Measuring Sensors PROUT SRIPTION
ontents: Optical distance sensors - Overview and advantages Special features of the optical distance sensors Sensor selection table ata sheets of the optical distance sensors Special features of the rotoscan RO-4 ata sheet rotoscan RO-4 ll rights reserved, especially the rights of copying and translation. opying or reproduction in any form requires prior written permission from Leuze electronic GmbH & o. KG Subject to changes due to technical progress.
Optical distance sensors Overview and advantages - Optical distance sensors with technology - Optical distance sensors with phase measurement technology - High flexibility through configuration - Reflection-independent distance information - High accuracy of measurement due to calibration / internal referencing - Light source L: measurement range from 25 1,400mm - Light source laser: measurement range from 20 30,000mm - nalogue output with current (4 20m) or voltage (1 10V) - igital RS 232 or RS 485 interface - Teachable switching outputs - Supply voltage 18 30V for sensors with analogue output - Supply voltage 10 30V for sensors with digital interface or switching outputs - M12 connector - Protection class IP 67 Innovative mounting system for rod mounting or mounting holes for screw mounting ccessories: - Mounting systems - P configuration software - onfiguration cable - onfiguration adaptor - onnectors 1
Special features of the optical distance sensors OS 25 - Optical triangulation distance sensor with technology - Light source: red light L - Measurement range: 25 200mm - nalogue voltage output 1 10V - Teachable and invertible analogue output (button and cable) - M12 connector - Plastic housing - Protection class IP 67 OSL 8 - Optical triangulation distance sensor with technology - Light source: red light laser - Measurement range: 20 500mm - nalogue voltage output 1 10V or analogue current output 4 20m - igital RS 232 or RS 485 interface - Teachable switching outputs - M12 connector (8-pin) - Robust metal housing - Protection class IP 67 dvantage 1: ompact construction dvantage 2: High measurement rate: measurement time < 10ms dvantage 3: Reflection-independent distance information dvantage 4: asy operation dvantage 1: ompact construction dvantage 2: Large measurement range dvantage 3: High accuracy of measurement dvantage 4: Reflection-independent distance information dvantage 5: High flexibility due to P-based configuration 2
OS 96 - Optical triangulation distance sensor with technology - Light source: red light/infrared L, red light laser - Measurement range: 60 5,000mm - nalogue voltage output 1 10V or analogue current output 4 20m - igital RS 232 or RS 485 interface - Teachable switching outputs - M12 connector (5-pin) - Robust metal housing with glass optics - Protection class IP 67 OSL 30 - Optical distance sensor with phase measurement technology - Light source: red light laser - Measurement range: 200 30,000mm - nalogue voltage output 1 10V or analogue current output 4 20m - igital RS 232 or RS 485 interface - Teachable switching outputs - M12 connector (8-pin) - Robust metal housing - Protection class IP 67 dvantage 1: onstruction with large measurement range dvantage 2: High accuracy of measurement dvantage 3: Reflection-independent distance information dvantage 4: High flexibility due to P-based configuration dvantage 1: Measurement range up to 30m dvantage 2: High accuracy of measurement due to internal referencing dvantage 3: Reflection-independent distance information dvantage 4: L display and key pad for configuration 3
Sensor selection table Operating principle esignation Measurement range Measurement time Resolution Light source Operating voltage L red light L infrared Laser red light Laser infrared 10 30V 18 30V OS 25/V-200-S12 25 200mm 5 10ms 1mm 22 28V 24V OSL 8/V4-45-S12 25 45mm 4 10ms 0.01mm OSL 8/4-45-S12 25 45mm 4 10ms 0.01mm OSL 8/V 66-200-S12 20 200mm 2 7ms 0.1 0.2mm OSL 8/V4-400-S12 20 400mm 4 10ms 0.1mm OSL 8/4-400-S12 20 400mm 4 10ms 0.1mm OSL 8/V 66-500-S12 20 500mm 2 7ms 0.1 0.5mm OSL 8/66-500-S12 20 500mm 2 7ms 0.1 0.5mm OS 96M/V-5000-600-220 100 600mm 10 50ms 0.1 0.5mm OS 96M/V-5000-600-420 100 600mm 10 50ms 0.1 0.5mm OS 96M/V-5010-600-221 100 600mm 10 50ms 0.1 0.5mm OS 96M/V-5010-600-421 100 600mm 10 50ms 0.1 0.5mm OS 96M/-5020-600-222 100 600mm 10 50ms 0.1 0.5mm OS 96M/-5020-600-422 100 600mm 10 50ms 0.1 0.5mm OS 96M/-5030-600-223 100 600mm 10 50ms 0.1 0.5mm OS 96M/-5030-600-423 100 600mm 10 50ms 0.1 0.5mm OS 96M/S-5040-600-224 100 600mm 10 50ms 0.1 0.5mm OS 96M/S-5040-600-424 100 600mm 10 50ms 0.1 0.5mm OS 96M/V-5400-420 100 600mm 10 50ms 0.1 0.5mm OS 96M/V-5290-426 120 1,400mm 10 50ms 0.1 1mm OS 96M/V-5310-426 120 1,400mm 10 50ms 0.1 1mm OS 96M/V-5420-421 120 1,200mm 10 100ms 0.1 1mm OS 96M/V-5140-420 60 2,000mm 10 100ms 1 5mm OS 96M/V-5130-421 60 2,000mm 10 100ms 1 5mm OS 96M/V-5060-220 200 2,000mm 10 100ms 1 3mm OS 96M/V-5060-420 200 2,000mm 10 100ms 1 3mm OS 96M/V-5070-221 200 2,000mm 10 100ms 1 3mm OS 96M/V-5070-421 200 2,000mm 10 100ms 1 3mm OS 96M/-5080-222 200 2,000mm 10 100ms 1 3mm OS 96M/-5080-422 200 2,000mm 10 100ms 1 3mm OS 96M/-5090-223 200 2,000mm 10 100ms 1 3mm OS 96M/-5090-423 200 2,000mm 10 100ms 1 3mm OS 96M/S-5100-224 200 2,000mm 10 100ms 1 3mm OS 96M/S-5100-424 200 2,000mm 10 100ms 1 3mm OSL 96K/V 66-2300-S12 150 2,300mm 2 7ms 1 5mm OSL 96K/66-2300-S12 150 2,300mm 2 7ms 1 5mm OS 96M/V-5510-420 250 5,000mm 10 100ms 1 20mm OS 96M/V-5480-421 250 5,000mm 10 100ms 1 20mm OS 96M/V-5520-426 250 5,000mm 10 100ms 1 20mm OS 96 M/6-600-S12 100 600mm 1 5ms 0.1 0.5mm OS 96 M/V6-600-S12 100 600mm 1 5ms 0.1 0.5mm OSR 96 M/6-600-S12 100 600mm 1 5ms 0.1 0.5mm OSR 96 M/V6-600-S12 100 600mm 1 5ms 0.1 0.5mm OSL 96 M/6-800-S12 150 800mm 1 5ms 0.1 0.8mm OSL 96 M/V6-800-S12 150 800mm 1 5ms 0.1 0.8mm OSL 96 M/6-2000-S12 150 2000mm 1 5ms 1 3mm OSL 96 M/V6-2000-S12 150 2000mm 1 5ms 1 3mm 4
Output Housing onnection Options Page igital nalogue PNP transistor NPN transistor RS 232 RS 485 / RS 422 thernet TP/IP urrent Voltage Plastic Metal M12 connector Terminals onnectors Teachable switching outputs P configuration Heating 9 11 13 15 19 21 23 27 31 31 31 31 33 33 33 33 35 35 37 39 39 41 43 43 45 45 45 45 47 47 47 47 49 49 51 55 59 59 59 61 61 63 63 65 65 67 67 5
Sensor selection table Operating principle esignation Measurement range Measurement time Resolution Light source Operating voltage OSL 30/V-30M-S12 200 30,000mm 30 100ms 0.1mm/1mm OSL 30/ 232-30M-S12 200 30,000mm 30 100ms 0.1mm/1mm OSL 30/ 485-30M-S12 200 30,000mm 30 100ms 0.1mm/1mm OSL 30/24-30M-S12 200 30,000mm 30 100ms 0.1mm/1mm L red light L infrared Laser red light Laser infrared 10 30V 18 30V 22 28V 24V RO-4 0 50,000mm 40ms 0.36 RO-4-06 0 50,000mm 40ms 0.36 RO-4-08 0 25,000mm 40ms 0.36 RO 4plus 0 50,000mm 40ms 0.36 RO 4-08plus 0 25,000mm 40ms 0.36 6
Output Housing onnection Options Page igital nalogue PNP transistor NPN transistor RS 232 RS 485 / RS 422 thernet TP/IP urrent Voltage Plastic 69 71 73 75 Metal M12 connector Terminals onnectors Teachable switching outputs P configuration Heating 79 79 79 81 81 7
OS 25 Optical distance sensors imensioned drawing 25 200mm 18-30 V nalogue voltage output 1 10V, teachable, can be inverted M 12 circular connector asy alignment through visible red light F Optical axis Transmitter Receiver L yellow, green Teach button Reference edge for the measurement (cover glass) lectrical connection We reserve the right to make changes ods_30e.fm I 60947... I 60947... ccessories: (available separately see page 82) IP 69K IP 67 able with M12 connector (K- ) M12 connectors (K, KS ) Mounting systems Leuze electronic GmbH + o. KG Post-box 1111-73277 Owen-Teck Tel. +49 7021 5730 www.leuze.de 8 OS 25/V-200-S12-04
