4.3" Color TFT Display

4.3" Color TFT Display FEATURES Type: TFT Diagonal dimension: 4.3" Display format: 480 x 272 (RGB) Built-in controller: SSD1963 +5 V power supply Material categorization: For definitions of compliance please see www.vishay.com/doc?99912 MECHANICAL DATA ITEM DIMENSION UNIT Dot matrix 480 x 272, RGB (TFT) dots Module dimension 106.7 x 83.98 x 7.1 mm Active area 95.04 x 53.86 mm Dot pitch 0.066 x 0.198 mm LCD type TFT, negative transmissive View direction 12 o clock Gray scale inversion direction 6 o clock Backlight type LED, normally white Controller IC SSD1963 Interface Digital 8080 family MPU Note Color tone changed by temperature and driving voltage ABSOLUTE MAXIMUM RATINGS ITEM Operating temperature Storage temperature SYMBOL STANDARD VALUE MIN. TYP. MAX. UNIT T OP -20 - +70 C T ST -30 - +80 C Note Device is subject to be damaged permanently if stressed beyond those absolute maximum ratings listed above ELECTRICAL CHARACTERISTICS ITEM SYMBOL CONDITION STANDARD VALUE MIN. TYP. MAX. UNIT Supply voltage for LCM V DD - 3.0 3.3 3.6 V Supply current for LCM I VDD V DD = 3.3 V, T a = 25 C - 200 300 ma Operating current for LED driver (1)(2) I OP VLED+ = 3.3 V - 270 405 ma Power consumption (1)(2) P C VLED+ = 3.3 V - 891 1337 mw Supply voltage for LED driver (1)(2) V CC VLED+ - 3.3 5 V LED life time (2)(3)(4) t - - 50 000 - h Notes (1) Power supply the backlight IC specification (2) T a = 25 C (3) Brightness to be decreased to 50 % of the initial value (4) The single LED lamp case Revision: 13-Dec-13 1 Document Number: 37489

INTERFACE PIN FUNCTION PIN NO. SYMBOL I/O/P FUNCTION 1 GND P System ground pin of the IC, connect to system ground 2 V DD P Power supply: +3.3 V 3 BL_E I Backlight control signal, H: On/L: Off 4 D/C I Data/command select 5 WR I Write strobe signal 6 RD I Read strobe signal 7 DB0 I Data bus 8 DB1 I Data bus 9 DB2 I Data bus 10 DB3 I Data bus 11 DB4 I Data bus 12 DB5 I Data bus 13 DB6 I Data bus 14 DB7 I Data bus 15 DB8 I Data bus 16 DB9 I Data bus 17 DB10 I Data bus 18 DB11 I Data bus 19 DB12 I Data bus 20 DB13 I Data bus 21 DB14 I Data bus 22 DB15 I Data bus 23 NC - No connection 24 NC - No connection 25 CS I Chip select 26 RESET I Hardware reset 27 DIP ON I Display control, H: On/L: Off 28 NC - No connection 29 NC - No connection 30 NC - No connection 31 NC - No connection 32 NC - No connection 33 VLED- I VLED- for B/L, LED inverter (ground) 34 VLED- I VLED- for B/L, LED inverter (ground) 35 VLED+ I VLED+ for B/L, LED inverter (+3.3 V) 36 VLED+ I VLED+ for B/L, LED inverter (+3.3 V) Revision: 13-Dec-13 2 Document Number: 37489

1.Module Classification Information LC F 43 Q T I B E D B N 0 H 1 2 3 4 5 6 7 8 9 10 11 12 13 Brand Intertechnology, Inc. Display Type N Character Type, H Graphic Type F TFT Type Display Size 4.3 TFT Model serials no.: Q Backlight Type F CCFL, White T LED, White LCD Polarize Type/ Temperature range/ Gray Scale Inversion Direction I Transmissive, W. T, 6:00 L Transmissive, W.T,12:00 A TFT LCD B TFT+FR+CONTROL BOARD C TFT+FR+A/D BOARD D TFT+FR+A/D BOARD+CONTROL BOARD E TFT+FR+POWER BOARD F TFT+CONTROL BOARD 9 10 G TFT+FR H TFT+D/V BOARD I TFT+FR+D/V BOARD J TFT+POWER BD Resolution: A: 128160 B:320234 C:320240 D:480234 E:480272 F: 640480 G: 800480 H:1024600 I:320480 J:240320 K:800600 L:240400 M :1024768 D: Digital L LVDS Interface N without control board A 8Bit B 16Bit 11 TS N Without TS T resistive touch panel C capacitive touch panel 12 Version: 0 13 Special Code H: Compliant with ROHS directive regulations Revision: 13-Dec-13 3 Document Number: 37489

