Six Sigma Acronyms $k Thousands of dollars $M Millions of dollars % R & R Gauge % Repeatability and Reproducibility ANOVA Analysis of Variance AOP Annual Operating Plan BB Black Belt C & E Cause and Effects matrix CEO Chief Executive Officer CFO Chief Financial Officer CIO Chief Information Officer COB Chairman of the Board of Directors COO Chief Operating Officer COPQ Cost of Poor Quality 2-1 Do Not Reprint without permission of
Six Sigma Acronyms Cp Cpk DMAIC DOE DPU F(x) FMEA FPY GB IS ISO KPIV KPOV LSL Index of process capability Index of process capability process not centered Define, Measure, Analyze, Improve, Control Design of Experiments Defects Per Unit Function relating process inputs to process outputs Potential Failure Modes and Effect Analysis First Pass Yield Green Belt Information Systems International Standards Organization Key Process Input Variable Key Process Output Variable Lower Specification Limit 2-2 Do Not Reprint without permission of
Six Sigma Acronyms MAIC MBB MSA Multi-Vari P/T PPM QA QC R & R R RTY s Measure, Analyze, Improve, Control Master Black Belt Measurement System Analysis Type of multiple variable process study Measurement precision to customer tolerance ratio Parts Per Million Quality Assurance Quality Control Recognition and Reward Range Rolled Throughput Yield Standard Deviation 2-3 Do Not Reprint without permission of
Six Sigma Acronyms SOP SPC TQM USL X X-BAR Y YB Y-BAR Standard Operating Procedure Statistical Process Control Total Quality Management Upper Specification Limit Process Input variable including process variables Average of the variable X Process Output variable Yellow Belt Average of the variable Y 2-4 Do Not Reprint without permission of
Alpha Risk: The probability of accepting the alternate hypothesis when; in reality, the null hypothesis is true. Alternate Hypothesis: A tentative explanation that indicates that an event does not follow a chance distribution; a contrast to the null hypothesis. Assignable Cause: A source of variation which is non-random; a change in the source ( VITAL FEW variables) produces a significant change of some magnitude in the response (dependent variable) e.g., a correlation exists; the change may be due to an intermittent in-phase effect or a constant cause system which may or may not be highly predictable. An assignable cause is often signaled by an excessive number of data points outside a control limit and/or a non-random pattern within the control limits; an unnatural source of variation; most often economical to eliminate. 2-5 Do Not Reprint without permission of
Assignable Variations: Variations in data that can be attributed to specific causes. Attribute: A characteristic that may take on only one value (e.g., 0 or 1). Attribute Data: Numerical information at the nominal level; subdivision is not conceptually meaningful; data that represents the frequency of occurrence within some discrete category (e.g., 42 solder shorts). Background Variables: Variables that are of no experimental interest and are not held constant; their effects are often assumed insignificant or they are randomized to ensure that contamination of the primary response does not occur. Beta Risk: The probability of accepting the null hypothesis when, in reality, the alternate hypothesis is true. Black Belt: The leader of the team responsible for applying the Six Sigma process. 2-6 Do Not Reprint without permission of
Blocking Variables: A relatively homogenous set of conditions within which different conditions of the primary variables are compared; used to ensure that background variables do not contaminate the evaluation of primary variables. Boxplot (, box-and-whisker plots): A graph which is particularly useful for showing the distribution characteristics of data. A line is drawn across the box at the median. By default, the bottom of the box is at the first quartile (Q1), and the top is at the third quartile (Q3) value. The whiskers are the lines that extend from the top and bottom of the box to the adjacent values. The adjacent values are the lowest and highest observations that are still inside the region defined by the following limits: Lower Limit: Q1: 1.5 (Q3 Q1); Upper Limit: Q3 + 1.5 (Q3 Q1); Outliers are points outside of the lower and upper limits and are plotted with asterisks (*). Causality: The principle that every change implies the operation of a cause. 2-7 Do Not Reprint without permission of
Causative: Effective as a cause. Cause: That which produces an effect or brings about a change. C Charts: Charts that display the number of defects per sample. Champion: A member of senior management who is responsible for the logistical and business aspects of the program. Characteristic: A definable or measurable feature of a process, product, or variable. Central Tendency: Numerical average (e.g., mean, median, and mode); center line on a statistical process control chart. Center Line: The line on a statistical process control chart that represents the characteristic s central tendency. Classification: Differentiation of variables. Common Cause: type of process variation that exist normally in the current process state, also called inherent variation. The reasons data values go up are the same reason data values go down. 2-8 Do Not Reprint without permission of
