C7 Control Systems PLC and Operator Panel in one device. Product Brief November 2003

C7 Control Systems PLC and Operator Panel in one device Product Brief November 2003

Overview, advantages, innovation SIMATIC C7 control systems comprising SIMATIC OP & S7-300 SIMATIC OP SIMATIC S7-300 SIMATIC C7 Overview In addition to pure control functions, it is also necessary to solve many different types of HMI functions on your machine. Furthermore, you may also have to satisfy customer demands and configure your machine together with the controller in an extremely compact design. You therefore wish to implement a complete machine controller in just one unit? The SIMATIC C7 all-in-one control systems have been optimized for exactly such applications, and combine an S7-300 PLC and an operator panel in one single unit. It has therefore become possible to implement complete yet expandable machine controllers within the smallest possible space and at a lower cost (hardware and engineering overheads). The PLC part comprises CPU, I/O and interface to the I/O expansion; the HMI part is either a line-oriented or pixel graphics OP depending on the type. Advantages Combining a PLC and an OP in one device outfits the SIMATIC C7 control systems with the following advantages Less space needed: the compact design uses up much less space in the machine. Time savings: the ready-to-use control solution lowers engineering overhead, e.g. for configuration, installation and wiring Cost savings: up to 20% lower procurement costs compared with a similar modular solution - often the control cabinet is smaller or becomes totally superfluous or the C7 device can be integrated directly in the operator panel. Flexibility: simple expansion with S7-300 modules means that C7 devices are open for comprehensive and complex automation solutions. System integration: Since C7 is a full member of Totally Integrated Automation all advantages with regard to system integration can be taken for granted. Innovation The all-in-one C7-613 and C7-635 systems and the new C7-636 system with integral compact CPU profit from the further development of these S7-300 CPUs and offer even more functionality and performance: Fast actual-value recording with direct access to hardware counters and inputs for the counting and frequency measurement functions permit a significant improvement in dynamic characteristics, e.g. for positioning tasks. Tripling of the processing speed for floating-point commands results in noticeably faster program execution with mathematical functions. Scanning of the serial number of the Micro Memory Card (MMC) during operation permits copy protection for the user software. Increasing the number of function calls and data blocks facilitates the portability of user programs which were developed for C7 devices with standard CPUs and are now also to be used on C7 devices with compact CPUs. Together with the integral analog output, the new positioning functions permit direct control of MICROMASTER frequency converters. C7-635 and C7-636 support the DPV1 standard. Parameterization and optimization of field devices during runtime results in shorter setup times. Detailed device diagnostics reduce down times. In addition, C7-613, C7-635 and C7-636 can also display Cyrillic and various Asian characters (Chinese, Japanese, Korean, inter alia). This greatly facilitates the export of such devices. 2

Application Many sectors, customized design At home in many sectors Applications for the C7 all-in-one control systems include: General mechanical engineering (construction of series machines in particular) Special machines Plastics and textiles machines Woodworking machines and many other applications The high industrial capability of the SIMATIC C7 systems means they are available for universal use and are characterized by: High EMC Withstand high levels of shock and vibration Up to 50 ºC even if no fan is used Fulfill national and international standards according to DIN, UL, CSA, FM, ISO 9001 and marine classifications Transparent distillation process thanks to clear SIMATIC C7 display Customized design The SIMATIC C7 all-in-one control systems can also be incorporated into customized designs. This is advantageous if the all-in-one systems have to be optically matched to the machine or plant. The design can be changed in various manners: Customized company logo Special color: Optional RAL or Pantone colors are available for company logo, front membrane and front frame Customized key inscriptions Recipe-based cream production with SIMATIC C7 International character sets facilitate exporting of SIMATIC C7 C7 all-in-one systems with customized design for adaptation to the respective machine or plant 3

