MODEL NO.: G104X1 - L04

Transcription

1 Issued Date Jan. 4, 2 Model No. G4X-L4 TFT LCD Specification MODEL NO. G4X - L4 Customer Approved by Note APPL yhchang Director Accept /26 Version 2.

2 Issued Date Jan. 4, 2 Model No. G4X-L4 - CONTENTS - REVISION HISTORY GENERAL DESCRIPTION OVERVIEW.2 FEATURES.3 APPLICATION.4 GENERAL SPECIFICATIONS.5 MECHANICAL SPECIFICATIONS 2. ABSOLUTE MAXIMUM RATINGS ABSOLUTE RATINGS OF ENVIRONMENT 2.2 ELECTRICAL ABSOLUTE RATINGS 2.2. TFT LCD MODULE LED CONVERTER 3. ELECTRICAL CHARACTERISTICS TFT LCD MODULE 3.2 LED CONVERTER 4. BLOCK DIAGRAM TFT LCD MODULE 5. INTERFACE PIN ASSIGNMENT TFT LCD MODULE 5.2 BACKLIGHT UNIT 5.3 COLOR DATA INPUT ASSIGNMENT 6. INTERFACE TIMING INPUT SIGNAL TIMING SPECIFICATIONS 6.2 POWER ON/OFF SEQUENCE 6.3 THE INPUT DATA FORMAT 6.4 SCANNING DIRECTION 7. OPTICAL CHARACTERISTICS TEST CONDITION 7.2 OPTICAL SPECIFICATIONS 8.RELIABILITY TEST CRITERIA PACKAGING PACKING SPECIFICATIONS 9.2 PACKING METHOD. DEFINITION OF LABELS PRECAUTIONS ASSEMBLY AND HANDLING PRECAUTIONS.2 SAFETY PRECAUTIONS 2. MECHANICAL CHARACTERISTIC /26 Version 2.

3 Issued Date Jan. 4, 2 Model No. G4X-L4 REVISION HISTORY Version Date Page (New) Section Description. 2. 2//4 All All specification was first issued 3/26 Version 2.

4 Issued Date Jan. 4, 2 Model No. G4X-L4. GENERAL DESCRIPTION. OVERVIEW G4X- L4 is a.4 TFT Liquid Crystal Display module with LED backlight unit and 3-pin-and-ch LVDS interface. This product supports 24 x 768 XGA format and can display true 6.2M colors (6-bits colors with FRC). The converter module for LED backlight is built-in..2 FEATURES - Excellent brightness (5 nits) - Ultra high contrast ratio (2) - Fast response time (Ton+Toff average 25 ms) - High color saturation NTSC 57% - XGA (24 x 768 pixels) resolution - DE (Data Enable) only mode - LVDS (Low Voltage Differential Signaling) interface - Ultra wide viewing angle 76(H)/ 76(V) (CR>) Super MVA technology -8 degree rotation display option -LED Light Bar Replaceable -Wide operation temperature.3 APPLICATION -TFT LCD monitor - Industrial applications.4 GENERAL SPECIFICATINS Item Specification Unit Note Active Area 2.4 (H) x 57.8 (V) (.4 diagonal) mm Bezel Opening Area 25.4 (H) x 6.8 (V) mm () Driver Element a-si TFT active matrix - - Pixel Number 24 x R.G.B. x 768 pixel - Pixel Pitch (Sub Pixel).685 (H) x.255 (V) mm - Pixel Arrangement RGB vertical stripe - - Display Colors 6.2 M color - Display Operation Mode Transmissive mode / Normally black - - Surface Treatment Anti Glare - - Total power consumption (typ) W typ Note () Please refer to the attached drawings for more information of front and back outline dimensions. 4/26 Version 2.

5 Issued Date Jan. 4, 2 Model No. G4X-L4.5 MECHANICAL SPECIFICATIONS Item Min. Typ. Max. Unit Note Horizontal (H) mm Module Size Vertical (V) mm () Depth (D) mm - Weight g - Note () Please refer to the attached drawings for more information of front and back outline dimensions. 2. ABSOLUTE MAXIMUM RATINGS 2. ABSOLUTE RATINGS OF ENVIRONMENT Item Symbol Value Min. Max. Unit Operating Ambient Temperature T OP ºC Storage Temperature T ST ºC Note () Temperature and relative humidity range is shown in the figure below. (a) 9 %RH Max. (Ta 4 ºC). (b) Wet-bulb temperature should be 39 ºC Max. (Ta > 4 ºC). (c) No condensation Note Relative Humidity (%RH) Operating Range 4 2 Storage Range Temperature (ºC) 5/26 Version 2.

