Main catalogue Terminal Blocks entrelec. Explosive Atmospheres Protection

Main catalogue Terminal Blocks entrelec Explosive tmospheres Protection

T0700 Terminal Blocks entrelec : The best in connection Introducing the new TEX certified terminal block range The following pages are meant to provide you with some basic information relative to the TEX directive and protection methods particularly suitable for terminal blocks. We insist on the increased demand for safety required by the TEX directive and describe what has been the design and manufacturing choice of BB to provide you with true security products. s one of the world leaders in connection technology, BB is pleased to introduce you to its dedicated terminal block range for safe use in explosive atmospheres. The range is certified to the highest possible certification level of the new TEX 94/9/EC European directive and offers maximized safety to offer you true security products. Safe use and pplications Comprehensive range The TEX terminal block range provides terminal blocks in the three main technologies: screw clamp, spring clamp and DO system in feed through (grey), neutral (blue) and ground versions. BB TEX terminal block range is available in V0 (per UL94) material. s we are constantly extending our product portfolios, please do not hesitate to contact your local sales if you would like to request an TEX certified terminal block not mentioned in these pages. BB s dedicated TEX range is designed and certified for use in all industries with potentially explosive atmospheres caused by gas or dust inflammation such as: petrochemical industries, off shores installations, mines industries, flour mills, silos etc

T0700 tex generalities Contents. Explosive atmosphere... 2 B. European explosion directives... 4 C. TEX 94/9/EC conformity assessment procedures... 8 D. Protection methods in potentially explosive atmosphere... 0 E. entrelec terminal blocks & accessories certifications... 2 TEX certified terminal blocks range Summary... 3

T0700. Explosive atmosphere Conditions n explosion can occur if the following factors are combined: Presence of inflammable substances Presence of an ignition source or inflammation source: fire, flame, electrical or mechanical sparks, overheated surfaces, electrostatic discharges Oxygen Inflammable substances can be listed as follow: Inflammable gas Inflammable liquid Inflammable dust Liquid gas: butane, butene, propane, propylene Smoke: carbon monoxide, methane Chemical gas substances : acetylene, acetylene oxide, vinyl chloride Solvents Fuel Oil Heating oil Painting Chemical substances Coal Wood dust Human and animal food : sugar, flour, cereal... Plastic material Metal Ignition source: Electrical energy may be dangerous if used close to an inflammable substance as it is considered as a potential source of ignition. Indeed, sparks, arcs or dangerous temperature levels are generated by the electrical energy. Protection: Particular methods of protection have thus been investigated in order to allow the use of electrical equipment in hazardous areas. Concerned industries The risk of explosion is particularly high in certain types of industries, which generate inflammable gas, inflammable liquid or inflammable dust. Indeed, the new TEX directive now considers the explosion risk caused by dust. We can list: Refineries, Petrochemical and chemical industries, Off shore installations, Mining industries, Human and food industries

T0700. Explosive atmosphere (cont.) The risk can be expressed as follow: Industries Refineries Petrochemical and chemical industries Pharmaceutical and cosmetic industries Waste and water recycling industries Painting facilities Gas distribution Human and animal food industries Wood saw mills, metal machining Risks Treatment of hydrocarbon highly inflammable Transformation and treatment processes which can generate explosive mixing Use of alcohol highly inflammable like solvents Use of active material or adjuvant which can create explosive dust Paper or plastic dust Storage of barrels or containers partially or not emptied Gas fermentation emission during water treatment Over spray formation during the lacquering of surfaces with spray gun Transport and stocking of cereal, powder which can create potentially dust explosive atmospheres in filters and aerators Metal dust generation during metal polishing which can create dust explosive atmospheres in collectors Génération de poussières métalliques lors du polissage des métaux qui peuvent créer une atmosphère explosible dans les collecteurs 3

T0700 B. European explosion directives TEX European directive consists in two parts : TEX 94/9/EC (generally called TEX 95), which concentrates on the duties of the manufacturers. TEX 999/92/EC (generally called TEX 37), which focuses on the end users obligations. * Directive applicable to entrelec terminal blocks The objectives of the directives "Minimum requirements" is a key phrase of the directives - member states are free to introduce more stringent measures if they wish. TEX belongs to the group of the so-called "new approach" directives. Under a new approach directive, any route towards achieving the objective is permitted. The European commission will not interfere with how a technical solution is reached, but gives all parties involved the freedom to define the best means, methods and procedures to meet the guidelines. This gives rise to a division of responsibilities between the equipment manufacturer and the end user. The less responsibility the equipment manufacturer assumes for achieving the solution, the more the end user will have to take on, and vice versa. 4

T0700 B. European explosion directives (cont.) TEX 95: Equipments and components The objective of the TEX 95 directive is to reinforce safety aspects. It is more restricting than the former directive 76/7 EEC, as it does not only concentrate on the product but on the whole process. The manufacturer s quality assurance is now audited through the relevant standard NF EN 3980 Potentially explosive atmospheres - pplication of quality systems. Extract of the EN 3980 7.5.3: The manufacturer shall establish and maintain procedures for product identification during all the stages of production, testing, final inspection and placing on the market. Traceability is required with respect to final product and its significant parts. The "production quality assurance notification" is the highest assurance quality certification level achievable. TEX products are considered as safety devices: the entire process from the design to the installation must be strictly controlled. Product and company quality assessment which allow design, manufacturing and sales. Requirements in terms of organization for designing, manufacturing and selling. BB commitments versus TEX 95 Terminal blocks are unitary controlled - unitary dielectric control on finished product Maximized security is guaranteed through dedicated manufacturing processes, dedicated manufacturing sites and dedicated inventory locations. Reinforced traceability for accurate identification of the TEX customers through dedicated part numbers for the TEX range and batch number registration. TEX 37: Installations The addition of the new "workers directive TEX 37" reinforces the safety level even further. Risk analysis: requires that the employers draw up evidence of risk analysis for their site. rea classification: area classification into zones and site inspections must be carried out where potentially explosive atmospheres may develop. Explosion protection document: Information such as written instructions, training programs, and clearance for work must be defined in the "explosion" protection document" and respected in order to guarantee the protection of the staff. TEX certified products must be selected according to zone. Locations where explosive atmospheres may occur and identified through warning signs. BB commitments versus TEX 37 Reliable product information is given to the end user: increased safety and intrinsic safety certified terminal blocks for safe installation. Excellence of DO system in regards to the TEX 37 minimum requirements (training programs, written instructions, clearance for work ): - Simplified "clearance for work": no possibility of unauthorized modifications thanks to the DO system dedicated tool (OUMD, OUPD or OUTD). - Maximized "correct installation and operation, qualification of the personnel": the DO system connection is operator independent. - No retightening maintenance: DO system is a Screwless technology. Dates of enforcement TEX 95: Equipment and components From July st 2003, equipment, protection systems and electrical components used in potentially explosive atmospheres must comply with the European directive TEX 94/9/EC (TEX 95). TEX 95 abrogates the directive 76/7/EC and becomes mandatory for all new equipment installed after 06/30/03. Former Ex products, already in stock, can still be installed if they are to replace used parts in already active installations. Dates of enforcement TEX 37: Installations The TEX 999/92/EC (TEX 37) directive becomes mandatory for all new installations implemented after 06/30/03, in every country member of the EEC. For existing installations, three more years are given to fulfill the minimum requirements. If an old work place is upgraded, modified or extended, it must comply with the "minimum requirements" immediately. 5

T0700 B. European explosion directives (cont.) Definitions and terms Equipment and components used in potentially explosive atmospheres are divided into groups and categories. (tex 94/9/EC, chapter, art, 3c) This classification is meant to define clearly the "intended use" of equipment, protective systems and devices, which is considered of prime importance for safe operation. Groups Two distinct groups according to the industry type in which the equipments or components are to be used: Group I stands for Mine industries: Underground part of mines and surface installations of such mines, liable to be endangered by firedamp and / or combustible dust. Group II stands for Surface industries: ll other places liable to be endangered by explosive atmospheres. Categories TEX defines "categories of equipment", specified by their protection characteristics: For Mine industries: - Category M : very high level of safety - Category M 2: high level of safety For surfaces industries: - Category : very high level of safety - Category 2: high level of safety - Category 3: normal level of safety? Frequently asked question: If equipment is certified in category, is it certified in category 2? Equipment or components certified in category are also certified in category 2 and category 3 since category is the highest level of safety. 6

T0700 B. European explosion directives (cont.) Equipment in category: M (Mine industries) Is required to remain functional, even in the event of rare incidents relating to equipment, with an explosive atmosphere present. M2 (Mine industries) Is intended to be de-energized in the event of an explosive atmosphere. The means of protection relating to equipment in this category assure the requisite level of protection during normal operation and also in the case of more severe operating conditions, in particular those arising from rough handling and changing environmental conditions. (Surface industries) Must ensure the requisite level of protection, even in the event of rare incidents relating to equipment and is characterized by means of protection such that: - Either, in the event of failure of on means of protection, at least an independent second means provides the requisite level of protection. - Or the requisite level of protection is assured in the event of two faults occurring independently of each other. 2 (Surface industries) Must ensure the requisite level of protection, even in the event of frequently occurring disturbances or equipment faults which normally have to be taken into account. 3 (Surface industries) Ensure the requisite level of protection during normal operation. Intended use: In underground parts of mines as well as those parts of surface installations of such mines endangered by firedamp and/or combustible dust. In underground parts of mines as well as those parts of surface installations of such mines endangered by firedamp and/or combustible dust. Zone 0 and Zone 20: reas in which explosive atmospheres caused by mixtures of air and gases, vapors or mists or by air/dust mixtures are present continuously, for long periods or frequently. Zone and Zone 2: reas in which explosive atmospheres caused by mixtures of air and gases, vapors or mists or by air/dust mixtures are likely to occur. Zone 2 and Zone 22: reas in which explosive atmospheres caused by gases, vapors or mists or by air/dust mixtures are unlikely to occur or are likely to do so only infrequently and for a short period only. tex 94/9/EC annex I 0 and 20 zones and 2 zones and 22 zones Explosive atmospheres classification example 7

T0700 C. TEX 94/9/EC conformity assessment procedures The TEX certification process can be identified as two main parts: The EC type examination certificate confirms that the validity of the technical file established by BB is in conformity with the tex directive. Examination and test results of the product are been examined by a notified body. The inspection of quality assurance, conducted by a notified body: refers to the production or product quality assurance examination (depending upon the product level of certification). The notification has three years validity with yearly audit. s said in chapter B, TEX directives objective is to increase the safety. Therefore, a quality assurance audit is now necessary to obtain the TEX certification for any equipment or component. Complete conformity assessment procedure is detailed here below: tex 94/9/EC chapter II, article 8 BB certification conformity "Production Quality Insurance" inspection "EC type examination certificate" Notified bodies "Notified Bodies", are independant bodies which are appointed by the Member States. They have the relevant expertise and facilities to undertake the required procedures such as : " Examination", which involves an assessment made of the product against the Essential Health and Safety Requirements of the Directive. Report of the manufacturer's Quality ssurance procedures to ensure that the "type" will continue to comply with the requirements. These "Notified Bodies" are given a number and are listed in the OJEC by the European Commission prior to their operation; the activities of the Notified Bodies are a matter for Member States, as they are appointed under their authority. While the Notified Body has various responsibilities under the Directive, the manufacturer always remains responsible for the compliance of the equipment. 8

T0700 C. TEX 94/9/EC conformity assessment procedures. (cont.) Production quality assessment notification Extract list of European Notified bodies and Certified bodies: Country Name Notified Bodies (TEX 94/4/EC) Certified Bodies (Ex) Denmark DEMKO X X France Germany INERIS LCIE* X X PTB X X TÜV Italy CESI X X Netherland KEM X Norwaye NEMKO Sweden SP X X UK SIR X X X *LCIE: identification code 008 Subsidiary of Bureau Veritas group EC type examination certificate 9

T0700 D. Protection methods in potentially explosive atmosphere Protection methods are to be implemented so that equipment and electrical components can be used in a potentially explosive atmosphere. Safety methods: Protection types Ex d: flame-proof Ex e: increased Ex i: intrinsic Ex m, Ex o, Ex p or Ex q Principles Contains the explosion in an appropriate explosion proof housing. Increases the reliability of the electrical components so that sparks or arcs cannot appear. Ex e voltage to apply is determined through severe limitations in the calculations of clearance and creepage distances. Reduces the energy to a very low energy level so that even sparks or arcs cannot ignite an explosion atmosphere. Prevent contact between the electrical component and the explosive atmosphere pplications for Ex d, Ex e and Ex i protection types Flameproof protection Ex d mong the several protection methods, flameproof "Ex d" protection method is the most ancient and therefore represents the protection method the most implemented. Non-TEX certified terminal blocks could be installed in a flameproof enclosure: the protection against explosion propagation is ensured by the enclosure not by the terminal block itself. However, as it requires a very specific design (the enclosure must be capable of withstanding a possible internal explosion), this solution appears over costly for terminal block installations. Intrinsic protection Ex i Intrinsic protection is a common method of protection for instrumentation and control; it applies to an entire circuit. Blue is generally the colour code for the intrinsic circuit components. It is the only protection method that can be implemented in zone 0 or 20 (permanent presence of explosive atmosphere), as the allowed voltage and current are extremely low. Voltage and current calculations are necessary to ensure that the circuit composed of its several components will operate safely. Increased protection Ex e Increased protection remains the best economical and technical choice for a safe use of terminal blocks in hazardous locations. BB TEX terminal block range, certified in increased safety, requires a high level of construction technology and do not require an explosion proof (Ex d) enclosure to operate safely in an explosive atmosphere. Please note that the enclosure containing the terminal blocks must offer a Dust protection (IP6X minimum) and be Ex e certified itself in order to determine the maximum surface temperature in the housing (calculations consider the number of terminal blocks in the housing and current to be applied) BB supplies intrinsic and increased protection certified terminal blocks, even if the intrinsic certification is not mandatory for components. The reasons are added benefits for our customers: it allows us to supply you with the TEX appropriate group and category marked on the block as well as the Ex i necessary voltage calculations, which have been confirmed by a notified body. 0

T0700 D. Protection methods in potentially explosive atmosphere (cont.) Terminal blocks use Here below are the protection methods, for which the TEX certification applies to terminal blocks. (*certification is not mandatory for components used in intrinsic protection only) Normes EN Méthodes de protection Symbole Concepts EN 60079-0 General rules EN 60079-7 Increased safety e No sparks or arcs in normal use. Control of dangerous temperature levels : because they can generate arcs or sparks in normal use, switch or fuse terminal blocks cannot be classified in increased protection. EN 50020 Intrinsic safety i Control of sparks, arcs or overheating through a very low energy level

T0700 E. Entrelec terminal blocks & accessories certification TEX Terminal block range certification level Ex e IM2 and II2GD and Ex i IM and IIGD The BB attestation of conformity guarantees the end user the conformity of the product in regards with the TEX 95 directive and applicable standards. It is generic to the whole TEX range. ccessory certification Entrelec terminal block accessories are automatically TEX certified. Please refer to the catalogue pages for the accessory list per terminal block. Some accessories like jumper bars or shielding connectors may declass the terminal block voltage. The detailed voltage is not indicated in the EC type examination certificate -the examination certificate, issued by the notified body, is meant to establish the TEX terminal block conformity only-. Technical instruction sheets are at your disposal with all data for the appropriate voltage values as well as the operation and maintenance instructions. Please request them from your local sales. example of terminal blocks technical instruction sheet 2

T0700 TEX certified Terminal blocks range Contents Screw clamp connection DIN - 3 Standard and ground terminal blocks... 4 Double-deck terminal blocks... 7 Three level sensor terminal blocks... 8 Safety connection terminal blocks... 9 Thermocouple terminal blocks... 20 Power terminal blocks... 2 Screw clamp terminal blocks DIN 2... 24 Spring clamp DIN 3 Standard and ground terminal blocks... 25 Spring clamp miniblocks DIN 2 and base mount... 29 DO - Screw clamp DIN 3 Standard and ground terminal blocks... 30 Double-deck terminal blocks... 32 DO - DO connection DIN 3 Standard and ground terminal blocks... 33 Double-deck terminal blocks... 35 Screw clamp - DO connection miniblocks DIN 2-3 and base mount... 36 DO - DO connection miniblocks DIN 2-3... 38 Index... 39 3

