Rev.: 000809 Update Alert: Firmware updates are posted to the web on a regular basis. We recommend that you check for firmware and/or install guide updates prior to installing this product. Installation Guide XK05-PKTI a programmable immobilizer data override interface compatible with Ford, Lexus, Lincoln, Mazda, Mercury, Pontiac, Scion and Toyota vehicles. Index Vehicle Application Guide... Installation Type - Toyota Lexus Vehicles... Type - Ford Mazda Vehicles... Wiring Connection Reference Chart... Programming Type - Toyota Lexus Vehicles...... Type - Ford Mazda Vehicles... LED Diagnostics and Troubleshooting... Warranty... 0 05 06 07 08 09 0 Ford, Lexus, Lincoln, Mazda, Mercury, Pontiac, Scion Toyota are registered trademarks and property of their respective companies. TECHNICAL SUPPORT / INFORMATI web resources: www.xpresskit.com www.xpressvip.com www.directechs.com 00 Directed Electronics. All rights reserved.
Vehicle Application Guide Vehicles 0 00 009 008 007 006 005 00 00 00 00 000 Ford Crown Victoria Econoline Edge Escape Escape Hybrid E-Series Excursion Expedition Explorer Explorer Sport Trac F50 F50 F50 F50 Five Hundred Flex Focus Freestar Freestyle Fusion GT Mustang Ranger Sport Trac Taurus Taurus X Thunderbird Transit Connect Windstar Lexus ES 0 W ES 50 W GS 00 W GS 50 W GS 0 W GS 50h W GS 60 W GX70 W IS 50 W IS 50 W LS 0 W LX70 W LX 570 W 0 W 50 W 00h W KI-Keysense Output (-) PK-Immobilizer Bypass- Data No Key Req'd Rev.: 000809 Page Legend: : Installation Types. W: Wire-to-Wire (WW). : WW DD (Data-to-Data). KI: Key Switch Interface. PK: Transponder Immobilizer Override. 00 Directed Electronics. All rights reserved.
Rev.: 000809 Page Vehicles 0 00 009 008 007 006 005 00 00 00 00 000 Lincoln Aviator LS Mark LT MKS MKX MKZ Navigator Town Car Zephyr Mazda * * 5 6 * * Atenza Axela B-Series CX-7 CX-9 MazdaSpeed MazdaSpeed6 MX-5 Miata -8 Tribute Mercury Grand Marquis Marauder Mariner Mariner Hybrid Milan Montego Monterey Mountaineer Sable Pontiac Vibe W Scion tc W xb W xd W KI-Keysense Output (-) PK-Immobilizer Bypass- Data No Key Req'd Legend: : Installation Types. W: Wire-to-Wire (WW). : WW DD (Data-to-Data). KI: Key Switch Interface. PK: Transponder Immobilizer Override. * Module is not compatible with Smart Keys. 00 Directed Electronics. All rights reserved.
Rev.: 000809 Page Vehicles 0 00 009 008 007 006 005 00 00 00 00 000 Toyota** Runner W Avalon W Camry W Corolla W FJ Cruiser W Highlander W Highlander Hybrid W Land Cruiser W Land Cruiser 00 W Matrix W RAV W Sequoia W Sienna W Solara W Tacoma W Tundra W Venza W Yaris W KI-Keysense Output (-) PK-Immobilizer Bypass- Data No Key Req'd Legend: : Installation Types. W: Wire-to-Wire (WW). : WW DD (Data-to-Data). KI: Key Switch Interface. PK: Transponder Immobilizer Override. ** This software is not compatible with 00 Toyota vehicles with G-stamped keys. 00 Directed Electronics. All rights reserved.
