ESP PANELS TM & SYSTEM COMPONENTS Instruction and connection manual
Panel range System monitoring Panel ESP-SYSTEM AC circuit breaker panel ESP-AC-20A-11 DC circuit breaker panel ESP-DC-20A-11 Blank panel ESP-BLANK SYSTEM MONITORING AC SYSTEM DC SYSTEM DC MONITORING volts amps 888 charge discharge 888 battery iso switch domestic start on off AC MONITORING volts amps 888 888 shore avail shore in use gen in use MULTI PLUS inverter on mains on 12 16 20 overload bulk 8 24 low battery absorp 4 28 temperature float 0 shore current limiter 30 on off charger only off on lights PANEL SYSTEMS AC SYSTEM DC SYSTEM VE.NET 88888 preheat start stop back enter VE.Net Panel ESP-VE.NET AC circuit breaker panel ESP-AC-20A-04 DC circuit breaker panel ESP-DC-20A-04 Control panel ESP- page 2 ESP PANELS
Connections to ESP DC Breaker Panel ESP DC Breaker Panel 0V from ESP System Panel (allows System Panel to control backlight) 20 A OR 0V from Boat supply 16A To 12V or 24V consumer (Battery +) DC Link Box 16A Note: Undo 2 x nuts to remove backlight PCB to allow fitting of Custom Window Label Alternate connection point for main supply. Both connections can be used. 9V from ESP System Panel (allows System Panel to control backlight) OR 9-30V from Boat supply To 12V or 24V consumer (Battery -) WARNING: Ensure all cables are correctly sized for the fuse or circuit breaker protecting them. Negative Busbar (not supplied) ESP PANELS page 3
Connections to ESP AC Breaker Panel - with single AC group ESP AC Breaker Panel 20 A 16A 0V from ESP System Panel (allows System Panel to control backlight) OR 0V from Boat supply To consumer (live) 16A Note: Undo 2 x nuts to remove backlight PCB to allow fitting of Custom Window Label RCD (not supplied) WARNING: The installer must ensure that the rear of the panel and live bus bar is inaccessible once installed. Ensure all cables are correctly sized for the fuse or circuit breaker protecting them. Alternate connection point for main supply. Both connections can be used. Neutral Busbar (not supplied) 9V from ESP System Panel (allows System Panel to control backlight) OR 9-30V from Boat supply To consumer (neutral) To consumer (earth) Earth Busbar (not supplied) All supply & consumer earths to this point page 4 ESP PANELS
Connections to ESP AC Breaker Panel - with two AC groups ESP AC Breaker Panel 0V from ESP System Panel (allows System Panel to control backlight) 20 A 16A OR 0V from Boat supply To high load consumer (live) High load group RCD (not supplied) Inverter group RCD (not supplied) WARNING: Cut busbar to separate high load and inverter load groups. A gap of at least 5mm is required. 16A Note: Undo 2 x nuts to remove backlight PCB to allow fitting of Custom Window Label To inverter load consumer (live) 9V from ESP System Panel (allows System Panel to control backlight) OR 9-30V from Boat supply WARNING: To high load consumer (neutral) The installer must ensure that the rear of the panel and live bus bar is inaccessible once installed. To inverter load consumer (neutral) Ensure all cables are correctly sized for the fuse or circuit breaker protecting them. Inverter group Neutral Busbar (not supplied) High load group Neutral Busbar (not supplied) To consumers (earth) Earth Busbar (not supplied) All supply & consumer earths to this point ESP PANELS page 5
Control Panel 9V from ESP System Panel (allows System Panel to control backlight) OR 9-30V from Boat supply 0V from ESP System Panel (allows System Panel to control backlight) OR 0V from Boat supply Note: A connection PCB is supplied loose. This allows alternate switch actions to be fitted prior to the connection PCB being soldered onto the switch. Your distributor can fit the PCB and switch at time of ordering. Note: Undo 4 x nuts to remove backlight PCB to allow fitting of Custom Window Label Switch capacity is 4 Amps max. Switch supplied is centre off momentary either way. Alternative switch actions can be purchased separately page 6 ESP PANELS
Indicatie led Indicatie led Indicatie led Connections to ESP System Contol Panel using Mark 2 DC Link Box ESP System Control Panel 9V+ for ESP DC & AC Breaker Panel backlight 0V- for ESP DC & AC Breaker Panel backlight DC Link Box phoenix Multicompact 12/1200/50 RJ45 RJ11 RJ45 ESP PowerMan RJ11 RJ11 ESP PANELS page 7