6 Issued Date Jan. 4, 2 Model No. G4X-L4 2.2 ELECTRICAL ABSOLUTE RATINGS 2.2. TFT LCD MODULE Value Item Symbol Unit Note Min. Max. Power Supply Voltage VCC V () LED CONVERTER Item Symbol Value Min. Max. Unit Note Converter Voltage V i V (), (2) Enable Voltage EN V Backlight Adjust ADJ V Note () Permanent damage to the device may occur if maximum values are exceeded. Function operation should be restricted to the conditions described under Normal Operating Conditions. Note (2) Specified values are for LED light bar (Refer to 3.2 for further information). 3. ELECTRICAL CHARACTERISTICS 3. TFT LCD MODULE Ta = 25 ± 2 ºC Parameter Symbol Value Min. Typ. Max. Unit Note Power Supply Voltage V CC V () Rush Current I RUSH A (2) Power Supply Current White ma - Black ma (3) Power Consumption P L W LVDS differential input voltage VID - 6 mv - LVDS common input voltage VICM V - Note () The assembly should be always operated within above ranges. Note (2) Measurement Conditions +3.3V Q 2SK475 FUSE C3 Vcc (LCD Module Input) R uf 47K (High to Low) (Control Signal) SW R2 Q2 2SK47 +2V K VR 47K C2 C.uF uf 6/26 Version 2.

7 Issued Date Jan. 4, 2 Model No. G4X-L4 VCC rising time is 47us.9Vcc +3.3V.Vcc GND 47µs Note (3) The specified power supply current is under the conditions at Vcc = 3.3 V, Ta = 25 ± 2 ºC, f v = 6 Hz, whereas a power dissipation check pattern below is displayed. a. White Pattern b. Black Pattern Active Area Active Area c. Vertical Stripe Pattern R G B R G B B R G B R G B R B R G B R G B R R G B R G B Active Area 7/26 Version 2.

8 Issued Date Jan. 4, 2 Model No. G4X-L4 3.2 LED CONVERTER Ta = 25 ± 2 ºC Parameter Symbol Value Min. Typ. Max. Unit Note Converter Power Supply Voltage V i V (Duty %) Converter Power Supply Current I i Vi = 2V (Duty %) LED Power Consumption P LED Vi = 2V (Duty %) EN Control Level Backlight on V Backlight off V PWM Control Level PWM High Level V PWM Low Level V PWM Control Duty Ratio 2 % PWM Control Frequency f PWM Hz LED Life Time L L 5, Hrs (2) Note () LED current is measured by utilizing a high frequency current meter as shown below Note (2) The lifetime of LED is defined as the time when it continues to operate under the conditions at Ta = 25 ±2 and I LED = 8mA DC (LED forward current) until the brightness becomes 5% of its original value. And minimum LED lifetime is estimated and provided by Nichia in Japan. Input Power Pi Power Supply Vi, Ii GND Converter LED Backlight Unit 8/26 Version 2.

9 Issued Date Jan. 4, 2 Model No. G4X-L4 4. BLOCK DIAGRAM 4. TFT LCD MODULE RX(+/-) RX(+/-) RX2(+/-) RX3(+/-) RXCLK(+/-) VCC SEL 6/8 RPFI GND (JAE,FI-XB3SRL-HF) INPUT CONNECTOR TIMING CONTROLLER DC/DC CONVERTER & REFERENCE VOLTAGE SCAN DRIVER IC TFT LCD PANEL (24x3x768) DATA DRIVER IC Vi CONVERTER CONNECTOR (Connector, 928-,.mm, WTB, pin, Aces) Converter LED BACKLIGHT UNIT 9/26 Version 2.