T07074 Standard and ground Terminal blocks M 2,5/5...Ex Spacing 5 mm.200" M 4/6...Ex Spacing 6 mm.238" M 4/6.3...Ex Spacing 6 mm.238" Screw clamp DIN -3 Exe and Exi voltage ratings apply to terminal blocks only without any accessory and mounted on DIN 3 rail. The use of ground terminal blocks do not decrease the standard terminal block's voltage ratings. For the terminal block voltage rating with its accessories, consult our "TEX technical instructions sheet for safe mounting". Standard 5 mm block M 2,5/5.P.Ex Spacing 5 mm.200" Standard 6 mm block M 4/6.P.Ex Spacing 6 mm.238" Standard 6 mm block One circuit and three clamps M 4/6.4...Ex Spacing 6 mm.238" End stop th. 9 mm BDL V0 End stop th. 9, mm BM2 V0 Rail 35 x 7,5 x PR3.Z2 Rail 35 x 5 x 2,3 PR4 Rail 35 x 5 x,5 PR5 Rail 32 x 5 x,5 PR.Z2 Standard blocks UL 94 V0 Terminal blocks for ground wires UL 94 V0 Wire size Short circuit current (for ground blocks) / s Wire stripping length Recommended torque Nm / Ib.in Voltage EN 60079-7 ; EN 50020 TEX marking TEX certificate ccessories 2 4 3 SN 399 903 R0200 SN 296 35 R0000 SN 74 300 R700 SN 68 500 R200 SN 68 700 R2200 SN 63 050 R0400 M 2,5/5.Ex Blue body M 2,5/5.N.Ex Green body Yellow body Green/yellow body (without rail contact) M 2,5/5.PI.Ex Green/yellow body (with rail contact) M 2,5/5.P.Ex UL 0.2-4 22-2 WG 0.22-2.5 End section grey blue yellow orange green 2 Circuit separator grey 3 Separator end section (block) grey 4 Separator end section (rail) grey Standard 6 mm block Terminal block for ground wire. Terminal block for ground wire. One circuit and four clamps 2.5 mm 2 2 WG 300 / s 0 mm /.39" 0.4-0.6 Nm / 3.5-5.3 Ib-in Exe : 750 V Exi : 90 V 24 I M2 / M II 2GD / GD LCIE 02 TEX 0025U FEM6 V0 FEM6 V0 FEM6 V0 FEM6 FEM6 SCM5 SCF6 SCFM6 th. 2,8 th. 2,8 th. 2,8 th. 2,8 th. 2,8 th. 3 th. 3 SN 46 04 R300 SN 46 05 R400 SN 46 240 R600 SN 46 06 R500 SN 46 259 R500 SN 99 302 R0700 SN 99 305 R0200 SN 03 26 R600 SN 03 25 R500 SN 6 728 R2500 SN 8 707 R0300 SN 4 825 R0500 M 4/6.Ex M 4/6.N.Ex M 4/6.Ex M 4/6.Ex M 4/6.PI.Ex M 4/6.P.Ex 0.2-4 0.22-4 UL 22-0WG 4 mm 2 0 WG 480 / s 9.5 mm /.37" 0.5-0.8 Nm / 4.4-7. Ib-in Exe : 750 V Exi : 375 V 32 I M2 / M II 2GD / GD LCIE 02 TEX 004U FEM6 V0 FEM6 V0 FEM6 V0 FEM6 FEM6 SCM6 SCF6 SCFM6 th. 2,8 th. 2,8 th. 2,8 th. 2,8 th. 2,8 th. 3 th. 3 SN 46 00 R2700 SN 46 002 R2000 SN 46 245 R0700 SN 46 285 R2000 SN 46 237 R2700 SN 46 023 R400 SN 46 259 R500 SN 99 302 R0700 SN 99 305 R0200 SN 03 26 R600 SN 03 25 R500 SN 3 003 R000 SN 8 707 R0300 SN 4 825 R0500 M 4/6.3.Ex M 4/6.3.N.Ex M 4/6.4.Ex M 4/6.4.N.Ex 0.2-4 0.22-4 22-0WG 9.5 mm /.37" 0.5-0.8 Nm / 4.4-7. Ib-in Exe : 420 V Exi : 90 V 32 I M2 / M II 2GD / GD LCIE 02 TEX 0028U FEM3 V0 (4) FEM3 (4) FEM4 V0 (5) FEM4 (5) SCM6 UL 4 mm 2 0 WG th. 2,8 th. 2,8 th. 2,8 th. 2,8 SN 46 00 R2300 SN 46 0 R000 SN 46 02 R00 SN 46 03 R200 SN 46 26 R0700 SN 26 576 R700 SN 46 262 R0000 SN 26 629 R2400 SN 3 003 R000 4 8 2 9 0 3 R 8 Preassembled 2 poles BJMI5 () jumper bar IP 20 touchproof 3 poles BJMI5 () 4 poles BJMI5 () not IP20 5 poles BJMI5 () see section : accessories 0 poles BJMI5 () 9 Connector plate EL6 0 Jumper bar not preassembled 20 poles Post + screw + washer Jumper bar not preassembled 20 poles BJS5 () EV5 Post + washer + captive screw IP20 2 Comb-type jumper bar 0 poles PC5 (3) Isolating cover EIP 3 Shielding connector th. 0.5 CBM5 th. 0.8 CBM8 4 Protection label 4 blocks Screw for protection label R See markers section Other accessories see section accessories These accessories cannot be mounted on M 2,5/5.P.Ex block SN 76 278 R600 BJMI6 () SN 76 279 R700 BJMI6 () SN 76 280 R0500 BJMI6 () SN 76 28 R2200 BJMI6 () SN 76 282 R2300 BJMI6 () SN 73 627 R200 EL6 SN 77 652 R0600 SN 68 629 R600 SN 3 544 R200 SN 3 550 R2400 SN 78 745 R400 SN 78 746 R500 BJS6 () EV6I PC6 (3) EIP CBM5 CBM8 EP6 VSP6 These accessories cannot be mounted on M 4/6.P.Ex block SN 76 663 R0000 BJMI6 () SN 76 664 R000 BJMI6 () SN 76 665 R0200 BJMI6 () SN 76 666 R0300 BJMI6 () SN 76 667 R0400 BJMI6 () SN 73 627 R200 EL6 SN 74 784 R2000 SN 206 394 R0200 SN 3 548 R2600 SN 3 550 R2400 SN 78 745 R400 SN 78 746 R500 SN 63 427 R700 SN 63 433 R500 BJS6 () EV6I PC6 (3) EIP RC 55 - RC50 RC 65 - RC60 RC 65 - RC60 () circuit separator SC is required with the use of these accessories. (2) Use of these accessories requires the cut-out of the block body (precut). (3) For other configurations of poles,.(4) For M 4/6.3...Ex. (5) For M 4/6.4...Ex. SN 76 663 R0000 SN 76 664 R000 SN 76 665 R0200 SN 76 666 R0300 SN 76 667 R0400 SN 73 627 R200 SN 74 784 R2000 SN 206 394 R0200 SN 3 548 R2600 SN 3 550 R2400 4

T07075 Standard and ground Terminal blocks M 6/8...Ex Spacing 8 mm.35" M 0/0...Ex Spacing 0 mm.394" M 6/2...Ex Spacing 2 mm.473" Screw clamp DIN -3 Exe and Exi voltage ratings apply to terminal blocks only without any accessory and mounted on DIN 3 rail. The use of ground terminal blocks do not decrease the standard terminal block's voltage ratings. For the terminal block voltage rating with its accessories, consult our "TEX technical instructions sheet for safe mounting". Standard 8 mm block M 6/8.P.Ex Spacing 8 mm.35" Standard 0 mm block M 0/0.P.Ex Spacing 0 mm.394" Standard 2 mm block with partition M 6/2.P.Ex Spacing 2mm.473" End stop th. 9 mm BDL V0 End stop th. 9, mm BM2 V0 Rail 35 x 7,5 x PR3.Z2 Rail 35 x 5 x 2,3 PR4 Rail 35 x 5 x,5 PR5 Rail 32 x 5 x,5 PR.Z2 Standard blocks UL 94 V0 Blue body SN 399 903 R0200 SN 296 35 R0000 SN 74 300 R700 SN 68 500 R200 SN 68 700 R2200 SN 63 050 R0400 Terminal block for ground wire. Terminal block for ground wire. Terminal block for ground wire. (M 0/0.P.Ex closed terminal block) (M 6/2.P.Ex closed terminal block) M 6/8.Ex M 6/8.N.Ex SN 46 003 R200 SN 46 004 R2200 M 0/0.Ex M 0/0.N.Ex SN 46 005 R2300 SN 46 006 R2400 M 6/2.Ex M 6/2.N.Ex SN 46 027 R000 SN 46 028 R200 Terminal blocks for Green/yellow body (without rail contact) M 6/8.PI.Ex ground wires UL 94 V0 Green/yellow body (with rail contact) M 6/8.P.Ex Wire size 0.5-0 0.5-6 Short circuit current (for ground blocks) / s Wire stripping length Recommended torque Nm / Ib.in Voltage EN 60079-7 / - II ; EN 50020 TEX marking TEX certificate ccessories 2 4 3 End section grey blue yellow orange green 2 Circuit separator grey 3 Separator end section (block) grey 4 Separator end section (rail) grey 22-8 WG 6 mm 2 8 WG 720 / s 2 mm /.47" 0.8- Nm / 7.-8.9 Ib-in Exe : 420 V Exi : 90 V 4 I M2 / M II 2GD / GD LCIE 02 TEX 004U FEM6 V0 FEM6 V0 FEM6 V0 FEM6 FEM6 SCM6 SCF6 SCFM6 th. 2,8 th. 2,8 th. 2,8 th. 2,8 th. 2,8 th. 3 th. 3 SN 46 238 R0000 M 0/0.PI.Ex SN 46 022 R300 M 0/0.P.Ex UL 0.5-6 0.5-0 SN 46 259 R500 SN 99 302 R0700 SN 99 305 R0200 SN 03 26 R600 SN 03 25 R500 SN 3 003 R000 SN 8 707 R0300 SN 4 825 R0500 20-6 WG 0 mm 2 6 WG 200 / s 2 mm /.47".2-.4 Nm / 0.6-2.3 Ib-in Exe : 420 V Exi : 90 V 57 I M2 / M II 2GD / GD LCIE 02 TEX 004U FEM6 V0 FEM6 V0 FEM6 V0 FEM6 FEM6 SCM6 SCF6 SCFM6 th. 2,8 th. 2,8 th. 2,8 th. 2,8 th. 2,8 th. 3 th. 3 SN 46 239 R000 M 6/2.PI.Ex SN 46 02 R200 M 6/2.P.Ex UL 0.5-25 0.5-6 SN 46 259 R500 SN 99 302 R0700 SN 99 305 R0200 SN 03 26 R600 SN 03 25 R500 SN 3 003 R000 SN 8 707 R0300 SN 4 825 R0500 8-6 WG 6 mm 2 4 WG 920 / s 4 mm /.55".2-.4 Nm / 0.6-2.3 Ib-in Exe : 550 V Exi : 375 V 76 I M2 / M II 2GD / GD LCIE 02 TEX 004U FEM2 V0 th. 2,8 FEM2 th. 2,8 FEM2 th. 2,8 FEM2 V0 th. 2,8 SCF 2 SCFM6 SN 46 29 R2600 SN 46 043 R2000 UL SN 46 270 R400 SN 28 68 R0300 SN 03 065 R2400 SN 98 68 R0200 SN 3 02 R000 SN 4 825 R0500 4 8 2 9 0 3 R 8 Preassembled 2 poles BJMI8 () jumper bar IP 20 touchproof 3 poles BJMI8 () 4 poles BJMI8 () not IP20 5 poles BJMI8 () see section : accessories 0 poles BJMI8 () 9 Connector plate EL6 0 Jumper bar not preassembled 20 poles Post + screw + washer Jumper bar not preassembled 20 poles Post + washer + captive screw IP20 BJS8 () EV6I 2 Comb-type jumper bar 0 poles PC8 (3) Isolating cover 3 Shielding connector th. 0.5 th. 0.8 4 Protection label 3 blocks EP6 4 blocks EP8 Screw for protection label VSP6 R See markers section These accessories cannot be mounted on M 6/8.P.Ex block RC 65 - RC60 - RC80 SN 76 669 R600 SN 76 670 R300 SN 76 67 R0000 SN 76 672 R000 SN 76 673 R0200 SN 73 627 R200 SN 74 789 R0500 SN 206 394 R0200 SN 63 33 R2400 SN 63 427 R700 SN 63 428 R2000 SN 63 433 R500 BJMI0 () BJMI0 () BJMI0 () BJMI0 () BJMI0 () BJS0() EV6I PC0 EP8 EP0 VSP6 These accessories cannot be mounted on M 0/0.P.Ex block RC 65 - RC60 - RC80 SN 76 675 R0400 SN 76 676 R0500 SN 76 677 R0600 SN 76 678 R700 SN 76 679 R000 BJMI2 (2) BJMI2 (2) BJMI2 (2) BJMI2 (2) BJMI2 (2) BJS2 (2) EV2 SN 77 654 R0000 SN 206 394 R0200 SN 63 35 R2600 SN 63 428 R2000 SN 63 429 R200 SN 63 433 R500 EP0 EP2 VSP2 These accessories cannot be mounted on M 6/2.P.Ex block RC 65 - RC60- RC80 SN 79 626 R0600 SN 79 628 R000 SN 79 629 R00 SN 79 630 R600 SN 79 63 R0300 SN 77 653 R0700 SN 68 664 R00 SN 63 429 R200 SN 63 430 R2600 SN 63 432 R400 Other accessories see section accessories () Use of these accessories requires the cut-out of the block body (precut). 5

T07076 Standard and ground Terminal blocks M 35/6...Ex Spacing 6 mm.630" M 70/22...Ex Spacing 22mm.866" M 95/26...Ex Spacing 26 mm.02" Screw clamp DIN -3 Exe and Exi voltage ratings apply to terminal blocks only without any accessory and mounted on DIN 3 rail. The use of ground terminal blocks do not decrease the standard terminal block's voltage ratings. For the terminal block voltage rating with its accessories, consult our "TEX technical instructions sheet for safe mounting". Standard 6 mm block with partition M 35/6.P.Ex Spacing 6 mm.630" Standard 22 mm block with partition M 70/22.P.Ex Spacing 22 mm.866" Standard 26 mm block with partition M 95/26.P.Ex Spacing 26 mm.02" End stop th. 2 mm BDH V2 End stop th. 2 mm BEH V2 End stop th. 9, mm BMH V0 V0 Rail 35 x 7,5 x PR3.Z2 Rail 35 x 5 x 2,3 PR4 Rail 35 x 5 x,5 PR5 Rail 32 x 5 x,5 PR.Z2 Standard blocks UL 94 V0 Blue body SN 6 900 R2700 SN 6 934 R0400 SN 94 836 R000 SN 74 300 R700 SN 68 500 R200 SN 68 700 R2200 SN 63 050 R0400 Terminal block for ground wire. (M 35/6.P.Ex closed terminal block) Terminal block for ground wire. (M 70/22.P.Ex closed terminal block) Terminal block for ground wire. (M 95/26.P.Ex closed terminal block) M 35/6.Ex M 35/6.N.Ex SN 46 029 R2200 SN 46 030 R2700 M 70/22.Ex M 70/22.N.Ex SN 46 025 R600 SN 46 026 R700 M 95/26.Ex M 95/26.N.Ex SN 46 020 R2500 SN 46 024 R500 Terminal blocks for ground wires UL 94 V0 ccessories Green/yellow body (without rail contact) Green/yellow body (with rail contact) Wire size Short circuit current (for ground blocks) / s Wire stripping length Recommended torque Nm / Ib.in Voltage EN 60079-7 ; EN 50020 TEX marking TEX certificate End section grey blue yellow M 35/6.P.Ex SN 46 044 R200 UL - 50 0-0 WG - 35 0- WG 35 mm 2 0 WG 4200 /s 7 mm /.67" 2.8-3 Nm / 24.9-26.7 Ib-in Exe : 750 V Exi : 375 V 25 I M2 / M II 2GD / GD LCIE 02 TEX 004U FEM6 V0 th. 3 FEM6 V0 th. 3 FEM6 th. 3 SN 46 27 R000 SN 99 304 R000 SN 03 06 R2000 M 70/22.PI.Ex M 70/22.P.Ex 6-95 6-70 SN 46 289 R0400 SN 46 073 R2600 M 95/26.P.Ex SN 46 068 R000 UL UL 4-00 WG 35-20 35-95 0000 WG 70 mm 2 00 WG 8400 /s 25 mm /.98" 6-7 Nm / 53.4-62.3 Ib-in Exe : 660 V Exi : 375 V 92 I M2 / M II 2GD / GD LCIE 02 TEX 0027U / 0023U FEM22 V0 th. 3 SN 46 269 R700 95 mm² 0000 WG 400 /s 26 mm /.02" 8.5-9.5 Nm / 74-83 Ib-in Exe : 750 V Exi : 375 V 232 I M2 / M II 2GD / GD LCIE 02 TEX 0022U / 0023U 2 Separator end section (block) grey SCF22 th. 3 SN 3 85 R600 5 6 2 5 Preassembled 2 poles jumper bar IP 20 touchproof 3 poles 4 poles not IP20 5 poles see section : accessories 0 poles 6 Jumper bar not preassembled 20 poles Post + screw + washer 7 Protection label 3 blocks 4 blocks Screw for protection label BJM6 () BJM6 () BJM6 () BJM6 () BJM6 () BJS6 () EV6 EP2 EP6 VSP6 0 poles SN 79 63 R000 SN 79 64 R0200 SN 79 65 R0300 SN 79 66 R0400 SN 79 67 R0500 SN 68 238 R600 SN 79 627 R0700 SN 63 430 R2600 SN 63 43 R300 SN 73 47 R2000 BJS22() BJS22() BJS22() BJS22() VSJ5 RDJ5 EP223 EP224 VSP22 2 poles 3 poles 5 poles 0 poles screw washer SN 73 36 R200 SN 73 37 R2200 SN 73 38 R0300 SN 73 39 R0400 SN 73 320 R000 SN 73 33 R2000 SN 73 327 R2400 SN 73 328 R0500 SN 73 323 R2000 BJS26 BJS26 BJS26 BJS26 VSJ5 RDJ5 2 poles 3 poles 5 poles 0 poles screw washer SN 77 508 R0700 SN 77 509 R0000 SN 77 50 R2400 SN 77 5 R00 SN 73 320 R000 SN 73 33 R2000 7 R R See markers section Other accessories see section accessories These accessories cannot be mounted on M 35/6.P.Ex block These accessories cannot be mounted on M 70/22.P.Ex block These accessories cannot be mounted on M 95/26.P.Ex block RC 65 - RC60 - RC80 RC 65 - RC60 - RC80 RC 65 - RC60- RC80 () circuit separator SC is required with the use of these accessories. (2) Use of these accessories requires the cut-out of the block body (precut). 6

