 4 820 1010 4.8 3.1 19 358 156 202 100 85 43 40 110 148 LC06.6 6 1000 1230 4.3 4.1 19 322 153 169 95 85 43 40 125 148 LB06.5 5 1030 1270 5.8 4.9 23 361 152 209 95 85 43 40 125 148 L06.5 5 1250 1540 5.8 6.0 28 406 152 254 95 85 43 40 125 148 L06.5Z 5 1440 1780 5.8 6.9 29 446 152 294 95 85 43 40 125 148 L06.450.4 4 1490 1840 7.3 8.3 35 547 156 391 83 120 58 40 125 148 L06.500.4 4 1690 2090 7.3 9.4 48 597 156 441 83 120 58 40 125 148 L06.575.4 4 1960 2420 7.3 11.0 55 672 155 517 82 120 58 40 125 148 L06.500.5 5 2120 2620 5.8 10.1 58 581 148 433 91 85 43 40 125 148 L06.575.5 5 2450 3020 5.8 11.8 61 656 148 508 91 85 43 40 125 148 All specifi cations subject to change without notice. Gough Transport Solutions accepts no responsibility for any losses incurred from any such changes, including those occuring as a result of fabrication conducted using dimensions shown. A hoist kit will not meet Australian Standard AS1418.8, nor Occupational Health and Safety rules without a Cylinder Blocking System or similar safety device. Maximum pressure 200 bar (2900 psi). Rated pressure 140 bar (2030 psi). Weights shown include brackets. 05/08/2008

HOISTS L08 SERIES Underbody m ax = 30 ØD E M10x1 L ±5 B A ±5 C ØH 40 I 40 (L08.583.5-3/4 ) G 1 /2 ØF Z Y U V S W X T PIN S T U V W X Y Z ØF mm 45 140 40 14 45.5 108 17 32 65 50 150 45 15 50.5 113 15 45 80 MODEL STAGES STROKE PIVOTS 48 CAPACITY VOLUME WEIGHT L A B C D E F H I mm mm tonne litres kg mm LB08.5 5 1160 1430 8.6 7.9 39 415 199 216 125 120 58 45 145 165 L08.5 5 1440 1780 8.6 9.8 40 475 199 276 125 120 58 45 145 165 LB08.6 6 1420 1750 6.9 8.5 32 404 183 221 125 85 43 45 145 165 L08.6 6 1730 2140 6.9 10.2 38 459 157 302 99 85 43 45 145 165 L08.510.5 5 2140 2640 8.6 17.3 66 615 162 453 88 120 58 45 145 165 L08.583.5 5 2480 3060 8.6 16.9 84 690 162 528 88 120 58 50 145 171 L08.583.6 6 2980 3680 6.9 17.7 tba 674 155 519 97 85 43 45 145 165 All specifi cations subject to change without notice. Gough Transport Solutions accepts no responsibility for any losses incurred from any such changes, including those occuring as a result of fabrication conducted using dimensions shown. A hoist kit will not meet Australian Standard AS1418.8, nor Occupational Health and Safety rules without a Cylinder Blocking System or similar safety device. Maximum pressure 200 bar (2900 psi). Rated pressure 140 bar (2030 psi). Weights shown include brackets. 05/08/2008

HOISTS S03-L03-L02 SERIES Underbody m ax = 30 ØD E PIN S T U V W X Y Z ØF mm 50 150 45 15 50.5 113 15 45 80 L ±5 B A ±5 C ØH 45 45 I ±2 G Ø50 1/2 - L03B.7 & L02B.8 3/4 - SM03.6 & L02.584.6S M10x1 X Y Z U V S ØF T W MODEL STAGES STROKE PIVOTS 48 CAPACITY VOLUME WEIGHT L A B C D E F H I mm mm tonne litres kg mm SM03.6 6 1750 2160 14 19 72 533 254 279 138 150 73 210 177 216 L03B.7 7 1580 1950 11 15 61 419 154 265 145 120 58 210 177 216 L02.584.6S 6 2930 3620 22 44 114 689 245 444 162 150 73 230 198 238 L02B.8 8 1820 2250 13 21 77 424 219 205 145 120 58 230 198 238 All specifi cations subject to change without notice. Gough Transport Solutions accepts no responsibility for any losses incurred from any such changes, including those occuring as a result of fabrication conducted using dimensions shown. A hoist kit will not meet Australian Standard AS1418.8, nor Occupational Health and Safety rules without a Cylinder Blocking System or similar safety device. Maximum pressure 200 bar (2900 psi). Rated pressure 140 bar (2030 psi). Weights shown include brackets. 05/08/2008

