My home Mobile phone application For DELTA DORE GSM transmitters and transmitter control units Instructions for use and installation My home Alarm Heating Bedroom Dining room Kitchen Garage Absence Messages Option
Contents 1 - Presentation............................................................... 3 2 - Downloading the application.................................................4 Via your mobile phone............................................................ 4 Via a PC.......................................................................... 4 Using the application with an Android smartphone.................................4 3 - First connection........................................................... 5 Launching the application.........................................................5 Saving the number of the control unit or the transmitter.............................5 Saving the mobile phone number..................................................5 Uploading your configuration......................................................5 4 - Controlling your installation.................................................. 6 Presentation......................................................................6 Operation.........................................................................6 Checking the status of the installation..............................................7 Quitting the application............................................................7 5 - Managing messages....................................................... 8 Reading messages................................................................8 Deleting a message...............................................................8 Emptying the mailbox.............................................................8 6 - Customising your application................................................ 9 Renaming the Channel icons.................................................... 9 Creating a scenario............................................................... 9 Using a scenario.................................................................. 9 Modifying a scenario............................................................ 10 Renaming a scenario............................................................ 10 Deleting a scenario.............................................................. 10 7 - Customising the system.................................................... 11 Changing the system date...................................................... 11 Changing the call numbers....................................................... 11.............................................................. 11 Activating a control system control channel...................................... 12 Deactivating a control system control channel.................................... 12 Activating the heating control.................................................... 13 Deactivating the heating control.................................................. 13 8 - Protecting the application.................................................. 14 Activating the access code...................................................... 14 Changing the session duration................................................... 14 Deactivating the access code.................................................... 14 9 - Advanced functions....................................................... 15 Displaying the system parameters............................................... 15 Acknowledgement of commands................................................. 15 2
1- Presentation The My home mobile phone application allows you to: access your installation remotely to check its status, control your installation remotely (create scenarios, information feedback with certain products, consult documentation, etc.), receive event messages sent by the transmitter. My home 22 : 44 Alarm Heating Bedroom This application can be installed on a compatible mobile phone. It communicates with your transmitter using SMS. To find out about compatibility and to install the application on your mobile phone, go to the website: http://www.deltadore.com/mobile 10:20 Dining room Kitchen Garage Absence Messages Mobile phone 22 : 44 JAVA application 10:20 SMS Transmitter Alarm detector Alarm detector Control systems: lighting, roller shutters, gate... Control systems: garage door... Heating and domestic hot water control 3
2- Downloading the application Via your mobile phone (recommended) To download the My home application using your mobile (Blackberry or other JAVA compatible phones), you must connect to the Internet using a data connection. The data connections on your phone (WAP, GPRS, EDGE or 3G) must be configured (ask your operator). Via a PC You can download the My home application to your PC at the following address: http://www.deltadore.com/mobile - choose the most appropriate application for the screen resolution of your mobile phone. - download the application - when the download is complete: connect your mobile to the computer, transfer the application to your mobile and install. To download the application: 1- using an Android smartphone: - from your device, press the Android Market icon - search for My home delta dore - download the