OS 25 Specifications Optical data Measurement range 1) 25 200mm Resolution 1mm Light source L Wavelength 660nm (visible red light) Light spot 8x8mm 2 at 200mm Receiver line rror limits (relative to measurement range end value) 1) 2) Linearity ±2.5% Repeatability 2) ±2% b/w detection thresh. (6 90% rem.) ± 4% Timing Measurement time 5 10ms Response time 20ms elay before start-up 100ms lectrical data Operating voltage U 18 30V (incl. residual ripple) Residual ripple 15% of U ias current 25m Switching output nalogue output voltage 1 10V, R L 5kΩ Scanning range adjustment T II teach button or teach line (see remarks) Indicators L green ready L yellow object is located in the taught detection range; additional display functions of the Ls during the teach procedure - see remarks Mechanical data Housing plastic Optics cover plastic Weight 15g onnection type M12 connector, 4-pin nvironmental data mbient temp. (operation/storage) -20 +40 /-30 +70 Protective circuit 3) 2, 3 V safety class 4) II, all-insulated Protection class IP 67, IP 69K 5) L class 1 (acc. to N 60825-1) Standards applied I 60947-5-2 Options Teach input Input resistance 10 kω ± 10% ctive/not active U /0V or not connected 1) bsolute value measurement, luminosity coefficient 6 90%, 20, measurement object 50x50mm² 2) Same object, identical environmental conditions, measurement object 50x50mm² 3) 2=polarity reversal protection, 3=short-circuit protection for all outputs 4) Rating voltage 250V 5) IP 69K test acc. to IN 40050 part 9 simulated, high pressure cleaning conditions without the use of additives, acids and bases are not part of the test Order guide F rea not defined Linearity not defined Measurement range Object present No object detected Measurement distance esignation Part No. With M12 connector OS 25/V-200-S12 501 02824 Remarks T II teach-in via button Teach 1V analogue output Position the measured object at the desired distance. Press the teach button until the green L illuminates and the yellow L flashes. Release the teach button in the time window of 2 4s. Teach 10V analogue output Position the measured object at the desired distance. Press the teach button until the green L flashes and the yellow L illuminates. Release the teach button in the time window of 4 6s. T II teach-in via input Teach 1V analogue output Position the measured object at the desired distance. Teach input (PIN 2) to U until green L illuminates and yellow L flashes. isconnect the teach input or set to 0V in the time window 2 4s. Teach 10V analogue output Position the measured object at the desired distance. Teach input (PIN 2) to U until green L flashes and yellow L illuminates. isconnect the teach input or set to 0V in the time window 4 6s. Further notices Following a successful teach process, the yellow L illuminates within the taught measurement range. Permanent, fast flashing of Ls indicates an unsuccessful teach process (sensor continues to function with the old values, however). Remedy: Repeat teach process, activate teach button / teach input > 6s or de-energise sensor. Operate teach button with a blunt object. OS 25/V-200-S12-04 0706 9
OSL 8 Optical laser distance sensors imensioned drawing 25 45mm 18-30 V Reflection-independent distance information Highly insensitive to extraneous light nalogue current and voltage output Measurement range and mode adjustable Teachable switching output M12 turning connector F Receiver Transmitter Optical axis 90 turning connector L yellow, green Reference edge for the measurement (cover glass) lectrical connection We reserve the right to make changes ods_21e.fm I 60947... I 60947... ccessories: (available separately see page 84) Mounting systems onfiguration adaptor UPG 5 onfiguration software able with M12 connector (K- ) ontrol guard IP 69K IP 67 Leuze electronic GmbH + o. KG Post-box 1111-73277 Owen-Teck Tel. +49 7021 5730 www.leuze.de 10 OSL 8/V4-45-S12-05
OSL 8 Specifications Optical data Measurement range 1) 25 45mm Resolution 0.01mm Light source laser Wavelength 650nm (visible red light) Light spot divergent, 1x6mm 2 at 45mm Laser warning notice see remarks rror limits (relative to measurement distance) bsolute measurement accuracy 1) 0.5% Repeatability 2) 0.1% b/w detection thresh. (6 90% rem.) 0.5% Timing Measurement time 4 10ms Response time 20ms elay before start-up 300ms lectrical data Operating voltage U 18 30V (incl. residual ripple) Residual ripple 15% of U ias current 50m Switching output PNP transistor, high-active Signal voltage high/low (U -2 V)/ 2V nalogue output voltage 1 10V, R L 2kΩ current 4 20m, R L 500Ω Indicators teach-in on GN teach-in on +U L green continuous light ready flashing fault teaching procedure no voltage L yellow continuous light object inside teach-in measurement distance flashing teaching procedure object outside teach-in measurement distance Mechanical data Housing metal Optics cover glass Weight 70g onnection type M12 connector, 8-pin, turning nvironmental data mbient temp. (operation/storage) -20 +50 /-40 +70 Protective circuit 3) 2, 3 V safety class 4) II, all-insulated Protection class 5) IP 67, IP 69K 6) Laser class 2 (acc. to N 60825-1) Standards applied I 60947-5-2 1) Luminosity coefficient 6% 90%, over the entire temperature range, measurement object 50x50mm² 2) Same object, identical environmental conditions, measurement object 50x50mm² 3) 2=polarity reversal protection, 3=short-circuit protection for all outputs 4) Rating voltage 250V 5) In stop position of the turning connector (turning connector locked) 6) IP 69K test acc. to IN 40050 part 9 simulated, high pressure cleaning conditions without the use of additives, acids and bases are not part of the test F rea not defined Linearity not defined Measurement range Object present No object detected Measurement distance Tables iagrams Remarks Measurement time depends on the reflectivity of the measurement object and on the measurement mode. Teaching procedure: Position measured object at desired measurement distance. onnect teach input to +U for 2s. Reconnect teach input to GN, switching output is programmed. The voltage output of the analogue version is calibrated before delivery. Order guide esignation With M12 connector OSL 8/V4-45-S12 501 01883 onfiguration adaptor UPG 5 500 39627 OSL 8/V4-45-S12-05 0706 11
OSL 8 Optical laser distance sensors imensioned drawing 25 45mm 10-30 V Reflection-independent distance information Highly insensitive to extraneous light igital RS 232 and RS 485 interface Measurement range and mode adjustable Teachable switching output M12 turning connector F Receiver Transmitter Optical axis 90 turning connector L yellow, green Reference edge for the measurement (cover glass) lectrical connection We reserve the right to make changes ods_22e.fm I 60947... I 60947... ccessories: (available separately see page 84) Mounting systems able with M12 connector (K- ) onfiguration software ontrol guard IP 69K IP 67 Leuze electronic GmbH + o. KG Post-box 1111-73277 Owen-Teck Tel. +49 7021 5730 www.leuze.de 12 OSL 8/4-45-S12-05