T07077 Double-deck terminal blocks Screw clamp DIN -3 M 2,5/5.D2....Ex Spacing 5 mm.200" M 4/6.D2.Ex Spacing 6 mm.238" Exe and Exi voltage ratings apply to terminal blocks only without any accessory and mounted on DIN 3 rail. For the terminal block voltage rating with its accessories, consult our "TEX technical instructions sheet for safe mounting". Standard 5 mm block M 2,5/5.D2..Ex Standard 6 mm block Spacing 5 mm.200" End stop th. 2 mm BDH V2 End stop th. 2 mm BEH V2 End stop th. 9, mm BMH V0 V0 Rail 35 x 7,5 x PR3.Z2 Rail 35 x 5 x 2,3 PR4 Rail 35 x 5 x,5 PR5 Rail 32 x 5 x,5 PR.Z2 SN 6 900 R2700 SN 6 934 R0400 SN 94 836 R000 SN 74 300 R700 SN 68 500 R200 SN 68 700 R2200 SN 63 050 R0400 M 2,5/5.D2.Ex with partition Standard blocks UL 94 V0 Blue body M 2,5/5.D2.Ex M 2,5/5.D2.N.Ex SN 46 07 R600 SN 46 08 R2700 M 4/6.D2.Ex SN 46 009 R0700 M 2,5/5.D2..Ex SN 46 09 R2000 Wire size 0.2-4 0.22-2.5 UL 22-2 WG 0.2-4 0.22-4 UL 22-2 WG Wire stripping length Recommended torque Nm / Ib.in Voltage EN 60079-7 ; EN 50020 TEX marking TEX certificate ccessories End section grey blue 2.5 mm 2 2 WG 9 mm /.35" 0.4-0.6 Nm / 3.5-5.3 Ib-in Exe : 380 V Exi : 90 V 24 I M2 / M II 2GD / GD LCIE 02 TEX 0026U FEM6D V0 FEM6 th. th. SN 46 260 R200 SN 28 499 R2500 4 mm² 2 WG 8.5 mm /.33" 0.5-0.8 Nm / 4.4-7. lb.in Exe : 380 V Exi : 90 V 32 I M2 / M II 2GD / GD LCIE 02 TEX 009U FEM6D V0 FEM6D th. th. SN 46 260 R200 SN 28 499 R2500 2 2 Circuit separator grey Beige V0 3 Separator end section (block) grey SCM5D (3) th. SN 6 720 R200 SCM6D (3) SCM6D V0 (3) SCF6D th. th. th. SN 3 482 R0500 SN 93 482 R0600 SN 8 495 R700 3 9 2 8 7 0 7 Preassembled 2 poles jumper bar not IP 20 3 poles 4 poles 5 poles 0 poles 8 Preassembled 2 poles jumper bar 3 poles with IP 20 touchproof 4 poles 5 poles 0 poles 9 Connector plate 0 Jumper bar not preassembled Post + screw + washer Comb-type jumper bar 0 poles Isolating cover 2 Vertical inerconnection 3 Shielding connector th. 0.5 BJM5D () (2) BJM5D () (2) BJM5D () (2) BJM5D () (2) BJM5D () (2) BJMI5D () (2) BJMI5D () (2) BJMI5D () (2) BJMI5D () (2) BJMI5D () (2) EL6 BJS5D () (2) EV5D PC5 EIP ITV5 CBM5D 20 poles SN 76 226 R2200 SN 76 227 R2300 SN 76 228 R0400 SN 76 229 R0500 SN 76 230 R0200 SN 76 736 R200 SN 76 737 R2200 SN 76 738 R0300 SN 76 739 R0400 SN 76 740 R00 SN 73 627 R200 SN 77 65 R0500 SN 76 260 R000 SN 3 544 R200 SN 3 550 R2400 SN 76 259 R300 SN 73 530 R2400 BJM6D () (2) BJM6D () (2) BJM6D () (2) BJM6D () (2) BJM6D () (2) BJMI6D () (2) BJMI6D () (2) BJMI6D () (2) BJMI6D () (2) BJMI6D () (2) EL6 BJS6 () (2) EV6D PC6 ITV6 CBM5D 0 poles SN 73 55 R00 SN 73 56 R200 SN 73 57 R300 SN 73 59 R2500 SN 73 520 R2200 SN 79 668 R2000 SN 79 669 R200 SN 79 670 R2600 SN 79 67 R300 SN 79 672 R400 SN 73 627 R200 SN 68 485 R2700 SN 68 400 R600 SN 63 3 R2200 SN 68 962 R0400 SN 73 530 R2400 3 R R See markers section Other accessories see section accessories RC50 RC65 - RC60 () circuit separator SC is required with the use of these accessories. (2) Use of these accessories requires the cut-out of the block body (precut). (3) Except M 2,5/5.D2..Ex and M 4/6.D2..Ex 7

T07078 Three level sensor terminal blocks Screw clamp DIN 3 D 2,5/6.D...Ex Spacing 6 mm.238" Exe and Exi voltage ratings apply to terminal blocks only without any accessory and mounted on DIN 3 rail. For the terminal block voltage rating with its accessories, consult our "TEX technical instructions sheet for safe mounting". Three level block for power without ground protection. Power supply block for sensors/actuators - Three-wires without Led. End stop th. 2 mm BDH V2 End stop th. 9, mm BMH V0 V0 Rail 35 x 7,5 x PR3.Z2 Rail 35 x 5 x 2,3 PR4 Rail 35 x 5 x,5 PR5 SN 6 900 R2700 SN 94 836 R000 SN 74 300 R700 SN 68 500 R200 SN 68 700 R2200 Standard blocks UL 94 V0 Blue body D 2,5/6.D.Ex D 2,5/6.D.N.Ex SN 46 098 R2000 SN 46 04 R2300 Wire size 0.2-2.5 0.22-2.5 UL 20-2 WG Wire stripping length Recommended torque Nm / Ib.in Voltage EN 60079-7 ; EN 50020 TEX marking TEX certificate ccessories 2 End section grey 2 Preassembled 2 poles jumper bar 3 poles without IP 20 touchproof - 22 4 poles 5 poles 0 poles 20 poles 3 Connector plate 22 4 IDC jumper 24 2.5 mm 2 2 WG 6 mm /.24" 0.4-0.6 Nm / 3.5-5.3 Ib-in Exe : 60 V Exi : 30 V 22 I M2 / M II 2GD / GD LCIE 03 TEX 0024U FED3E th. 3 SN 6 77 R2000 BJD6 SN 78 024 R2500 BJD6 SN 78 025 R2600 BJD6 SN 78 026 R2700 BJD6 SN 78 027 R2000 BJD6 SN 78 032 R2500 BJD6 SN 78 033 R2600 EL6 SN 77 82 R700 D2,5 SN 4 205 R2000 3 4 R R See markers section RC65 RC65 red - blank SN 03 776 R000 blue - blank SN 03 775 R0000 Other accessories see section accessories 8

T07080 Safety connection terminal blocks M 4/6.RS.Ex Spacing 6 mm.238" M 6/8.RS.Ex Spacing 8 mm.35" M 0/0.RS.Ex Spacing 0 mm.394" Screw clamp DIN -3 Exe and Exi voltage ratings apply to terminal blocks only without any accessory and mounted on DIN 3 rail. For the terminal block voltage rating with its accessories, consult our "TEX technical instructions sheet for safe mounting". center of rail Compression clamp terminal for bare wire or equipped with bent lug. - spring under each wire-clamp Compression clamp terminal for bare wire or equipped with bent lug. - spring under each wire-clamp Compression clamp terminal for bare wire or equipped with bent lug. - spring under each wire-clamp End stop th. 9 mm BDL V0 End stop th. 9, mm BM2 V0 Rail 35 x 7,5 x PR3.Z2 Rail 35 x 5 x 2,3 PR4 Rail 35 x 5 x,5 PR5 Rail 32 x 5 x,5 PR.Z2 SN 399 903 R0200 SN 296 35 R0000 SN 74 300 R700 SN 68 500 R200 SN 68 700 R2200 SN 63 050 R0400 Ground wire-clamp holds 2 bent lugs, as above (not supplied) for connection of wires : 0.28 to.5 mm².0 to 2.5 mm² 2.5 to 6.0 mm² (only for M 0/0.RS.Ex) Standard blocks UL 94 V0 M 4/6.RS.Ex SN 46 350 R400 M 6/8.RS.Ex SN 46 2 R2500 M 0/0.RS.Ex SN 46 22 R2600 Wire size Screw clamp Lugs Wire stripping length Recommended torque Nm / Ib.in Voltage EN 60079-7 ; EN 50020 TEX marking TEX certificate ccessories End section grey BS TS 50-8 0.2-4 0.22-4 0.5 -.5 0.28 -.65 4 mm 2.65 mm 2 3 mm /.5" 0.5-0.8 Nm / 4.4-7. Ib-in Exe : 750 V Exi : 375 V 32 I M2 / M II 2GD / GD LCIE 05 TEX 004U FEMR8 th. 2,8 SN 46 272 R0200 BS TS 50-8 0.5-0 0.5-6 0.28-2.5 6 mm 2 2.5 mm 2 3 mm /.5" 0.8- Nm / 7.-8.9 Ib-in Exe : 550 V Exi : 375 V 4 I M2 / M II 2GD / GD LCIE 02 TEX 002U FEMR8 th. 2,8 SN 46 272 R0200 BS TS 50-8 0.5-6 0.5-0 0.28-6 0 mm 2 6 mm 2 4 mm /.55".2-.4 Nm / 0.6-2.3 Ib-in Exe : 550 V Exi : 375 V 46 I M2 / M II 2GD / GD LCIE 02 TEX 002U FEMR0 th. 2,8 SN 46 273 R0300 FEMR8 FEMR0 BJS0 + PL0 + VSJ 4 BJS8 + EV6I 5 6 7 4 Jumper bar not assembled Post + washer + captive screw IP20 Central socket for isolated interconnection Screw for central socket 5 ssembled jumper bar not IP 20 6 ssembled jumper bar with IP 20 touchproof 7 Short circuiting plug BJS6 () BJS6 () BJS6 () BJS6 () BJS6 () BJS6 () EV6I BJM6 () BJM6 () BJM6 () BJM6 () BJM6 () BJMI6 () BJMI6 () BJMI6 () BJMI6 () BJMI6 () 2 poles 3 poles 4 poles 5 poles 0 poles 20 poles 2 poles 3 poles 4 poles 5 poles 0 poles 2 poles 3 poles 4 poles 5 poles 0 poles SN 64 573 R2200 SN 64 574 R2300 SN 64 575 R2400 SN 64 736 R2500 SN 64 576 R2500 SN 74 784 R2000 SN 206 394 R0200 SN 68 56 R2500 SN 68 57 R2600 SN 68 58 R0700 SN 68 59 R0000 SN 68 973 R0700 SN 76 663 R0000 SN 76 664 R000 SN 76 665 R0200 SN 76 666 R0300 SN 76 667 R0400 BJS8 () BJS8 () BJS8 () BJS8 () BJS8 () BJS8 () BJS8 () EV6I BJM8 () BJM8 () BJM8 () BJM8 () BJM8 () BJMI8 () BJMI8 () BJMI8 () BJMI8 () BJMI8 () BP8.4 2 poles 3 poles 4 poles 5 poles 0 poles 5 poles 20 poles SN 64 58 R300 SN 64 582 R400 SN 64 583 R500 SN 64 737 R2600 SN 64 584 R600 SN 74 788 R0400 SN 74 789 R0500 SN 206 394 R0200 2 poles SN 68 520 R0500 3 poles SN 68 52 R2200 4 poles SN 68 522 R2300 5 poles SN 68 523 R2400 0 poles SN 68 974 R0000 2 poles SN 76 669 R600 3 poles SN 76 670 R300 4 poles SN 76 67 R0000 5 poles SN 76 672 R000 0 poles SN 76 673 R0200 SN 73 888 R2000 BJS0 () BJS0 () BJS0 () BJS0 () BJS0 () BJS0 () PT0 VSJ 2 poles SN 64 585 R700 3 poles SN 64 586 R000 4 poles SN 64 587 R00 5 poles SN 68 273 R00 0 poles SN 64 588 R2200 20 poles SN 77 654 R0000 SN 63 8 R00 SN 63 394 R2600 R R See markers section RC60 RC80 RC60 - RC80 Other accessories see section accessories () Use of these accessories requires the cut-out of the block body (precut). 9

T0708 Thermocouple terminal blocks Screw clamp DIN -3 Standard blocks UL 94 V0 Exe and Exi voltage ratings apply to terminal blocks only without any accessory and mounted on DIN 3 rail. For the terminal block voltage rating with its accessories, consult our "TEX technical instructions sheet for safe mounting". End stop th. 9 mm BDL V0 End stop th. 9, mm BM2 V0 Rail 35 x 7,5 x PR3.Z2 Rail 35 x 5 x 2,3 PR4 Rail 35 x 5 x,5 PR5 Rail 32 x 5 x,5 PR.Z2 SN 399 903 R0200 SN 296 35 R0000 SN 74 300 R700 SN 68 500 R200 SN 68 700 R2200 SN 63 050 R0400 MTC 6.Ex MTC 6.Ex Spacing 6 mm.238" 6 mm block for thermocouple conductors. SN 46 227 R2500 Thermocouple terminal blocks BB Entrelec's MTC 6.Ex thermocouple terminal block provides an interface for connecting thermocouple wire with virtually no loss of signal integrity. The interface design ensures positive wire continuity and allows selection and inventory of one terminal block for all thermocouple material. Figure : MTC 6.Ex with shield connector The thermocouple principle is based on the reaction of different metals to temperature. When thermocouple wires are terminated or connected, the "metal balance" must be maintained. The introduction of a foreign material (such as copper) results in loss of signal strength and integrity. When running extended or intermittent lengths of thermocouple wire, to a measurement instrument, two solutions are available :. When signals are carried over a long distance, a thermocouple transmitter is required. The thermocouple signal, in millivolts (mv), is converted to a milliampere (m) signal (i.e. 4-20 m) for ease of transmission. 2. When thermocouple wire is of insufficient length, termination and interconnection, using terminal blocks, will extend its length. Wire size Wire stripping length Recommended torque Nm / Ib.in Voltage EN 60079-7 ; EN 50020 TEX marking TEX certificate ccessories End section grey 2 Shield connector 3 mm max. /.22" 0.4-0.6 Nm / 3.5-5.3 lb.in Exe : 550 V Exi : 90 V I M2 / M II 2GD / GD LCIE 02 TEX 0025U FEM6 V0 CBM5 CBM6 2 conductors for thermocouple (DI. 0.9 -.5 mm) th. 2.8 SN 46 259 R500 th. 0.5 SN 78 745 R400 th. 0.8 SN 78 746 R500 Universal terminal block Other thermocouple terminal blocks are available with hardware (screws, clamps and connecting bar) which match the thermocouple material being used. This requires inventory of many different terminal block types. BB Entrelec's MTC 6.Ex terminal block adapts to all thermocouple material. This "neutral" method of connection limits the introduction of foreign materials to an insignificant level. The thermocouple wire insulation is stripped (3 mm maximum) and the bare wires are superimposed on one another. The thermocouple wires are in contact over their complete 3 mm length and tightened at two points by round tip screws (see figure 2). 2 The screws, made of plated brass, have only a mechanical function, that of holding the wires together with a point contact. Thus, the pressure points are not relevant in the connection environment. One thermocouple lead connects through one terminal block. The MTC 6 requires only 6 mm of space, allowing 50 terminals per foot of rail. Thermocouple shield wire connector bar R R See markers section RC65 - RC60 The MTC 6.Ex can be field of factory equipped with a shield connector bar (see figure ). This bar, made of brass, tin coated mounts in the lower part of the terminal block. It ensures the continuity of the thermocouple wire shield through the terminal block or to ground with no additional spacing. Other accessories see section accessories 20