application 2- using a JAVA compatible phone: - open the web browser on your mobile phone and go to the following address: http://www.deltadore.com/wap - choose the most appropriate application for the screen resolution of your mobile phone. - download the application Important: several security messages may pop up during download. Simply confirm to continue installation. Note : for more information about installing an application via a PC, please refer to your mobile phone instructions. Do not use the PC download method for Android smartphones. Using the application with an Android smartphone Function not selected Press and release Selects the required status The My home JAVA application screens and control may display differently depending on the model of the mobile phone you are using. (refer to your mobile phone documentation) Important: the application uses SMS messages to exchange information with the system. There will therefore be a delay of a few seconds each time a message is sent. In exceptional cases, an SMS message may fail to reach its destination. Press and hold Access to the available modifications Access to the help section > 2 sec JAVA, JME and all JAVA-based marks are trademarks or registered trademarks of Sun Microsystems, Inc. in the U.S. and/or other countries. Android and Android Market are registered trademarks of Google Inc. BlackBerry is a registered trademark of Research In Motion Ltd in the U.S. and/or other countries. 4
3- First connection Launching the application When opening the application for the first time, the features of the phone are tested and you should see the 3 icons shown here. If your phone is not adapted, an error message is displayed: - Incompatible screen size, please download... (download the application again), - Incompatible character size (some text may not display correctly but the application will still work), - Incompatible (your phone does not have the necessary features - you cannot use the application to control your installation). My home Messages Info Save the number of the control unit or the transmitter Before sending a command to the system, you should save the number of the telephone line to which the alarm system is connected. On your mobile: - select the icon, - select, - enter the number of the telephone line, - confirm your selection. Important: This number will remain saved in your phone, it may be modified. : 06 01 02 03 04 Saving the mobile phone number For security reasons, you must save the number of the mobile phone which has the My home application, in the Change the call numbers menu of your alarm control unit or your transmitter. (Refer to the corresponding documentation) Uploading your configuration The My home JAVA application adapts to your configuration based on the products associated with your system: To upload your configuration: - select the Info icon, - select send, - once the configuration request is received, the control unit or the transmitter sends a message to your mobile. - select view to display your configuration in the general menu. Info View Send Reception of the new configuration Alarm Heating Bedroom Living room Water Garage 5. Messages Info Example
4- Controlling your installation Presentation The My home application is designed to control your home installation: Switch alarm surveillance: Adjust the heating level using the following icons: Alarm on off Heating Frost Protection Economy Comfort Automatic Water Control domestic hot water via an energy manager. Off Automatic Chan 1* Control a control system (lighting, roller shutters, etc.) On Off Timed operation 0000 0000 * The name of this icon can be changed. (see Customising your application ) Android smartphones 1 2 3 4 5 6 7 8 0 9 > 2 sec. Note: you can find a description of each feature by selecting the Help menu. Operation - in the My home application, select the icon of the command you wish to modify, - press the confirm button repeatedly to select the desired status, - follow the same procedure for each of the commands you wish to modify (hot water, heating, alarm, etc.), to put a control system channel in timed operation mode, 01:35 - select the icon of the required command (e.g.: dining room), - press repeatedly to display the Timer icon 00:00, - press the timer icon (press and hold for Android smartphones, select the configure menu), - enter the duration. (e.g.: 0135 for 1 hour 35 minutes), - select Send, - confirm that you wish to send the message, - the mobile phone sends the command to the system. Alarm Heating Bedroom Dining room Water Garage. Messages Info Alarm Heating Bedroom Dining room Water Garage. Messages Info Send 6
Checking the status of the installation To view the following information: - alarm surveillance ON or OFF, - most recent event, - the faults (battery, open entry, etc.), - inside temperature (near the transmitter control unit or transmitter) and outdoor temperature (for outdoor siren only), - hot water on or off, - heating status. You need to: - select the Info icon, - select Send and confirm. - To view the SMS sent in reply, check the Messages received box. Info Send Important: it is not possible to check the On/Off status of your control systems. Quitting the application To quit the My home application: - select Close and confirm. 7