OSL 8 Specifications Optical data Measurement range 1) 25 45mm Resolution 0.01mm Light source laser Wavelength 650nm (visible red light) Light spot divergent, 1x6mm 2 at 45mm Laser warning notice see remarks rror limits (relative to measurement distance) bsolute measurement accuracy 1) 0.5% Repeatability 2) 0.1% b/w detection thresh. (6 90% rem.) 0.5% Timing Measurement time 4 10ms Response time 20ms elay before start-up 300ms lectrical data Operating voltage U 10 30V (incl. residual ripple) Residual ripple 15% of U ias current 50m Switching output PNP transistor, high-active Signal voltage high/low (U -2 V)/ 2V igital output RS 232 3) 9600 aud RS 485 3) 9600 aud, no termination Transmission protocol 4) 2 byte transmission, continuous data flow Indicators L green continuous light ready flashing fault teaching procedure no voltage L yellow continuous light object inside teach-in measurement distance flashing teaching procedure object outside teach-in measurement distance Mechanical data Housing metal Optics cover glass Weight 70g onnection type M12 connector, 8-pin, turning nvironmental data mbient temp. (operation/storage) -20 +50 /-40 +70 Protective circuit 5) 1, 2, 3 V safety class 6) II, all-insulated Protection class 7) IP 67, IP 69K 8) Laser class 2 (acc. to N 60825-1) Standards applied I 60947-5-2 1) Luminosity coefficient 6% 90%, over the entire temperature range, measurement object 50x50mm² 2) Same object, identical environmental conditions, measurement object 50x50mm² 3) Higher baud rates can be set 4) 2byte transmission protocol 5) 1=transient protection, 2=polarity reversal protection, 3=short-circuit protection for all outputs 6) Rating voltage 250V 7) In stop position of the turning connector (turning connector locked) 8) IP 69K test acc. to IN 40050 part 9 simulated, high pressure cleaning conditions without the use of additives, acids and bases are not part of the test Measurement value Tables iagrams Remarks Parameterisation via P - onnect the device to voltage and simultaneously apply +24V to teach-in (PIN 5) - onnect RS 232 directly to the P - Start OS 96 configuration software, password "OS_96" Measurement time depends on the reflectivity of the measurement object and on the measurement mode. Teaching procedure: Position measured object at desired measurement distance. onnect teach input to +U for 2s. Reconnect teach input to GN, switching output is programmed. Order guide esignation With M12 connector OSL 8/4-45-S12 501 01884 OSL 8/4-45-S12-05 0706 13
OSL 8 Optical laser distance sensors imensioned drawing 20 200mm 18-30 V Reflection-independent distance information Highly insensitive to extraneous light nalogue voltage output 1 10V (can be inverted, teachable) 2 teachable switching outputs (push-pull) M12 turning connector asy alignment through visible red light F G Receiver Transmitter Optical axis 90 turning connector L yellow, green Operational control (rotary switch) Reference edge for the measurement (cover glass) lectrical connection We reserve the right to make changes ods_37e.fm I 60947... I 60947... ccessories: (available separately see page 84) Mounting systems able with M12 connector (K- ) ontrol guard IP 69K IP 67 Leuze electronic GmbH + o. KG Post-box 1111-73277 Owen-Teck Tel. +49 7021 5730 www.leuze.de 14 OSL 8/V 66-200-S12-04
OSL 8 Specifications Optical data Measurement range 1) 20 200mm Resolution 2) 0.1 0.2mm Light source laser Wavelength 630nm (visible red light) Light spot Ø 1mm at 200mm Laser warning notice see remarks rror limits (relative to measurement distance) bsolute measurement accuracy 1) ± 2% up to 200mm Repeatability 3) ± 1% up to 200mm b/w detection thresh. (6 90% rem.) 1.5% Temperature drift 0.2%/ Timing Measurement time 2 7ms Response time 20ms elay before start-up 300ms lectrical data Operating voltage U 18 30V (incl. residual ripple) Residual ripple 15% of U ias current 50m Switching output/function 4) 2 push-pull switching outputs pin 2: Q2, PNP light switching, NPN dark switching pin 4: Q1, PNP light switching, NPN dark switching Signal voltage high/low (U -2 V)/ 2V nalogue output voltage 1 10V, R L 2kΩ Indicators L green continuous light ready flashing (no Teach) fault, teach values were not applied no voltage L yellow continuous light object within teach-in measurement distance (output Q1 5) ) flashing (no Teach) teach values were not applied object outside teach-in measurement distance (output Q1 4) ) Mechanical data Housing metal Optics cover glass Weight 70g onnection type M12 connector, 5-pin, turning nvironmental data mbient temp. (operation/storage) -20 +50 /-40 +70 Protective circuit 6) 2, 3 V safety class 7) II, all-insulated Protection class 8) IP 67, IP 69K 9) Laser class 2 (acc. to N 60825-1) Standards applied I 60947-5-2 1) Luminosity coefficient 6% 90%, at 20, measurement object 20x20mm² 2) Minimum and maximum value depend on measurement distance and configuration of the analogue output 3) Same object, identical environmental conditions, measurement object 20x20mm² 4) The push-pull switching outputs must not be connected in parallel 5) No display for output Q2 6) 2=polarity reversal protection, 3=short-circuit protection for all outputs 7) Rating voltage 250V 8) In stop position of the turning connector (turning connector locked) 9) IP 69K test acc. to IN 40050 part 9 simulated, high pressure cleaning conditions without the use of additives, acids and bases are not part of the test haracteristic curve of analogue output: F rea not defined Linearity not defined Measurement range Object present No object detected Measurement distance Tables iagrams haracteristic curve of switching outputs: Hysteresis Switching point Q1 (teach point) Switching point Q2 (teach point) Measurement distance Remarks Measurement time depends on the reflectivity of the measurement object and on the measurement mode. Order guide esignation Part No. With M12 connector and analogue output OSL 8/V 66-200-S12 501 05761 OSL 8/V 66-200-S12-04 0706 15
OSL 8 T I teach-in with rotary switch 1.Position measurement object at the desired distance (➀). Optical laser distance sensors ➀ 2.Turn rotary switch into the desired position (Low, High, 1, 2) (➁). Wait for optical confirmation by flashing of the Ls. Teach function Rotary switch position L green L yellow 1V analogue output low on flashes 10V analogue output high flashes on switching output Q1 1 flash synchronously switching output Q2 2 flash alternatingly 3.For teaching, position rotary switch onto "Run" (➂). Wait for optical confirmation by end of flashing signal (green L on). ➁ ➂ Reset of the analogue output to factory settings Reset 1V analogue output at 20mm: 1.Position measurement object just below start of measurement range (20mm). 2.Position rotary switch on "Low". Wait for optical confirmation by flashing of the Ls. 3.For teaching, position rotary switch onto "Run". Wait for optical confirmation by end of flashing signal (green L on). Reset 10V analogue output at 200mm: 1.Position measurement object just beyond end of measurement range (200mm). 2.Position rotary switch on "High". Wait for optical confirmation by flashing of the Ls. 3.For teaching, position rotary switch onto "Run". Wait for optical confirmation by end of flashing signal (green L on). rror messages ontinuously flashing Ls in switch position "Run" signal an unsuccessful teach event (sensor not ready): L L rror green yellow on flashes teach 1V analogue output unsuccessful flashes on teach 10V analogue output unsuccessful flash synchronously teach switching output Q1 unsuccessful flash alternatingly teach switching output Q1 unsuccessful Remedy: Repeat teach event or isconnect sensor from voltage to restore the old values. Typical areas of application of optical distance sensors ontinuous distance measurement Positioning tasks Filling level control OSL 8 OSL 8 New stack OSL 8 Positioning Leuze electronic GmbH + o. KG Post-box 1111-73277 Owen-Teck Tel. +49 7021 5730 OSL 8/V 66-200-S12-04 www.leuze.de 16
