8 766 7 MHz Dual Band 8', 65 Degree Antenna RET X-polarized (+45 and -45 ). UV resistant fiberglass radomes. Wideband vector dipole technology. DC Grounded metallic parts for impulse suppression. RET motor housed inside the radome and field replaceable. 698 894 MHz General specifications: Frequency range 698 894 MHz // 17 217 MHz Impedance 5 ohms VSWR <1.5:1 Intermodulation (2xw) IM:< - dbc Polarization +45 and -45 Connector 4 x DIN female (long neck) Isolation intrasystem > db // intersystem >5 db See reverse for order information. Horizontal pattern 17 217 MHz Vertical pattern electrical downtilt IRT specifications: Logical interface ex factory 1) AISG 1.1 Protocols AISG 1.1 and GPP/AISG 2. compliant Hardware interface 2) 2 x 8pin connector acc. IEC 1-9; according to AISG: RCUin (male): Control / Daisy chain in RCUout (female): Daisy chain out Power supply V Power Consumption <1 W (standby); <8.5 W (motor activated) Adjustment time (full range) 4 seconds Adjustment cycles >5, Certification FCC 15.7 Class B Computing Devices Horizontal pattern Vertical pattern electrical downtilt 1) The protocol of the logical interface can be switched from AISG 1.1 to GPP/AISG 2. and vice versa with a vendor specific command. Start-up operation of the RCU 8149 is possible in an RET system supporting AISG 1.1 or supporting GPP/AISG 2. after performing a layer 2 reset before address assignment. The protocol can also be changed as follows: AISG 1.1 to GPP: Enter "GPP" into the additional data filed "Installer s ID" and perform a layer 7 reset or a power reset. GPP to AISG 1.1: Enter "AISG 1" into the additional datafield "Installer s ID" and perform a layer 2 reset or a power reset. After switching the protocol any other information can be entered into the "Installer s ID" field. 2) The tightning torque for fixing the connector must be.5 1. Nm ( hand-tightened ). The connector should be tightened by hand only! Specifications: 698 86 MHz 824 894 MHz 17 1755 MHz 185 19 MHz 21 217 MHz Gain 16.4 dbi 16.8 dbi 18 dbi 18.5 dbi 18 dbi Front-to-back ratio > db (co-polar) > db (co-polar) >27 db (co-polar) >27 db (co-polar) >27 db (co-polar) 4 db (average) 4 db (average) 4 db (average) 4 db (average) 4 db (average) Maximum input power 5 watts (at 5 C) 5 watts (at 5 C) watts (at 5 C) watts (at 5 C) watts (at 5 C) per input +45 and -45 polarization 68 (half-power) 65 (half-power) 6 (half-power) 62 (half-power) 6 (half-power) horizontal beamwidth +45 and -45 polarization 9.5 (half-power) 8.7 (half-power) 5.8 (half-power) 5.8 (half-power) 5.8 (half-power) vertical beamwidth Electrical downtilt continuously adjustable Min sidelobe suppression for 5 T 5 T 5 T 5 T 5 T first sidelobe above main beam 16 16 16 db 18 18 16 db 18 18 18 db 18 18 18 db 18 18 18 db average 18 18 db db 22 db 22 db 22 db Cross polar ratio Main direction 25 db (typical) db (typical) 25 db (typical) db (typical) 25 db (typical) Sector ± > db, 15 db (avg) > db, 12 db (avg) >8 db, 15 db (avg) > db, 15 db (avg) >8 db, 15 db (avg) Tracking, avg. 1 db 1 db 1.5 db 1.5 db 1.5 db Squint ±2.5 ±2.5 ± ± ± 11225-C 96.415 Feb 22, 11 Kathrein Inc., Scala Division Post Office Box 458 Medford, OR 9751 (USA) Phone: (541) 779-65 Fax: (541) 779-991 Email: communications@kathrein.com Internet: www.kathrein-scala.com