T07082 Power terminal blocks DIN 3 with bistable foot and base mounting D 35/27.FF.Ex Spacing 27 mm.06" D 70/32.FF.Ex Spacing 32 mm.26" D 20/42.FF.Ex Spacing 42 mm.65" Exe voltage ratings apply to terminal blocks only without any accessory and mounted on DIN 3 rail. For the terminal block voltage rating with its accessories, consult our "TEX technical instructions sheet for safe mounting". 2 studs M6 2 studs M8 2 studs M0 End stop th. 2 mm BDH V2 End stop th. 9, mm BMH V0 V0 Rail 35 x 7,5 x PR3.Z2 Rail 35 x 5 x 2,3 PR4 Rail 35 x 5 x,5 PR5 SN 6 900 R2700 SN 94 836 R000 SN 74 300 R700 SN 68 500 R200 SN 68 700 R2200 Standard block UL 94 V0 D 35/27.FF.Ex SN 46 307 R0600 Delivered with 2 covers D 70/32.FF.Ex SN 46 308 R700 Delivered with 2 covers D 20/42.FF.Ex SN 46 309 R000 Delivered with 2 covers Wire size Lug D 35/27.FF.Ex SN 46 302 R000 Without cover (C4) 2.5-35 2.5-50 (C4) 2.5-35 2.5-35 D 70/32.FF.Ex SN 46 303 R0200 Without cover (C6) 6-95 6-70 (C6) 6-70 6-70 D 20/42.FF.Ex SN 46 304 R0300 Without cover (C8) 6-50 6-20 (C8) 6-20 Recommended wrench Lug / Central bolt Recommended torque Nm / Ib.in Voltage EN 60079-7 TEX marking TEX certificate ccessories Rotating protective cover IP20 Grey 35 mm² 35 mm² H0 mm / 6 mm llen key 3 Nm / 26. Ib-in / 6 Nm / 52 Ib-in. 750 V 25 I M2 - II 2GD Ex e LCIE 03 TEX 0034U CPUF35 SN 90 06 R600 70 mm² 70 mm² H3 mm / 6 mm llen key 6 Nm / 52 Ib-in / 6 Nm / 52 Ib-in. 750 V 92 I M2 - II 2GD Ex e LCIE 03 TEX 0034U CPUF70 SN 90 07 R700 20 mm² 20 mm² H7 mm / 6 mm llen key 0 Nm / 87 Ib-in / 6 Nm / 52 Ib-in. 750 V 269 I M2 - II 2GD Ex e LCIE 03 TEX 0034U CPUF20 SN 90 08 R2000 2 Jumper bar with CHc screws 2 poles 3 poles 3 TP for faston 6.35 x 0.8 mm and screw BJS27 BJS27 DRF6 SN 205 772 R300 SN 205 773 R400 SN 205 767 R600 BJS32 BJS32 DRF8 SN 205 774 R500 SN 205 775 R600 SN 205 768 R2700 BJS42 BJS42 DRF0 SN 205 776 R700 SN 205 777 R000 SN 205 769 R2000 2 3 R R See marking chapter RC80 (on cover) - RC80, RPC (on the middle) RC80 (on cover) - RC80, RPC (on the middle) RC80 (on cover) - RC80, RPC (on the middle) Other accessories see section accessories 2

T07083 Power terminal blocks DIN 3 with bistable foot and base mounting D 85/55.FF.Ex Spacing 55 mm 2.6" D 300/55.FF.Ex Spacing 55 mm 2.6" Exe voltage ratings apply to terminal blocks only without any accessory and mounted on DIN 3 rail. For the terminal block voltage rating with its accessories, consult our "TEX technical instructions sheet for safe mounting". 2 studs M2 2 studs M6 End stop th. 2 mm BDH V2 End stop th. 9, mm BMH V0 V0 Rail 35 x 7,5 x PR3.Z2 Rail 35 x 5 x 2,3 PR4 Rail 35 x 5 x,5 PR5 SN 6 900 R2700 SN 94 836 R000 SN 74 300 R700 SN 68 500 R200 SN 68 700 R2200 Standard block UL 94 V0 D 85/55.FF.Ex SN 46 30 R0400 Delivered with 2 covers D 300/55.FF.Ex SN 46 3 R200 Delivered with 2 covers Wire size Lug /MCM Recommended wrench lug / central bolt Recommended torque Nm / Ib.in Voltage EN 60079-7 TEX marking TEX certificate ccessories Rotating protective cover IP20 Grey D 85/55.FF.Ex SN 46 305 R0400 Without cover (C) 25-240 6-85 (C) 6-85 85 mm² 85 mm² H9 mm / 6 mm llen key 4 Nm / 2 Ib-in / 6 Nm / 52 Ib-in. 750 V 353 I M2 - II 2GD Ex e LCIE 03 TEX 0034U CPUF85 SN 90 09 R200 D 300/55.FF.Ex SN 46 306 R0500 Without cover 25-300 6-300 6-300 300 mm² 300 mm² H24 mm / 6 mm llen key 25 Nm / 27 Ib-in / 6 Nm / 52 Ib-in. 750 V 520 I M2 - II 2GD Ex e LCIE 03 TEX 0034U CPUF85 SN 90 09 R200 2 Jumper bar with CHc screws 2 poles 3 poles 3 TP for faston 6.35 x 0.8 mm and screw BJS5 BJS5 DRF2 SN 205 778 R200 SN 205 779 R2200 SN 205 770 R2500 BJS5 BJS5 DRF6 SN 205 778 R200 SN 205 779 R2200 SN 205 77 R200 2 3 R R See marking chapter Other accessories see section accessories RC80 (on cover) - RC80, RPC (on the middle) RC80 (on cover) - RC80, RPC (on the middle) 22

T07089 Power terminal blocks Drilling position for base mounting and dimensions with covers Particular conditions for mounting Mounting with B C D F G G2 H D 35/27... 2 Screws 00,5 7,5 6,5 / 63,5 36,5 60 82,5 D 70/32... 2 Screws 20 7,5 6,5 / 72,5 65 90,5 05,7 D 20/42... 2 Screws 20 7,5 6,5 / 83,5 97 255,5 29,7 D 85/55... 4 Screws 35 3,5 6,5 8,5 03,5 228,5 295 5,5 D 300/55... 4 Screws 35 3,5 6,5 8,5 05 / 295 / Dimensions in mm. Locking foot operating with screwdriver DI. 4 Locking Between blocks with stul Marking Center opening (to be made after jumper bar has been removed). s soon as the screwdriver is removed, the locking foot comes back to closed position 2 RC 80 or RC 00 RPC type setting marker, or RC 80 marker Side opening. The locking foot remains in open or closed position. 2 slots,2 RC80 not separated or RC 00 in slot With M3 screw Jumper bar - move the marker holders up - cut out the partition - screw the jumper bar M3 nut on one side M3 nut + washer on the other side Mounting of the derivative system Unlocking Locking 23

T07084 Standard and ground Miniblocks Screw clamp DIN 2 DR 4/6....Ex Spacing 6 mm.238" Exe and Exi voltage ratings apply to terminal blocks only without any accessory. The use of ground terminal blocks do not decrease the standard terminal block's voltage ratings. DR 4/6.Ex : Standard block 6 mm DR 4/6..Ex : Standard block 6 mm with partition. DR 4/6.P.Ex End stop th. 6.5 mm BDRL V0 Rail 5 x 5 x PR2 SN 99 420 R200 SN 64 600 R200 Terminal block for ground wire. Standard blocks UL 94 V0 Terminal blocks for ground wires UL 94 V0 Wire size Blue body Blue body Green/yellow body (with rail contact) With isolated ferrule DR 4/6.Ex DR 4/6..Ex DR 4/6.N.Ex DR 4/6..N.Ex SN 46 99 R2200 SN 46 200 R700 SN 46 276 R0600 SN 46 277 R0700 DR 4/6.P.Ex SN 46 20 R0400 UL 0.2-4 0.22-4 8-2 WG Wire stripping length Recommended torque Nm / Ib.in Voltage EN 60079-7 ; EN 50020 TEX marking TEX certificate ccessories End section grey blue 4 mm 2 2 WG 9.5 mm max. /.37" 0.5-0.8 Nm / 4.4-7. lb.in Exe : 275 V Exi : 90 V 30 I M2 / M II 2GD / GD LCIE 02 TEX 007U / 0024U FEDR6 V0 FEDR6 th. th. SN 46 293 R2000 SN 27 600 R0500 2 Circuit separator white SCDR6 th. 0,3 SN 73 06 R000 2 6 7 6 ssembled 2 poles jumper bar not IP20 3 poles 4 poles 5 poles 6 poles 7 poles 8 poles 9 poles 0 poles 7 Jumper bar not assembled Post + screw + washer 8 Pivoting jumper bar 9 Comb-type jumper bar 0 poles 0 Protection label 3 blocks Screw for protection label BJM62 () BJM62 () BJM62 () BJM62 () BJM62 () BJM62 () BJM62 () BJM62 () BJM62 () BJPD6 PC6 EPD6 VSPD6 32 SN 73 27 R2600 32 SN 73 28 R0700 32 SN 73 29 R0000 32 SN 73 22 R2200 32 SN 74 2 R600 32 SN 74 3 R700 32 SN 74 4 R000 32 SN 74 5 R00 32 SN 73 226 R2700 SN 73 223 R2400 SN 63 3 R2200 SN 73 206 R0400 SN 73 207 R0500 8 9 0 R R See markers section Other accessories see section accessories RC65 () Use of these accessories requires the cut-out of the block body (precut). 24

T07085 Standard and ground Terminal blocks D 2,5/5....2L.Ex Spacing 5 mm.200" D 2,5/5....3L.Ex Spacing 5 mm.200" D 2,5/5....4L.Ex Spacing 5 mm.200" Spring clamp DIN 2 58 80 Exe and Exi voltage ratings apply to terminal blocks only without any accessory. The use of ground terminal blocks do not decrease the standard terminal blocks' voltage ratings. wire per spring. For the terminal block voltage rating with its accessories, consult our "TEX technical instructions sheet for safe mounting". center of rail 29 Terminal block with 2 springs D 2,5/5.P.2L.Ex Spacing 5 mm.200" 45,5 38 Terminal block with 3 spring D 2,5/5.P.3L.Ex Spacing 5 mm.200" center of rail 40 Terminal block with 4 spring D 2,5/5.P.4L.Ex Spacing 5 mm.200" 45,5 38 End stop th. 9 mm BDL V0 End stop th. 9, mm BM2 V0 Rail 35 x 7,5 x PR3.Z2 Rail 35 x 5 x 2,3 PR4 Rail 35 x 5 x,5 PR5 Standard blocks UL 94 V0 Blue body SN 399 903 R0200 SN 296 35 R0000 SN 74 300 R700 SN 68 500 R200 SN 68 700 R2200 Terminal block with 2 springs for ground wire. D 2,5/5.2L.Ex D 2,5/5.N.2L.Ex SN 46 053 R2200 SN 46 052 R200 Terminal block with 3 springs for ground wire D 2,5/5.3L.Ex D 2,5/5.N.3L.Ex SN 46 055 R2400 SN 46 056 R2500 Terminal block with 4 springs for ground wire D 2,5/5.4L.Ex D 2,5/5.N.4L.Ex SN 46 049 R0600 SN 46 050 R0300 Terminal blocks for ground wires UL 94 V0 ccessories Green/yellow body (with rail contact) Wire size With isolated ferrule Short circuit current (for ground blocks) / s Wire stripping length Recommended screwdriver Voltage EN 60079-7 ; EN 50020 TEX marking TEX certificate End section grey orange 2 Circuit separator orange D 2,5/5.P.2L.Ex SN 46 054 R2300 0.2-4 0.2-2.5 0.5-2.5 2.5 mm 2 300 / s 9.5 mm /.37" 3.5 mm /.4" Exe : 550 V Exi : 60 V 24 I M2 / M II 2GD / GD LCIE 02 TEX 003U FED5.2L FED5.2L SCD5.2L SN 29 06 R2400 SN 29 062 R2500 SN 29 352 R0400 D 2,5/5.P.3L.Ex SN 46 057 R2600 0.2-4 0.2-2.5 0.5-2.5 2.5 mm 2 300 / s 9.5 mm /.37" 3.5 mm /.4" Exe : 550 V Exi : 60 V 24 I M2 / M II 2GD / GD LCIE 02 TEX 000U FED5.3L FED5.3L SCD5.3L SN 29 05 R2200 SN 29 052 R2300 SN 29 362 R0600 D 2,5/5.P.4L.Ex SN 46 05 R2000 0.2-4 0.2-2.5 0.5-2.5 2.5 mm 2 300 / s 9.5 mm /.37" 3.5 mm /.4" Exe : 550 V Exi : 60 V 24 I M2 / M II 2GD / GD LCIE 02 TEX 000U FED5.4L FED5.4L SCD5.4L SN 29 04 R2000 SN 29 042 R200 SN 29 372 R0000 4 2 4 Jumper bar orange IP 20-24 5 Jumper bar orange between 2 blocks, different spacing - spacing 5 and 6 mm IP 20-24 - spacing 5 and 8 mm IP 20-24 6 Shielding connector BJDL5.2 BJDL5.3 BJDL5.4 BJDL5.5 BJDL5.6 BJDL5.7 BJDL5.8 BJDL5.9 BJDL5.0 BJDPL5.6 () BJDPL5.8 () CBD5.2L 2 poles 3 poles 4 poles 5 poles 6 poles 7 poles 8 poles 9 poles 0 poles th. 0,5 SN 29 02 R2300 SN 29 03 R2400 SN 29 04 R2500 SN 29 05 R2600 SN 29 06 R2700 SN 29 07 R2000 SN 29 08 R000 SN 29 09 R0200 SN 29 0 R2600 SN 29 50 R0600 SN 29 60 R0000 SN 29 077 R2400 BJDL5.2 BJDL5.3 BJDL5.4 BJDL5.5 BJDL5.6 BJDL5.7 BJDL5.8 BJDL5.9 BJDL5.0 BJDPL5.6 () BJDPL5.8 () 2 poles 3 poles 4 poles 5 poles 6 poles 7 poles 8 poles 9 poles 0 poles SN 29 02 R2300 SN 29 03 R2400 SN 29 04 R2500 SN 29 05 R2600 SN 29 06 R2700 SN 29 07 R2000 SN 29 08 R000 SN 29 09 R0200 SN 29 0 R2600 SN 29 50 R0600 SN 29 60 R0000 BJDL5.2 BJDL5.3 BJDL5.4 BJDL5.5 BJDL5.6 BJDL5.7 BJDL5.8 BJDL5.9 BJDL5.0 BJDPL5.6 () BJDPL5.8 () 2 poles 3 poles 4 poles 5 poles 6 poles 7 poles 8 poles 9 poles 0 poles SN 29 02 R2300 SN 29 03 R2400 SN 29 04 R2500 SN 29 05 R2600 SN 29 06 R2700 SN 29 07 R2000 SN 29 08 R000 SN 29 09 R0200 SN 29 0 R2600 SN 29 50 R0600 SN 29 60 R0000 5 6 R R See markers section Other accessories see section accessories This accessory cannot be mounted on M 2.5/5.P.L2.Ex block RC50, RPC (on top) - RC55 (on side) RC50, RPC (on top) - RC55 (on side) RC50, RPC (on top) - RC55 (on side) () Insert an end section between the 2 connected blocks 25