Overview for selection of correct C7 device Integrated components C7-613 C7-621 C7-621 ASi C7-633/P C7-633 DP PLC-CPU CPU 313C CPU 314 CPU 314 CPU 315 CPU 315-2 DP CPU user memory 32 KB 48 KB 64 KB OP -- OP3 OP7 No. of lines x characters 4x20 2x20 4x20 I/Os 24 DI/16 DO 4 AI + 1 PT100 2AO 16 DI/16 DO 4AI/1AO - 16 DI/16 DO 4AI/4AO 4 alarms/counters/ frequency - Communications interface MPI MPI, AS-Interface MPI MPI, PROFIBUS DP (master or slave) Programming PLC section HMI section STEP 7 Lite, STEP7 STEP 7 Lite, STEP7 STEP 7, STEP 7 Lite, ProTool/Lite, ProTool, ProTool/Pro STEP 7 ProTool/Lite, ProTool, ProTool/Pro STEP 7, STEP 7 Lite, ProTool/Lite, ProTool, ProTool/Pro STEP 7, ProTool/Lite, ProTool, ProTool/Pro Integrated components C7-634/P C7-634 DP C7-635 Key C7-635 Touch C7-636 Key PLC CPU CPU 315 CPU 315-2 DP CPU 314C-2 DP CPU 314C-2 DP CPU 315-2 DP (new) CPU user memory 48 KB 64 KB 128 KB OP OP17 OP 170 TP 170B OP 270 No. of lines x characters Resolution 4 x 20 or 8 x 40 Pixel graphics, vector graphics 320 x 240 (5,7 ) Color display 320 x 240 (5,7 ) I/Os 16DI/16 DO 4 AI/4 AO 4 alarms/counters /frequency 24 DI/16 DO 4 AI + 1 PT100 2AO 4 counters/frequency 4 pulses Communications interface MPI MPI, PROFIBUS DP (master or slave) Programming PLC section HMI section STEP 7, STEP 7 Lite ProTool/Lite, Pro- Tool, ProTool/Pro STEP 7 ProTool/Lite, ProTool, ProTool/Pro WinCC flexible STEP 7 WinCC flexible 4

Design features, S7-300 CPU, operator panel Design features All SIMATIC C7 devices are characterized by a number of important features. Housing/assembly Rugged, compact plastic and metal housing features IP65 degree of protection (at front) Installation possible in control panel, control cabinet or on beams Independent wiring with terminal blocks, i.e. problem-free replacement of devices when servicing Front panel Rugged membrane keyboard Easily readable, backlit LCD, graphics, blue mode LEDs for PLC status and operation Interfaces Powerful communication capability through the MPI multipoint interface Printer interface 1) e.g. for documenting production data and quality assurance PROFIBUS DP 1) master/slave, 12 Mbit/s AS-Interface (C7-621 ASi) Interface for user-friendly expansion with modules from the S7-300 spectrum (externally or directly on the rear panel 1) of the C7) Integrated I/O units Digital inputs 1) Digital outputs 1) Analog inputs 1) Analog outputs 1) Integrated technological functions Counters 1) Pulse outputs 1) Frequency measurement 1) Controlled positioning 1) Loop control 1) Controlling with the integral PLC An S7-300 CPU is used as the integral PLC, and provides the following functions: Fast command processing: Command processing times down to 0.1 µs permit very short machine cycle times. Maintenance-free: Retentive data saving on the Micro Memory Card (MMC) means no maintenance required for backup battery. Human-machine interfaces: Easy-to-use HMI services are already integrated in the operating system of the C7. Diagnostic functions: The intelligent diagnostics system facilitates troubleshooting and reduces plant downtimes. Password protection: A password allows you to protect your PLC know-how against unauthorized copying and writing. Floating-point arithmetic: Floating-point arithmetic means that even complex arithmetic functions can be implemented effectively. HMI with integrated operator panel The operator panel of the C7 devices permits versatile HMI functions: Operating messages and fault messages provide operators with important information on the current process sequences, e.g. for troubleshooting or also as maintenance information. Display of process images: Pixel graphic displays enable representation of the monitored machine close to reality. To permit rapid recognition of process data, they can be displayed e.g. as bars, curves or status graphs. User menu: In order to allow you to adapt the operating sequence to the application, you can define user-specific menus. Limit monitoring and password protection: Programmable limits and passwords improve security when making entries, providing safe process control. Variable printout: Printers which can be connected directly log data quickly and simply, e.g. for quality checks (not C7-613 and C7-621). Online language selection: All texts can be saved in several languages. This facilitates commissioning and servicing with international use (Cyrillic and Asian characters are also possible with C7-613, C7-635 and C7-636). Display of statuses of integral inputs/outputs. Recipe (batch) management: Up to 99 different recipes 1) can be managed simultaneously (not C7-621). Key or Touch: C7-635 Touch enables intuitive operator control and monitoring as a result of the touch-sensitive screen, and significantly reduces the acquaintance requirements of personnel. Simple, self-explanatory graphic buttons facilitate operation and avoid input errors. C7-635 Key and C7-636 Key are designed with a membrane keyboard for applications in contaminated environments. Data saving: Slot for memory card for saving of configurations and recipe data sets (Micro Memory Card for C7-613, Compact Flash Card for C7-635 and C7-636). 1) depending on the C7 version 5