System Accessories Labelling ESP PowerMan The system panel acquires its AC voltage and current from the ESP PowerMan Unit. These provide automatic switching between shore power, generator and MultiPlus. In addition, high load circuits are disconnected when only Inverter power is available. Custom window labels The Breaker and Control Panels are designed to accept custom legends, to suit your needs. ESP PowerMan 20A Designed for systems with up to 5Kw generator and one MultiPlus unit. ESP PowerMan 32A Designed for systems with up to 8Kw generator and one or two MultiPlus units. ESP PowerMan 64A Designed for systems with up to 16Kw generator and two to four MultiPlus units Easy to use MS Word templates for these are available for download at: www.victronenergy.com DC Link Box The system panel acquires its DC voltage and current from the DC Link Box. The Link Box provides primary protection for heavy DC consumers and avoids spaghetti junction wiring at the battery terminal. Simply fill these in, print on Laser Film and cut to size. To install the label, remove the backlight PCB by undoing the securing nuts. Lay the label onto the rear of the window and reassemble. page 8 ESP PANELS
DC Link Box 888 888 888 888 ESP PANELS page 9
Indicatie led Indicatie led Indicatie led domestic on volts volts shore avail SYSTEM MONITORING DC MONITORING charge discharge start AC MONITORING shore in use amps battery iso switch on amps gen in use MULTI PLUS 16 12 inverter on mains on overload bulk 8 low battery absorp 4 temperature float 0 shore current limiter off charger only off on lights 20 off PANEL 24 30 28 AC SYSTEM DC SYSTEM Indicatie led Indicatie led Indicatie led domestic on volts volts shore avail SYSTEM MONITORING DC MONITORING charge discharge start AC MONITORING shore in use amps battery iso switch on amps gen in use MULTI PLUS 16 12 inverter on mains on overload bulk 8 low battery absorp 4 temperature float 0 shore current limiter off charger only off on lights 20 off PANEL 24 30 28 AC SYSTEM DC SYSTEM System In A Box schematic wiring diagrams SYSTEM IN A BOX with MultiPlus SYSTEM IN A BOX with Multi EasyPlus 888 888 888 888 Generator Max 5Kw (option) 888 888 Generator Max 3.6Kw (option) 888 888 phoenix Multicompact 12/1200/50 phoenix EasyaPlus 12/1600/70 ESP PowerMan - 20A RCD BOX ESP PowerMan - 20A Low Loads High Loads Low Loads High Loads Alternator (option) Cyrix battery separator (option) Alternator (option) Cyrix battery separator (option) DC Link Box DC Link Box Starter Motor (not included) Starter Motor (not included) Starter Battery (option) Service Battery (option) Starter Battery (option) Service Battery (option) page 10 ESP PANELS
ESP PowerMan 20A connection diagram - MultiPlus A A I I V 1 2 + - S - + VICTRON BMV 501 (Terminals marked A1 & A2) or VICTRON VE.Net BATTERY LER (Terminals marked NO relay contacts) VICTRON DUO MULTI PANEL RJ45 Cat 5 patch lead VICTRON MULTI PLUS 2 core 0.5mm2 or larger 2 core 0.5mm2 or larger 2 core 0.5mm2 or larger RJ45 Cat 5 patch lead PE N L AC IN PE N AC OUT L HIGH POWER DISTRIBUTION LOW POWER DISTRIBUTION SHORE POWER 3 core 4.0mm2 or larger GENERATOR Max 5Kw ESP PANELS page 11
ESP PowerMan 32A connection diagram A A I I V 1 2 + - S - + VICTRON BMV 501 (Terminals marked A1 & A2) or VICTRON VE.Net BATTERY LER (Terminals marked NO relay contacts) VICTRON DUO MULTI PANEL RJ45 Cat 5 patch lead VICTRON MULTI PLUS 2 core 0.5mm2 or larger 2 core 0.5mm2 or larger RJ45 Cat 5 patch lead PE N L AC IN PE N AC OUT L 3 core 4.0mm2 or larger 3 core 4.0mm2 or larger SHORE POWER 3 core 6.0mm2 or larger LOW POWER DISTRIBUTION HIGH POWER DISTRIBUTION 3 core 6.0mm2 or larger 3 core 6.0mm2 or larger 3 core 6.0mm2 or larger page 12 ESP PANELS
OPTIONAL SECOND - VICTRON MULTI PLUS Termination detail PE N AC IN L PE N AC OUT L 3 core 4.0mm2 or larger 3 core 4.0mm2 or larger GENERATOR Max 8Kw ESP PANELS page 13
ESP PowerMan 20A connection diagram - EasyPlus VICTRON DUO MULTI PANEL VICTRON EASY PLUS 2 core 0.5mm2 or larger Not normally used 2 core 0.5mm2 or larger RJ45 Cat 5 patch lead RJ45 Cat 5 patch lead PE N AC IN L PE N L PE N L AC OUT HIGH AC OUT LOW LOW POWER DISTRIBUTION HIGH POWER DISTRIBUTION SHORE POWER 3 core 4.0mm2 or larger GENERATOR Max 5Kw page 14 ESP PANELS
Product Dimensions ESP Panels: ESP PowerMan: ESP PowerMan 20A - 250mm(L) x 200mm(W) x 95mm(H) ESP PowerMan 32A - 380mm(L) x 300mm(W) x 120mm(H) ESP PowerMan 64A - 460mm(L) x 380mm(W) x 180mm(H) DC Link Box: Half size panels: VE.Net Panel ESP-VE.NET DC Link Box - 380mm(L) x 300mm(W) x 120mm(H) AC circuit breaker panel ESP-AC-20A-04 DC circuit breaker panel ESP-DC-20A-04 Full size panels: System monitoring Panel ESP-SYSTEM AC circuit breaker panel ESP-AC-20A-11 DC circuit breaker panel ESP-DC-20A-11 Control panel ESP- Blank panel ESP-BLANK All panels: 160mm(W) x 130mm(H) All panels: 160mm(W) x 260mm(H) ESP PANELS page 15
ESP PANELS TM Distributed by: Victron Energy B.V. De Paal 35, 1351 JG Almere-Haven P.O. Box 50016, 1305 AA Almere-Haven The Netherlands Tel. +31 (0)36 535 97 00 Fax +31 (0)36 531 16 66 (general + service) Fax +31 (0)36 535 97 40 (sales) E-mail sales@victronenergy.com www.victronenergy.com