2.SUMMARY This technical specification applies to 4.3 color TFT-LCD panel. The 4.3 color TFT-LCD panel is designed for camcorder, digital camera application and other electronic products which require high quality flat panel displays. This module follows RoHS. 3.General Specification Item Dimension Unit Dot Matrix 480 x RGBx272(TFT) dots Module dimension 106.7 x 83.98 x 7.1 mm Active area 95.04 x 53.86 mm Dot pitch 0.066 x 0.198 mm LCD type TFT, Negative, Transmissive View Direction 12 o clock Gray Scale Inversion Direction 6 o clock Backlight Type LED, Normally White Controller IC SSD1963 Interface Digital 8080 family MPU *Color tone slight changed by temperature and driving voltage. Revision: 13-Dec-13 4 Document Number: 37489

4.Absolute Maximum Ratings Item Symbol Min Typ Max Unit Operating Temperature T OP -20 +70 Storage Temperature T ST -30 +80 Note: Device is subject to be damaged permanently if stresses beyond those absolute maximum ratings listed above 1. Temp. 60 0 C, 90% RH MAX. Temp. 60 0 C, Absolute humidity shall be less than 90% RH at 60 0 C Alloeable Forward Current IF(mA) Ambient Tem. vs Alloeable Forward Curren 40 30 20 10 0 0 20 40 60 80 100 Ambient Temperature(oC) Revision: 13-Dec-13 5 Document Number: 37489

5.Electrical Characteristics 5.1. Operating conditions: Item Symbol Condition Min Typ Max Unit Supply Voltage For LCM VDD 3.0 3.3 3.6 V Supply Current For LCM IVDD VDD=3.3V, Ta = 25-200 300 ma 5.2 Backlight driving conditions Parameter Symbol Min. Typ. Max. Unit Remark Operation Current For LED Driver VLED+=3.3V - 270 405 ma Note 1,2 Power Consumption VLED+=3.3V - 891 1337 mw Note 1,2 Supply Voltage For LED Driver VLED+ - 3.3 5 V Note 1,2 LED Life Time - 50,000 - Hr Note 2,3,4 Note 1 : Power supply the back light IC specification Note 2 : Ta = 25 Note 3 : Brightness to be decreased to 50% of the initial value Note 4 : The single LED lamp case 6. DC Characteristics Parameter Symbol Rating Min Typ Max Unit Condition Low level input voltage VIL 0-0.3VDD V High level input voltage VIH 0.7VDD - VDD V 7. Interface Timing 7.1.1 8080 Mode The 8080 mode MCU interface consist of CS#, D/C#, RD#, WR#, D[15:0] and TE signals. This interface use WR# to define a write cycle and RD# for read cycle. If the WR# goes low when the CS# signal is low, the data or command will be latched into the system at the rising edge of WR#. Similarly, the read cycle will start when RD# goes low and end at the rising edge of RD#. Revision: 13-Dec-13 6 Document Number: 37489

7.1.2 8080 Mode Write Cycle Symbol Parameter Min Typ Max Unit fmclk System Clock Frequency 1-110 MHz tmclk System Clock Period 1/ fmclk - - ns tpwcsh tpwcsl Control Pulse High Width Write Read Control Pulse Low Width Write (next write cycle) Write (next read cycle) Read 13 30 13 80 80 1.5* tmclk 3.5* tmclk - 1.5* tmclk 9* tmclk 9* tmclk 7.1.2.1 Parallel 8080-series Interface Timing Diagram(Write Cycle) ns - ns tas Address Setup Time 1 - - ns tah Address Hold Time 2 - - ns tdsw Write Data Setup Time 4 ns tdhw Write Data Hold Time 1 - - ns tpwlw Write Low Time 12 ns tdhr Read Data Hold Time 1 - - ns tacc Access Time 32 ns tpwlr Read Low Time 36 - - ns tr Rise Time - 0.5 ns tf Fall Time - - 0.5 ns tcs Chip select setup time 2 - ns tcsh Chip select hold time to read signal 3 - - ns Revision: 13-Dec-13 7 Document Number: 37489

7.1.2.2 Parallel 8080-series Interface Timing Diagram(Read Cycle) 7.1.3 Pixel Data Format Revision: 13-Dec-13 8 Document Number: 37489