10 Issued Date Jan. 4, 2 Model No. G4X-L4 5. INTERFACE PIN ASSIGNMENT 5. TFT LCD MODULE CN Connector Pin Assignment Pin No. Symbol Description Note VCC Power supply +3.3V - 2 VCC Power supply +3.3V - 3 VCC Power supply +3.3V - 4 GND Ground - 5 GND Ground - 6 GND Ground - 7 RPFI Reverse Panel Function (Display Rotation) ( 2 ) 8 NC No Connection - 9 NC No Connection - NC No Connection - LVDS 6/8 bit select function control, SEL6/8 Low or NC 8 bit Input Mode High 6bit Input Mode ( 2 ) 2 GND Ground - 3 NC No Connection - 4 GND Ground - 5 RX- Negative transmission data of pixel - 6 RX+ Positive transmission data of pixel - 7 GND Ground - 8 RX- Negative transmission data of pixel - 9 RX+ Positive transmission data of pixel - 2 GND Ground - 2 RX2- Negative transmission data of pixel 2-22 RX2+ Positive transmission data of pixel 2-23 GND Ground - 24 RXCLK- Negative of clock - 25 RXCLK+ Positive of clock - 26 GND Ground - 27 RX3- Negative transmission data of pixel 3-28 RX3+ Positive transmission data of pixel 3-29 GND Ground - 3 NC No Connection ( 2 ) Note () Connector Part No. JAE, FI-XB3SRL-HF or STARCONN, 93F3-BBA Note (2) Low stands for V. High stands for 3.3V. NC stands for No Connected. 5.2 BACKLIGHT UNIT (Converter connector pin) Pin Symbol Description Remark V i Converter input voltage 2V 2 V i Converter input voltage 2V 3 V i Converter input voltage 2V 4 V i Converter input voltage 2V 5 V GND Converter ground Ground 6 V GND Converter ground Ground 7 V GND Converter ground Ground 8 V GND Converter ground Ground 9 EN Enable pin 3.3V ADJ Backlight Adjust PWM Dimming Note () Connector Part No. 928-(ACES) or equivalent Note (2) User s connector Part No. 929-(ACES) or equivalent /26 Version 2.

11 Issued Date Jan. 4, 2 Model No. G4X-L4 /26 Version COLOR DATA INPUT ASSIGNMENT The brightness of each primary color (red, green and blue) is based on the 8-bit gray scale data input for the color. The higher the binary input, the brighter the color. The table below provides the assignment of color versus data input. Data Signal Red Green Blue Color R7 R6 R5 R4 R3 R2 R R G7 G6 G5 G4 G3 G2 G G B7 B6 B5 B4 B3 B2 B B Basic Colors Black Red Green Blue Cyan Magenta Yellow White Gray Scale Of Red Red() / Dark Red() Red(2) Red(253) Red(254) Red(255) Gray Scale Of Green Green() / Dark Green() Green(2) Green(253) Green(254) Green(255) Gray Scale Of Blue Blue() / Dark Blue() Blue(2) Blue(253) Blue(254) Blue(255) Note () Low Level Voltage, High Level Voltage

12 Issued Date Jan. 4, 2 Model No. G4X-L4 6. INTERFACE TIMING 6. INPUT SIGNAL TIMING SPECIFICATIONS The input signal timing specifications are shown as the following table and timing diagram. Signal Item Symbol Min. Typ. Max. Unit Note DCLK Frequency Fc MHZ Total Tv Th Tv=Tvd+Tvb Vertical Active Display Term Display Tvd Th - Blank Tvb Th - Total Th Tc Th=Thd+Thb Horizontal Active Display Term Display Thd Tc - Blank Thb Tc - Note () Since this assembly is operated in DE only mode, Hsync and Vsync input signals should be set to low logic level. Otherwise, this assembly would operate abnormally. (2) Frame rate is 6Hz INPUT SIGNAL TIMING DIAGRAM Tv Tvd Tvb DE Th DCLK DE Tc Thb Thd DATA Valid display data 2/26 Version 2.

13 Issued Date Jan. 4, 2 Model No. G4X-L4 6.2 POWER ON/OFF SEQUENCE To prevent a latch-up or DC operation of LCD assembly, the power on/off sequence should be as the diagram below..9vcc.9vcc.vcc VCC LVDS T T2 VALID 9% % T3 T7.VCC T4.9Vi.9Vi Vi.Vi.Vi T5 T6 9% BL ON/OFF % T8 T9 PWM DIMMING 9% % Power ON/OFF sequence Note () Please avoid floating state of interface signal at invalid period. Note (2) When the interface signal is invalid, be sure to pull down the power supply of LCD VCC to V. Note (3) The Backlight converter power must be turned on after the power supply for the logic and the interface signal is valid. The Backlight converter power must be turned off before the power supply for the logic and the interface signal is invalid. Parameter Value Min Typ Max Units T.5 - ms T2-5 ms T3-5 ms T ms T ms T ms T7 5-3 ms T8 - - ms T9 - - ms 3/26 Version 2.