HOISTS L02-L06-L08 SO SERIES Underbody ØD ØF E PIN S T U V W X Y Z ØF mm 40 140 40 14 40.5 108 17 32 65 45 140 40 14 45.5 108 17 32 65 L ±5 A ±5 C ØH M10x1 B X Y Z G 1 /2 U V S T W 40 40 I ±2 MODEL STAGES STROKE CAPACITY VOLUME WEIGHT L A B C D E F H I mm tonne litres kg mm L02.370.2SO 2 600 5.0 2.2 20 469 418 30 365 55 31 40 95 125 L02.470.2SO 2 800 5.0 3.3 26 566 515 30 470 55 31 40 95 125 L02.355.3SO 3 850 3.9 2.5 19 454 403 30 350 40 26 40 95 125 L06.460.3SO 3 1140 8.9 7.4 34 545 490 30 454 55 31 40 125 158 L06.575.3SO 3 1470 8.9 9.5 58 677 623 30 569 55 31 40 125 158 L06.4ZSO 4 1140 7.3 6.3 30 464 413 30 359 55 31 40 125 158 L06.400.4SO 4 1280 7.3 7.1 34 485 434 30 395 55 31 40 125 158 L06.450.4SO 4 1480 7.3 8.2 33 549 498 30 444 55 31 40 125 158 L06.500.4SO 4 1680 7.3 9.3 48 588 537 30 494 55 31 40 125 158 L08.528.5SO 5 2240 8.6 15.2 58 643 568 40 521 55 31 45 145 178 All specifi cations subject to change without notice. Gough Transport Solutions accepts no responsibility for any losses incurred from any such changes, including those occuring as a result of fabrication conducted using dimensions shown. A hoist kit will not meet Australian Standard AS1418.8, nor Occupational Health and Safety rules without a Cylinder Blocking System or similar safety device. Maximum pressure 200 bar (2900 psi). Rated pressure 140 bar (2030 psi). Weights shown include brackets. 05/08/2008

HOISTS L02 SERIES Trailer underbody 1/2 BSP 55 95.4 25.5 25.5 A MODEL STAGES STROKE CAPACITY VOLUME WEIGHT A mm tonne litres kg mm L02.835.2OO 2 1378 5 5.7 28 915 L02.935.2OO 2 1578 5 6.6 32 1015 Suggested layout only L02.835.2OO L02.935.2OO B 250 292 C 880 1005 D 75 75 E 1890 2170 mm F 200 200 J 3660 4880 K 1750 2010 L 380 425 All specifi cations subject to change without notice. Gough Transport Solutions accepts no responsibility for any losses incurred from any such changes, including those occuring as a result of fabrication conducted using dimensions shown. A hoist kit will not meet Australian Standard AS1418.8, nor Occupational Health and Safety rules without a Cylinder Blocking System or similar safety device. Maximum pressure 240 bar (3500 psi) Rated pressure 175 bar (2500 psi) 13/08/2010