Expansion options Different versions with graded performance power and the comprehensive SIMATIC S7-300 module range the SIMATIC C7 to the task in hand. If tasks become more sophisticated, the control systems can be retrofitted at any time using additional modules (FM, CP, I/O). Direct expansion The all-in-one control systems C7-613, C7-635 and C7-636 can be expanded by up to four S7-300 modules directly on the rear panel of the C7 system. Two I/O expansion sets are available for this, so that deep expansion is possible with up to four modules and slim expansion with up to two modules. An interface module (IM) is not required. The compact format is thus retained. External expansion is alternatively possible with up to four S7-300 modules using a 1.5 m long I/O cable. An interface module (IM) is not required here either. In addition, the 1.5 m long I/O cable permits greater mechanical freedom in the format. Attaching I/O modules Expansion with I/O cable (1.5m) with C7-613, C7-635, C7-636 Slim I/O Deep I/O Direct Expansion with C7-613/635/636. 6

Expansion with interface modules Special interface modules permit additional expansions with I/Os: Interface module IM 621 The C7 systems C7-621/C7-621 ASi can be expanded with up to four SIMATIC S7-300 modules using the IM 621 interface module. Interface module IM 360/361 To permit implementation of individual solutions, the all-in-one control systems C7-633, C7-634, C7-635 and C7-636 can also be expanded by up to 24 SIMATIC S7-300 modules via the IM 360/IM 361. Up to 8 modules can be inserted per rack. The PROFIBUS with its comprehensive range of I/Os can of course also be used for distributed expansion also in the S7-300 design in the case of the ET200M (see page 8). Max. 0.5 m IM 621 C7-621, C7-621 ASi (with external IM 621) Cable Max. 10 m IM 361 24 V DC IM 361 C7-633, C7-634 (IM 360 integrated) C7-635, C7-636 (ext. IM 360) S7-300-modules Cable Max. 10 m S7-300 modules 24 V DC Cable Max. 10 m IM 361 S7-300 modules 24 V DC 7

