. General Description The is a Color Active Matrix with an integral Cold Cathode Fluorescent Lamp(CCFL) back light system. The matrix employs asi Thin Film Transistor as the active element. It is a transmissive type display operating in the normally white mode. This TFTLCD has a 3.3 inch diagonally measured active display area with XGA resolution(768 vertical by 04 horizontal pixel array). Each pixel is divided into Red, Green and Blue subpixels or dots which are arranged in vertical stripes. Gray scale or the brightness of the subpixel color is determined with a 6bit gray scale signal for each dot, thus, presenting a palette of more than 6,44 colors. The has been designed to apply the interface method that enables low power, high speed low EMI. Flat Link must be used as a LVDS(Low Voltage ing) chip. The is intended to support applications where thin thickness, low power are critical factors and graphic displays are important. In combination with the vertical arrangement of the subpixels, the characteristics provide an excellent flat panel display for office automation products such as Notebook PC. CN FlatLink interface Timing Control Block Power Block Row Driver circuit Column driver circuit TFTLCD (04? 768) CN Backlight Ass y General Features Active screen size Outline dimensions Pixel pitch Pixel format Color depth Luminance, White Power Consumption Weight Display operating mode Surface treatments 4. inches(33.78cm) diagonal 98.5(H) 7.5(V) 5.8(D) mm (typ) 0.79 mm 0.79 mm 04 horiz. By 768 vert. pixels RGB stripe arrangement 6bit, 6,44 colors 0 cd/m (typ) Total 4.97Watt(typ) 590g (max) transmissive mode, normally white hard coating(3h), antiglare treatment of the front polarizer Ver. AUG. 9, 000 Page /6
. Electrical Specifications. Electrical Characteristics The requires two power inputs. One is employed to power the LCD electronics and to drive the TFT array and liquid crystal. The second input which powers the CCFL, is typically generated by an inverter. The inverter is an external unit to the LCD. Parameter MODULE: Power Supply Input Voltage Power Supply Input Current Differential Impedance Power Consumption Rush current Table ELECTRICAL CHARACTERISTICS: Values Symbol Min. Typ. Max. V CC I CC Zm P c I RUSH 3.0 90 3.3 0.40 00.35.5 3.6 0.60 0.05.8 Units Vdc A ohm Watts A Notes 3 LAMP Operating Voltage Operating Current Established Starting Voltage at 5 at 0 Operating Frequency Power Consumption Life Time V BL I BL f BL P BL 680 3.0 40 0,000 75 5.0 60 3.63 850 6.0 70 450 80 4.08 V RMS ma V RMS V RMS khz Watts Hrs Notes:. The specified current and power consumption are under the Vcc = 3.3V, 5, fv = 60Hz condition whereas Black pattern is displayed.. This impedance value is needed to proper display and measured form LVDS Tx to the mating connector. 3. The duration of rush current is about 0ms. 4. The variance of the voltage is 0%. 5. The transformer output voltage in the inverter must be high considering to the loss of the ballast capacitor in the inverter. 6. The lamp power consumption shown above does not include loss of external inverter. 7. The life time is determined as the time at which brightness of lamp is 50% compare to that of initial value at the typical lamp current on condition of continuous operating at 5 4 5 6 7 Ver. AUG. 9, 000 Page /6
. Interface Connections This LCD employs two interface connections, a 0 pin connector is used for the module electronics and the other connector is used for the integral backlight system. The electronics interface connector is a model FISEB0PHF manufactured by JAE or equivalent. The pin configuration for the connector is shown in the table below. Table MODULE CONNECTOR PIN CONFIGURATION (LVDS) [CN] Pin Symbol Description Notes 3 4 5 6 7 8 9 0 3 4 5 6 7 8 9 0 VCC VCC A0M A0P AM AP AM AP CLKM CLKP NC NC Power (3.3V) Power (3.3V) No Connection No Connection. Interface chips. LCD : FPD8530(National Semiconductor). Connector. LCD : 50040R(UJU Electronics). Mating JAE : FISE0MHF(FPC type) JAE : FISE0SHF(Wire type).3 Connector pin arrangement No. 0 CN CN The backlight interface connector is a model BHSR0VS, manufactured by JST. The mating connector part number is SM0BBHSS or equivalent. The pin configuration for the connector is shown in the table below. Table 3 BACKLIGHT CONNECTOR PIN CONFIGURATION [CN] Pin Symbol Description Notes HV LV Power supply for lamp (High voltage side) Power supply for lamp (Low voltage side) Notes:. The high voltage side terminal is colored pink.. The low voltage side terminal is colored black. Ver. AUG. 9, 000 Page 3/6
<FRONT VIEW> Notes. Unspecified dimensional tolerance are 0.5mm Ver. AUG. 9, 000 Page 4/6
< REAR VIEW > Ver. AUG. 9, 000 Page 5/6
3.PRECAUTIONS The LCD Products listed on this documents are not suitable for use of Military,Industry,Medical etc. system. If customers intend to use these LCD products for above application, Please contact ours sales people in advance. Ver. AUG. 9, 000 Page 6/6