14 Issued Date Jan. 4, 2 Model No. G4X-L4 6.3 The Input Data Format Note () R/G/B data 7 MSB, R/G/B data LSB Note (2) Please follow PSWG Signal Name Description Remark R7 Red Data 7 (MSB) Red-pixel Data R6 Red Data 6 Each red pixel's brightness data consists of these 8bits pixel data. R5 Red Data 5 R4 Red Data 4 R3 Red Data 3 R2 Red Data 2 R Red Data R Red Data (LSB) G7 Green Data 7 (MSB) Green-pixel Data G6 Green Data 6 Each red pixel's brightness data consists of these 8bits pixel data. G5 Green Data 5 G4 Green Data 4 G3 Green Data 3 G2 Green Data 2 G Green Data G Green Data (LSB) B7 Blue Data 7 (MSB) Blue-pixel Data B6 Blue Data 6 Each red pixel's brightness data consists of these 8bits pixel data. B5 Blue Data 5 B4 Blue Data 4 B3 Blue Data 3 B2 Blue Data 2 B Blue Data 4/26 Version 2.

15 Issued Date Jan. 4, 2 Model No. G4X-L4 B Blue Data (LSB) RXCLKIN+ LVDS Clock Input RXCLKIN- DE Display Sync VS Vertical Sync HS Horizontal Sync Note (3) Output signals from any system shall be low or Hi-Z state when VCC is off 6.4 Scanning Direction The following figures show the image see from the front view. The arrow indicates the direction of scan. RPFI = Low/floating; normal display (default) RPFI = high display with 8degree rotation 5/26 Version 2.

16 Issued Date Jan. 4, 2 Model No. G4X-L4 7. OPTICAL CHARACTERISTICS 7. TEST CONDITIONS Item Symbol Value Unit Ambient Temperature Ta 25±2 o C Ambient Humidity Ha 5± %RH Supply Voltage V CC 5 V Input Signal According to typical value in "3. ELECTRICAL CHARACTERISTICS" Inverter Current I L 8mA ma 7.2 OPTICAL SPECIFICATIONS The relative measurement methods of optical characteristics are shown in 7.2. The following items should be measured under the test conditions described in 7. and stable environment shown in Note (6). Item Symbol Condition Min. Typ. Max. Unit Note Contrast Ratio CR (2) Response Time T R ms T F - 6 ms (3) Center Luminance of White L C cd/m 2 (4) White Variation δw (7) Rx θ x =, θ Y =.67 - Red Ry Viewing angle at Gx normal direction Green Typ. Typ. Color Gy (6) Chromaticity Bx Blue By.87 - Wx.33 - White Wy θ x Horizontal Viewing θ x CR Deg. () Angle θ Y Vertical θ Y /26 Version 2.

17 Issued Date Jan. 4, 2 Model No. G4X-L4 Note () Definition of Viewing Angle (θx, θy) Viewing angles are measured by BM5A Normal θx = θy = º θy- θy+ θx- = 9º x- θx θx+ y+ 2 o clock direction θy+ = 9º 6 o clock θy- = 9º y- x+ θx+ = 9º Note (2) Definition of Contrast Ratio (CR) The contrast ratio can be calculated by the following expression. Contrast Ratio (CR) = L255 / L L255 Luminance of gray level 255 L Luminance of gray level CR = CR (5), where CR (X) is corresponding to the Contrast Ratio of the point X at the figure in Note (7). Note (3) Definition of Response Time (T R, T F ) % 9% Gray Level 255 Gray Level 255 Optical Response % Gray Level %. T F T R Time 7/26 Version 2.

18 Issued Date Jan. 4, 2 Model No. G4X-L4 Note (4) Definition of Luminance of White (L C ) Measure the luminance of gray level 255 at center point and 5 points L C = L (5), where L (X) is corresponding to the luminance of the point X at the figure in Note (7). Note (5) Measurement Setup The LCD assembly should be stabilized at given temperature for 3 minutes to avoid abrupt temperature change during measuring. In order to stabilize the luminance, the measurement should be executed after lighting Backlight for 3 minutes in a windless room. LCD Module LCD Panel USB2 CS-2 Field of View = º Center of the Screen 5 mm Light Shield Room (Ambient Luminance < 2 lux) 8/26 Version 2.

19 Issued Date Jan. 4, 2 Model No. G4X-L4 Note (6) Definition of White Variation (δw) Measure the luminance of gray level 63 (255) at 5 points δw = Maximum [L (), L (2), L (3), L (4), L (5)] Minimum [L (), L (2), L (3), L (4), L (5)] Horizontal Line D D/4 D/2 3D/4 Vertical Line W W/4 W/2 2 5 X Test Point X= to 5 3W/4 3 4 Active Area 9/26 Version 2.