HOISTS FLC75-90 SERIES Front mount 50 Heavy-duty application FLC75 = Ø133 FLC90 = Ø160 Superior stage overlap Chromed top stage L ±5 A 40 FLC75 = 184 ±2 40 FLC90 = 208 ±2 178 90 204 B ±5 318 1/2 BSPP Ø17 35 150 95 110 FLC75 = 125 FLC90 = 150 FLC75 = 175 FLC90 = 200 FLC75 = 225 FLC90 = 250 MODEL STAGES STROKE PIVOTS CAPACITY VOLUME WEIGHT A B L mm 48 mm tonne litres kg mm FLC3.75.2500 3 2507 3100 8 7 98 787 213 1085 FLC3.75.2950 3 2942 3650 8 9 109 932 213 1230 FLC3.90.2850 3 2858 3520 12 13 110 894 163 1142 FLC3.90.3550 3 3562 4400 12 16 132 1015 343 1443 All specifi cations subject to change without notice. Gough Transport Solutions accepts no responsibility for any losses incurred from any such changes, including those occuring as a result of fabrication conducted using dimensions shown. A hoist kit will not meet Australian Standard AS1418.8, nor Occupational Health and Safety rules without a Cylinder Blocking System or similar safety device. Maximum pressure 220 bar (3190 psi) Rated pressure 140 bar (2030 psi) Weights shown include brackets 05/08/2008

HOISTS FLC105 SERIES Front mount 50 Heavy-duty application Superior stage overlap Ø178 Chromed top stage A 40 230 ±2 40 178 90 B ±5 204 318 L ±5 3/4 BSPP Ø17 40 150 95 110 170 220 270 MODEL STAGES STROKE PIVOTS CAPACITY VOLUME WEIGHT A B L mm 48 mm tonne litres kg mm FLC3.105.3150 3 3153 3900 18 20 133 914 343 1297 FLC4.105.3750 4 3758 4650 15 21 136 767 343 1200 FLC4.105.4250 4 4226 5200 15 24 146 893 343 1326 FLC4.105.4750 4 4747 5850 15 27 160 1023 343 1456 All specifi cations subject to change without notice. Gough Transport Solutions accepts no responsibility for any losses incurred from any such changes, including those occuring as a result of fabrication conducted using dimensions shown. A hoist kit will not meet Australian Standard AS1418.8, nor Occupational Health and Safety rules without a Cylinder Blocking System or similar safety device. Maximum pressure 200 bar (2900 psi) Rated pressure 140 bar (2030 psi) Weights shown include brackets 27/09/2010

HOISTS PFC116-135 SERIES Front mount PFC116 = Ø185 PFC135 = Ø200 Heavy-duty application Superior stage overlap Chromed top stage A 46 PFC116 = 230 ±2 46 PFC135 = 245 ±2 178 90 204 318 B ±5 L ±5 13 1 BSPP 294 244 194 30 150 95 Ø17 110 MODEL STAGES STROKE PIVOTS CAPACITY VOLUME WEIGHT A B L mm 48 mm tonne litres kg mm PFC3.116.3815 3 3815 4700 21 29 219 1242 340 1612 PFC4.116.4509 4 4509 5550 17 32 197 1116 333 1479 PFC4.116.5101 4 5101 6300 17 33 227 1249 340 1619 PFC3.135.3192 3 3192 3950 30 35 203 1049 340 1419 PFC3.135.3446 3 3446 4250 30 37 222 1116 366 1512 PFC3.135.3792 3 3792 4700 30 41 231 1242 340 1612 PFC4.135.4478 4 4478 5550 25 42 212 1101 340 1471 PFC4.135.5070 4 5070 6250 25 47 245 1249 340 1619 PFC5.135.5616 5 5616 6950 20 45 216 1093 355 1478 All specifi cations subject to change without notice. Gough Transport Solutions accepts no responsibility for any losses incurred from any such changes, including those occuring as a result of fabrication conducted using dimensions shown. A hoist kit will not meet Australian Standard AS1418.8, nor Occupational Health and Safety rules without a Cylinder Blocking System or similar safety device. Maximum pressure 200 bar (2900 psi) Rated pressure 140 bar (2030 psi) Weights shown include brackets 05/08/2008