Confidence Level: The probability that a random variable X lies within a defined interval. Confidence Limits: The two values that define the confidence interval. Confounding: Allowing two or more variables to vary together so that it is impossible to separate their unique effects. The but word. Continuous Data: Numerical information at the interval of ratio level; subdivision is conceptually meaningful; can assume any number within an interval (e.g., 14.652 amps). Continuous Random Variable: A random variable that can assume any value continuously in some specified interval. Control Chart: A graphical rendition of a characteristic s performance across time in relation to its natural limits and central tendency. Control Specifications: Specifications called for by the product being manufactured. 2-9 Do Not Reprint without permission of
Cost Of Poor Quality (COPQ): Money spent or lost on non-valueadded activities while producing a good or service. The cost of finding and fixing defects, failing to meet customer expectations the first time, missed opportunity for increased efficiency, potential for higher profits, loss in market share, increase in cycle time, labor associated with ordering replacement material, and costs associated with disposing of defects. Cutoff Point: The point that partitions the acceptance region from the reject region. Data: Factual information used as a basis for reasoning, discussion, or calculation; often refers to quantitative information. Defect: An opportunity which the unit does not meet the customer s specification or requirement. A unit can have multiple opportunities for defects. Defective: A unit with one or more defects. 2-10 Do Not Reprint without permission of
Defects Per Million Opportunities (DPMO): [# Defects/(# of Units * # Opportunities)] * 1M; allows comparison of unlike products, services and processes by considering the total number of opportunities that exist for a defect to occur. Defects Per Unit (DPU): # of Defects / # Units; the ratio of the total number of defects in a product or service to the total number of units produced. A unit can have more than one defect. DPU can range from zero to the total number of defect opportunities. Degrees Of Freedom: The number of independent measurements available for estimating a population parameter. Often n-1. Density Function: The function yielding the probability that a particular random variable takes on any one of its possible values. Dependent Variable: A Response Variable; e.g., Y is the dependent or response variable where Y = f(xl... XN). Discrete Random Variable: A random variable that can assume values only from a definite number of discrete values. 2-11 Do Not Reprint without permission of
Distributions: Tendency of large numbers of observations to group themselves around some central value with a certain amount of variation or scatter on either side. Drill Down: Slang term used in Pareto and fishbone analysis; means getting to the root cause rather than staying at a symptom level of a problem. Effect: That which was produced by a cause. Experiment: A test under defined conditions to determine an unknown effect; to illustrate or verify a known law; to test or establish a hypothesis. Experimental Error: Variation in observations made under identical test conditions; also called residual error; the amount of variation that cannot be attributed to the variables included in the experiment. Unexplained variation Factors: Independent variables that are controllable for experimentation purposes 2-12 Do Not Reprint without permission of
Failure Modes and Effects Analysis (FMEA): A tool used to identify high-risk areas within a process by rating the severity, the frequency and the ease of detection for each potential failure mode of a process. First Time Yield (FTY): # of good units or total units. How many good products or services were produced at the end of the process. If items are reworked or repaired during the process but pass final inspection, they are counted as good in the first-time yield calculation. Fishbone: Also known as a cause-and-effect and/or Ishikawa diagram; a diagram to organize brainstorming information about potential causes of a problem. Diagramming helps you to see relationships among potential causes. These diagrams should start with a problem. Ask why? why? why? why? until the root causes are identified. 2-13 Do Not Reprint without permission of
Fixed Effects Model: Experimental treatments that are specifically selected by the researcher. Conclusions only apply to the factor levels considered in the analysis. Inferences are restricted to the experimental levels. Frequency Distribution: The pattern or shape formed by the group of measurements in a distribution. Gage Reliability and Reproducibility (Gage R&R): Studies that determine how much of your observed process variation is due to measurement system variation. Variation can be caused by repeatability problems; shows different results for same measurement task or reproducibility problems; different operators get different results for same measurement task. Green Belt: An individual who supports the implementation and application of Six Sigma tools by way of participation on major project teams or leading smaller projects. 2-14 Do Not Reprint without permission of
Histogram: Vertical display of a population distribution in terms of frequencies; a formal method of plotting a frequency distribution. Homogeneity of Variance: The variances of the groups being contrasted are equal (as defined by statistical test of significant difference). In Minitab called test of equal variance. Independent Variable: A controlled variable; a variable whose value is independent of the value of another variable. Interaction: When the effects of a factor (A) are not the same at all levels of another factor (B). A combined effect or more than experimental factor. Instability: Unnaturally large fluctuations in a pattern. Interval: Numeric categories with equal units of measure but no absolute zero point (i.e., quality scale or index). 2-15 Do Not Reprint without permission of