Installation Type For Toyota Lexus vehicles. Rev.: 000809 Page 5 Regular connections at ignition switch are required. (-) (+) V Input Parking Lights (+) Start (+) (+) Accessory (-) Neutral Safety (DEI Platforms Only) Starter Remote (-) GWR (status) Output Option A: Firmware upgrades (XKDD65). Option B: Range Extender connection (HARDD Rev. ). Option C: Plug DD harness directly into remote starter. (-) (+) V XK05 0 : (+) V : : (-) : : Brown: (-) GWR (status) Input : Green: (-) Key Sense Output 5: Violet: Output 8: Orange: Output 9: Red: (+) V Input 0: Black: (-) Chassis +VDC E5 White Connector Programming Button 5 6 7 T9 Black These connectors are located at the ignition switch. For security reasons, WW is disabled when using DD. To re-enable WW, the module has to be re-flashed. Not required in DD mode. 00 Directed Electronics. All rights reserved.
Installation Type For Ford Mazda vehicles. Regular connections at ignition switch are required. (-) (+) V Input Parking Lights (+) Start (+) (+) Accessory (-) Neutral Safety (DEI Platforms Only) Starter Remote (-) GWR (status) Output Rev.: 000809 Page 6 You will need valid keys to program the module in Ford Mazda vehicles. Option A: Firmware upgrades (XKDD65). Option B: Range Extender connection (HARDD Rev. ). Option C: Plug DD harness directly into remote starter. (-) (+) V XK05 0 : (+) V : : (-) : : Brown: (-) GWR (status) Input 5: Violet: Output 8: Orange: Output 9: Red: (+) V Input 0: Black: (-) Chassis +VDC Programming Button For security reasons, WW is disabled when using DD. To re-enable WW, the module has to be re-flashed. Not required in DD mode. A B C Description Description Description D E Description Description Refer to the next page for more information on connectors corresponding to each vehicle. 00 Directed Electronics. All rights reserved.
Wiring Connection Reference Chart Vehicles 0 00 009 008 007 006 005 00 00 00 00 000 Ford Crown Victoria E E E E E E C C Econoline B B B Edge D D D D Escape B B B B B B B B B B Escape Hybrid B B B B B B E-Series C C C Excursion A A Expedition B B B B B B B B B Explorer E E E E E B B B B Explorer Sport Trac B B B B B F50 B B B B B B B F50 B B B B F50 B B B B F50 E E E E Five Hundred E E E Flex B B B Focus B B B B B B B B B B B Freestar C C C C Freestyle C C C Fusion E E E E E GT B B Mustang E E E E E E Ranger C C C C C C C C C C Sport Trac E E E E Taurus A A A A A A A A A A A Taurus X A A Thunderbird B B B Transit Connect D Windstar C A A* Lincoln Aviator B B B LS B B B B B B B Mark LT B B B MKS E E MKX E E E E MKZ E E E E Navigator B B B B B B B B B Town Car E E E E E E C C Zephyr E Mercury Grand Marquis E E E E E E C C Marauder C C Mariner B B B B B B Mariner Hybrid B B B B B B Milan E E E E E Montego E E E Monterey C C C C Mountaineer E E E E E B B B B A* Sable A A A A A A A A Vehicles B A C D E Description Description Description Description Description Rev.: 000809 Page 7 0 00 009 008 007 006 005 00 00 00 00 000 Mazda D** D** D D D D D 5 D D D D D 6 D** D** D D D D D D Atenza D D D D D D D D Axela D D D D D D D B-Series C C C C C C C C C CX-7 D D D D CX-9 D D D D MazdaSpeed D D D D D MazdaSpeed6 D D D MX-5 Miata E E E E E -8 D D D D D D D Tribute B B B B B B * Built after -July-000. ** No Smart Keys. 00 Directed Electronics. All rights reserved.