Installation instructions Leuze electronic OSL 8 Mounting systems are available which have to be ordered separately at Leuze electronic. part from this, the drilled-through holes and threaded holes are suitable for the individual mounting of the OSL 8, depending on the area in which it is used. When mounting, avoid application of excessive force on the housing. Preferred movement of the objects Preferred mounting in connection to objects with structured surface View through a chase If the OSL 8 has to be installed behind a cover, the chase has to have at least the size of the optical glass cover. Otherwise, a correct measurement is not possible or can not be guaranteed. lignment to measurement objects with reflecting surfaces If the measurement object to be detected has a reflecting surface, a measurement may not be possible depending on the angle in which the light is reflected by the measurement object's surface. djust the angle between the sensor and the measurement object such that the sensor can reliably detect the measurement object. Working Safely ttention Laser Radiation! The optical distance sensors OSL 8 operate with a red light laser of class 2 acc. to N 60825-1. If you look into the beam path over a longer time period, the retina of your eye may be damaged! Never look directly into the beam path! o not point the laser beam of the OSL 8 at persons! When mounting and aligning the OSL 8 take care to avoid reflections of the laser beam reflective surfaces! The use of operating and adjusting devices other than those specified in the technical description, carrying out of differing procedures, or improper use of the optical laser distance sensor may lead to dangerous exposure to radiation! The use of optical instruments or devices in combination with the device increases the danger of eye damage! dhere to the applicable legal and local regulations regarding protection from laser beams acc. to N 60825-1 in its latest version. The OSL 8 uses a laser diode with low power in the visible red light range with an emitted wavelength of about 630nm. The glass optics cover is the only opening through which the laser radiation can escape from the device. The housing of the OSL 8 is sealed and has no parts that need to be adjusted or maintained by the user. The device must not be tampered with and must not be changed in any way! The destruction of the seal voids the warranty! Notice! It is important that you attach the sticky labels supplied to the device (notice signs and laser emission symbol)! If the signs would be covered due to the installation situation of the OSL 8, attach them close to the OSL 8 such that reading the notices cannot lead to looking into the laser beam! OSL 8/V 66-200-S12-04 0706 17
OSL 8 Optical laser distance sensors imensioned drawing 20 400mm 18-30 V Reflection-independent distance information Highly insensitive to extraneous light nalogue current and voltage output Measurement range and mode adjustable Teachable switching output M12 turning connector F Receiver Transmitter Optical axis 90 turning connector L yellow, green Reference edge for measurement (cover glass) U L US LIST lectrical connection We reserve the right to make changes ods_12e.fm I 60947... I 60947... ccessories: (available separately see page 84) Mounting systems able with M12 connector (K- ) onfiguration software onfiguration adaptor UPG 5 ontrol guard IP 69K IP 67 Leuze electronic GmbH + o. KG Post-box 1111-73277 Owen-Teck Tel. +49 7021 5730 www.leuze.de 18 OSL 8/V... - 07
OSL 8 Specifications Optical data Measurement range 1) 20 400mm Resolution 0.1mm Light source laser Wavelength 650nm (visible red light) Light spot divergent, 1x6mm 2 at 400mm Laser warning notice see remarks rror limits (relative to measurement distance) bsolute measurement accuracy 1) ± 1% up to 200mm / ± 2% 200 400mm Repeatability 2) ± 0.25% up to 200mm / ± 1% 200 400mm b/w detection thresh. (6 90% rem.) 1% Timing Measurement time 4 10ms Response time 20ms elay before start-up 300ms lectrical data Operating voltage U 18 30V (incl. residual ripple) Residual ripple 15% of U ias current 50m Switching output PNP transistor, high-active Signal voltage high/low (U -2 V)/ 2V nalogue output voltage 1 10V, R L 2kΩ current 4 20m, R L 500Ω Indicators teach-in on GN teach-in on +U L green continuous light ready flashing fault teaching procedure no voltage L yellow continuous light object inside teach-in measurement distance flashing teaching procedure object outside teach-in measurement distance Mechanical data Housing metal Optics cover glass Weight 70g onnection type M12 connector, 8-pin, turning nvironmental data mbient temp. (operation/storage) -20 +50 /-40 +70 Protective circuit 3) 2, 3 V safety class 4) II, all-insulated Protection class 5) IP 67, IP 69K 6) Laser class 2 (acc. to N 60825-1) Standards applied I 60947-5-2 1) Luminosity coefficient 6% 90%, over the entire temperature range, measurement object 50x50mm² 2) Same object, identical environmental conditions, measurement object 50x50mm² 3) 2=polarity reversal protection, 3=short-circuit protection for all outputs 4) Rating voltage 250V 5) In stop position of the turning connector (turning connector locked) 6) IP 69K test acc. to IN 40050 part 9 simulated, high pressure cleaning conditions without the use of additives, acids and bases are not part of the test F rea not defined Linearity not defined Measurement range Object present No object detected Measurement distance Tables iagrams Remarks Measurement time depends on the reflectivity of the measurement object and on the measurement mode. Teaching procedure: Position measured object at desired measurement distance. onnect teach input to +U for 2s. Reconnect teach input to GN, switching output is programmed. The voltage output of the analogue version is calibrated before delivery. Order guide esignation With M12 connector OSL 8/V4-400-S12 500 39614 onfiguration adaptor UPG 5 500 39627 OSL 8/V... - 07 0706 19
OSL 8 Optical laser distance sensors imensioned drawing 20 400mm 10-30 V Reflection-independent distance information Highly insensitive to extraneous light igital RS 232 and RS 485 interface Measurement range and mode adjustable Teachable switching output M12 turning connector F Receiver Transmitter Optical axis 90 turning connector L yellow, green Reference edge for the measurement (cover glass) U L US LIST lectrical connection We reserve the right to make changes ods_15e.fm I 60947... I 60947... ccessories: (available separately see page 84) Mounting systems onfiguration software able with M12 connector (K- ) ontrol guard IP 69K IP 67 Leuze electronic GmbH + o. KG Post-box 1111-73277 Owen-Teck Tel. +49 7021 5730 www.leuze.de 20 OSL 8/... - 07
OSL 8 Specifications Optical data Measurement range 1) 20 400mm Resolution 0.1mm Light source laser Wavelength 650nm (visible red light) Light spot divergent, 1x6mm 2 at 400mm Laser warning notice see remarks rror limits (relative to measurement distance) bsolute measurement accuracy 1) ± 1% up to 200mm / ± 2% 200 400mm Repeatability 2) ± 0.25% up to 200mm / ± 1% 200 400mm b/w detection thresh. (6 90% rem.) 1% Timing Measurement time 4 10ms Response time 20ms elay before start-up 300ms lectrical data Operating voltage U 10 30V (incl. residual ripple) Residual ripple 15% of U ias current 50m Switching output PNP transistor, high-active Signal voltage high/low (U -2 V)/ 2V igital output RS 232 3) 9600 aud RS 485 3) 9600 aud, no termination Transmission protocol 4) 2 byte transmission, continuous data flow Indicators L green continuous light ready flashing fault teaching procedure no voltage L yellow continuous light object inside teach-in measurement distance flashing teaching procedure object outside teach-in measurement distance Mechanical data Housing metal Optics cover glass Weight 70g onnection type M12 connector, 8-pin, turning nvironmental data mbient temp. (operation/storage) -20 +50 /-40 +70 Protective circuit 5) 1, 2, 3 V safety class 6) II, all-insulated Protection class 7) IP 67, IP 69K 8) Laser class 2 (acc. to N 60825-1) Standards applied I 60947-5-2 1) Luminosity coefficient 6% 90%, over the entire temperature range, measurement object 50x50mm² 2) Same object, identical environmental conditions, measurement object 50x50mm² 3) Higher baud rates can be set 4) 2byte transmission protocol 5) 1=transient protection, 2=polarity reversal protection, 3=short-circuit protection for all outputs 6) Rating voltage 250V 7) In stop position of the turning connector (turning connector locked) 8) IP 69K test acc. to IN 40050 part 9 simulated, high pressure cleaning conditions without the use of additives, acids and bases are not part of the test Measurement value Tables iagrams Remarks Parameterisation via P: - onnect the device to voltage and simultaneously apply +24V to teach-in (PIN 5) - onnect RS 232 directly to the P - Start OS 96 configuration software, password "OS_96" Measurement time depends on the reflectivity of the measurement object and on the measurement mode. Teaching procedure: Position measured object at desired measurement distance. onnect teach input to +U for 2s. Reconnect teach input to GN, switching output is programmed. Order guide esignation With M12 connector OSL 8/4-400-S12 500 39615 OSL 8/... - 07 0706 21