5- Managing messages The Messages received and Messages sent boxes may contain up to 10 messages each. The messages are sorted by date. If the maximum number of messages is reached, the most recent message received/sent replaces the oldest. Unread messages are displayed in red. Messages received: - acknowledgement (see Acknowledgement of commands ), - info (status of alarm, heating, hot water, temperature), - param. info (call numbers, batteries, software version), - error (command to activate alarm surveillance while it is in maintenance mode). Messages sent: - cmd (commands sent), - info (request for information). Messages Received Sent Received at Subj 10/05/10 12:11 Info 05/05/10 15:54 Info 08/04/10 09:12 Param Info. 22/03/10 05:23 Param Info. Received Sent Issued at Subj 15/05/10 20:05 Info 14/05/10 12:00 Info Reading messages To read your messages: - select the Messages icon, - select Received or Sent by pressing right or left, - select a message by pressing up or down, - confirm to see the content of the message. 2/4 Received on 05/05/10 at 15:54 System date: 05/05/10 15:54 Intruder alarm on 03/05/10 at 16:36 Bedroom 3 Battery fault Open entry Deleting a message To delete a message: - select the Messages icon, - select Received or Sent by pressing right or left, - select the message to be deleted by pressing up or down, - select Delete, - the message disappears. Received Sent Issued at Subj 15/05/10 20:05 Info 14/05/10 12:00 Info Delete Emptying the mailbox To delete all Received or Sent messages: - select the Messages icon, - select Received or Sent by pressing right or left, - select Empty, - all messages are deleted Received Sent Issued at Subj 15/05/10 20:05 Info 14/05/10 12:00 Info Empty Received Sent Issued at Subj 8
6- Customising your application Renaming the Channel icons To rename: - select the icon of the channel you wish to rename, - select Rename, - enter the new name (e.g. Shutters), - confirm, - the icon name is modified. Rename Chan 1 Shutters Creating a scenario To make it easier to send several commands that need to be changed frequently. To create a scenario: - select the status of the commands you wish to modify (alarm, heating, channel 1, etc.), - select Save, - enter the name of the scenario (e.g. Absence), - confirm, - the scenario icon appears on the screen Alarm Heating Bedroom Dining room Water Garage Save Scenario name: Absence. Messages Info Alarm Heating Bedroom Dining room Kitchen Garage Absence. Messages Using a scenario - select the relevant scenario icon, - confirm to activate it, - the different commands are displayed, - select Send, - confirm that you wish to send the message, - the mobile phone sends the command to the system. Absence Absence Send 9
6- Customising your application Modifying a scenario* To modify the commands of an existing scenario: - select the relevant scenario icon, - confirm to activate it, - modify the desired commands, - go back to the scenario icon, - select Modify, - the scenario is modified. Absence Absence modify the desired commands Modify * not available on Android smartphone Absence Renaming a scenario To rename a scenario: - select the relevant scenario icon, - select Rename, - rename the scenario, - confirm, - the scenario name is modified. Absence Rename Start Deleting a scenario To delete a scenario: - select the relevant scenario icon, - select Delete, - confirm, - the scenario is deleted. Absence Delete 10
7- Customising the system Important: all these settings can be adjusted using voice synthesis (except ). If you have already created your settings, you do not need to modify them using the My home application. Changing the system date To set the date and time of the transmitter: - select ->, - by default, the phone time and date are displayed, ready to be sent, - enter the date and time, - select Send and confirm. enter the date and time Changing the call numbers To change the call numbers to be used by the transmitter in the event of an alarm: - select ->, - enter or change the call numbers, - select Send and confirm. To delete a number, just leave the corresponding field empty. Call number 1: 02 12 34 56 78 Call number 2: 02 12 34 56 89 Call number 3: 02 12 34 56 90 Call number 4: For each call number stored in the transmitter, you can select the type of message that will be sent in the event of an alarm (voice synthesis or SMS): - select ->, - for each number, choose By voice or By SMS, - select Send, then confirm to send the message to the system. If you have changed the mailing list options using another mobile phone, you must retrieve the mailing list information beforehand: - select ->, - select Request and confirm, - upon reception of the system s response, go back to the menu to modify the initial settings. if a message is sent via SMS, it will go directly into the phone s mailbox rather than the one in the Ma Maison application. : Call no. 1 By voice By SMS Call no. 2 By voice By SMS Call no. 3 By voice By SMS Call no. 4 By voice By SMS 11