8 766 7 MHz Dual Band 8', 65 Degree Antenna RET 64 mm M8 Mechanical specifications: Weight 58.4 lb (26.5 kg) Dimensions 96 x 11.8 x 6 inches (248 x x 152 mm) Wind load at 9 mph (kph) Front/Side/Rear 286 lbf / 6 lbf / 297 lbf (1 N) / (47 N) / (1 N) Mounting category H (Heavy) Wind survival rating* mph ( kph) Shipping dimensions 4.6 x 12.6 x 7.5 inches (2656 x x 1 mm) Shipping weight 71.6 lb (2.5 kg) Mounting Mounting hardware included for 2 to 4.6 inch (5 to 115 mm) OD masts. Mounting Brackets for use with 2-point mount antennas Mast dia. 2 4.5 inches (5 115 mm) Weight: 4.4 lb (2 kg) KATHREIN 8 149 Tested To Comply With FCC Standards This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: Refer to part number 8 149 for the specifications of the remote control actuator. 2.625 inches ±.125 (68 mm ± 4) 96 inches (248 mm) 97.2 inches (2469 mm) 98.8 inches (25 mm) Mechanical Tilt Brackets for use with 2-point mount antennas Weight: 1 lb (5.9 kg) (Model 85 7) 11.8 inches ( mm) 6 inches (152 mm) ircu out in ircu in out 698 894 45 698 894 +45 17 217 45 17 217 +45 Order Information: Model Description 8 766 Dualband antenna with mounting bracket // electrical downtilt 8 766 K Dualband antenna with mounting bracket and mechanical tilt bracket // electrical downtilt long neck 8pin male 8pin female long neck 8pin female 8pin male * Mechanical design is based on environmental conditions as stipulated in TIA-222-G-2 (December 9) and/or ETS 19-1-4 which include the static mechanical load imposed on an antenna by wind at maximum velocity. See the Engineering Section of the catalog for further details. All specifications are subject to change without notice. The latest specifications are available at www.kathrein-scala.com. Kathrein Inc., Scala Division Post Office Box 458 Medford, OR 9751 (USA) Phone: (541) 779-65 Fax: (541) 779-991 Email: communications@kathrein.com Internet: www.kathrein-scala.com
TECHNICAL SPECIFICATIONS AIR 21, 2.4M, B4A B12- B5P RADIO Active frequency band: Passive frequency band: Downlink EIRP: Uplink sensitivity: Remote electrical tilt: MIMO: Instantaneous bandwidth: Capacity (single standard per sector): Multi-RAT capability: Band 4 (17-1755 / 21-2155 MHz) Band 12 - Band 5 (698-894 MHz) 2 x 62 dbm (in bore-sight direction for the active band) TBD* -2 to -12, independently controlled per frequency band 2 x 2 for DL 4 RX branches to be used for diversity/ beam-steering /MIMO MHz Up to 4 carriers WCDMA with 2 x 2 DL MIMO Up to MHz LTE with 2 x 2 DL MIMO Single standard or two simultaneous standards (Capacity above is reduced for multi-rat) Bore-sight antenna gain for passive antenna option: 16.5 dbi Nominal beam-width, azimuth: 62 (active antenna) 67 (passive antenna) Nominal beam-width, elevation: 7.2 (active antenna) 9.2 (passive antenna) Additional antenna parameters: See Antenna characteristics, page MECHANICAL SPECIFICATION Weight (excl. mounting brackets): Size (H x W x D): Wind load: 55 kg for active and passive 244 x 7 x 2 mm 1 N / 57 N / 17 N (frontal/lateral/rear-side) @ 42 m/s wind speed INTERFACES AIR DU: DATA 1, Data 2: CPRI links (SFP modules with LC socket + flanges that match protective cover TYCO C611458) Power: - 48 V DC (TYCO/Ericsson RPT 447 4) Passive antenna: TX/RX 1, TX/RX 2: RF connectors ( female) SUPPORTING BASE-BAND RBS 61: One or two units depending on configuration. * 1 db better than best-in-class RRU connected to same size best-in-class antenna ** Other base-band configurations are available Telefonaktiebolaget LM Ericsson SE-126 25 Stockholm, Sweden Telephone +46 8 719 Fax +46 8 18 4 85 www.ericsson.com 15/287 1-FGB 1 558 Rev A Ericsson 12
RRUS 11 Dual PA RRU. Technical Data RBS Multi standard RF: 2x Watts Carrier BW: 1.4 MHz Alarms: 2 Dimensions (with sunshield): Width: 17. in Height: 17.8 in Depth: 7.2 in Weight: 55 lbs (Band 12) Weight: 5 lbs (Band 4) Temperature: -4 to +11 F Cooling: Self convection Power: -48 VDC Rec. fuse size Amp Rec. DC cable: 6 mm 2 up to meters mm 2 over meters Shielded Power Cons: Watts typ. Ericsson Inc Commercial in confidence Page 1 pa1-5-1
RRUS-11 I/F RBS Co-site & x-connect ports: SMA SFP port with LC connector Ethernet Maintenance port Protected ground M8 stud RF feeder 7/16 RET & external alarm ALD connector -48 V DC Power using 2*6 or 2* screw plint Ericsson Inc Commercial in confidence Page 2 pa1-5-1