HOISTS PFC154-174 SERIES Front mount PFC154 = Ø230 PFC174 = Ø250 Heavy-duty application Superior stage overlap Chromed top stage L ±5 A 46 PFC154 = 310 ±2 46 PFC174 = 325 ±2 229 B ±5 32 102 159 216 45 102 19 1 BSPP 215 165 Ø20 PFC154 = 35 PFC174 = 45 110 236 296 356 MODEL STAGES STROKE PIVOTS CAPACITY VOLUME WEIGHT A B L mm 48 mm tonne litres kg mm PFC5.154.6313 5 6313 7800 29 70 354 1255 340 1630 PFC4.174.7156 4 7156 8800 46 120 481 1817 340 2202 PFC5.174.8126 5 8126 9990 39 121 495 1622 340 2007 All specifi cations subject to change without notice. Gough Transport Solutions accepts no responsibility for any losses incurred from any such changes, including those occuring as a result of fabrication conducted using dimensions shown. A hoist kit will not meet Australian Standard AS1418.8, nor Occupational Health and Safety rules without a Cylinder Blocking System or similar safety device. Maximum pressure 200 bar (2900 psi) Rated pressure 140 bar (2030 psi) Weights shown include brackets 22/12/2008

HOISTS M03 SERIES Well mount Low profile construction Ideal for tarping applications Light weight Chromed top stage 140 106 Ø177 Ø13. 5 106 140 55 L ± 5 Ø50 1 BSPP O/A ± 5 Bolt pattern 165 x 275 Ø20 230 ±2 320 ±2 MODEL STAGES STROKE PIVOTS CAPACITY VOLUME WEIGHT L O/A mm 48 mm tonne litres kg mm M03.670.5SS 5 2781 3450 29 34 113 756 866 M03.750.5SS 5 3181 3950 29 39 124 836 946 All specifi cations subject to change without notice. Gough Transport Solutions accepts no responsibility for any losses incurred from any such changes, including those occuring as a result of fabrication conducted using dimensions shown. A hoist kit will not meet Australian Standard AS1418.8, nor Occupational Health and Safety rules without a Cylinder Blocking System or similar safety device. Maximum pressure 185 bar (2700 psi) Rated pressure 140 bar (2030 psi) Weights shown include brackets 05/08/2008

HOISTS PF135 LP SERIES Well mount 146 100 70 Ø16 178 Ø157 O/A ±5 A ±5 1 BSPP 294 240 194 Ø57 E 150 95 Ø17 110 57 Heavy-duty application Low profile construction Chromed top stage MODEL STAGES STROKE PIVOTS CAPACITY VOLUME WEIGHT A E O/A mm 48 mm tonne litres kg mm PF3.135.2670 3 2671 3300 30 31 135 1103 69 1270 PF3.135.2870 3 2866 3550 30 33 143 1168 69 1335 PF3.135.3170 3 3166 3900 30 36 151 1268 69 1435 PF3.135.3440 3 3436 4250 30 37 170 1324 69 1491 PF3.135.3440MT 3 3436 4250 30 37 170 1118 257 1285 PF3.135.3440HT 3 3436 4250 30 37 170 tba tba tba PF3.135.3830HT 3 3826 4750 30 41 179 1250 257 1417 PF3.135.4010HT 3 4006 4950 30 43 184 1303 264 1470 All specifi cations subject to change without notice. Gough Transport Solutions accepts no responsibility for any losses incurred from any such changes, including those occuring as a result of fabrication conducted using dimensions shown. A hoist kit will not meet Australian Standard AS1418.8, nor Occupational Health and Safety rules without a Cylinder Blocking System or similar safety device. Maximum pressure 200 bar (2900 psi) Rated pressure 140 bar (2030 psi) Weights shown include brackets 02/03/2009