8. Optical Characteristics Item Symbol Condition. Min Typ. Max. Unit Remark Tr - 10 20 ms Response time =0 =0 Note 3,5 Tf - 15 30 ms At optimized Contrast ratio CR 400 500 - - Note 4,5 viewing angle Wx 0.24 0.29 0.34 Color Chromaticity White =0 =0 Note 2,6,7 Wy 0.26 0.31 0.36 R 60 70 - Hor. L 60 70 - Viewing angle CR 10 Deg. Note 1 T 40 50 - Ver. B 60 70 - Center of Brightness - - 350 420 - cd/m 2 display Ta=25±, IL=20mA Note 1: Definition of viewing angle range Fig. 8-1 Definition of viewing angle Note 2: Test equipment setup: After stabilizing and leaving the panel alone at a driven temperature for 10 minutes, the measurement should be executed. Measurement should be executed in a stable, windless, and dark room. Optical specifications are measured by Topcon BM-7 or BM-5 luminance meter 1.0 field of view at a distance of 50cm and normal direction. Fig. 8-2 Optical measurement system setup Revision: 13-Dec-13 9 Document Number: 37489

Note 3: Definition of Response time: The response time is defined as the LCD optical switching time interval between White state and Black state. Rise time, Tr, is the time between photo detector output intensity changed from 90%to 10%. And fall time, Tf, is the time between photo detector output intensity changed from 10%to 90% Display Data 100% 90% W hite(tft OFF) Black(TFT ON) W hite(tft OFF) 10% 0% Note 4: Definition of contrast ratio: The contrast ratio is defined as the following expression. Contrast ratio (CR) = Luminance measured when LCD on the "White" state Luminance measured when LCD on the "Black" state Note 5: White Vi = Vi50 ± 1.5V Black Vi = Vi50 ± 2.0V ± means that the analog input signal swings in phase with VCOM signal. ± means that the analog input signal swings out of phase with VCOM signal. The 100% transmission is defined as the transmission of LCD panel when all the input terminals of module are electrically opened. Note 6: Definition of color chromaticity (CIE 1931) Color coordinates measured at the center point of LCD Note 7: Measured at the center area of the panel when all the input terminals of LCD panel are electrically opened. Revision: 13-Dec-13 10 Document Number: 37489

9. Interface 9.1. LCM PIN Definition Pin Symbol I/O Function Remark 1 GND P System round pin of the IC. Connect to system ground. 2 VDD P Power Supply : +3.3V 3 BL_E I Backlight control signal, H: On \ L: Off 4 D/C I Data/Command select 5 WR I Write strobe signal 6 RD I Read strobe signal 7 D0 I Data bus 8 D1 I Data bus 9 D2 I Data bus 10 D3 I Data bus 11 D4 I Data bus 12 D5 I Data bus 13 D6 I Data bus 14 D7 I Data bus 15 D8 I Data bus 16 D9 I Data bus 17 D10 I Data bus 18 D11 I Data bus 19 D12 I Data bus 20 D13 I Data bus 21 D14 I Data bus 22 D15 I Data bus 23 NC - No connection 24 NC - No connection 25 CS I Chip select 26 RESET I Hardware reset 27 DIP ON I Display control H: On \ L:Off 28 NC - No connection 29 NC - No connection 30 NC - No connection 31 NC - No connection 32 NC - No connection 33 VLED- I VLED- for B/L LED inverter (GND) 34 VLED- I VLED- for B/L LED inverter (GND) 35 VLED+ I VLED+ for B/L LED inverter (+3.3V) 36 VLED+ I VLED+ for B/L LED inverter (+3.3V) Revision: 13-Dec-13 11 Document Number: 37489

10. BLOCK DIAGRAM BL TFT LCD 480xRGBx272 FPC inferface VDD GND D/C WR RD CS RS BL_E RESET DB0 DB15 VCC GND VSYNC HSYNC DISP DCLK DE R7~R0 G7~G0 B7~B0 X1 Y1 X2 Y2 LED- LED+ RESET SSD1963 Control Board DIS_ON VLED- VLED+ Revision: 13-Dec-13 12 Document Number: 37489