T0703 Standard and ground Terminal blocks Spring clamp DIN 2 D 2,5/5.I.3L.Ex Spacing 5 mm.200" Exe and Exi voltage ratings apply to terminal blocks only without any accessory. The use of ground terminal blocks do not decrease the standard terminal blocks' voltage ratings. wire per spring. For the terminal block voltage rating with its accessories, consult our "TEX technical instructions sheet for safe mounting". * Can accept 4 mm² rigid wire. Terminal block with 2 springs End stop th. 9 mm BDL V0 End stop th. 9, mm BM V2 End stop th. 9, mm BM V0 V0 Rail 35 x 7,5 x PR3.Z2 Rail 35 x 5 x 2,3 PR4 Rail 35 x 5 x,5 PR5 SN 399 903 R0200 SN 03 002 R2600 SN 99 306 R0300 SN 74 300 R700 SN 68 500 R200 SN 68 700 R2200 Standard blocks UL 94 V0 D 2,5/5.I.3L.Ex SN 46 352 R0200 Terminal blocks for ground wires UL 94 V0 Green/yellow body (with rail contact) Wire size With isolated ferrule Short circuit current (for ground blocks) / s Wire stripping length Recommended screwdriver Voltage EN 60079-7 ; EN 50020 TEX marking 0.2-4* 0.2-2.5 0.5-2.5 2.5 mm 2 300 / s 9,5 mm /.37" 3.5 mm /.4" Exe : 630 V Exi : 375 V 24 I M2 / M II 2GD / GD TEX certificate ccessories End section grey orange 2 Circuit separator orange FED5.2L FED5.2L SCD5.2L LCIE 05 TEX 005U SN 29 06 R2400 SN 29 062 R2500 SN 29 352 R0400 4 2 4 Jumper bar orange IP 20-24 5 Jumper bar orange between 2 blocks, different spacing - spacing 5 and 6 mm IP 20-24 - spacing 5 and 8 mm IP 20-24 6 Shielding connector BJDL5.2 BJDL5.3 BJDL5.4 BJDL5.5 BJDL5.6 BJDL5.7 BJDL5.8 BJDL5.9 BJDL5.0 BJDPL5.6 () BJDPL5.8 () CBD5.2L 2 poles 3 poles 4 poles 5 poles 6 poles 7 poles 8 poles 9 poles 0 poles th. 0,5 SN 29 02 R2300 SN 29 03 R2400 SN 29 04 R2500 SN 29 05 R2600 SN 29 06 R2700 SN 29 07 R2000 SN 29 08 R000 SN 29 09 R0200 SN 29 0 R2600 SN 29 50 R0600 SN 29 60 R0000 SN 29 077 R2400 5 6 R R See markers section Other accessories see section accessories This accessory cannot be mounted on M 2.5/5.P.L2.Ex block RC50, RPC (on top) - RC55 (on side) () Insert an end section between the 2 connected blocks 26

T07086 Standard and ground Terminal blocks D 2,5/5.....2L.2L.Ex Spacing 5 mm.200" D 4/6....2L.Ex Spacing 6 mm.236" D 6/8....2L.Ex Spacing 8 mm.35" Spring clamp DIN 3 Exe and Exi voltage ratings apply to terminal blocks only without any accessory. The use of ground terminal blocks do not decrease the standard terminal blocks' voltage ratings. wire per spring. For the terminal block voltage rating with its accessories, consult our "TEX technical instructions sheet for safe mounting". Double circuit Terminal block with 4 springs with 2 electrically separated circuits. Each circuit has its own test socket and can be jumpered independently. * Marking to make a difference between the D 2,5/5....4L.Ex and the D 2,5/5.2L.2L.Ex terminal blocks. Same dimensions as D 2,5/5...4L.Ex Terminal block with 2 springs D 4/6.P.2L.Ex Spacing 6 mm.236" Terminal block with 2 springs D 6/8.P.2L.Ex Spacing 8 mm.35" End stop th. 9 mm BDL V0 End stop th. 9, mm BM2 V0 Rail 35 x 7,5 x PR3.Z2 Rail 35 x 5 x 2,3 PR4 Rail 35 x 5 x,5 PR5 SN 399 903 R0200 SN 296 35 R0000 SN 74 300 R700 SN 68 500 R200 SN 68 700 R2200 Terminal block with 2 springs for ground wire. Terminal block with 2 springs for ground wire. Standard blocks UL 94 V0 Blue body D 2,5/5.2L.2L.Ex D 2,5/5.N.2L.2L.Ex SN 46 047 R2400 SN 46 048 R0500 D 4/6.2L.Ex D 4/6.N.2L.Ex SN 46 25 R0500 SN 46 058 R0700 D 6/8.2L.Ex D 6/8.N.2L.Ex SN 46 059 R0000 SN 46 060 R0500 Terminal blocks for ground wires UL 94 V0 ccessories Green/yellow body (with rail contact) Wire size With isolated ferrule Short circuit current (for ground blocks) / s Wire stripping length Recommended screwdriver Voltage EN 60079-7 ; EN 50020 TEX marking TEX certificate End section grey orange 2 Circuit separator orange 0.2-4 0.2-2.5 0.5-2.5 2.5 mm 2 9.5 mm /.37" 3.5 mm /.4" Exe : 0 V Exi : 60 V 24 I M2 / M II 2GD / GD LCIE 02 TEX 000U FED5.4L FED5.4L SCD5.4L SN 29 04 R2000 SN 29 042 R200 SN 29 372 R0000 D 4/6.P.2L.Ex SN 46 253 R0700 0.2-6 0.2-4 0.5-4 4 mm 2 480 / s mm /.43" 4 mm /.6" Exe : 660 V Exi : 90 V 32 I M2 / M II 2GD / GD LCIE 02 TEX 005U FED5.2L FED5.2L SCD5.2L SN 29 06 R2400 SN 29 062 R2500 SN 29 352 R0400 D 6/8.P.2L.Ex SN 46 06 R2200 0.5-0 0.5-6 0.5-6 6 mm 2 720 / s 2.5 mm /.49" 5.5 mm /.22" Exe : 550 V Exi : 90 V 4 I M2 / M II 2GD / GD LCIE 02 TEX 005U FED8.2L FED8.2L SN 29 6 R2500 SN 29 62 R2600 4 2 4 Jumper bar orange IP 20-24 5 Jumper bar orange between 2 blocks, different spacing - spacing 5 and 6 mm IP 20-24 - spacing 5 and 8 mm IP 20-24 - spacing 6 and 8 mm IP 20-32 BJDL5.2 BJDL5.3 BJDL5.4 BJDL5.5 BJDL5.6 BJDL5.7 BJDL5.8 BJDL5.9 BJDL5.0 BJDPL5.6 () BJDPL5.8 () 2 poles 3 poles 4 poles 5 poles 6 poles 7 poles 8 poles 9 poles 0 poles SN 29 02 R2300 SN 29 03 R2400 SN 29 04 R2500 SN 29 05 R2600 SN 29 06 R2700 SN 29 07 R2000 SN 29 08 R000 SN 29 09 R0200 SN 29 0 R2600 SN 29 50 R0600 SN 29 60 R0000 BJDL6.2 BJDL6.3 BJDL6.4 BJDL6.5 BJDPL5.6 () BJDPL6.8 () 2 poles 3 poles 4 poles 5 poles SN 29 28 R2400 SN 29 29 R2500 SN 29 94 R700 SN 29 95 R000 SN 29 50 R0600 SN 29 70 R0200 BJDL8.2 BJDL8.3 BJDL8.4 BJDL8.5 BJDPL5.8 () BJDPL6.8 () 2 poles 3 poles 4 poles 5 poles SN 29 22 R600 SN 29 23 R700 SN 29 44 R2400 SN 29 45 R2500 SN 29 60 R0000 SN 29 70 R0200 5 R R See markers section Other accessories see section accessories RC50, RPC (on top) - RC55 (on side) RC60, RPC (on top) - RC65 (on side) RC60, RC80, RPC (on top) - RC65, RCL (on side) () Insert an end section between the 2 connected blocks 27

T07087 Standard and ground Terminal blocks D 0/0.2L.Ex Spacing 0 mm.394" D 6/2.2L.Ex Spacing 2 mm.473" D 35/6.2L.Ex Spacing 6 mm.630" Spring clamp DIN 3 Exe and Exi voltage ratings apply to terminal blocks only without any accessory. The use of ground terminal blocks do not decrease the standard terminal blocks' voltage ratings. wire per spring. For the terminal block voltage rating with its accessories, consult our "TEX technical instructions sheet for safe mounting". Terminal block with 2 springs with test + interconnection on one side D 0/0.P.2L.Ex Spacing 0 mm.394" Terminal block with 2 springs with test + interconnection on both sides D 6/2.P.2L.Ex Spacing 2 mm.473" Terminal block with 2 springs with test + interconnection on both sides D 35/6.P.2L.Ex Spacing 6 mm.630" End stop th. 9 mm BDL V0 End stop th. 9, mm BM V2 End stop th. 9, mm BM V0 V0 Rail 35 x 7,5 x PR3.Z2 Rail 35 x 5 x 2,3 PR4 Rail 35 x 5 x,5 PR5 Standard blocks UL 94 V0 Blue body SN 399 903 R0200 SN 03 002 R2600 SN 99 306 R0300 SN 74 300 R700 SN 68 500 R200 SN 68 700 R2200 Terminal block with 2 springs for ground Terminal block with 2 springs for ground Terminal block with 2 springs for ground wire. wire. wire. D 0/0.2L.Ex D 0/0.N.2L.Ex SN 46 8 R2000 SN 46 20 R2600 D 6/2.2L.Ex D 6/2.N.2L.Ex SN 46 30 R2000 SN 46 32 R600 D 36/6.2L.Ex D 35/6.N.2L.Ex SN 46 36R200 SN 46 38 R2400 Terminal blocks for ground wires UL 94 V0 ccessories Green/yellow body (with rail contact) Wire size Short-circuit current (for ground blocks) / s Wire stripping length Recommended screwdriver Voltage EN 60079-7 ; EN 50020 TEX marking TEX certificate End section grey D 0/0.P.2L.Ex 0.5-6 0.5-0 0 mm 2 200 / s 2 mm /.47" 5,5 mm /.22" Exe : 550 V Exi : 375 V 57 I M2 / M II 2GD / GD LCIE 05 TEX 006U FED0.2L FED0.2L SN 46 22 R400 D 6/2.P.2L.Ex 0.5-25 0.5-6 SN 29 46 R2200 SN 29 462 R2300 6 mm 2 920 / s 9 mm /.79" 6,5 mm /.26" Exe : 550 V Exi : 375 V 76 I M2 / M II 2GD / GD LCIE 05 TEX 006U FED2.2L FED2.2L FED2.2L SN 46 34 R000 D 35/6.P.2L.Ex 2.5-50 2.5-35 SN 399 57 R0400 SN 399 572 R0500 SN 399 574 R0700 35 mm 2 4200 / s 26 mm /.02" 6,5 mm /.26" Exe : 750 V Exi : 375 V 25 I M2 / M II 2GD / GD LCIE 05 TEX 006U SN 46 40 R0200 3 Jumper bar orange 57 - D 0/0.2L.Ex 76 - D 6/2.2L.Ex 5 - D 35/6.2L.Ex 4 Jumper bar orange between 2 blocks, different spacing - spacing 5 and 6 mm IP 20-24 - spacing 6 and 0 mm IP 20-32 - spacing 8 and 0 mm IP 20-4 BJDL.0.2 () 2 poles BJDL.0.3 () 3 poles BJDL.0.4 () 4 poles BJDL.0.5 () 5 poles BJDPL5.0 (2) BJDPL6.0 (2) BJDPL8.0 (2) SN 29 472 R2500 SN 29 474 R2700 SN 29 476 R200 SN 29 478 R0300 SN 29 480 R2200 SN 29 482 R000 SN 29 484 R200 BJDL2.2 () 2 poles SN 399 563 R0400 BJDL6.2 () 2 poles SN 399 62 R0600 3 4 R R See markers section Other accessories see section accessories RC00, RC80, RCC60 (on top) RCL85, RC65 (on side) RC00, RC80, RCC60 (on top) RCL85, RC65 (on side) RC00, RC80, RCC60 (on top) RCL85, RC65 (on side) () No voltage decrease EExe and EExi with BJDL - (2) Insert an end section between the 2 connected blocks 28

T07090 Standard and ground miniblocks - Spring clamp DIN 2 - Base mount with flanges DR 2,5/5.2L.Ex Spacing 5 mm.200" DB 2,5/5.2L.Ex Exe and Exi voltage ratings apply to terminal blocks only without any accessory. The use of ground terminal blocks do not decrease the standard terminal blocks' voltage ratings. wire per spring. For the terminal block voltage rating with its accessories, consult our "TEX technical instructions sheet for safe mounting". Miniblock with 2 springs DR 2,5/0.P.4L.Ex Spacing 0 mm.396" 33,5 Miniblock with 2 springs 30 center of rail 6,5 End stop th. 6.5 mm BDRL V0 Rail 5 x 5 x PR2 SN 99 420 R200 SN 64 600 R200 Ground miniblock with 4 springs Standard blocks UL 94 V0 Blue body DR 2,5/5.2L.Ex DR 2,5/5.N.2L.Ex SN 46 207 R0200 SN 46 279 R00 DB 2,5/5.2L.Ex DB 2,5/5.N.2L.Ex SN 46 246 R0000 SN 46 247 R000 Terminal blocks for ground wires UL 94 V0 ccessories 3 2 Green/yellow body (with rail contact) Wire size With isolated ferrule Short-circuit current (for ground blocks) / s Wire stripping length Recommended screwdriver Voltage EN 60079-7 ; EN 50020 TEX marking TEX certificate End section grey orange 2 Kit end section grey (right + left) orange 3 Separator section grey orange 4 Jumper bar orange IP 20-24 5 Jumper bar orange IP 20-24 DR 2,5/0.P.4L.Ex SN 46 263 R000 0.2-4 0.2-4 0.2-2.5 0.2-2.5 0.5-2.5 0.5-2.5 2.5 mm 2 2.5 mm 2 300 / s 9.5 mm /.37" 3.5 mm /.4" 9.5 mm /.37" 3.5 mm /.4" Exe : 275 V Exi : 60 V Exe : 275 V Exi : 60 V 24 24 I M2 / M II 2GD / GD I M2 / M II 2GD / GD LCIE 02 TEX 003U LCIE 02 TEX 003U FED.L FED.L th..5 th..5 FED2.L th. 4 FED2.L th. 4 BJDL5.2 () 2 poles BJDL5.3 () 3 poles BJDL5.4 () 4 poles BJDL5.5 () 5 poles BJDL5.6 () 6 poles BJDL5.7 () 7 poles BJDL5.8 () 8 poles BJDL5.9 () 9 poles BJDL5.0 () 0 poles BJDL0.2 (2) 2 poles BJDL0.3 (2) 3 poles BJDL0.4 (2) 4 poles BJDL0.5 (2) 5 poles SN 29 30 R0200 SN 29 302 R0300 SN 29 3 R2300 SN 29 32 R2400 SN 29 02 R2300 SN 29 03 R2400 SN 29 04 R2500 SN 29 05 R2600 SN 29 06 R2700 SN 29 07 R2000 SN 29 08 R000 SN 29 09 R0200 SN 29 0 R2600 SN 29 322 R2600 SN 29 323 R2700 SN 29 324 R2000 SN 29 325 R200 FEDB.L FEDB.L FED2.L FED2.L BJDL5.2 () BJDL5.3 () BJDL5.4 () BJDL5.5 () BJDL5.6 () BJDL5.7 () BJDL5.8 () BJDL5.9 () BJDL5.0 () th. 4 th. 4 2 poles 3 poles 4 poles 5 poles 6 poles 7 poles 8 poles 9 poles 0 poles SN 290 28 R000 SN 290 282 R0200 SN 29 3 R2300 SN 29 32 R2400 SN 29 02 R2300 SN 29 03 R2400 SN 29 04 R2500 SN 29 05 R2600 SN 29 06 R2700 SN 29 07 R2000 SN 29 08 R000 SN 29 09 R0200 SN 29 0 R2600 4 5 R R See markers section Other accessories see section accessories RC55 () For D...2,5/5.2L.Ex only. (2) For DR 2,5/0.P.4L.Ex only. RC55 29

