Notes: Internet Username Password (Sealed Envelope) Modem login Password Wi-Fi access password Home Broadband Home Broadband Indoor Modem 19 User Guide HBI-200 (Windows and Mac) Version 2.0
Index 1. Product overview 2 2. Getting to know your Modem 3 3. Home Voice 7 4. Home Broadband and Voice (with a Wi-Fi Configuration) 11 5. Troubleshooting guide 17 Product overview Thank you for purchasing your Home Broadband Indoor Modem herein after referred to as Modem. It is a complete voice and data Modem with built-in Wi-Fi functionality allowing users to access internet wirelessly. Box contents The Indoor Modem package contains the following items: 1. Modem 2. Ethernet cable 3. Telephone cable 4. Power adapter 5. User Guide 6. Warranty card 1 2
Getting to know your Modem Front view 1 2 3 4 5 NO. Interface Status Description Notes: 3 Wi-Fi: Wireless Fidelity 4 1 2 WiMAX POWER 3 LAN 4 5 TEL Wi-Fi On Blink Off On Off On Blink Off On Blink Off On Blink Off The indicators indicate the signal strength of the WiMAX network. When all the LEDs are on, it indicates that the signal strength is at the highest level. One after the other in order Software upgrade is under progress. Please do not power off the modem or the software will be corrupted 2nd & 3rd LED from bottom Software is corrupted. Kindly use the recovery CD provided inside the box, and follow the instructions. There is no WiMAX network signal. The Modem is powered on. The Modem is powered off. The LAN port is being used. The data is being transmitted. The LAN port is unused. The TEL interface is being used. The TEL interface has an incoming call. The telephone connected to the TEL port is not working. The Wi-Fi function is enabled. Data is being transmitted. The Wi-Fi function is disabled.
Rear view NO. Interface Description 1 POWER The interface is used to connect to the power adapter. 2 TEL The interface is used to connect the telephone line. 3 LAN The interface is used to connect the Modem to the computer using an Ethernet cable. 4 RESET Caution: See later instructions on reset use. 5 External antenna Connection (not used). 6 5 4 6 Wi-Fi Press this button to enable or disable the Wi-Fi function. 3 2 1 5 6
Unpack your Modem Home Voice Note: Note: 7 8
Step 1 Place Modem near a window and connect the power cable and then connect to the power socket. After two minutes, check the LEDs (see image below). The number of LEDs lit up indicates the strength of the signal. When all the LEDs are lit up means you have an excellent signal. If less than three LEDs are lit, try placing the Modem at different locations. Sometimes turning the Modem a little can improve your signal strength. Step 3 Connect the telephone to the input labeled TEL using telephone cable supplied. Once you hear the dial tone you can start to make your voice calls. Step 2 the box, in case the Modem is accidentally moved. Note: showing signal strength on the Modem are stable before connecting the laptop or telephone, this typically takes up to two minutes. set is not required. Front Side 9 10
Please follow steps 1 to 3 Step 4 Home Broadband and Voice (with a Wi-Fi Configuration) Connect the Ethernet cable between your laptop and the LAN port on the Modem. 11 12
Step 5 In order to start using Home Broadband internet service, please enter your Username and password provided by Nawras as guided below. Step 6 http://192.168.1.1/ Step 7 Internet account (PPPoE): username@nawras.om subscription contract. Internet Account (PPPoE) Username Mabrook! Now you can surf the internet at your home. 13 14
Step 8 Establish a Wi-Fi Connection: You can remove the Ethernet cable between your laptop and the Modem. Now establish a wireless network connection between your laptop and the Modem. Firstly you may need to activate the wireless function on your laptop and then open View Available Wireless Networks. Select your Wi-Fi network name (SSID) and click Connect Enter the Wi-Fi access password (up to 10 characters), confirm and click OK. Step 9 To disable Wi-Fi functionality: If you wish to disable the Wi-Fi functionality and use the Broadband internet by directly connecting to the Modem using an Ethernet cable, please follow the steps 5 and 6 and press Disable button under Wi-Fi tab. WiFi Status Channel Security WiFi MAC SSID Security Key Enabled Auto WPA-PSK 00:0C:43:30:00:70 Apply Enable Disable 15 16
Troubleshooting guide Indoor Modem HBI-200 1. The power LED indicator is not ON. 2. The Modem power light is not ON or the WiMAX signal LEDs are not stable. 3. I am not able to make phone calls. 4. I am not able to browse the internet. 5. I am not able to connect using Wi-Fi. 17 18