11.Reliability Content of Reliability Test (Wide temperature, -20 ~70 ) Environmental Test Test Item Content of Test Test Condition Note High Temperature Endurance test applying the high storage 80 2 storage temperature for a long time. 200hrs Low Temperature Endurance test applying the high storage -30 1,2 storage temperature for a long time. 200hrs High Temperature Endurance test applying the electric stress 70 Operation (Voltage & Current) and the thermal stress to the 200hrs element for a long time. Low Temperature Endurance test applying the electric stress under -20 1 Operation low temperature for a long time. 200hrs High Temperature/ The module should be allowed to stand at 60 60,90%RH 1,2 Humidity Operation,90%RH max 96hrs For 96hrs under no-load condition excluding the polarizer, Then taking it out and drying it at normal temperature. Thermal shock The sample should be allowed stand the -20 /70 resistance following 10 cycles of operation 10 cycles -20 25 70 Vibration test 30min 5min 30min 1 cycle Endurance test applying the vibration during Total fixed transportation and using. amplitude : 15mm Vibration Frequency : 10~55Hz One cycle 60 seconds to 3 directions of X,Y,Z for Each 15 minutes Static electricity test Endurance test applying the electric stress to the terminal. VS=800V, RS=1.5k CS=100pF 1 time Note1: No dew condensation to be observed. Note2: The function test shall be conducted after 4 hours storage at the normal Temperature and humidity after remove from the test chamber. Note3: Vibration test will be conducted to the product itself without putting it in a container. 3 Revision: 13-Dec-13 13 Document Number: 37489

12.Contour Drawing 4-? 3.5 P T H RGB 1 GND 2 VDD 3 BL_E 4 D/C 5 WR 6 RD 7 DB0 8 DB1 9 DB2 10 DB3 11 DB4 12 DB5 13 DB6 14 DB7 15 DB8 16 DB9 17 DB10 18 DB11 19 DB12 20 DB13 21 DB14 22 DB15 23 NC 24 NC 25 CS 26 RESET 27 DISP_ON 28 NC 29 NC 30 NC 31 NC 32 NC 33 VLED- 34 VLED- 35 VLED+ 36 VLED+ 1 Lcd Type 2 TFT 6 O'clock The non-specified tolerance of dimension is Ó0.3mm. 3 Polsrizer Mode TRANSMISSIVE 4 screen size 4.3(diagonal) 5 display format 480 RGB X 272 6 Operating Temperature -20 XC ~70 XC 7 Storage Temperature -30 XC ~80 XC 8 Active area 95.04(W) X 53.856(H) mm 9 dot pitch 0.066(W) X 0.198(H) mm 10 Color arrangement RGB-STRIPE Revision: 13-Dec-13 14 Document Number: 37489

13. Initial Code For Reference void Initial_code() { Write_Command(0x01); Delay_ms(10); Write_Command(0xe0); Write_Parameter(0x01); Delay_ms(50; Write_Command(0xe0); Write_Parameter(0x03); Delay_ms(5); Write_Command(0xb0); Write_Parameter(0x20); Write_Parameter(0x80); Write_Parameter(0x01); Write_Parameter(0xdf); Write_Parameter(0x01); Write_Parameter(0x0f); Write_Command(0xf0); Write_Parameter(0x03); //0x03 is 16bit(565 format);0x00 is for 8-bit,pixel data format //Set the MN of PLL Write_Command(0xe2); Write_Parameter(0x1d); Write_Parameter(0x02); Write_Parameter(0x54); Write_Command(0xe6); Write_Parameter(0x01); Write_Parameter(0x99); Write_Parameter(0x9a); //Set front porch and back porch Write_Command(0xb4); Write_Parameter(0x02); Write_Parameter(0x0d); Write_Parameter(0x14); Write_Parameter(0x05); Write_Command(0xb6); Write_Parameter(0x01); Write_Parameter(0x24); Write_Parameter(0x0a); Write_Parameter(0x05); Revision: 13-Dec-13 15 Document Number: 37489

Write_Command(0x2a); Write_Parameter(0x01); Write_Parameter(0xdf); Write_Command(0x2b); Write_Parameter(0x01); Write_Parameter(0x0f); } Write_Command(0x29); Write_Command(0x2c); Revision: 13-Dec-13 16 Document Number: 37489

Legal Disclaimer Notice Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, ), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on s knowledge of typical requirements that are often placed on products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer s technical experts. Product specifications do not expand or otherwise modify s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the product could result in personal injury or death. Customers using or selling products not expressly indicated for use in such applications do so at their own risk. Please contact authorized personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of. Product names and markings noted herein may be trademarks of their respective owners. Revision: 13-Jun-16 1 Document Number: 91000