T07092 Terminal blocks Insulation displacement D 2,5/5.DO.Ex Spacing 5 mm.200" D 4/6.DO.Ex Spacing 6 mm.238" D 6/8.DO.Ex Spacing 8 mm.35" Screw clamp - DO DIN 3 Exe and Exi voltage ratings apply to terminal blocks only without any accessory. The use of ground terminal blocks do not decrease the standard terminal blocks' voltage ratings. 2 wires max. same gage and nature per DO connection. Standard 5 mm block D 2,5/5.P.DO.Ex Standard 6 mm block D 4/6.P.DO.Ex Standard 8 mm block - * Black marking D 6/8.P.DO.Ex For the terminal block voltage rating with its accessories, consult our "TEX technical instructions sheet for safe mounting". Spacing 5 mm.200" Spacing 6 mm.238" Spacing 8 mm.35" 50 * 56 48,5 End stop th. 9 mm BDL V0 End stop th. 9, mm BM2 V0 Rail 35 x 7,5 x PR3.Z2 Rail 35 x 5 x 2,3 PR4 Rail 35 x 5 x,5 PR5 Standard blocks UL 94 V0 Blue body SN 399 903 R0200 SN 296 35 R0000 SN 74 300 R700 SN 68 500 R200 SN 68 700 R2200 Terminal block for ground wire with rail contact Terminal block for ground wire with rail contact Terminal block for ground wire with rail contact - * Black marking D 2,5/5.DO.Ex D 2,5/5.N.DO.Ex SN 46 07 R2400 SN 46 072 R2500 D 4/6.DO.Ex D 4/6.N.DO.Ex SN 46 032 R500 SN 46 033 R600 center of rail D 6/8.DO.Ex D 6/8.N.DO.Ex 25 SN 46 034 R700 SN 46 035 R000 Terminal blocks for ground wires UL 94 V0 Green/yellow body (with rail contact) Wire size Screw DO Short-circuit current (for ground blocks) / s Wire stripping length Recommended torque Nm / Ib.in Voltage EN 60079-7 ; EN 50020 TEX marking TEX certificate ccessories End section grey yellow 2 Circuit separator grey D 2,5/5.P.DO.Ex SN 46 074 R2700 D 4/6.P.DO.Ex 0.2-4 0.2-4 0.22-2.5 0.22-4 0.2-0.28 -.5 0.22-0.34 -.5 mm 2.5 mm 2 20 / s 80 / s 9.5 mm /.37" 0.4-0.6 Nm / 3.5-5.3 lb.in Exe : 750 V Exi : 60 V Exe : 550 V 3,5 I M2 / M II 2GD / GD LCIE 02 TEX 0029U FEDD FEDD SCD5 th. 3 th. 3 SN 99 336 R2000 SN 99 339 R0300 SN 99 55 R2000 Exi : 90 V 7,5 I M2 / M II 2GD / GD LCIE 02 TEX 0020U / 002U FEDD FEDD SCD 9.5 mm /.37" 0.5-0.8 Nm / 4.4-7. lb.in th. 3 th. 3 SN 46 03 R400 D 6/8.P.DO.Ex 0.2-0 0.22-6 - 2.5-2.5 2.5 mm 2 SN 99 336 R2000 SN 99 339 R0300 SN 96 896 R0000 300 / s 2 mm /.47" 0.8- Nm / 7.-8.9 lb.in Exe : 550 V Exi : 90 V 24 I M2 / M II 2GD / GD LCIE 02 TEX 0020U / 002U FEDD FEDD SCD th. 3 th. 3 SN 46 042 R2700 SN 99 336 R2000 SN 99 339 R0300 SN 96 896 R0000 2 7 6 6 ssembled jumper bar (without IP20 protection) 7 ssembled jumper bar (with IP20 protection) 8 Jumper bar not assembled BJM () BJMI () BJS () BJM () BJMI () BJS () BJM () BJMI () BJS () 3 2 8 0 4 5 6 7 8 0 Jumper bar Screwless jumper bar to be inserted into DO jaw orange IP20 2 Pivoting jumper bar 3 Connector plate 4 Comb-type jumper bar Isolating cover 5 Shielding connector th. 0,5 th. 0,8 6 Protection label Screw for protection label 7 IDC jumper 8 Manual tool 9 Semi-automatic tool 20 Interchangeable head kit BJB BJDO PC5 EIP CBM5 CBM8 OUMD OUPD OUT 0 poles SN 3 544 R200 SN 3 550 R2400 SN 78 745 R400 SN 78 746 R500 SN 79 466 R0600 SN 78 944 R0400 SN 205 284 R0300 BJB BJDO BJP6 EL6 PC6 EIP CBM5 CBM8 EP6 VSP6 D2,5 OUMD OUPD OUT 0 poles 4 blocks SN 74 43 R400 SN 73 627 R200 SN 3 548 R2600 SN 3 550 R2400 SN 78 745 R400 SN 78 746 R500 SN 63 427 R700 SN 63 433 R500 SN 4 205 R2000 SN 79 466 R0600 SN 78 944 R0400 SN 205 284 R0300 BJB BJDO BJP8 EL6 PC8 EP6 EP8 VSP6 D2,5 OUMD OUPD OUT 3 blocks 4 blocks SN 74 448 R0700 SN 73 627 R200 0 pôles SN 63 33 R2400 SN 63 427 R700 SN 63 428 R2000 SN 63 433 R500 SN 4 205 R2000 SN 79 466 R0600 SN 78 944 R0400 SN 205 284 R0300 20 9 R See markers section These accessories cannot be These accessories cannot be mounted on D 2,5/5.P.DO.Ex mounted on D 4/6.P.DO.Ex block block RC55 - RC50 - RTM 7 RC65 - RC60 - RTM7 () circuit separator SC... is required with these accessories. These accessories cannot be mounted on D 6/8.P.DO.Ex block RCL85 - RC80 - RTM7 30

T07093 Terminal blocks Insulation displacement Screw clamp - DO DIN 3 D 6/8.DO3.Ex Spacing 8 mm.35" Exe and Exi voltage ratings apply to terminal blocks only without any accessory. The use of ground terminal blocks do not decrease the standard terminal blocks' voltage ratings. Only wire per DO connection. For the terminal block voltage rating with its accessories, consult our "TEX technical instructions sheet for safe mounting". Standard 8 mm block - * White marking D 6/8.P.DO3.Ex Spacing 8 mm.35" End stop th. 9 mm BDL V0 End stop th. 9, mm BM2 V0 Rail 35 x 7,5 x PR3.Z2 Rail 35 x 5 x 2,3 PR4 Rail 35 x 5 x,5 PR5 Standard blocks UL 94 V0 Blue body SN 399 903 R0200 SN 296 35 R0000 SN 74 300 R700 SN 68 500 R200 SN 68 700 R2200 Terminal block for ground wire with rail contact - * White marking D 6/8.DO3.Ex D 6/8.N.DO3.Ex SN 46 078 R0300 SN 46 079 R0400 Terminal blocks for ground wires UL 94 V0 2 Green/yellow body (with rail contact) Wire size Screw DO Short-circuit current (for ground blocks) / s Wire stripping length Recommended torque Nm / Ib.in Voltage EN 60079-7 ; EN 50020 TEX marking TEX certificate ccessories End section grey yellow 2 Circuit separator grey D 6/8.P.DO3.Ex SN 46 08 R700 0.2-0 0.22-6 4 4 4 mm 2 480 / s 2 mm /.47" 0.8- Nm / 7.-8.9 lb.in Exe : 750 V Exi : 375 V 32 I M2 / M II 2GD / GD LCIE 02 TEX 0029U FEDD FEDD SCD th. 3 th. 3 SN 99 336 R2000 SN 99 339 R0300 SN 96 896 R0000 7 6 8 6 ssembled jumper bar (without IP20 protection) 7 ssembled jumper bar (with IP20 protection) 8 Jumper bar not assembled BJM8 () BJMI8 () BJS () 6 2 3 0 4 5 7 0 Jumper bar Screwless jumper bar to be inserted into DO jaw orange IP20 2 Pivoting jumper bar 3 Connector plate 4 Comb-type jumper bar 5 Protection label Screw for protection label 6 IDC jumper 7 Manual tool 8 Semi-automatic tool 9 Interchangeable head kit BJB BJDO BJP8 EL6 PC8 EP6 EP8 VSP6 D2,5 OUMD OUPD OUT 0 poles 3 blocks 4 blocks SN 74 448 R0700 SN 73 627 R200 SN 63 33 R2400 SN 63 427 R700 SN 63 428 R2000 SN 63 433 R500 SN 4 205 R2000 SN 79 466 R0600 SN 78 944 R0400 SN 205 284 R0300 9 8 R See markers section These accessories cannot be mounted on D 6/8.P.DO3.Ex block RCL85 - RC80 - RTM7 () circuit separator SC... is required with these accessories. 3

T07094 Double deck terminal blocks Insulation displacement Screw clamp - DO DIN 3 D 4/6.D2.DO.Ex Spacing 6 mm.238" Exe and Exi voltage ratings apply to terminal blocks only without any accessory. The use of ground terminal blocks do not decrease the standard terminal blocks' voltage ratings. 2 wires max. same gage and nature per DO connection. For the terminal block voltage rating with its accessories, consult our "TEX technical instructions sheet for safe mounting". End stop th. 2 mm BDH V2 End stop th. 9, mm BMH V0 V0 Rail 35 x 7,5 x PR3.Z2 Rail 35 x 5 x 2,3 PR4 Rail 35 x 5 x,5 PR5 SN 6 900 R2700 SN 94 836 R000 SN 74 300 R700 SN 68 500 R200 SN 68 700 R2200 Terminal block 6 mm, double deck opened. Standard blocks UL 94 V0 Blue body D 4/6.D2.DO.Ex D 4/6.D2.N.DO.Ex SN 46 045 R2200 SN 46 046 R2300 Wire size Screw DO Wire stripping length Recommended torque Nm / Ib.in Voltage EN 60079-7 ; EN 50020 TEX marking TEX certificate ccessories 3 2 End section grey 2 Circuit separator grey 3 Test socket DI. 2 mm DI. 3 mm 0.2-4 0.22-4 0.28 -.5 0.34 -.5.5 mm 2 9.5 mm /.37" 0.5-0.8 Nm / 4.4-7. lb.in Exe : 550 V Exi : 375 V 7.5 I M2 / M II 2GD / GD LCIE 02 TEX 002U FED2D SCD L2 () L3 () th. 5 SN 99 47 R200 SN 96 896 R0000 DI 2 SN 63 043 R200 DI 3 SN 63 26 R0000 6 7 6 ssembled jumper bar without IP20 protection 7 ssembled jumper bar with IP20 protection 8 Jumper bar not assembled Post + washer + captive screw IP20 BJM6... BJMI6... BJS6 EV6I 20 poles SN 74 784 R2000 SN 206 394 R0200 8 2 5 7 9 0 3 4 6 8 0 Connector plate Screwless jumper bar to be inserted into DO jaw orange IP20 2 Pivoting jumper bar 3 Jumper bar for alternated jumping 4 Connector plate 5 Comb-type jumper bar Isolating cover 6 Vertical jumper bar 7 Shielding connector 8 Protection label Screw for protection label 9 IDC jumper 20 Manual tool 2 Semi-automatic tool 22 Interchangeable head kit BJB BJDO6... BJP6 () BJ6 () EL6 PC6 EIP ITVE CBD2S EP6 VSP6 D2,5 OUMD OUPD OUT 0 poles 0 poles 4 blocks SN 99 466 R2300 SN 74 43 R400 SN 6 54 R200 SN 73 627 R200 SN 3 548 R2600 SN 3 550 R2400 SN 79 694 R0300 SN 78 408 R400 SN 63 427 R700 SN 63 433 R500 SN 4 205 R2000 SN 79 466 R0600 SN 78 944 R0400 SN 205 284 R0300 20 2 22 R R See markers section RC65 - RC60 - RTM7 () circuit separator SC... is required with these accessories. 32

T07095 Terminal blocks Insulation displacement D /5.DO.Ex Spacing 5 mm.200" D,5/6.DO.Ex Spacing 6 mm.238" DO - DO DIN 3 Exe and Exi voltage ratings apply to terminal blocks only without any accessory. The use of ground terminal blocks do not decrease the standard terminal blocks' voltage ratings. 2 wires max. same gage and nature per DO connection. Standard 5 mm block D /5.P.DO.Ex Standard 6 mm block D,5/6.P.DO.Ex For the terminal block voltage rating with its accessories, consult our "TEX technical instructions sheet for safe mounting". Spacing 5 mm.200" Spacing 6 mm.238" End stop th. 9 mm BDL V0 End stop th. 9, mm BM2 V0 Rail 35 x 7,5 x PR3.Z2 Rail 35 x 5 x 2,3 PR4 Rail 35 x 5 x,5 PR5 Standard blocks UL 94 V0 Blue body SN 399 903 R0200 SN 296 35 R0000 SN 74 300 R700 SN 68 500 R200 SN 68 700 R2200 Terminal block for ground wire with rail contact D /5.DO.Ex D /5.N.DO.Ex SN 46 069 R0200 SN 46 070 R0700 Terminal block for ground wire with rail contact D,5/6.DO.Ex D,5/6.N.DO.Ex SN 46 036 R00 SN 46 037 R200 Terminal blocks for ground wires UL 94 V0 Green/yellow body (with rail contact) Wire size Screw DO Short-circuit current (for ground blocks) / s Wire stripping length Recommended torque Nm / Ib.in Voltage EN 60079-7 ; EN 50020 TEX marking TEX certificate ccessories End section grey yellow 2 Circuit separator grey D /5.P.DO.Ex 0.2-0.22 - mm 2 20 / s FEMD3 FEMD3 SCD5 0.34 -.5 0.34 -.5.5 mm 2 80 / s Exe : 750 V Exi : 60 V Exe : 550 V Exi : 90 V 3,5 I M2 / M II 2GD / GD 7,5 I M2 / M II 2GD / GD LCIE 02 TEX 0029U LCIE 02 TEX 002U th. 3 th. 3 SN 46 075 R2000 D,5/6.P.DO.Ex SN 99 34 R0500 SN 99 343 R0700 SN 99 55 R2000 FEMD3 FEMD3 SCD th. 3 th. 3 SN 46 040 R000 SN 99 34 R0500 SN 99 343 R0700 SN 99 55 R2000 2 6 8 0 9 5 7 5 ssembled jumper bar (without IP20 protection) 6 ssembled jumper bar (with IP20 protection) 7 Jumper bar not assembled Post + screw + washer 8 Jumper bar not assembled Post + washer + captive screw IP20 9 Jumper bar 0 Screwless jumper bar to be inserted into DO jaw orange IP20 Pivoting jumper bar 2 Connector plate 3 Shielding connector th. 0,5 th. 0,8 4 Protection label BJM5 () BJMI5 () BJS5 () EV5 BJB BJDO5... CBM5 CBM8 SN 78 745 R400 SN 78 746 R500 BJM6 () BJMI6 () BJS6 () EV6I BJB BJDO6... BJP6 EL6 CBM5 CBM8 EP6 SN 74 43 R400 SN 73 627 R200 SN 78 745 R400 SN 78 746 R500 SN 63 427 R700 4 2 3 Screw for protection label 5 Manual tool 6 Semi-automatic tool 7 Interchangeable head kit OUMD OUPD OUT SN 79 466 R0600 SN 78 944 R0400 SN 205 284 R0300 VSP6 OUMD OUPD OUT SN 63 433 R500 SN 79 466 R0600 SN 78 944 R0400 SN 205 284 R0300 5 6 7 R See markers section RC55 - RC50 - RTM 7 RC65 - RC60 - RTM7 () circuit separator SC... is required with these accessories. 33

T07096 Terminal blocks Insulation displacement D 2,5/8.DO.Ex Spacing 8 mm.35" D 4/8.DO.Ex Spacing 8 mm.35" DO - DO DIN 3 Exe and Exi voltage ratings apply to terminal blocks only without any accessory. The use of ground terminal blocks do not decrease the standard terminal blocks' voltage ratings. 2 wires max. same gage and nature per DO connection. Standard 8 mm block - * Black marking D 2,5/8.P.DO.Ex Standard 8 mm block - * White marking D 4/8.P.DO.Ex For the terminal block voltage rating with its accessories, consult our "TEX technical instructions sheet for safe mounting". Spacing 8 mm.35" Spacing 8 mm.35" End stop th. 9 mm BDL V0 End stop th. 9, mm BM2 V0 Rail 35 x 7,5 x PR3.Z2 Rail 35 x 5 x 2,3 PR4 Rail 35 x 5 x,5 PR5 Standard blocks UL 94 V0 Blue body SN 399 903 R0200 SN 296 35 R0000 SN 74 300 R700 SN 68 500 R200 SN 68 700 R2200 Terminal block for ground wire with rail contact - * Black marking Terminal block for ground wire with rail contact - * White marking D 2,5/8.DO.Ex D 2,5/8.N.DO.Ex SN 46 038 R2300 SN 46 039 R2400 D 4/8.DO.Ex D 4/8.N.DO.Ex SN 46 076 R200 SN 46 077 R2200 Terminal blocks for ground wires UL 94 V0 ccessories Green/yellow body (with rail contact) Wire size Screw DO Short-circuit current (for ground blocks) / s Wire stripping length Recommended torque Nm / Ib.in Voltage EN 60079-7 ; EN 50020 TEX marking TEX certificate End section grey 2 Circuit separator grey D 2,5/8.P.DO.Ex - 2.5-2.5 2.5 mm 2 300 / s SN 46 04 R2600 D 4/8.P.DO.Ex 2.5-4 4 4 mm 2 480 / s SN 46 080 R2200 Exe : 420 V Exi : 90 V Exe : 420 V Exi : 90 V 24 32 I M2 / M II 2GD / GD I M2 / M II 2GD / GD LCIE 02 TEX 002U LCIE 02 TEX 0029U FEMD3 SCD th. 3 SN 99 34 R0500 SN 96 896 R0000 FEMD3 SCD th. 3 SN 99 34 R0500 SN 96 896 R0000 2 5 6 9 0 7 5 ssembled jumper bar (without IP20 protection) 6 ssembled jumper bar (with IP20 protection) 7 Jumper bar not assembled Post + washer + captive screw IP20 9 Jumper bar 0 Pivoting jumper bar Connector plate 2 Protection label Screw for protection label 3 Manual tool 4 Semi-automatic tool 5 Interchangeable head kit BJM8 () BJMI8 () BJS8 () EV6I BJB BJP8 EL6 EP6 EP8 VSP6 OUMD OUPD OUT SN 99 466 R2300 SN 74 448 R0700 SN 73 627 R200 SN 63 427 R700 SN 63 428 R2000 SN 63 433 R500 SN 79 466 R0600 SN 78 944 R0400 SN 205 284 R0300 BJM8 () BJMI8 () BJS8 () EV6I BJB BJP8 EL6 EP6 EP8 VSP6 OUMD OUPD OUT SN 99 466 R2300 SN 74 448 R0700 SN 73 627 R200 SN 63 427 R700 SN 63 428 R2000 SN 63 433 R500 SN 79 466 R0600 SN 78 944 R0400 SN 205 284 R0300 2 4 3 5 R R See markers section RCL85 - RC60 - RTM7 RCL85 - RC60 - RTM7 () circuit separator SC... is required with these accessories. 34