Communication using MPI, DP and ASi Integrated communications MPI The multipoint interface is a communications interface integrated in SIMATIC C7. Use this interface to establish elementary networks. The MPI allows several programming units, operator panels, S7-300 and S7-400 to be connected simultaneously: up to 32 MPI participants up to 4 communications channels per CPU transmission rate is 187.5 kbit/s The "Global Data Communications" service allows CPUs incorporated in the network to exchange data cyclically without the need for additional software programs PROFIBUS DP The all-in-one control systems C7-633 DP, C7-634 DP, C7-635 and C7-636 are available with an integral PROFIBUS DP interface. These all-inone systems can be configured in the software as masters or slaves. When using the C7 as a DP master, the distributed I/O is configured and programmed with STEP 7 as if it were a central I/O. Users need not be concerned with the communications connection. These C7 systems can also be used as slaves on the PROFIBUS DP in line with the current trend towards distributed intelligence on site. ASi (with C7621 ASi) The actuator/sensor interface (AS-Interface) is a networking system for binary sensors and actuators in the field. The sensors and actuators are connected to a common two-wire cable. The SIMATIC C7-621 ASi can be connected as master to the AS-Interface. C7-633 DP C7-634 DP S7-300 ET 200M ET 200B/L Third party device SIMOVERT drive ET 200X ET 200S Example configuration of a C7 control system with PROFIBUS DP networking Branch (without AS-Interface chip) Inductive BERO with integral AS-Interface C7-621 ASi C7-635 C7-636 AS-Interface cable Repeater + FK-E interface module AS-Interface power supply unit 4E module + FK interface submodule (with AS-Interface chip) for connecting standard sensors Max. 100 m Standard sensor, e.g. inductive BERO Standard sensor, e.g. position switch Control system C7-621 ASi with AS-Interface networking 8

Software development with STEP7 and ProTool/WinCC flexible SIMATIC industrial software With SIMATIC C7, you work with the STEP 7 and ProTool software tools from the range of SIMATIC industrial software. SIMATIC industrial software is managed centrally and possesses a wide range of matched tools. This means that the software is absolutely uniform throughout the complete project: for configuration of the hardware and communication, for programming, testing and commissioning, up to documentation. All data are only entered once using a standardized HMI. Contextbased help functions mean you don t need to search in the manual. Configuration, programming, commissioning and documentation with STEP 7 STEP 7 has the appropriate function for each task to be solved using the PLC; you can swap between the STL, LAD and FBD programming languages as desired. The STEP 7 instruction set means that even complex functions are simple to program. There are two versions for selection. Beginners in the STEP 7 environment should preferably use the low-cost software version STEP 7 Lite. The STEP 7 basic package is correct for all others also because it permits use of application-oriented engineering tools. The tool for HMI: ProTool ProTool/Lite, ProTool, ProTool/Pro or WinCC flexible are used to configure the HMI functionalities of the SIMATIC C7 system, and are optimally incorporated in STEP 7. Common data management is used, permitting e.g. direct access to symbol lists or communications parameters. SIMATIC ProTool has been produced according to state-of-the-art knowledge on the design of configuration desktops. For example, pictures and messages are configured on the PC without the need to use a C7 (offline configuration). With the low-cost all-in-one control system C7-613, the HMI configuration is carried out using STEP 7 ProTool is not required for this. Simple editing of display texts is possible using new parameterization support (can be installed with STEP 7 V5.2 and later). These parameterization forms are used to directly generate the data blocks with the parameters and variables for the STEP 7 project of the C7-613. The new C7-636 system is configured using WinCC flexible, the innovated HMI software for all applications from panels up to PCs. C7-621 all-in-one system with ASi-Interface networking HMIs developed offline using ProTool in use on the display of a SIMATIC C7 9