HOISTS PF135 SERIES Well mount 146 100 70 Ø16 180 Ø159 A ±5 1 BSPP 294 240 194 E 150 95 Ø17 110 Ø57 76 Heavy-duty application O/A ±5 Superior stage overlap Chromed top stage MODEL STAGES STROKE PIVOTS CAPACITY VOLUME WEIGHT A E O/A mm 48 mm tonne litres kg mm PF4.135.3250 4 3250 4000 25 30 127 1109 35 1295 PF4.135.3869 4 3869 4800 25 36 144 1292 30 1478 PF4.135.4478 4 4478 5550 25 42 164 1469 30 1655 PF4.135.4478HT 4 4478 5550 25 42 164 1119 380 1305 All specifi cations subject to change without notice. Gough Transport Solutions accepts no responsibility for any losses incurred from any such changes, including those occuring as a result of fabrication conducted using dimensions shown. A hoist kit will not meet Australian Standard AS1418.8, nor Occupational Health and Safety rules without a Cylinder Blocking System or similar safety device. Maximum pressure 200 bar (2900 psi) Rated pressure 140 bar (2030 psi) Weights shown include brackets 05/08/2008

HOISTS PF154 LP SERIES Well mount 146 100 70 Ø16 178 Ø177 A ±5 1 BSPP 356 296 236 E Ø57 215 165 Ø20 110 57 Heavy-duty application Low profile construction O/A ±5 Chromed top stage MODEL STAGES STROKE PIVOTS CAPACITY VOLUME WEIGHT A E O/A mm 48 mm tonne litres kg mm PF4.154.4570 4 4565 5650 34 60 220 1371 65 1538 PF4.154.5090 4 5085 6300 34 67 237 1501 65 1668 PF4.154.5590 4 5585 6900 34 74 252 1626 65 1793 PF4.154.5890 4 5885 7300 34 78 262 1708 65 1875 All specifi cations subject to change without notice. Gough Transport Solutions accepts no responsibility for any losses incurred from any such changes, including those occuring as a result of fabrication conducted using dimensions shown. A hoist kit will not meet Australian Standard AS1418.8, nor Occupational Health and Safety rules without a Cylinder Blocking System or similar safety device. Maximum pressure 200 bar (2900 psi) Rated pressure 140 bar (2030 psi) Weights shown include brackets 05/08/2008

HOISTS PF174 SERIES Well mount 160 170 90 Ø20 210 Ø203 A ±5 1 BSPP 356 296 236 E Ø57 215 165 Ø20 110 75 Heavy-duty application Superior stage overlap O/A ±5 Chromed top stage MODEL STAGES STROKE PIVOTS CAPACITY VOLUME WEIGHT A E O/A mm 48 mm tonne litres kg mm PF4.174.5364 4 5364 6600 46 90 306 1704 45 1889 PF4.174.6227 4 6227 7700 46 105 320 1902 45 2087 PF4.174.7156 4 7156 8850 46 121 371 2179 45 2364 PF5.174.5697 5 5697 7050 39 85 288 1563 45 1748 PF5.174.6145 5 6145 7600 39 92 300 1547 45 1732 PF5.174.6276 5 6276 7750 39 94 306 1614 45 1799 PF5.174.7191 5 7191 8900 39 107 341 1777 90 1962 All specifi cations subject to change without notice. Gough Transport Solutions accepts no responsibility for any losses incurred from any such changes, including those occuring as a result of fabrication conducted using dimensions shown. A hoist kit will not meet Australian Standard AS1418.8, nor Occupational Health and Safety rules without a Cylinder Blocking System or similar safety device. Maximum pressure 200 bar (2900 psi) Rated pressure 140 bar (2030 psi) Weights shown include brackets 22/12/2008