OSL 8 Optical laser distance sensors imensioned drawing 20 500mm 18-30 V Reflection-independent distance information Highly insensitive to extraneous light nalogue voltage output 1 10V (can be inverted, teachable) 2 teachable switching outputs (push-pull) M12 turning connector asy alignment through visible red light F G Receiver Transmitter Optical axis 90 turning connector L yellow, green Operational control (rotary switch) Reference edge for the measurement (cover glass) lectrical connection We reserve the right to make changes ods_23e.fm I 60947... I 60947... ccessories: (available separately see page 84) Mounting systems able with M12 connector (K- ) ontrol guard IP 69K IP 67 Leuze electronic GmbH + o. KG Post-box 1111-73277 Owen-Teck Tel. +49 7021 5730 www.leuze.de 22 OSL 8/V 66-500-S12-06
OSL 8 Specifications Optical data Measurement range 1) 20 500mm Resolution 2) 0.1 0.5mm Light source laser Wavelength 630nm (visible red light) Light spot 1x6mm 2 at 500mm Laser warning notice see remarks rror limits (relative to measurement distance) bsolute measurement accuracy 1) ± 2% up to 200mm / ± 4% 200 500mm Repeatability 3) ± 1% up to 200mm / ± 3% 200 500mm b/w detection thresh. (6 90% rem.) 1.5% Temperature drift 0.2%/ Timing Measurement time 2 7ms Response time 20ms elay before start-up 300ms lectrical data Operating voltage U 18 30V (incl. residual ripple) Residual ripple 15% of U ias current 50m Switching output/function 4) 2 push-pull switching outputs pin 2: Q2, PNP light switching, NPN dark switching pin 4: Q1, PNP light switching, NPN dark switching Signal voltage high/low (U -2 V)/ 2V nalogue output voltage 1 10V, R L 2kΩ Indicators L green continuous light ready flashing (no Teach) fault, teach values were not applied no voltage L yellow continuous light object within teach-in measurement distance (output Q1 5) ) flashing (no Teach) teach values were not applied object outside teach-in measurement distance (output Q1 4) ) Mechanical data Housing metal Optics cover glass Weight 70g onnection type M12 connector, 5-pin, turning nvironmental data mbient temp. (operation/storage) -20 +50 /-40 +70 Protective circuit 6) 2, 3 V safety class 7) II, all-insulated Protection class 8) IP 67, IP 69K 9) Laser class 2 (acc. to N 60825-1) Standards applied I 60947-5-2 1) Luminosity coefficient 6% 90%, at 20, measurement object 50x50mm² 2) Minimum and maximum value depend on measurement distance and configuration of the analogue output 3) Same object, identical environmental conditions, measurement object 50x50mm² 4) The push-pull switching outputs must not be connected in parallel 5) No display for output Q2 6) 2=polarity reversal protection, 3=short-circuit protection for all outputs 7) Rating voltage 250V 8) In stop position of the turning connector (turning connector locked) 9) IP 69K test acc. to IN 40050 part 9 simulated, high pressure cleaning conditions without the use of additives, acids and bases are not part of the test haracteristic curve of analogue output: F rea not defined Linearity not defined Measurement range Object present No object detected Measurement distance Tables iagrams haracteristic curve of switching outputs: Hysteresis Switching point Q1 (teach point) Switching point Q2 (teach point) Measurement distance Remarks Measurement time depends on the reflectivity of the measurement object and on the measurement mode. Order guide esignation Part No. With M12 connector and analogue output OSL 8/V 66-500-S12 501 01879 OSL 8/V 66-500-S12-06 0706 23
OSL 8 T I teach-in with rotary switch 1.Position measurement object at the desired distance (➀). Optical laser distance sensors ➀ 2.Turn rotary switch into the desired position (Low, High, 1, 2) (➁). Wait for optical confirmation by flashing of the Ls. Teach function Rotary switch position L green L yellow 1V analogue output low on flashes 10V analogue output high flashes on switching output Q1 1 flash synchronously switching output Q2 2 flash alternatingly 3.For teaching, position rotary switch onto "Run" (➂). Wait for optical confirmation by end of flashing signal (green L on). ➁ ➂ Reset of the analogue output to factory settings Reset 1V analogue output at 20mm: 1.Position measurement object just below start of measurement range (20mm). 2.Position rotary switch on "Low". Wait for optical confirmation by flashing of the Ls. 3.For teaching, position rotary switch onto "Run". Wait for optical confirmation by end of flashing signal (green L on). Reset 10V analogue output at 500mm: 1.Position measurement object just beyond end of measurement range (500mm). 2.Position rotary switch on "High". Wait for optical confirmation by flashing of the Ls. 3.For teaching, position rotary switch onto "Run". Wait for optical confirmation by end of flashing signal (green L on). rror messages ontinuously flashing Ls in switch position "Run" signal an unsuccessful teach event (sensor not ready): L L rror green yellow on flashes teach 1V analogue output unsuccessful flashes on teach 10V analogue output unsuccessful flash synchronously teach switching output Q1 unsuccessful flash alternatingly teach switching output Q1 unsuccessful Remedy: Repeat teach event or isconnect sensor from voltage to restore the old values. Typical areas of application of optical distance sensors ontinuous distance measurement Positioning tasks Filling level control OSL 8 OSL 8 New stack OSL 8 Positioning Leuze electronic GmbH + o. KG Post-box 1111-73277 Owen-Teck Tel. +49 7021 5730 OSL 8/V 66-500-S12-06 www.leuze.de 24
Installation instructions Leuze electronic OSL 8 Mounting systems are available which have to be ordered separately at Leuze electronic. part from this, the drilled-through holes and threaded holes are suitable for the individual mounting of the OSL 8, depending on the area in which it is used. When mounting, avoid application of excessive force on the housing. Preferred movement of the objects Preferred mounting in connection to objects with structured surface View through a chase If the OSL 8 has to be installed behind a cover, the chase has to have at least the size of the optical glass cover. Otherwise, a correct measurement is not possible or can not be guaranteed. lignment to measurement objects with reflecting surfaces If the measurement object to be detected has a reflecting surface, a measurement may not be possible depending on the angle in which the light is reflected by the measurement object's surface. djust the angle between the sensor and the measurement object such that the sensor can reliably detect the measurement object. Working Safely ttention Laser Radiation! The optical distance sensors OSL 8 operate with a red light laser of class 2 acc. to N 60825-1. If you look into the beam path over a