7- Customising the system Activating a control system control channel The system has four control channels for control systems. Each of these channels can be associated with the diverse functions of receivers from the control systems range. Example: channel 1 can be used to raise/lower the roller shutters. On the receiver, The procedure is similar for associating any button on a receiver with a system control channel. put the receiver in association mode (refer to the corresponding documentation) In the mobile phone application: - select ->, - choose the control system channel to be assigned (e.g. chan 1), - select Associate, then confirm to send the message. After a few seconds, the system emits one beep. Make sure that the buttons on the receiver are no longer flashing. The buttons are now associated with control channel 1 on the system. Put the receiver in association mode (refer to the corresponding documentation) Heating Chan 1 Chan 2 Chan 3 Chan 4 Important: the first time a product is associated with a control system channel, the icon will appear in the My home application once the next system message is received (see Checking the status of the installation ). Associate Deactivating a control system control channel In the mobile phone application: - select ->, - choose the control system channel to be deactivated (e.g. chan 2), - select Delete, then confirm to send the message, - after a few seconds, the system emits one beep. Control channel 2 is no longer enabled on the system. In the application, the channel 2 icon will disappear the next time a message from the system is received. Heating Chan 1 Chan 2 Chan 3 Chan 4 Delete 12
Activating the heating control Put the heating control in association mode (refer to the corresponding documentation) In the My home application: - select ->, - choose the Heating channel, - select Associate, then confirm to send the message. Note: if you order a CALYBOX, the Hot water icon will appear. This will allow you to switch the domestic hot water on and off. Put the heating control in association mode (refer to the corresponding documentation) Heating Chan 1 Chan 2 Chan 3 Chan 4 Associate Deactivating the heating control In the mobile phone application: - select ->, - choose the Heating channel, - select Delete, then confirm to send the message. In the application, the heating icon will disappear the next time a message from the system is received. Heating Chan 1 Chan 2 Chan 3 Chan 4 Delete 13
8- Protecting the application Activating the access code You can set an access code to protect the My home application. By default, this code is not activated. To create or modify the access code: - select -> -> Access code - enter the code (4 to 8 digits), - confirm the code, - select OK and confirm, - the access code is confirmed. It will be requested each time the application is opened. By default, it will only be valid for a limited period of 5 minutes (session duration). Important: if you forget your access code, you must remove the My home application from your phone and download it again. All settings will be lost. New access code (4 to 8 digits): ******* Confirm the new access code: ******* OK Access code Session duration Changing the session duration To modify the access code validity period, you must modify the session duration. To require the code for every alarm surveillance on/off command, select Alarm security. To modify or deactivate the session duration: - select -> -> Session duration, - enter the access code, - change the duration (e.g. 15 min.), - select OK and confirm. At the end of the session, you will need to re-enter the access code when you restart the My home application or when sending a message to the system. Access code: ******* 5 mn 10 mn 15 mn Alarm security Deactivate Access code Session duration Deactivating the access code To deactivate the access code: - select -> -> Session duration, - enter the access code, - select Deactivate, - select OK and confirm. Access code: ******* 5 mn 10 mn 15 mn Alarm security Deactivate 14
9 - Advanced functions Displaying the system parameters - the system date and time, - the call numbers, - the battery voltages, - the system software version. To receive this information: - select ->, - confirm to send the message. Send After a few seconds, the application will receive a message from the system. To read the information: - select Messages -> Received, - select the most recent message. Messages Received Sent Received at Subj 10/05/10 12:11 Info 05/05/10 15:54 Info 08/04/10 09:12 Param Info. 22/03/10 05:23 Param Info. 2/4 Received on 10/05/10 at 12:11 System date: 10/05/10 12:11 Call no. 1: 0612345678 Call no. 2: 0612345679 Call no. 3: 0612345680 Signal level: strong (24) Battery voltage 5.5 V Software version: V1.02 Acknowledgement of commands You can request the system to send you an acknowledgement for each message sent: - select. ->, - select Yes, - select OK, then confirm to save the change. The next time a command is sent to the system, you will receive an acknowledgement. To read the acknowledgement messages: - select Messages -> Received, - select the most recent message. If you select No, you will not be sent any acknowledgement messages. Receive acknowledgements OK Yes No 15
www.deltadore.com Delta Dore hereby declares that the equipment complies with the essential requirements and other relevant provisions of the R&TTE Directive 1999/5/EC (radio) *2703336_rev1* Due to changes in standards and equipment, the characteristics given in the text and the illustrations of this document are not binding unless confirmed by our services.