Key Process Input Variable (KPIV): The process and input variables that have the greatest impact on being able to meet the customer requirements. Key Process Output Variable (KPOV): Also known as Critical to Quality (CTQ); the customer requirements defined in measurable terms. Line Charts: Charts used to track the performance without relationship to process capability or control limits. Lower Control Limit: A horizontal dotted line plotted on a control chart that represents the lower process limit capabilities of a process. Master Black Belt: A teacher and mentor of Black Belts provides support, reviews projects, and undertakes larger scale projects. 2-16 Do Not Reprint without permission of
Nominal: Unordered categories that indicate membership or nonmembership with no implication of quantity (i.e., assembly area number one, part numbers, and so forth). Nonconforming Unit: A unit that does not conform to one or more specifications, standards, and/or requirements. Nonconformity: A condition within a unit which does not conform to some specific specification, standard, and/or requirement; often referred to as a defect; any given nonconforming unit can have the potential for more than one nonconformity. Normal Distribution: A continuous, symmetrical density function characterized by a bell-shaped curve (e.g., distribution of sampling averages). Null Hypothesis: A tentative explanation that indicates that a chance distribution is operating; a contrast to the null hypothesis. 2-17 Do Not Reprint without permission of
Opportunity: Anything that could be a fail to meet for a customer requirement. Ordinal: Ordered categories (ranking) with no information about distance between each category (i.e., rank ordering of several measurements of an output parameter). Parameter: A constant defining a particular property of the density function of a variable. Pareto Chart: Organizes data to show the major factor(s) that make up the subject being analyzed; it is a type of bar chart in which the horizontal axis represents categories of interest the major factor(s), rather than a continuous scale. The categories are often defects. By ordering the bars from largest to smallest, a Pareto chart can help you determine which of the defects comprise the vital few and which are the trivial many. A cumulative percentage line helps you judge the added contribution of each category. Pareto charts can help to focus improvement efforts on areas where the largest gains can be made. It is a search for significance. 2-18 Do Not Reprint without permission of
P Chart: Used to plot proportion defective in a sample.. Poka-Yoke: Slang term used when talking about mistake proofing processes; describes the error messages that pop up when keying information using an electronic format. Population: A group of similar items from which a sample is drawn. Often referred to as the universe. Power Of An Experiment: The probability of rejecting the null hypothesis when it is false and accepting the alternate hypothesis when it is true. Prevention: The practice of eliminating unwanted variation a priori (before the fact) e.g., predicting a future condition from a control chart and then applying corrective action before the predicted event transpires. 2-19 Do Not Reprint without permission of
Primary Control Variables: The major independent variables used in the experiment. Probability: The chance of something happening; the percent or number of occurrences over a large number of trials. Probability of An Event: The number of successful events divided by the total number of trials. Problem: A deviation from a specified standard. Problem Solving: The process of solving problems; the isolation and control of those conditions that generate or facilitate the creation of undesirable symptoms. Process: A particular method of doing something; generally involves a number of steps or operations. 2-20 Do Not Reprint without permission of
Process Average: The central tendency of a given process characteristic across a given amount of time or at a specific point in time. Process Control: See STATISTICAL PROCESS CONTROL. Process Control Chart: Any of a number of various types of graphs upon which data is plotted against specific control limits. Process Map: Graphical representation of the flow of the process; show how inputs are taken through process steps to add value in producing a final product or service. Process Spread: The range of values which a given process characteristic displays; this particular term most often applies to the range; may also encompass the variance. The spread may be based on a set of data collected at a specific point in time or may reflect the variability across a given amount of time. Project: A problem usually calling for planned action. 2-21 Do Not Reprint without permission of
R Chart: Range control chart; plot of the difference between the highest and lowest in a sample. Random: Selecting a sample so each item in the population has an equal chance of being selected; lack of predictability; without pattern. Random Cause: A source of variation which is random; a change in the source ( trivial many variables) which will not produce a highly predictable change in the response (dependent variable) e.g., a correlation does not exist; any individual source of variation results in a small amount of variation in the response; cannot be economically eliminated from a process; an inherent natural source of variation. Randomness: A condition in which any individual event in a set of events has the same mathematical probability of occurrence as all other events within the specified set (i.e., individual events are not predictable even though they may collectively belong to a definable distribution). 2-22 Do Not Reprint without permission of