longer time period, the retina of your eye may be damaged! Never look directly into the beam path! o not point the laser beam of the OSL 8 at persons! When mounting and aligning the OSL 8 take care to avoid reflections of the laser beam reflective surfaces! The use of operating and adjusting devices other than those specified in the technical description, carrying out of differing procedures, or improper use of the optical laser distance sensor may lead to dangerous exposure to radiation! The use of optical instruments or devices in combination with the device increases the danger of eye damage! dhere to the applicable legal and local regulations regarding protection from laser beams acc. to N 60825-1 in its latest version. The OSL 8 uses a laser diode with low power in the visible red light range with an emitted wavelength of about 630nm. The glass optics cover is the only opening through which the laser radiation can escape from the device. The housing of the OSL 8 is sealed and has no parts that need to be adjusted or maintained by the user. The device must not be tampered with and must not be changed in any way! The destruction of the seal voids the warranty! Notice! It is important that you attach the sticky labels supplied to the device (notice signs and laser emission symbol)! If the signs would be covered due to the installation situation of the OSL 8, attach them close to the OSL 8 such that reading the notices cannot lead to looking into the laser beam! OSL 8/V 66-500-S12-06 0706 25
OSL 8 Optical laser distance sensors imensioned drawing 20 500mm 10-30 V Reflection-independent distance information Highly insensitive to extraneous light 2 teachable switching outputs (push-pull) M12 turning connector asy alignment through visible red light F G Receiver Transmitter Optical axis 90 turning connector L yellow, green Operational control (rotary switch) Reference edge for the measurement (cover glass) lectrical connection We reserve the right to make changes ods_31e.fm I 60947... I 60947... ccessories: (available separately see page 84) Mounting systems able with M12 connector (K- ) ontrol guard IP 69K IP 67 Leuze electronic GmbH + o. KG Post-box 1111-73277 Owen-Teck Tel. +49 7021 5730 www.leuze.de 26 OSL 8/66-500-S12-04
OSL 8 Specifications Optical data Measurement range 1) 20 500mm Resolution 2) 0.1 0.5mm Hysteresis 2) 0.6 32mm Light source laser Wavelength 630nm (visible red light) Light spot 1x6mm 2 at 500mm Laser warning notice see remarks rror limits (relative to measurement distance) bsolute measurement accuracy 1) ± 2% up to 200mm / ± 4% 200 500mm Repeatability 3) ± 1% up to 200mm / ± 3% 200 500mm b/w detection thresh. (6 90% rem.) 1.5% Temperature drift 0.2%/ Timing Measurement time 2 7ms Response time 20ms elay before start-up 300ms lectrical data Operating voltage U 10 30V (incl. residual ripple) Residual ripple 15% of U ias current 50m Switching output/function 4) 2 push-pull switching outputs pin 2: Q2, PNP light switching, NPN dark switching pin 4: Q1, PNP light switching, NPN dark switching Signal voltage high/low (U -2 V)/ 2V Indicators L green continuous light ready flashing (no Teach) fault, teach values were not applied no voltage L yellow continuous light object within teach-in measurement distance (output Q1 5) ) flashing (no Teach) teach values were not applied object outside teach-in measurement distance (output Q1 4) ) Mechanical data Housing metal Optics cover glass Weight 70g onnection type M12 connector, 5-pin, turning nvironmental data mbient temp. (operation/storage) -20 +50 /-40 +70 Protective circuit 6) 2, 3 V safety class 7) II, all-insulated Protection class 8) IP 67, IP 69K 9) Laser class 2 (acc. to N 60825-1) Standards applied I 60947-5-2 1) Luminosity coefficient 6% 90%, at 20, measurement object 50x50mm² 2) Minimum and maximum value depend on measurement distance 3) Same object, identical environmental conditions, measurement object 50x50mm² 4) The push-pull switching outputs must not be connected in parallel 5) No display for output Q2 6) 2=polarity reversal protection, 3=short-circuit protection for all outputs 7) Rating voltage 250V 8) In stop position of the turning connector (turning connector locked) 9) IP 69K test acc. to IN 40050 part 9 simulated, high pressure cleaning conditions without the use of additives, acids and bases are not part of the test haracteristic curve of switching outputs: Tables iagrams Remarks Measurement time depends on the reflectivity of the measurement object and on the measurement mode. Hysteresis Switching point Q1 (teach point) Switching point Q2 (teach point) Measurement distance Order guide esignation Part No. With M12 connector OSL 8/66-500-S12 501 01880 OSL 8/66-500-S12-04 0706 27
OSL 8 T I teach-in with rotary switch 1.Position measurement object at the desired distance (➀). Optical laser distance sensors ➀ 2.Turn rotary switch into the desired position (Low, High, 1, 2) (➁). Wait for optical confirmation by flashing of the Ls. Teach function Rotary switch position L green L yellow switching output Q1 1 flash synchronously switching output Q2 2 flash alternatingly 3.For teaching, position rotary switch onto "Run" (➂). Wait for optical confirmation by end of flashing signal (green L on). ➁ ➂ T I teach-in via input 1.Position measurement object at the desired distance. 2.The respective teach function is activated by applying +U to teach input (pin 5). The teach event is signalled by flashing of the Ls. Teach function uration of the teach signal L green L yellow switching output Q1 2 4s flash synchronously switching output Q2 4 6s flash alternatingly 3.To finish the teach event, disconnect the teach input from +U or switch it to 0V after the desired time. 4. successful teach event is signalled by the end of the flashing (green L on) rror messages ontinuously flashing Ls signal an unsuccessful teach event (sensor not ready): L L green yellow flash synchronously flash alternatingly rror teach switching output Q1 unsuccessful teach switching output Q1 unsuccessful Remedy: Repeat teach event or isconnect sensor from voltage to restore the old values. Typical areas of application of optical distance sensors ontinuous distance measurement Positioning tasks Filling level control OSL 8 OSL 8 New stack OSL 8 Positioning Leuze electronic GmbH + o. KG Post-box 1111-73277 Owen-Teck Tel. +49 7021 5730 OSL 8/66-500-S12-04 www.leuze.de 28
Installation instructions Leuze electronic OSL 8 Mounting systems are available which have to be ordered separately at Leuze electronic. part from this, the drilled-through holes and threaded holes are suitable for the individual mounting of the OSL 8, depending on the area in which it is used. When mounting, avoid application of excessive force on the housing. Preferred movement of the objects Preferred mounting in connection to objects with structured surface View through a chase If the OSL 8 has to be installed behind a cover, the chase has to have at least the size of the optical glass cover. Otherwise, a correct measurement is not possible or can not be guaranteed. lignment to measurement objects with reflecting surfaces If the measurement object to be detected has a reflecting surface, a measurement may not be possible depending on the angle in which the light is reflected by the measurement object's surface. djust the angle between the sensor and the measurement object such that the sensor can reliably detect the measurement object. Working Safely ttention Laser Radiation! The optical distance sensors OSL 8 operate with a red light laser of class 2 acc. to N 60825-1. If you look into the beam path over a longer time period, the retina of your eye may be damaged! Never look directly into the beam path! o not point the laser beam