Technical Specifications C7-613, C7-621, C7-635, C7-636 General C7-613 1) C7-635 Key 2) C7-635 Touch 2) C7-636 Key 3) C7-621 C7-621 ASi Degree of protection (IEC 60529) Front: IP65, housing: IP20 Degree of protection (NEMA) NEMA 4X Permissible ambient temp. vertical operation mounted at 45º 0 to 50 ºC 0 to 45 ºC, restricted readability with horizontal installation Relative humidity 5 to 95% at 25 C (no condensation), tested in accordance with DIN IEC 60068-2-3 Acceptance, certification EN 61131-2 (IEC 1131-2); UL Listing UL 508; Canadian Standard Association (CSA) in accordance with Standard C22.2 number 142; FM approval, FM-standards No. 3611, 3600, 3810 Class I, Div. 2 Group A, B, C, D; DIN/ISO 9001 Certification of manufacture and design Supply voltage rated value permissible range 24 V DC 20.4 to 28.8 V 24 V DC 20.4 to 30.2 V Current consumption, max. 2.4 A 1 A Power loss, max 58 W 24 W Dimensions Device (B x H x T) in mm Panel cutout (B x H) mm 215 x 165 x 79 202 x 152 260 x 274 x 79 231 x 257 240 x 199 x 79 231 x 183 260 x 274 x 80 231 x 257 168 x 120 x 69 158.5 x 110.5 Weight 920 g 1500 g 1400 g 1500 g 800 g PLC User memory (1 instruction corresponds to an average of 3 byte) 32 KB/10 K instructions RAM 64 KB /20 K instructions RAM 128 KB/ 40 K instructions RAM 32 KB/10 K instructions RAM Loading memory integrated (for data) removable, max. Data buffering with battery without battery, max. No. of blocks, max. Program execution 8 MB (MMC) Program and data through MMC 512 FC 512 FB 511 DB 8 MB (MMC) 2048 FC, 2048 FB, 1023 DB Free cycle (OB 1), clock-controlled (OB 10), time-delay interrupt (OB 20), time interrupt (OB 35), process alarm (OB 40), restart (OB 100, 102), asynchronous fault (OB 80..82, 85, 87), synchronous fault (OB 121, 122), DPV1 alarms (OB 55-57, not with C7-613) 48 KB RAM, 48 KB FEPROM 144 byte, configurable for flags, counters, data 32 FC 32 FB 63 DB Restart (OB 100) Free cycle (OB 1) Interrupt-driven (OB 40) Error handling (OB 80, 81, 82, 85, 86, 87, 121, 122) Execution times for: Bit operations Word operations Fixed point addition Floating point addition 0.1 µs 1 µs 2 µs 3 µs 0.3 to 0.6 µs 1 µs 2 µs 50 µs Bit memories 256 byte 2048 byte 256 byte 10 1 ) C7-613 innovated: start of delivery January 2004 2 ) C7-635 innovated: 3 ) C7-636 new: start of delivery December 2003 start of delivery January 2004

C7-613 C7-635 Key C7-635 Touch C7-636 Key C7-621 C7-621 ASi Integrated functions Counters Pulse output 3 increm. enc. 24 V/30 khz 3 channels PCM max. 2.5 khz 4 incremental encoders 24 V/60 khz 4 channels pulse-width modulation (PCM) max. 2.5 khz Frequency measurement 3 channels max. 30 khz 4 channels max. 60 khz Controlled positioning Loop control PID controller SFB for positioning 1 axis via 2 DO, AO PID controller Counters/counter range 256/0 to 999 64/0 to 999 Timers/time range 256/10 ms to 9990 s 128/1 to 9990 s S7-300 expansion modules max. 4 max. 24 max. 4 Usable modules FM CP, point to point CP, LAN 4 2 1 8 8 10 4 2 1 Total I/O addressing space 1024/1024 byte 128/128 byte Process image 128/128 byte 64/64 byte Multi-point interface MPI yes, occ. 1 station per device yes, occupies 2 stations per device (1x CPU, 1x OP) yes, occ. 2 stations per device (1x CPU, 1x OP) PROFIBUS DP interface 1 DP connection (master/slave) 1 (CP 342-5) 1 (integrated, master/slave), 1 (CP 342-5) 1 (CP 342-5) AS-Interface-Master interface integrated 1 Digital input (DI) 24; 24 V DC; all channels can be used for process interrupts 16 Digital output (DO) 16; 24 V DC; 0.5 A 16 Universal inputs (UI) See integral functions Analog inputs (AI) 4: ± 10 V, 0 10 V, ± 20 ma, 0/4-20 ma; 1: 0 600 W, Pt100 4 Analog outputs (AO) 2: ± 10 V, 0 10 V, ± 20 ma, 0/4-20 ma 1 Programming, configuration Programming software Configuring control and monitoring STEP 7, V5.3 STEP 7 STEP 7, V5.2, SP1 ProTool/Lite, ProTool, ProTool/Pro, WinCC flexible STEP 7, V5.2, SP1 WinCC flexible ProTool STEP 7, STEP 7-Lite ProTool/Lite, ProTool, ProTool/Pro OP Display Lines x characters per line Character height Resolution Act. display area (W x H) mm LC display, LED backlit 4 x 20 5 mm LC display CCFL backlit 320 x 240 pixels 116 x 87 (5.7 ) Touch resistive, CCFL backlit 320 x 240 pixels 116 x 87 (5.7 ) STN display, CCFL backlit, Color 320 x 240 pixels 116 x 87 (5.7 ) LC display LED backlit 2 x 20 5 mm 11