HOLD Platform: XK05 Rev.: 000809 Programming Type For Toyota Lexus vehicles. Non Push-to-Start Vehicles When the module is plugged in, the LED will turn and stay. Insert a valid key into the ignition switch. Once the key is inserted, the LED on the module will flash quickly and will then turn, indicating that it has been successfully programmed. Push-to-Start Vehicles 5 Open the OEM remote, remove the circuit board and remove the battery. Verify that there is no other OEM remote near the vehicle, then place the circuit board agains the Push-to-Start button. When the module is plugged in, the LED will turn and stay. Press and hold the Push-to-Start button. The LED will start flashing to indicate that the module is in learning mode. The LED will turn once the module is programmed. Release the Push-to-Start button and reassemble the remote. To reset the module, you will need to re-flash it first. Flashes Quickly Off Off KEY Insert Key KEY Page 8 Solid Red Remove Key If the red LED stays solid, remove the key and repeat step. However, if the LED turns solid red for seconds and then turns, the module is already programmed. If the red LED stays solid, remove the key and repeat step. However, if the LED turns solid red for seconds and then turns, the module is already programmed. ENGINE STOP PUSH ENGINE STOP ENGINE STOP Solid Red Flashes RELEASE 00 Directed Electronics. All rights reserved.
Programming Type For Ford Mazda vehicles. Rev.: 000809 Page 9 You will need valid keys to program the module in Ford Mazda vehicles. Additional step for vehicles equipped with a SmartKey: 5 Remove keys from all SmartKeys and keep the cards away from the vehicles. Remove the cap from the ignition switch. When the module is plugged in, the LED will turn and stay. if the LED turns solid red for seconds and then turns, the module is already programmed. Insert the first valid key into the ignition switch and turn it to the position until the security light turns. Remove the first valid key. Wait for seconds following step. Insert the second valid key into the ignition switch and turn it to the position until the security light turns. Remove the second valid key. Wait for 5 seconds following step. Automatic transmission: Remote start the vehicle using the transmitter. Manual transmission: Apply the Brown wire (-) GWR to ground and the (+) V to the vehicle s ignition wire using a jumper wire. The LED will turn once the module is programmed. Remove the jumper wire if applicable. To reset the module, you will need to re-flash it first. KEY # Insert Key KEY # Insert Key KEY # Solid Red Remove Key KEY # Remove Key Jumper wire to +v Off Troubleshooting: A. If the LED stays solid or flashes rapidly, reverse the and wire connections. B. If the module fails to program or was previously used on another vehicle, then re-flash the module. 00 Directed Electronics. All rights reserved.
LED Diagnostics and Troubleshooting Rev.: 000809 Page 0 LED Status Description Troubleshooting During Power Up Off Module has no pow er. Make sure the DD harness is connected or the V is present betw een the red and black w ires. Solid red Module has pow er (the 0-pin harness w as connected) and w aits for the key to be Normal operation. turned to the position. If programmed to the current car: normal operation. Solid red x Module is already programmed to a car. If programmed to a different car, re-flash the seconds, then Off module and start over. Normal Operation Off Module programming is complete. Normal operation. Solid red GWR is now active. Normal operation. 00 Directed Electronics. All rights reserved.