of the OSL 8 at persons! When mounting and aligning the OSL 8 take care to avoid reflections of the laser beam reflective surfaces! The use of operating and adjusting devices other than those specified in the technical description, carrying out of differing procedures, or improper use of the optical laser distance sensor may lead to dangerous exposure to radiation! The use of optical instruments or devices in combination with the device increases the danger of eye damage! dhere to the applicable legal and local regulations regarding protection from laser beams acc. to N 60825-1 in its latest version. The OSL 8 uses a laser diode with low power in the visible red light range with an emitted wavelength of about 630nm. The glass optics cover is the only opening through which the laser radiation can escape from the device. The housing of the OSL 8 is sealed and has no parts that need to be adjusted or maintained by the user. The device must not be tampered with and must not be changed in any way! The destruction of the seal voids the warranty! Notice! It is important that you attach the sticky labels supplied to the device (notice signs and laser emission symbol)! If the signs would be covered due to the installation situation of the OSL 8, attach them close to the OSL 8 such that reading the notices cannot lead to looking into the laser beam! OSL 8/66-500-S12-04 0706 29
OS 96 Optical distance sensors imensioned drawing 100 600mm 18-30 V Reflection-independent distance information Highly insensitive to extraneous light nalogue current or voltage output Measurement range and mode adjustable Teachable switching output F G H I K L M Indicator diode green Indicator diode yellow Transmitter Receiver Optical axis evice plug M12x1 Screwed cable gland PG11 for Ø5 10mm ountersinking for SK nut M5, 4.2mm deep Parameter plug onnection terminals able entry Reference edge for the measurement (cover glass) U L US LIST lectrical connection We reserve the right to make changes ods_06e.fm I 60947... I 60947... ccessories: (available separately see page 88) IP 69K IP 67 Mounting systems able with M12 connector (K- ) onfiguration software onfiguration cable K-OS96-1500 Leuze electronic GmbH + o. KG Post-box 1111-73277 Owen-Teck Tel. +49 7021 5730 www.leuze.de 30 OS 96M/V - 07
OS 96 Specifications Optical data Measurement range 1) 100 600mm Resolution 2) 0.1 0.5mm Light source L Wavelength 880nm (infrared) Light spot Ø approx. 10mm (over entire measurement range) rror limits (relative to measurement distance) bsolute measurement accuracy 1) ±2% Repeatability 3) ±0.5% b/w detect. thresholds (6 90% rem.) 1% Temperature drift 0.3%/ Timing Measurement time 10 50ms Response time 150ms elay before start-up 300ms lectrical data Operating voltage U 18 30V (incl. residual ripple) Residual ripple 15% of U ias current 150m Switching output PNP transistor, high-active Signal voltage high/low (U -2V)/ 2V nalogue output voltage 1 10V, R L 2kΩ current 4 20m, R L 500Ω Indicators teach-in on GN teach-in on +U L green continuous light ready flashing fault teaching procedure no voltage L yellow continuous light object inside teach-in measurement distance flashing teaching procedure object outside teach-in measurement distance Mechanical data Metal housing Housing diecast zinc Optics cover glass Weight 380g onnection type terminals or M12 connectors nvironmental data mbient temp. (operation/storage) -20 +50 / -30 +70 Protective circuit 4) 1, 2, 3 V safety class 5) II, all-insulated Protection class IP 67, IP 69K 6) L class 1 (acc. to N 60825-1) Standards applied I 60947-5-2 1) Luminosity coefficient 6% 90%, at 20, measurement object 50x50mm² 2) Minimum and maximum value depend on measurement distance 3) Same object, identical environmental conditions, measurement object 50x50mm² 4) 1=transient protection, 2=polarity reversal protection, 3=short-circuit protection for all outputs 5) Rating voltage 250V 6) IP 69K test acc. to IN 40050 part 9 simulated, high pressure cleaning conditions without the use of additives, acids and bases are not part of the test Tables iagrams Order guide rea not defined Linearity not defined Measurement range Object present No object detected F Measurement distance esignation Part No. UL Remarks Measurement time depends on the reflectivity of the measurement object and on the measurement mode. Teaching procedure: Position measured object at desired measurement distance. onnect teach input to +U for 2s. Reconnect teach input to GN, switching output is programmed. With terminals urrent output OS 96M/V-5000-600-220 500 81127 Voltage output OS 96M/V-5010-600-221 500 81128 With M12 connector urrent output OS 96M/V-5000-600-420 500 81129 Voltage output OS 96M/V-5010-600-421 500 81130 OS 96M/V - 07 0706 31
OS 96 Optical distance sensors imensioned drawing 100 600mm 10-30 V Reflection-independent distance information Highly insensitive to extraneous light RS 232 or RS 485 interface Measurement range and mode adjustable Switching output (teachable with RS 232, adjustable with RS 485) F G H I K L M Indicator diode green Indicator diode yellow Transmitter Receiver Optical axis evice plug M12x1 Screwed cable gland PG11 for Ø5 10mm ountersinking for SK nut M5, 4.2mm deep Parameter plug onnection terminals able entry Reference edge for the measurement (cover glass) U L US LIST lectrical connection We reserve the right to make changes ods_02e.fm I 60947... I 60947... ccessories: IP 69K IP 67 (available separately see page 88) Mounting systems able with M12 connector (K- ) onfiguration software onfiguration cable K-OS96-1500 Leuze electronic GmbH + o. KG Post-box 1111-73277 Owen-Teck Tel. +49 7021 5730 www.leuze.de 32 OS 96M/ - 07
OS 96 Specifications Optical data Measurement range 1) 100 600mm Resolution 2) 0.1 0.5mm Light source L Wavelength 880nm (infrared) Light spot Ø approx. 10mm (over entire measurement range) rror limits (relative to measurement distance) bsolute measurement accuracy 1) ±2% Repeatability 3) ±0.5% b/w detection thresholds (6%/90%) 1% Temperature drift 0.3%/ Timing Measurement time 10 50ms Response time 150ms elay before start-up 300ms lectrical data Operating voltage U 10 30V (incl. residual ripple) Residual ripple 15% of U ias current 150m Switching output PNP transistor, high-active Signal voltage high/low (U -2V)/ 2V igital output RS 232 4) 9600 aud RS 485 3) 9600 aud, no termination Transmission protocol 5) 2 byte transmission, continuous data flow Indicators teach-in on GN teach-in on +U L green continuous light ready flashing fault teaching procedure no voltage L yellow continuous light objects inside teach-in measurement distance flashing teaching procedure object outside teach-in measurement distance Mechanical data Metal housing Housing diecast zinc Optics cover glass Weight 380g onnection type terminals or M12 connectors nvironmental data mbient temp. (operation/storage) -20 +50 / -30 +70 Protective circuit 6) 1, 2, 3 V safety class 7) II, all-insulated Protection class IP 67, IP 69K 8) L class 1 (acc. to N 60825-1) Standards applied I 60947-5-2 1) Luminosity coefficient 6% 90%, at 20, measurement object 50x50mm² 2) Minimum and maximum value depend on measurement distance 3) Same object, identical environmental conditions, measurement object 50x50mm² 4) Higher baud rates can be set 5) 2byte transmission protocol 6) 1=transient protection, 2=polarity reversal protection, 3=short-circuit protection for all outputs 7) Rating voltage 250V 8) IP 69K test acc. to IN 40050 part 9 simulated, high pressure cleaning conditions without the use of additives, acids and bases are not part of the test Measurement value Order guide esignation Part No. With terminals RS 232 OS 96M/-5020-600-222 500 81131 RS 485 OS 96M/-5030-600-223 500 81132 With M12 connector RS 232 OS 96M/-5020-600-422 500 81133 RS 485 OS 96M/-5030-600-423 500 81134 Tables iagrams Remarks Measurement time depends on the reflectivity of the measurement object and on the measurement mode. Teaching procedure: Position measured object at desired measurement distance. onnect teach input to +U for 2s. Reconnect teach input to GN, switching output is programmed. OS 96M/ - 07 0706 33