Technical Specifications C7-613, C7-621, C7-635, C7-636 C7-613 C7-635 Key C7-635 Touch C7-636 Key C7-621 C7-621 ASi Number of softkeys/function keys 4/10 14/10 14/10 5/ Process signals, max. 128 1) 400 1) 2000 499 Fault signals, max. 128 1) 400 1) 2000 Number of pictures 128 100 300 40 Pixel graphics, vector graphics Semi graphics In scope of character set Recipes, max. 20 300 Online languages 3 2) 3 2) 5 2) 3 Clock Real-time clock (hardware) Software clock Printer interface RS232 RS232, USB MLFB group 6ES7613-1CA... 6ES7635-2EC... 6ES7635-2EB... 6ES7636-2EC... 6ES7621-1AD... 6ES7621-6BD... 1) Total number for process signals and fault signals 2) Also Cyrillic, Chinese, Taiwanese and many others 12

Technical Specifications C7-633, C7-634 General C7-633/P C7-633 DP C7-634/P C7-634 DP Degree of protection (IEC 60529) Permissible ambient temperature vertical operation mounted at 45º Front: IP65, housing: IP20 0 to 50 ºC, 0 to 45 ºC, restricted readability with horizontal installation Relative humidity 5 to 95% at 25 C (no condensation), tested in accordance with DIN IEC 60068-2-3 Acceptance, certification EN 61131-2 (IEC 1131-2); UL Listing UL 508; Canadian Standard Association (CSA) in accordance with C22.2 Number 142; FM approval, FM standards No. 3611, 3600, 3810 Class I, Div. 2 Group A, B, C, D; DIN/ISO 9001 Certification of manufacture and design Supply voltage rated value permissible range 24 V DC 20.4 to 30.2 V 24 V DC 20.4 to 30.2 V Current consumption, max. 1 A 1 A Power loss, max 24 W 24 W Dimensions Device (B x H x T) in mm Panel cutout (B x H) mm 240x203.5x89.4 231 x 159 240x203.5x74.4 231 x 159 240x203.5x89.4 231 x 159 240x203.5x74.4 231 x 159 Weight 1800 g 1600 g 1900 g 1700 g PLC User memory (1 instruction corresponds to an average of 3 byte) 48 KB/ 16 K instructions RAM 64 KB/ 20 K instructions RAM 48 KB/ 16 K instructions RAM 64 KB/ 20 K instructions RAM Loading memory integrated (for data) removable, max. 80 KB RAM 512 KB 96 KB RAM 512 KB 80 KB RAM 512 KB 96 KB RAM 512 KB Data buffering with battery without battery, max. No. of blocks, max. Program and data 4736 byte, configurable for flags, counters, data 128 FC, 128 FB or 127 DB Program execution Restart (OB 100) Free cycle (OB 1) Clock-controlled (OB 10) Time-controlled (OB 35) Interrupt-driven (OB 40) Error handling (OB 80, 81, 82, 85, 86, 87, 121, 122) Execution times for: Bit operations Word operations Fixed point addition Floating point addition 0.3 to 0.6 µs 1 µs 2 µs 50 µs 0.3 to 0.6 µs 1 µs 2 µs 50 µs Bit memories 256 byte 256 byte 13