20 Issued Date Jan. 4, 2 Model No. G4X-L4 8. Reliability Test Criteria Test Item Test Condition Note High Temperature Storage Test 8ºC, 24 hours Low Temperature Storage Test -3ºC, 24 hours Thermal Shock Storage Test -2ºC,.5hour 7,.5hour; cycles, hour/cycle High Temperature Operation Test 7ºC, 24 hours () (2) Low Temperature Operation Test -3ºC, 24 hours High Temperature & High Humidity Operation Test 6ºC, 9%RH, 24hours Shock (Non-Operating) 5G, ms, half sine wave, time for ± X, ± Y, ± Z. (3) Vibration (Non-Operating).5G, ~ 3 Hz, min/cycle, 3 cycles each X, Y, Z (3) Note () There should be no condensation on the surface of panel during test. Note (2) Temperature of panel display surface area should be 8 ºC Max. Note (3) At testing Vibration and Shock, the fixture in holding the module has to be hard and rigid enough so that the module would not be twisted or bent by the fixture. 2/26 Version 2.

21 Issued Date Jan. 4, 2 Model No. G4X-L4 9. PACKAGING 9. PACKING SPECIFICATIONS () 8pcs LCD modules / Box (2) Box dimensions 465 (L) X 362 (W) X 34 (H) mm (3) Weight approximately.23 Kg (8 modules per box) 9.2 PACKING METHOD () Carton Packing should have no failure in the following reliability test items. Test Item Test Conditions Note Vibration ISTA STANDARD Random, Frequency Range 2 2 Hz Top & Bottom 3 minutes (+Z), min (-Z), Non Operation Right & Left minutes (X) Back & Forth minutes (Y) Dropping Test Angle, 3 Edge, 6 Face, 6 cm Non Operation Figure.9- packing method 2/26 Version 2.

22 Issued Date Jan. 4, 2 Model No. G4X-L4 Sea / Land Transportation (4ft Container) Air Transportation Figure. 9-2 Packing method 22/26 Version 2.

23 Issued Date Jan. 4, 2 Model No. G4X-L4.DEFINITION OF LABELS. CMO MODULE LABEL The barcode nameplate is pasted on each module as illustration, and its definitions are as following explanation. CHI MEI OPTOELECTRONICS G4X -L4 Rev.XX E27943 MADE IN TAIWAN X X X X X X X Y M D L N N N N RoHS (a) Model Name G4X-L4 (b) Revision Rev. XX, for example A, A B, B2 or C, C2 etc. (c) Serial ID X X X X X X X Y M D L N N N N Serial No. Product Line Year, Month, Date CMO Internal Use CMO Internal Use Revision CMO Internal Use Serial ID includes the information as below (a) Manufactured Date Year ~9, for 2~29 Month ~9, A~C, for Jan. ~ Dec. Day ~9, A~Y, for st to 3 st, exclude I,O, and U. (b) Revision Code Cover all the change (c) Serial No. Manufacturing sequence of product (d) Product Line -> Line, 2 -> Line 2, etc. 23/26 Version 2.

24 Issued Date Jan. 4, 2 Model No. G4X-L4. PRECAUTIONS. ASSEMBLY AND HANDLING PRECAUTIONS () Do not apply rough force such as bending or twisting to the module during assembly. (2) It is recommended to assemble or to install a module into the user s system in clean working areas. The dust and oil may cause electrical short or worsen the polarizer. (3) Do not apply pressure or impulse to the module to prevent the damage of LCD panel and Backlight. (4) Always follow the correct power-on sequence when the LCD module is turned on. This can prevent the damage and latch-up of the CMOS LSI chips. (5) Do not plug in or pull out the I/F connector while the module is in operation. (6) Do not disassemble the module. (7) Use a soft dry cloth without chemicals for cleaning, because the surface of polarizer is very soft and easily scratched. (8) Moisture can easily penetrate into LCD module and may cause the damage during operation. (9) High temperature or humidity may deteriorate the performance of LCD module. Please store LCD modules in the specified storage conditions. () When ambient temperature is lower than ºC, the display quality might be reduced. For example, the response time will become slow, and the starting voltage of backlight will be higher than that of room temperature. () Do not keep same pattern in a long period of time. It may cause image sticking on LCD..2 SAFETY PRECAUTIONS () The startup voltage of a Backlight is approximately Volts. It may cause an electrical shock while assembling with the inverter. Do not disassemble the module or insert anything into the Backlight unit. (2) If the liquid crystal material leaks from the panel, it should be kept away from the eyes or mouth. In case of contact with hands, skin or clothes, it has to be washed away thoroughly with soap. (3) After the module s end of life, it is not harmful in case of normal operation and storage. 2. MECHANICAL CHARACTERISTICS 24/26 Version 2.

25

26