T07097 Double deck terminal blocks Insulation displacement DO - DO DIN 3 D,5/6.D2.DO.Ex Spacing 6 mm.238" Exe and Exi voltage ratings apply to terminal blocks only without any accessory. The use of ground terminal blocks do not decrease the standard terminal blocks' voltage ratings. 2 wires max. same gage and nature per DO connection. For the terminal block voltage rating with its accessories, consult our "TEX technical instructions sheet for safe mounting". End stop th. 2 mm BDH V2 End stop th. 9, mm BMH V0 V0 Rail 35 x 7,5 x PR3.Z2 Rail 35 x 5 x 2,3 PR4 Rail 35 x 5 x,5 PR5 SN 6 900 R2700 SN 94 836 R000 SN 74 300 R700 SN 68 500 R200 SN 68 700 R2200 Terminal block 6 mm, double deck opened. Standard blocks UL 94 V0 Blue body D,5/6.D2.DO.Ex D,5/6.D2.N.DO.Ex SN 46 062 R2300 SN 46 063 R2400 Wire size Screw DO Wire stripping length Recommended torque Nm / Ib.in Voltage EN 60079-7 ; EN 50020 TEX marking TEX certificate ccessories End section grey 2 Circuit separator grey 0.28 -.5 0.34 -.5.5 mm 2 Exe : 550 V Exi : 375 V 7.5 I M2 / M II 2GD / GD LCIE 02 TEX 0029U FED2D2 SCD th. 5 SN 99 476 R2500 SN 96 896 R0000 2 6 5 7 9 0 2 3 4 5 ssembled jumper bar without IP20 6 ssembled jumper bar with IP20 7 Jumper bar not assembled Post + washer + captive screw IP20 9 Jumper bar 0 Svrewless jumper bar to be inserted into DO jaw orange IP20 Pivoting jumper bar 2 Jumper bar for alternated jumping 3 Connector plate 4 Vertical jumper bar 5 Shielding connector 6 Protection label Screw for protection label 7 Manual tool 8 Semi-automatic tool 9 Interchangeable head kit BJM6 BJMI6 BJS6 EV6I BJB BJDO6... BJP6 BJ6 EL6 ITVE CBD2S EP6 VSP6 OUMD OUPD OUT 20 poles SN 74 784 R2000 SN 206 394 R0200 0 poles 4 blocks SN 99 466 R2300 SN 74 43 R400 SN 6 54 R200 SN 73 627 R200 SN 79 694 R0300 SN 78 408 R400 SN 63 427 R700 SN 63 433 R500 SN 79 466 R0600 SN 78 944 R0400 SN 205 284 R0300 5 6 7 8 9 R R See markers section RC65 - RC60 - RTM7 () circuit separator SC... is required with these accessories. 35

T07098 Standard and ground miniblocks - Screw clamp - DO DIN 2 / DIN 3 / Base mount DR... 4/6.DO.Ex Spacing 6 mm.238" Mounting rail DIN 2 DS 4/6... DO.Ex Spacing 6 mm.238" Mounting rail DIN 3 DB 4/6.DO.Ex Spacing 6 mm.238" Base mount with flanges Exe and Exi voltage ratings apply to terminal blocks only without any accessory. The use of ground terminal blocks do not decrease the standard terminal blocks' voltage ratings. 2 wires max. same gage and nature per DO connection. For the terminal block voltage rating with its accessories, consult our "TEX technical instructions sheet for safe mounting". DR 4/6.PI.DO.Ex Spacing 6 mm.238" Mounting rail DIN 2 End stop th. 6.5 mm BDRL V0 End stop th. 2 mm BDH V2 End stop th. 9, mm BMH V0 V0 Rail 5 x 5 x PR2 Rail 35 x 7,5 x PR3.Z2 Rail 35 x 5 x 2,3 PR4 Rail 35 x 5 x,5 PR5 SN 99 420 R200 SN 6 900 R2700 SN 94 836 R000 SN 64 600 R200 SN 74 300 R700 SN 68 500 R200 SN 68 700 R2200 Standard blocks UL 94 V0 Orange body (without rib) Blue body Terminal blocks for Yellow body/green (without rail contact) ground wires UL 94 V0 Wire size Screw DO Short-circuit current (for ground blocks) / s Wire stripping length Recommended torque Nm / Ib.in Voltage EN 60079-7 ; EN 50020 TEX marking TEX certificate ccessories 3 5 8 2 6 4 7 End stop (DIN 2) grey 2 End stop (DIN 3) grey 3 End section grey orange 4 End section kit with grey screw locks (right + left) orange 5 Separator grey orange 6 Test device 7 Test plug 8 Screwless jumper bar to be inserted into DO jaw orange IP20 9 Comb-type jumper bar InsulatinG 0 IDC jumper Manual tool 2 Semi-automatic tool 3 Interchangeable head kit 4 Pneumatic tool kit 5 Extraction tool kit DR 4/6.DO.Ex DR 4/6.DO.Ex DRE 4/6.DO.Ex DR 4/6.PI.DO.Ex BDRL V0 FED V0 FED V0 FED5 V0 FED5 V0 DCJ FC2 BJDO6... PC6 EIP OUMD OUPD OUT OUTD EXD2 SN 46 202 R0500 DS 4/6.DO.Ex SN 46 208 R300 SN 46 209 R400 DS 4/6.N.DO.Ex SN 46 203 R0600 BDL V0 FED V0 FED V0 FED5 V0 FED5 V0 DCJ FC2 BJDO6... PC6 EIP D2,5 V2 OUMD OUPD OUT OUTD EXD2 DB 4/6.DO.Ex 0.2-4 0.2-4 0.2-4 0.22-4 0.22-4 0.22-4 0.28 -.5 0.28 -.5 0.28 -.5 0.34 -.5 0.34 -.5 0.34 -.5.5 mm 2.5 mm 2.5 mm 2 80 / s 9.5 mm /.37" 9.5 mm /.37" 9.5 mm /.37" 0,5-0,8 Nm / 4,4-7, Ib-in 0,5-0,8 Nm / 4,4-7, Ib-in 0,5-0,8 Nm / 4,4-7, Ib-in Exe : 420 V Exi : 90 V Exe : 420 V Exi : 90 V Exe : 420 V Exi : 90 V 7,5 I M2 / M II 2GD / GD 7,5 I M2 / M II 2GD / GD 7,5 I M2 / M II 2GD / GD LCIE 02 TEX 0032U LCIE 02 TEX 0032U LCIE 02 TEX 0032U th. 6.5 th. 2.5 th. 2.5 th. 5.0 th. 5.0 SN 99 420 R200 SN 99 42 R600 SN 99 422 R700 SN 99 433 R200 SN 99 434 R300 SN 73 059 R0300 DI. 2 SN 007 865 R2600 SN 3 550 R2400 SN 79 466 R0600 SN 78 944 R0400 SN 205 284 R0300 SN 205 70 R00 SN 205 72 R0000 th. 9.0 th. 2.5 th. 2.5 th. 5.0 th. 5.0 SN 46 064 R2500 SN 46 065 R2600 SN 399 903 R0200 SN 99 42 R600 SN 99 422 R700 SN 99 433 R200 SN 99 434 R300 SN 73 059 R0300 DI. 2 SN 007 865 R2600 SN 3 550 R2400 SN 4 205 R2000 SN 79 466 R0600 SN 78 944 R0400 SN 205 284 R0300 SN 205 70 R00 SN 205 72 R0000 FED3 V0 FED3 V0 FED5 V0 FED5 V0 DCJ V2 FC2 BJDO6... PC6 EIP D2,5 V2 OUMD OUPD OUT OUTD EXD2 th. 5.0 th. 5.0 SN 46 20 R0000 SN 99 437 R600 SN 99 438 R2700 SN 99 433 R200 SN 99 434 R300 SN 73 059 R0300 DI. 2 SN 007 865 R2600 SN 3 550 R2400 SN 4 205 R2000 SN 79 466 R0600 SN 78 944 R0400 SN 205 284 R0300 SN 205 70 R00 SN 205 72 R0000 9 0 2 3 4 5 R R See markers section Top of block RC65 - RCL85 Top of block RC65 - RCL85 Top of block RC65 - RCL85 36

T07099 Standard and ground miniblocks - Screw clamp - DO DIN 2 DR 4/8.DO.Ex Spacing 8 mm.35" Mounting rail DIN 2 Exe and Exi voltage ratings apply to terminal blocks only without any accessory. The use of ground terminal blocks do not decrease the standard terminal blocks' voltage ratings. 2 wires max. same gage and nature per DO connection. For the terminal block voltage rating with its accessories, consult our "TEX technical instructions sheet for safe mounting". DR 4/8.PI.DO.Ex Spacing 8 mm.35" Mounting rail DIN 2 End stop th. 6.5 mm BDRL V0 Rail 5 x 5 x PR2 SN 99 420 R200 SN 64 600 R200 Standard blocks UL 94 V0 DR 4/8.DO.Ex SN 46 255 R000 Terminal blocks for ground wires UL 94 V0 ccessories 2 Yellow body/green (without rail contact) Wire size Screw DO Short-circuit current (for ground blocks) / s Wire stripping length Recommended torque Nm / Ib.in Voltage EN 60079-7 ; EN 50020 TEX marking TEX certificate End stop (DIN 2) grey 2 End section grey orange 3 Separator grey orange DR 4/8.PI.DO.Ex 0.2-4 0.22-4 - 2.5-2.5 2.5 mm 2 300 / s 9.5 mm /.37" 0,5-0,8 Nm / 4,4-7, Ib-in Exe : 550 V Exi : 375 V 24 I M2 / M II 2GD / GD LCIE 02 TEX 0032U BDRL V0 FED V0 FED V0 FED5 V0 FED5 V0 th. 6.5 th. 2.5 th. 2.5 th. 5.0 th. 5.0 SN 46 204 R0700 SN 99 420 R200 SN 99 42 R600 SN 99 422 R700 SN 99 433 R200 SN 99 434 R300 3 6 Comb-type jumper bar 7 IDC jumper 8 Manual tool 9 Semi-automatic tool 0 Interchangeable head kit Pneumatic tool kit 2 Extraction tool kit PC8 D2,5 V2 OUMD OUPD OUT OUTD EXD2 SN 4 205 R2000 SN 79 466 R0600 SN 78 944 R0400 SN 205 284 R0300 SN 205 70 R00 SN 205 72 R0000 6 7 8 9 0 2 R R See markers section Top of block RCL85 37

T0709 Standard and ground miniblocks - DO - DO DIN 2 / DIN 3 DR,5/6.DO.Ex Spacing 6 mm.238" Mounting rail DIN 2 DS,5/6... DO.Ex Spacing 6 mm.238" Mounting rail DIN 3 Exe and Exi voltage ratings apply to terminal blocks only without any accessory. The use of ground terminal blocks do not decrease the standard terminal blocks' voltage ratings. 2 wires max. same gage and nature per DO connection. For the terminal block voltage rating with its accessories, consult our "TEX technical instructions sheet for safe mounting". End stop th. 6.5 mm BDRL V0 End stop th. 2 mm BDH V2 End stop th. 9, mm BMH V0 V0 Rail 5 x 5 x PR2 Rail 35 x 7,5 x PR3.Z2 Rail 35 x 5 x 2,3 PR4 Rail 35 x 5 x,5 PR5 SN 99 420 R200 SN 6 900 R2700 SN 94 836 R000 SN 64 600 R200 SN 74 300 R700 SN 68 500 R200 SN 68 700 R2200 DR,5/6.PI.DO.Ex Spacing 6 mm.238" Mounting rail DIN 2 Standard blocks UL 94 V0 Blue body DR,5/6.DO.Ex SN 46 205 R0000 DS,5/6.DO.Ex DS,5/6.N.DO.Ex SN 46 066 R2700 SN 46 067 R2000 Terminal blocks for ground wires UL 94 V0 ccessories 2 3 4 Yellow body/green (without rail contact) Wire size Screw DO Short-circuit current (for ground blocks) / s Wire stripping length Recommended torque Nm / Ib.in Voltage EN 60079-7 ; EN 50020 TEX marking TEX certificate End stop (DIN 2) grey 2 End stop (DIN 3) grey 3 End section grey orange 4 Separator grey orange 5 Screwless jumper bar to be inserted into DO jaw orange IP20 6 Manual tool 7 Semi-automatic tool 8 Interchangeable head kit 9 Pneumatic tool kit 0 Extraction tool kit DR,5/6.PI.DO.Ex BDRL V0 FED2 V0 FED2 V0 FED6 V0 FED6 V0 BJDO6... OUMD OUPD OUT OUTD EXD2 0.28 -.5 0.34 -.5.5 mm 2 80 / s BDL V0 FED2 V0 FED2 V0 FED6 V0 FED6 V0 BJDO6... OUMD OUPD OUT OUTD EXD2 0.28 -.5 0.34 -.5.5 mm 2 Exe : 550 V Exi : 375 V Exe : 550 V Exi : 375 V 7,5 I M2 / M II 2G / G 7,5 I M2 / M II 2GD / GD LCIE 02 TEX 0032U LCIE 02 TEX 0032U th. 6.5 th. 2.5 th. 2.5 th. 5.0 th. 5.0 SN 46 206 R000 SN 99 420 R200 SN 99 423 R000 SN 99 424 R00 SN 99 435 R400 SN 99 436 R500 SN 79 466 R0600 SN 78 944 R0400 SN 205 284 R0300 SN 205 70 R00 SN 205 72 R0000 th. 9.0 th. 2.5 th. 2.5 th. 5.0 th. 5.0 SN 399 903 R0200 SN 99 423 R000 SN 99 424 R00 SN 99 435 R400 SN 99 436 R500 SN 79 466 R0600 SN 78 944 R0400 SN 205 284 R0300 SN 205 70 R00 SN 205 72 R0000 5 6 8 7 9 0 R R See markers section Top of block RC65 - RCL85 Top of block RC65 - RCL85 38