HOISTS PF196 SERIES Well mount 160 170 90 Ø20 210 Ø229 A ±5 1 BSPP * PFL models side ported 414 339 Ø63.5 264 E 215 165 Ø20 125 75 Heavy-duty application O/A ±5 Superior stage overlap Chromed top stage MODEL STAGES STROKE PIVOTS CAPACITY VOLUME WEIGHT A E O/A mm 48 mm tonne litres kg mm PF4.196.5706 4 5706 7050 60 131 388 1785 55 1985 PF4.196.5706MT 4 5706 7050 60 131 388 1662 178 1862 PF4.196.6253 4 6253 7700 60 144 391 1862 90 2062 PF4.196.6454 4 6454 7950 60 149 424 1972 55 2172 PF4.196.6454MT 4 6454 7950 60 149 424 1849 178 2049 PF4.196.7126 4 7126 8800 60 164 439 2162 55 2362 PF5.196.5661 5 5661 7000 52 117 375 1504 55 1704 PF5.196.6236 5 6236 7700 52 121 377 1612 55 1812 PFL5.196.6430* 5 6430 7950 52 126 384 1539 85 1764 PF5.196.6686 5 6686 8250 52 130 391 1709 55 1909 PF5.196.7036 5 7036 8700 52 137 401 1779 55 1979 PF5.196.7580 5 7580 9350 52 150 430 1907 55 2107 All specifi cations subject to change without notice. Gough Transport Solutions accepts no responsibility for any losses incurred from any such changes, including those occuring as a result of fabrication conducted using dimensions shown. A hoist kit will not meet Australian Standard AS1418.8, nor Occupational Health and Safety rules without a Cylinder Blocking System or similar safety device. Maximum pressure 185 bar (2670 psi) Rated pressure 140 bar (2030 psi) Weights shown include brackets 04/09/2008

CYLINDER BLOCKING SYSTEM CBS Safety valve The revolutionary and patented Cylinder Blocking System (CBS) is a dedicated safety device, designed and manufactured by a hoist manufacturer, to operate in conjunction with tipping hoists. It offers unparalleled protection for personnel from the dangers of falling tipper bodies. Hose failures are a reality, capable of causing serious injury or even death. In the event of a sudden drop in system pressure, CBS will prevent tipping hoist closure, protecting vehicles and operator alike from the dangers of a violently dropping body. Australian Standard AS1418.8 requires that a tip truck be fi tted with a safety device to protect against the effects of failure of a hose in any support circuit on a hoisting system. CBS satisfi es workplace safety requirements simply, reliability and effectively. 04/08/2010

CYLINDER BLOCKING SYSTEM CBS OPERATION The CBS system is compact, quickly and easily installed, and can be fi tted directly onto the hoist port with the body in position. Its automatic function is indiscernible to the operator and is fail safe. The valve does not rely on sensing a hose failure, but rather must be operational in order for the hoist to lower. Typical layout shown for tipper system with air operated control valve. Solutions and instructions are available for all control valve types and applications. Part No Description Port size 8E12*VEC CBS VALVE FOR SMALL TIPPERS ELECTRICALLY OPERATED 1/2 BSPP 8E12MC*V CBS VALVE FOR SMALL TIPPERS PNEUMATICALLY OPERATED 1/2 BSPP 8E1EC*V CBS VALVE FOR LARGE TIPPERS ELECTRICALLY OPERATED 1 BSPP 8E1MC*V CBS VALVE FOR LARGE TIPPERS PNEUMATICALLY OPERATED 1 BSPP 8E1ECS*V CBS VALVE FOR SEMI TIPPERS (not shown) 1 BSPP * 12 = 12V DC 24 = 24V DC 04/08/2010

SAFETIP Tipper Rollover Warning System Don t let this happen to you!

SAFETIP How SAFETIP works SAFETIP continuously monitors a tipper s horizontal condition and alerts the operator when the lateral angle exceeds a programmed safe tipping range. If warnings are ignored, SAFETIP prevents the trailer from tipping further until it is again within the safe tipping range. SAFETIP is: TIPPING ENABLED TIPPING DISENABLED A fraction of the cost of damage caused by a rollover and could attract a discount on insurance premiums Quick and easy to install either at time of manufacture or to an existing tipper Effective in all tipper applications ie. rigid, dog trailer and semi tipper - both chassis type and tip-over-axle Fully programable so that warning angles can be set to suit specific operating conditions Status display TYPICAL INSTALLATION Control module Sensor unit Trailer socket/plug Power supply PTO engaged signal Trailer applications only Air control Solenoid valve Raise line Lower line Tipper valve