Limited One-Year Consumer Warranty Rev.: 000809 Page For a period of E YEAR from the date of purchase of a Directed Electronics remote start or security product, Directed Electronics. ( DIRECTED ) promises to the original purchaser, to repair or replace with a comparable reconditioned piece, the security or remote start accessory piece (hereinafter the Part ), which proves to be defective in workmanship or material under normal use, provided the following conditions are met: the Part was purchased from an authorized DIRECTED dealer; and the Part is returned to DIRECTED, postage prepaid, along with a clear, legible copy of the receipt or bill of sale bearing the following information: consumer s name, address, telephone number, the authorized licensed dealer s name and complete product and Part description. This warranty is nontransferable and is automatically void if the Part has been modified or used in a manner contrary to its intended purpose or the Part has been damaged by accident, unreasonable use, neglect, improper service, installation or other causes not arising out of defect in materials or construction. TO THE MAXIMUM EXTENT ALLOWED BY LAW, ALL WARRANTIES, INCLUDING BUT NOT LIMITED TO EXPRESS WARRANTY, IMPLIED WARRANTY, WARRANTY OF MERCHANTABILITY, FITNESS FOR PARTICULAR PURPOSE AND WARRANTY OF N INFRINGEMENT OF INTELLECTUAL PROPERTY, ARE EXPRESSLY EXCLUDED; AND DIRECTED NEITHER ASSUMES NOR AUTHORIZES ANY PERS OR ENTITY TO ASSUME FOR IT ANY DUTY, OBLIGATI OR LIABILITY IN CNECTI WITH ITS PRODUCTS. DIRECTED HEREBY DISCLAIMS AND HAS ABSOLUTELY NO LIABILITY FOR ANY AND ALL ACTS OF THIRD PARTIES INCLUDING DEALERS OR INSTALLERS. IN THE EVENT OF A CLAIM OR A DISPUTE INVOLVING DIRECTED OR ITS SUBSIDIARY, THE PROPER VENUE SHALL BE SAN DIEGO COUNTY IN THE STATE OF CALIFORNIA. CALIFORNIA STATE LAWS AND APPLICABLE FEDERAL LAWS SHALLAPPLY AND GOVERN THE DISPUTE. THE MAXIMUM RECOVERY UNDER ANY CLAIM AGAINST DIRECTED SHALL BE STRICTLY LIMITED TO THE AUTHORIZED DIRECTED DEALER S PURCHASE PRICE OF THE PART. DIRECTED SHALL NOT BE RESPSIBLE FOR ANY DAMAGES WHATSOEVER, INCLUDING BUT NOT LIMITED TO, ANY CSEQUENTIAL DAMAGES, INCIDENTAL DAMAGES, DAMAGES FOR THE LOSS OF TIME, LOSS OF EARNINGS, COMMERCIAL LOSS, LOSS OF ECOMIC OPPORTUNITY AND THE LIKE. NOTWITHSTANDING THE ABOVE, THE MANUFACTURER DOES ER A LIMITED WARRANTY TO REPLACE OR REPAIR AT DIRECTED S OPTI THE PART AS DESCRIBED ABOVE. Some states do not allow limitations on how long an implied warranty will last or the exclusion or limitation of incidental or consequential damages. This warranty gives you specific legal rights and you may also have other rights that vary from State to State. DIRECTED does not and has not authorized any person or entity to create for it any other obligation, promise, duty or obligation in connection with this Part.90-0007 07-06 This Interface kit / Data Bus Interface part has been tested on the listed vehicles. Other vehicles will be added to the select vehicle list upon completion of compatibility testing. Visit website for latest vehicle application guide. DISCLAIMER: Under no circumstances shall the manufacturer or the distributors of the bypass kit / data bus interface part(s) be held liable for any consequential damages sustained in connection with the part(s) installation. The manufacturer and it s distributors will not, nor will they authorize any representative or any other individual to assume obligation or liability in relation to the interface kit / data bus interface part(s) other than its replacement. N.B.:Under no circumstances shall the manufacturer and distributors of this product be liable for consequential damages sustained in connection with this product and neither assumes nor authorizes any representative or other person to assume for it any obligation or liability other than the replacement of this product only. PROTECTED BY U.S. PATENTS: 5,79,55; 6,0,60 B *;6,,00 B; 6,9,6 B; 6,75,7 B; 6,97,7 B; 6,6,876 B; 6,9,5 B; 6,59, B; 6,696,97 B; 6,756,885 B; 6,756,886 B; 6,77,67 B; 6,8,89 B; 6,9,750 B; 7,00,0 B; 7,05,80 B; 7,0,86 B; 7, 06,6 B; 7,06,7 B; 7,068,5 B; 7,05,679 B; CDN.PATENT:,0,8;,,99;,5,0;,5,0;,5,07;,5,08;,5,0;, 0, 97;,6,670;,5,089 EUROPEAN PATENT:,05,8 PAT.PENDING:,9,06; MADE IN CANADA 00 Directed Electronics. All rights reserved.