T0709 Numerical and alphabetical index SN 007 865 R2600 36 SN 03 002 R2600 26 SN 03 06 R2000 6 SN 03 065 R2400 5 SN 03 25 R500 4 SN 03 26 R600 4 SN 03 775 R0000 8 SN 03 776 R000 8 SN 3 003 R000 4 SN 3 02 R000 5 SN 3 482 R0500 7 SN 3 544 R200 4 SN 3 548 R2600 4 SN 3 550 R2400 4 SN 3 85 R600 6 SN 4 205 R2000 8 SN 4 825 R0500 4 SN 6 54 R200 32 SN 6 720 R200 7 SN 6 728 R2500 4 SN 6 77 R2000 8 SN 6 900 R2700 6 SN 6 934 R0400 6 SN 8 495 R700 7 SN 8 707 R0300 4 SN 26 576 R700 4 SN 26 629 R2400 4 SN 27 600 R0500 24 SN 28 499 R2500 7 SN 28 68 R0300 5 SN 46 00 R2700 4 SN 46 002 R2000 4 SN 46 003 R200 5 SN 46 004 R2200 5 SN 46 005 R2300 5 SN 46 006 R2400 5 SN 46 009 R0700 7 SN 46 00 R2300 4 SN 46 0 R000 4 SN 46 02 R00 4 SN 46 03 R200 4 SN 46 04 R300 4 SN 46 05 R400 4 SN 46 06 R500 4 SN 46 07 R600 7 SN 46 08 R2700 7 SN 46 09 R2000 7 SN 46 020 R2500 6 SN 46 02 R200 5 SN 46 022 R300 5 SN 46 023 R400 4 SN 46 024 R500 6 SN 46 025 R600 6 SN 46 026 R700 6 SN 46 027 R000 5 SN 46 028 R200 5 SN 46 029 R2200 6 SN 46 030 R2700 6 SN 46 03 R400 30 SN 46 032 R500 30 SN 46 033 R600 30 SN 46 034 R700 30 SN 46 035 R000 30 SN 46 036 R00 33 SN 46 037 R200 33 SN 46 038 R2300 34 SN 46 039 R2400 34 SN 46 040 R000 33 SN 46 04 R2600 34 SN 46 042 R2700 30 SN 46 043 R2000 5 SN 46 044 R200 6 SN 46 045 R2200 32 SN 46 046 R2300 32 SN 46 047 R2400 27 SN 46 048 R0500 27 SN 46 049 R0600 25 SN 46 050 R0300 25 SN 46 05 R2000 25 SN 46 052 R200 25 SN 46 053 R2200 25 SN 46 054 R2300 25 SN 46 055 R2400 25 SN 46 056 R2500 25 SN 46 057 R2600 25 SN 46 058 R0700 27 SN 46 059 R0000 27 SN 46 060 R0500 27 SN 46 06 R2200 27 SN 46 062 R2300 35 SN 46 063 R2400 35 SN 46 064 R2500 36 SN 46 065 R2600 36 SN 46 066 R2700 38 SN 46 067 R2000 38 SN 46 068 R000 6 SN 46 069 R0200 33 SN 46 070 R0700 33 SN 46 07 R2400 30 SN 46 072 R2500 30 SN 46 073 R2600 6 SN 46 074 R2700 30 SN 46 075 R2000 33 SN 46 076 R200 34 SN 46 077 R2200 34 SN 46 078 R0300 3 SN 46 079 R0400 3 SN 46 080 R2200 34 SN 46 08 R700 3 SN 46 098 R2000 8 SN 46 04 R2300 8 SN 46 8 R2000 28 SN 46 20 R2600 28 SN 46 22 R400 28 SN 46 30 R2000 28 SN 46 32 R600 28 SN 46 34 R000 28 SN 46 38 R2400 28 SN 46 40 R0200 28 SN 46 99 R2200 24 SN 46 200 R700 24 SN 46 20 R0400 24 SN 46 202 R0500 36 SN 46 203 R0600 36 SN 46 204 R0700 37 SN 46 205 R0000 38 SN 46 206 R000 38 SN 46 207 R0200 29 SN 46 208 R300 36 SN 46 209 R400 36 SN 46 20 R0000 36 SN 46 2 R2500 9 SN 46 22 R2600 9 SN 46 227 R2500 20 SN 46 237 R2700 4 SN 46 238 R0000 5 SN 46 239 R000 5 SN 46 240 R600 4 SN 46 245 R0700 4 SN 46 246 R0000 29 SN 46 247 R000 29 SN 46 25 R0500 27 SN 46 253 R0700 27 SN 46 255 R000 37 SN 46 259 R500 4 SN 46 260 R200 7 SN 46 26 R0700 4 SN 46 262 R0000 4 SN 46 263 R000 29 SN 46 269 R700 6 SN 46 270 R400 5 SN 46 27 R000 6 SN 46 272 R0200 9 SN 46 273 R0300 9 SN 46 276 R0600 24 SN 46 277 R0700 24 SN 46 279 R00 29 SN 46 285 R2000 4 SN 46 289 R0400 6 SN 46 29 R2600 5 SN 46 293 R2000 24 SN 46 302 R000 2 SN 46 303 R0200 2 SN 46 304 R0300 2 SN 46 305 R0400 22 SN 46 306 R0500 22 SN 46 307 R0600 2 SN 46 308 R700 2 SN 46 309 R000 2 SN 46 30 R0400 22 SN 46 3 R200 22 SN 46 350 R400 9 SN 46 352 R0200 26 SN 63 043 R200 32 SN 63 050 R0400 4 SN 63 8 R00 9 SN 63 26 R0000 32 SN 63 3 R2200 7 SN 63 33 R2400 5 SN 63 35 R2600 5 SN 63 394 R2600 9 SN 63 427 R700 4 SN 63 428 R2000 5 SN 63 429 R200 5 SN 63 430 R2600 5 SN 63 43 R300 6 SN 63 432 R400 5 SN 63 433 R500 4 SN 64 573 R2200 9 SN 64 574 R2300 9 SN 64 575 R2400 9 SN 64 576 R2500 9 SN 64 58 R300 9 SN 64 582 R400 9 SN 64 583 R500 9 SN 64 584 R600 9 SN 64 585 R700 9 SN 64 586 R000 9 SN 64 587 R00 9 SN 64 588 R2200 9 SN 64 600 R200 24 SN 64 736 R2500 9 SN 64 737 R2600 9 SN 68 238 R600 6 SN 68 273 R00 9 SN 68 400 R600 7 SN 68 485 R2700 7 SN 68 500 R200 4 SN 68 56 R2500 9 SN 68 57 R2600 9 SN 68 58 R0700 9 SN 68 59 R0000 9 SN 68 520 R0500 9 SN 68 52 R2200 9 SN 68 522 R2300 9 SN 68 523 R2400 9 SN 68 629 R600 4 SN 68 664 R00 5 SN 68 700 R2200 4 SN 68 962 R0400 7 SN 68 973 R0700 9 SN 68 974 R0000 9 SN 73 06 R000 24 SN 73 059 R0300 36 SN 73 47 R2000 6 SN 73 206 R0400 24 SN 73 207 R0500 24 SN 73 27 R2600 24 SN 73 28 R0700 24 SN 73 29 R0000 24 SN 73 22 R2200 24 SN 73 223 R2400 24 SN 73 226 R2700 24 SN 73 36 R200 6 SN 73 37 R2200 6 SN 73 38 R0300 6 SN 73 39 R0400 6 SN 73 320 R000 6 SN 73 323 R2000 6 SN 73 327 R2400 6 SN 73 328 R0500 6 SN 73 33 R2000 6 SN 73 55 R00 7 SN 73 56 R200 7 SN 73 57 R300 7 SN 73 59 R2500 7 SN 73 520 R2200 7 SN 73 530 R2400 7 SN 73 627 R200 4 SN 73 888 R2000 9 SN 74 2 R600 24 SN 74 3 R700 24 SN 74 4 R000 24 SN 74 5 R00 24 SN 74 300 R700 4 SN 74 43 R400 30 SN 74 448 R0700 30 SN 74 784 R2000 4 SN 74 788 R0400 9 SN 74 789 R0500 5 SN 76 226 R2200 7 SN 76 227 R2300 7 SN 76 228 R0400 7 SN 76 229 R0500 7 SN 76 230 R0200 7 SN 76 259 R300 7 SN 76 260 R000 7 SN 76 278 R600 4 SN 76 279 R700 4 SN 76 280 R0500 4 SN 76 28 R2200 4 SN 76 282 R2300 4 SN 76 663 R0000 4 SN 76 664 R000 4 SN 76 665 R0200 4 SN 76 666 R0300 4 SN 76 667 R0400 4 SN 76 669 R600 5 SN 76 670 R300 5 SN 76 67 R0000 5 SN 76 672 R000 5 SN 76 673 R0200 5 SN 76 675 R0400 5 SN 76 676 R0500 5 SN 76 677 R0600 5 SN 76 678 R700 5 SN 76 679 R000 5 SN 76 736 R200 7 SN 76 737 R2200 7 SN 76 738 R0300 7 SN 76 739 R0400 7 SN 76 740 R00 7 SN 77 508 R0700 6 SN 77 509 R0000 6 SN 77 50 R2400 6 SN 77 5 R00 6 SN 77 65 R0500 7 SN 77 652 R0600 4 SN 77 653 R0700 5 SN 77 654 R0000 5 SN 77 82 R700 8 SN 78 024 R2500 8 SN 78 025 R2600 8 SN 78 026 R2700 8 SN 78 027 R2000 8 SN 78 032 R2500 8 SN 78 033 R2600 8 SN 78 408 R400 32 SN 78 745 R400 4 SN 78 746 R500 4 SN 78 944 R0400 30 SN 79 466 R0600 30 SN 79 63 R000 6 SN 79 64 R0200 6 SN 79 65 R0300 6 SN 79 66 R0400 6 SN 79 67 R0500 6 SN 79 626 R0600 5 SN 79 627 R0700 6 SN 79 628 R000 5 SN 79 629 R00 5 SN 79 630 R600 5 SN 79 63 R0300 5 SN 79 668 R2000 7 SN 79 669 R200 7 SN 79 670 R2600 7 SN 79 67 R300 7 SN 79 672 R400 7 SN 79 694 R0300 32 SN 90 06 R600 2 SN 90 07 R700 2 SN 90 08 R2000 2 SN 90 09 R200 22 SN 93 482 R0600 7 SN 94 836 R000 6 SN 96 896 R0000 30 SN 98 68 R0200 5 SN 99 302 R0700 4 SN 99 304 R000 6 SN 99 305 R0200 4 SN 99 306 R0300 26 SN 99 336 R2000 30 SN 99 339 R0300 30 SN 99 34 R0500 33 SN 99 343 R0700 33 SN 99 47 R200 32 SN 99 420 R200 24 SN 99 42 R600 36 SN 99 422 R700 36 SN 99 423 R000 38 SN 99 424 R00 38 SN 99 433 R200 36 SN 99 434 R300 36 SN 99 435 R400 38 SN 99 436 R500 38 SN 99 437 R600 36 SN 99 438 R2700 36 SN 99 466 R2300 32 SN 99 476 R2500 35 SN 99 55 R2000 30 SN 205 284 R0300 30 SN 205 70 R00 36 SN 205 72 R0000 36 SN 205 767 R600 2 SN 205 768 R2700 2 SN 205 769 R2000 2 SN 205 770 R2500 22 SN 205 77 R200 22 SN 205 772 R300 2 SN 205 773 R400 2 SN 205 774 R500 2 SN 205 775 R600 2 SN 205 776 R700 2 SN 205 777 R000 2 SN 205 778 R200 22 SN 205 779 R2200 22 SN 206 394 R0200 4 SN 290 28 R000 29 SN 290 282 R0200 29 SN 29 04 R2000 25 SN 29 042 R200 25 SN 29 05 R2200 25 SN 29 052 R2300 25 SN 29 06 R2400 25 SN 29 062 R2500 25 SN 29 077 R2400 25 SN 29 02 R2300 25 SN 29 03 R2400 25 SN 29 04 R2500 25 SN 29 05 R2600 25 SN 29 06 R2700 25 SN 29 07 R2000 25 SN 29 08 R000 25 SN 29 09 R0200 25 SN 29 0 R2600 25 SN 29 22 R600 27 SN 29 23 R700 27 SN 29 28 R2400 27 SN 29 29 R2500 27 SN 29 44 R2400 27 SN 29 45 R2500 27 SN 29 50 R0600 25 SN 29 60 R0000 25 SN 29 6 R2500 27 SN 29 62 R2600 27 SN 29 70 R0200 27 SN 29 94 R700 27 SN 29 95 R000 27 SN 29 30 R0200 29 SN 29 302 R0300 29 SN 29 3 R2300 29 SN 29 32 R2400 29 SN 29 322 R2600 29 SN 29 323 R2700 29 SN 29 324 R2000 29 SN 29 325 R200 29 SN 29 352 R0400 25 SN 29 362 R0600 25 SN 29 372 R0000 25 SN 29 46 R2200 28 SN 29 462 R2300 28 SN 29 472 R2500 28 SN 29 474 R2700 28 SN 29 476 R200 28 SN 29 478 R0300 28 SN 29 480 R2200 28 SN 29 482 R000 28 SN 29 484 R200 28 SN 296 35 R0000 4 SN 399 563 R0400 28 SN 399 57 R0400 28 SN 399 572 R0500 28 SN 399 574 R0700 28 SN 399 62 R0600 28 SN 399 903 R0200 4 D D /5.DO.Ex 33 D /5.N.DO.Ex 33 D /5.P.DO.Ex 33 D 0/0.2L.Ex 28 D 0/0.N.2L.Ex 28 D 0/0.P.2L.Ex 28 D 20/42.FF.Ex 2 D,5/6.DO.Ex 33 D,5/6.D2.DO.Ex 35 D,5/6.D2.N.DO.Ex 35 D,5/6.N.DO.Ex 33 D,5/6.P.DO.Ex 33 D 6/2.2L.Ex 28 D 6/2.N.2L.Ex 28 D 6/2.P.2L.Ex 28 D 85/55.FF.Ex 22 D 2,5/5.....2L.2L.Ex 27 D 2,5/5....2L.Ex 25 D 2,5/5....3L.Ex 25 D 2,5/5....4L.Ex 25 D 2,5/5.2L.2L.Ex 27 D 2,5/5.2L.Ex 25 D 2,5/5.3L.Ex 25 D 2,5/5.4L.Ex 25 D 2,5/5.DO.Ex 30 D 2,5/5.I.3L.Ex 26 D 2,5/5.N.2L.2L.Ex 27 D 2,5/5.N.2L.Ex 25 D 2,5/5.N.3L.Ex 25 D 2,5/5.N.4L.Ex 25 D 2,5/5.N.DO.Ex 30 D 2,5/5.P.2L.Ex 25 D 2,5/5.P.3L.Ex 25 D 2,5/5.P.4L.Ex 25 D 2,5/5.P.DO.Ex 30 D 2,5/6.D...Ex 8 D 2,5/6.D.Ex 8 D 2,5/6.D.N.Ex 8 D 2,5/8.DO.Ex 34 D 2,5/8.N.DO.Ex 34 D 2,5/8.P.DO.Ex 34 D 300/55.FF.Ex 22 D 35/6.2L.Ex 28 D 35/6.N.2L.Ex 28 D 35/6.P.2L.Ex 28 D 35/27.FF.Ex 2 D 36/6.2L.Ex 28 D 4/6....2L.Ex 27 D 4/6.2L.Ex 27 D 4/6.DO.Ex 30 D 4/6.D2.DO.Ex 32 D 4/6.D2.N.DO.Ex 32 D 4/6.N.2L.Ex 27 D 4/6.N.DO.Ex 30 D 4/6.P.2L.Ex 27 D 4/6.P.DO.Ex 30 D 4/8.DO.Ex 34 D 4/8.N.DO.Ex 34 D 4/8.P.DO.Ex 34 D 6/8....2L.Ex 27 D 6/8.2L.Ex 27 D 6/8.DO.Ex 30 D 6/8.DO3.Ex 3 D 6/8.N.2L.Ex 27 D 6/8.N.DO.Ex 30 D 6/8.N.DO3.Ex 3 D 6/8.P.2L.Ex 27 D 6/8.P.DO.Ex 30 D 6/8.P.DO3.Ex 3 D 70/32.FF.Ex 2 DB 2,5/5.2L.Ex 29 DB 2,5/5.N.2L.Ex 29 DB 4/6.DO.Ex 36 DR,5/6.DO.Ex 38 DR,5/6.PI.DO.Ex 38 DR 2,5/0.P.4L.Ex 29 DR 2,5/5.2L.Ex 29 DR 2,5/5.N.2L.Ex 29 DR 4/6....Ex 24 DR 4/6..Ex 24 DR 4/6..N.Ex 24 DR 4/6.DO.Ex 36 DR 4/6.Ex 24 DR 4/6.N.Ex 24 DR 4/6.P.Ex 24 DR 4/6.PI.DO.Ex 36 DR 4/8.DO.Ex 37 DR 4/8.PI.DO.Ex 37 DR... 4/6.DO.Ex 36 DRE 4/6.DO.Ex 36 DS,5/6... DO.Ex 38 DS,5/6.DO.Ex 38 DS,5/6.N.DO.Ex 38 DS 4/6... DO.Ex 36 DS 4/6.DO.Ex 36 DS 4/6.N.DO.Ex 36 M M 0/0...Ex 5 M 0/0.Ex 5 M 0/0.N.Ex 5 M 0/0.P.Ex 5 M 0/0.PI.Ex 5 M 0/0.RS.Ex 9 M 6/2...Ex 5 M 6/2.Ex 5 M 6/2.N.Ex 5 M 6/2.P.Ex 5 M 35/6...Ex 6 M 35/6.Ex 6 M 35/6.N.Ex 6 M 35/6.P.Ex 6 M 4/6...Ex 4 M 4/6.3...Ex 4 M 4/6.3.Ex 4 M 4/6.3.N.Ex 4 M 4/6.4...Ex 4 M 4/6.4.Ex 4 M 4/6.4.N.Ex 4 M 4/6.D2.Ex 7 M 4/6.Ex 4 M 4/6.N.Ex 4 M 4/6.P.Ex 4 M 4/6.PI.Ex 4 M 4/6.RS.Ex 9 M 6/8...Ex 5 M 6/8.Ex 5 M 6/8.N.Ex 5 M 6/8.P.Ex 5 M 6/8.PI.Ex 5 M 6/8.RS.Ex 9 M 70/22...Ex 6 M 70/22.Ex 6 M 70/22.N.Ex 6 M 70/22.P.Ex 6 M 70/22.PI.Ex 6 M 95/26...Ex 6 M 95/26.Ex 6 M 95/26.N.Ex 6 M 95/26.P.Ex 6 M 2,5/5...Ex 4 M 2,5/5.D2....Ex 7 M 2,5/5.D2..Ex 7 M 2,5/5.D2.Ex 7 M 2,5/5.D2.N.Ex 7 M 2,5/5.Ex 4 M 2,5/5.N.Ex 4 M 2,5/5.P.Ex 4 M 2,5/5.PI.Ex 4 MTC 6.Ex 20 39

s part of its on-going product improvement, BB reserves the right to modify the characteristics or the products described in this document. The information given is not-contractual. For further details please contact the BB company marketing these products in your country. SNC 60 004 C0204 BB France utomation Products Division Export Department 0, rue mpère Z.I. - B.P. 4 F-69685 Chassieu cedex / France Tel. : +33 (0)4 7222 722 Fax : +33 (0)4 7222 935