Random Sample: One or more samples randomly selected from the universe (population). Random Variable: A variable that can assume any value from a set of possible values. Range: The difference between the highest and lowest values in a set of values or subgroup. Ranks: Values assigned to items in a sample to determine their relative occurrence in a population. Ratio: Numeric scale that has an absolute zero point and equal units of measure throughout (i.e., measurements of an output parameter amps). Reliability: The ability for one gage to consistently get the same results for the same task. 2-23 Do Not Reprint without permission of
Replication: Observations made under identical test conditions. Representative Sample: A sample that accurately reflects a specific condition or set of conditions within the universe. Reproducibility: The ability for all operators and gages to consistently produce the same results as one another for the same task.. Residual Error: unexplained variation in a statistical model Response Surface Model (RSM): A form of a design of experiment (DOE) that visually shows the impact of two key process variables on the key process output variable. Robust: The condition or state in which a response parameter exhibits hermetically to external cause of a nonrandom nature (i.e., impervious to perturbing influence). 2-24 Do Not Reprint without permission of
Rolled Through Put Yield (RTY): e -dpu. A ratio of the number of products or services made with no re-work or repairs before the end of the process compared to the total number produced. It can be estimated using the above formula. Sample: One or more observations drawn from a larger collection of observations or universe (population). Scatter Diagrams: Charts which allow the study of correlation, e.g., the relationship between two variables. 2-25 Do Not Reprint without permission of
Six Sigma (6s): Sigma s is a letter in the Greek alphabet. The term sigma is used to designate the distribution or spread about the mean (average) of any process or procedure. For a business or manufacturing process, the sigma value is a metric that indicates how well that process is performing. The higher the sigma value, the better. Sigma measures the capability of the process to perform defect-free-work. A defect is anything that results in customer dissatisfaction. Sigma is a statistical unit of measure which reflects process capability. The sigma scale of measure is perfectly correlated to such characteristics as defects-per-unit, parts-per million defective, and the probability of a failure/error. Meaning no more than 3.4 parts per Million. Special Cause: See ASSIGNABLE CAUSE. Stable Process: A process that is free of assignable causes, e.g., in statistical control. 2-26 Do Not Reprint without permission of
Standard Deviation: A statistical index of variability which describes the spread. Statistical Control: A quantitative condition that describes a process that is free of assignable/special causes of variation, e.g., variation in the central tendency and variance. Such a condition is most often evidenced on a control chart, i.e., a control chart that displays an absence of nonrandom variation. Statistical Process Control: The application of statistical methods and procedures relative to a process and a given set of standards. Strawman: Term used to describe rough initial outline of a presentation, concept or idea. Subgroup: A logical grouping of objects or events which displays only random event-to-event variations, e.g., the objects or events are grouped to create homogenous groups free of assignable or special causes. By virtue of the minimum within group variability, any change in the central tendency or variance of the universe will be reflected in the subgroup-to-subgroup variability. 2-27 Do Not Reprint without permission of
Symptom: That which serves as evidence of something not seen. System: That which is connected according to a scheme. Systematic Variables: A pattern that displays predictable tendencies. Theory: A plausible or scientifically acceptable general principle offered to explain phenomena. Test of Significance: A procedure to determine whether a quantity subjected to random variation differs from a postulated value by an amount greater than that due to random variation alone. Unit: An individual product or service defined in terms of what is a unit to a customer. Unnatural Pattern: Any pattern in which a significant number of the measurements do not group themselves around a center line; when the pattern is unnatural, it means that outside disturbances are present and are affecting the process. 2-28 Do Not Reprint without permission of
Upper Control Limit: A horizontal line on a control chart (usually dotted) which Represents the Upper Limits of Process Capability. Variable: A characteristic that may take on different values. Variables Data: Numerical measurements made at the interval or ratio level; quantitative data, e.g., ohms, voltage, diameter; subdivisions of the measurement scale are conceptually meaningful, e.g., 1.6478 volts. Variation: Any quantifiable difference between individual measurements; such differences can be classified as being due to common causes (random) or special causes (assignable). X and R Charts: A control chart which is a representation of process capability over time; displays the variability in the process average and range across time. 2-29 Do Not Reprint without permission of
Notes 2-30 Do Not Reprint without permission of
Notes 2-31 Do Not Reprint without permission of