Technical Specifications C7-633, C7-634 C7-633/P C7-633 DP C7-634/P C7-634 DP Counter/counter range 64/0 to 999 64/0 to 999 Timers/timer range 128/10 to 9990 s 128/10 ms to 9990 s S7-300 expansion modules max. 24 max. 24 Usable modules FM CP, point to point CP, LAN 8 4 2 Total I/O addressing space 256/256 byte 256/256 byte Process image 128/128 byte 128/128 byte 8 4 2 Multi-point interface MPI yes, occupies 2 stations per device (1x CPU, 1x OP) PROFIBUS DP interface 1 1 DP connection (master/slave) 1 (CP 342-5) 1 (integr., Master/ Slave) 1 (CP 342-5) AS-Interface-Master interface integrated 1 (CP 342-5) 1 (integr., Master/ Slave) 1 (CP 342-5)) Digital input (DI) 16 16 Digital output (DO) 16 16 Universal inputs (UI) 4 1) 4 1) Analog inputs (AI) 4 4 Analog outputs (AO) 4 4 Compact input/output module (16 DI, 16 DO, 4 AI, 4AO, 4 UI) 1 1 1 1 Programming, configuration Programming software Configuring control and monitoring STEP 7, STEP 7-Lite ProTool/Lite, ProTool STEP 7 ProTool/Pro STEP 7, STEP 7-Lite ProTool/Lite, ProTool, ProTool/Pro STEP 7 ProTool/Lite, ProTool, ProTool/Pro 1 ) Can be used as 24 V DC digital inputs or alarm inputs, or for upward/downward counting up to 10 khz, or for frequency/period measurements 14

C7-633/P C7-633 DP C7-634/P C7-634 DP OP Display Lines x characters per line Character height Resolution Active display area (W x H) in mm LC display, LED backlit 4 x 20 8 mm LC display, LED backlit 4 x 20 / 8 x 40 11 / 6 mm Number of softkeys/function keys 4/16 8/16 Process signals, max. 499 999 Fault signals, max. 499 999 Number of pictures 99 99 Pixel -, vector graphics Semi-graphics In scope of character set Recipes, max. 99 99 Online languages 3 3 Clock Software clock Real-time clock (hardware) Printer interface RS232 RS232 MLFB group 6ES7633-1DF... 6ES7633-2BF... 6ES7634-1DF... 6ES7634-2BF... 15

Dimension drawings All dimensions in mm, not to scale C7-613 C7-621 152 +1 110 +0,5 202+1 79 215 Panel cutout 158+0,5 69 Panel cutout 165 120 168 the products. An obligation to provide the respective characteristics shall only exist if expressly agreed in the terms of contract. Availability and technical specifications are subject to change without notice. C7-633 C7-634 230,5+0,5 Panel cutout 74,4 240 158,5 +0,5 203,5 C7-635 Key 231+1 Panel cutout 80 260 257 +1 274 C7-635 Touch Panel cutout 231+1 80 260 183 +1 199 C7-636 Key 257 +1 Further information regarding SIMATIC C7 can be found in the Internet: www.siemens.com/simatic-c7 231+1 Panel cutout 80 To get in touch with your contact person for SIMATIC near you, look in the Internet under: www.siemens.com/automation/partner 274 260 With the A&D Mall you can order electronically using the Internet: www.siemens.com/automation/mall The information provided in this brochure contains descriptions or characteristics of performance which in case of actual use do not always apply as described or which may change as a result of further development of Siemens AG Automation and Drives Postfach 4848, D-90327 Nürnberg Federal Republic of Germany www.siemens.com/simatic-c7 Siemens AG 2003 Subject to change without prior notice Order No. 6ZB5310-0FM02-0BA9 Printed in the Federal Republic of Germany 26100/401287 KB 1203 3. MAN En All designations marked in this Product Brief with are registered trademarks of Siemens AG.