Exciting new fashionable design... POSEIDON REEF BRACELET INSTRUCTION GUIDE
Stringing POSEIDON REEF BRACELET SWAROVSKI ELEMENTS Article Product Group Article No. Amount Size Color Color Code Fancy Stones 4120 1 pc. 18x13 mm Greige F 284 Fancy Stones 4161 2 pcs. 27x9 mm Indicolite F 379 Fancy Stones 4161 1 pc. 27x9 mm Jonquil F 213 Fancy Stones 4161 1 pc. 27x9 mm Olivine F 228 Beads 5000 1 pc. 6 mm Greige 284 Beads 5000/B 20 pcs. 10 mm Marbled Black 653 Beads 5000 20 pc. 10 mm Black Diamond 215 Supplies & Tools Supplies 21x Crimping Bead, black, 2mm 2x Crimping tube, black, 1mm French wire, black, 2cm 1x Headpin, Silver 1x Jump ring, black, 5mm 1x Jump ring, black, 6mm 5x Jump ring, black, 12mm 1x Setting: 4120/S H20, 18x13mm 4x Setting: 4161/S H20, 27x9mm 1x T clasp, black, 22mm Tiger tail, gray 0.3mm, 70cm Tools Chain nose pliers Crimping pliers Flat nose pliers Round nose pliers Side cutter Tweezers STEP 1: Place the Fancy Stones from the SWAROVSKI ELEMENTS assortment into the settings and press the prongs gently with the tweezers so that the crystals are secure. Repeat: x3 STEP 2: Cut two 35 cm pieces of the tiger tail and string on the SWAROVSKI ELEMENTS you see in the illustration. Don t go through the last hole of the first and last setting. The crystals should be positioned in the middle of the tiger tail. Turn the bracelet over, slide a big Crimping Bead onto each end on the right side and flatten the Beads with the chain nose pliers as shown. 0.3mm 35cm x2
STEP 3: Slide a small crimping tube, then a large crimping bead onto each end on the left side of bracelet. Push the small crimping tube slightly it should be so flat that you can put it under the metal of the setting as a space keeper it shouldn t be fixed! Pull tight so that the Crimping Beads on the right side are also under the metal of the settings then pull very tight, so that there is nearly no space between the settings as depicted in the illustration and fix the bracelet by flattening the larger crimping beads on the left side. Finally, string the tiger tail ends through the last hole of the first and last setting. Turn the bracelet over and slide on the SWAROVSKI ELEMENTS Ceramic Bead art. 5000/B, 10mm - Marbled Black as shown. 0.5cm x4 STEP 4: Cut four 0.5cm pieces of French wire. Slide three crimping beads onto the shorter wire end on the right side, then slide on the French wire. Go through a 12mm jump ring, back through the crimping beads and the last SWAROVSKI ELEMENTS Ceramic Bead. Pull tight and crimp the crimping tube as you see in the illustration. (Just crimp the Bead (directly before the French wire because the other two Crimping Beads are just space keepers, so the length of the wire on both ends will be the same.) 3 1/2 1 2 3
STEP 5: Repeat step 4 with the short string on the left side, using a 6 mm jump ring. On the shorter wire on the right side use just one crimping tube and the French wire. Then string the tiger tail through the 12mm jump ring, back through the crimping bead and through the last three Swarovski Ceramic Beads, pull tight and crimp the crimping bead correctly as shown. Finally, repeat this step with the remaining wire as shown in the illustration (you will be using just one crimping tube and the French wire and you will string the wire through the 6 mm jump ring). Repeat step 4: 3 1/2 1 2 3 STEP 6: Open the 5mm jump ring with the flat nose pliers, attach it onto the T clasp and close it over the 6mm jump ring of the bracelet.
STEP 7: Attach the remaining 12mm jump rings onto the right side of the bracelet as shown in the illustration. Open and close the jump rings sideways with the flat nose pliers. STEP 8: Slide the Swarovski Bead art. 5000 Greige onto the headpin and bend the headpin with the flat nose pliers at a 90 degree angle after the Bead. Form a loop with the round nose pliers; wrap the wire back twice as shown in the illustration and cut off any excess headpin wire. STEP 9: Open the last 12mm jump ring of the extension chain, attach the beaded headpin and close the jump ring.