OS 96 Optical distance sensors imensioned drawing 100 600mm 10-30 V Reflection-independent distance information Highly insensitive to extraneous light Two teachable switching outputs Measurement range and mode adjustable F G H I K L M Indicator diode green Indicator diode yellow Transmitter Receiver Optical axis evice plug M12x1 Screwed cable gland PG11 for Ø5 10mm ountersinking for SK nut M5, 4.2mm deep Parameter plug onnection terminals able entry Reference edge for the measurement (cover glass) lectrical connection We reserve the right to make changes ods_04e.fm I 60947... I 60947... ccessories: (available separately see page 88) IP 69K IP 67 Mounting systems able with M12 connector (K- ) onfiguration software onfiguration cable K-OS96-1500 Leuze electronic GmbH + o. KG Post-box 1111-73277 Owen-Teck Tel. +49 7021 5730 www.leuze.de 34 OS 96M/S - 07
OS 96 Specifications Optical data Measurement range 1) 100 600mm Resolution 2) 0.1 0.5mm Light source L Wavelength 880nm (infrared) Light spot Ø approx. 10mm (over entire measurement range) rror limits (relative to measurement distance) bsolute measurement accuracy 1) ±2% Repeatability 3) ±0.5% b/w detection thresholds (6%/90%) 1% Temperature drift 0.3%/ Timing Measurement time 10 50ms Response time 100ms elay before start-up 300ms lectrical data Operating voltage U 10 30V (incl. residual ripple) Residual ripple 15% of U ias current 150m Switching outputs 2 PNP switching outputs, high-active Signal voltage high/low (U -2V)/ 2V Output current max. 100m per transistor output Indicators teach-in on GN teach-in on +U L green continuous light ready flashing fault teaching procedure no voltage L yellow continuous light object inside measurement range flashing object outside teaching procedure measurement range no object detected Mechanical data Metal housing Housing diecast zinc Optics cover glass Weight 380g onnection type terminals or M12 connectors nvironmental data mbient temp. (operation/storage) -20 +50 / -30 +70 Protective circuit 4) 1, 2, 3 V safety class 5) II, all-insulated Protection class IP 67, IP 69K 6) L class 1 (acc. to N 60825-1) Standards applied I 60947-5-2 1) Luminosity coefficient 6% 90%, at 20, measurement object 50x50mm² 2) Minimum and maximum value depend on measurement distance 3) Same object, identical environmental conditions, measurement object 50x50mm² 4) 1=transient protection, 2=polarity reversal protection, 3=short-circuit protection for all outputs 5) Rating voltage 250V 6) IP 69K test acc. to IN 40050 part 9 simulated, high pressure cleaning conditions without the use of additives, acids and bases are not part of the test Switching output (example) Order guide esignation Hysteresis Switching point Q1 (teach point) Switching point Q2 (teach point) Measurement distance Part No. With terminals 2 PNP switching outputs OS 96M/S-5040-600-224 500 81135 With M12 connector 2 PNP switching outputs OS 96M/S-5040-600-424 500 81137 Tables iagrams Remarks Measurement time depends on the reflectivity of the measurement object and on the measurement mode. Teaching procedure: Position measured object at 1st desired measurement distance. onnect teach input to +U for 2s. oth Ls are flashing simultaneously. Reconnect teach input to GN, 1st switching output is programmed. Position measured object at 2nd desired measuring distance. onnect teach input to +U for 2s. oth Ls are flashing alternatingly. Reconnect teach input to GN, 2nd switching output is programmed. The procedure can be repeated as desired, leave teach input connected to GN in idle mode. OS 96M/S - 07 0706 35
OS 96 Optical distance sensors imensioned drawing 100 600mm 18-30 V Reflection-independent distance information Highly insensitive to extraneous light nalogue current output Measurement range and mode adjustable Teachable switching output asy alignment through visible red light F G H I Indicator diode green Indicator diode yellow Transmitter Receiver Optical axis evice plug M12x1 ountersinking for SK nut M5, 4.2mm deep Parameter plug Reference edge for the measurement (cover glass) U L US LIST lectrical connection We reserve the right to make changes ods_28e.fm I 60947... I 60947... ccessories: (available separately see page 88) IP 69K IP 67 Mounting systems able with M12 connector (K- ) onfiguration software onfiguration cable K-OS96-1500 Leuze electronic GmbH + o. KG Post-box 1111-73277 Owen-Teck Tel. +49 7021 5730 www.leuze.de 36 OS 96M/V-5400-420 - 04
OS 96 Specifications Optical data Measurement range 1) 100 600mm Resolution 2) 0.1 0.5mm Light source L Wavelength 635nm (visible red light) Light spot Ø approx. 10mm (over entire measurement range) rror limits (relative to measurement distance) bsolute measurement accuracy 1) ±2% Repeatability 3) ±0.5% b/w detect. thresholds (6 90% rem.) 1% Temperature drift 0.3%/ Timing Measurement time 10 50ms Response time 150ms elay before start-up 300ms lectrical data Operating voltage U 18 30V (incl. residual ripple) Residual ripple 15% of U ias current 150m Switching output PNP transistor, high-active Signal voltage high/low (U -2 V)/ 2V nalogue output current 4 20m, R L 500Ω Indicators teach-in on GN teach-in on +U L green continuous light ready flashing fault teaching procedure no voltage L yellow continuous light object inside teach-in measurement distance flashing teaching procedure object outside teach-in measurement distance Mechanical data Metal housing Housing diecast zinc Optics cover glass Weight 380g onnection type M12 connector nvironmental data mbient temp. (operation/storage) -20 +50 / -30 +70 Protective circuit 4) 1, 2, 3 V safety class 5) II, all-insulated Protection class IP 67, IP 69K 6) L class 1 (acc. to N 60825-1) Standards applied I 60947-5-2 1) Luminosity coefficient 6% 90%, at 20, measurement object 50x50mm² 2) Minimum and maximum value depend on measurement distance and configuration of the analogue output 3) Same object, identical environmental conditions, measurement object 50x50mm² 4) 1=transient protection, 2=polarity reversal protection, 3=short-circuit protection for all outputs 5) Rating voltage 250V 6) IP 69K test acc. to IN 40050 part 9 simulated, high pressure cleaning conditions without the use of additives, acids and bases are not part of the test Order guide F esignation rea not defined Linearity not defined Measurement range Object present No object detected Measurement distance Part No. Tables iagrams Remarks Measurement time depends on the reflectivity of the measurement object and on the measurement mode. Teaching procedure: Position measured object at desired measurement distance. onnect teach input to +U for 2s. Reconnect teach input to GN, switching output is programmed. With M12 connector urrent output OS 96M/V-5400-420 500 32024 OS 96M/V-5400-420 - 04 0706 37
OS 96 Optical laser distance sensors imensioned drawing 120 1400mm 18-30 V Reflection-independent distance information Highly insensitive to extraneous light nalogue current output Measurement range and mode adjustable 2 PNP or NPN warning outputs (switching points depend on the measurement range configured) F G H I Indicator diode green Indicator diode yellow Transmitter Receiver Optical axis evice plug M12x1 ountersinking for SK nut M5, 4.2mm deep Parameter plug Reference edge for the measurement (cover glass) lectrical connection We reserve the right to make changes ods_27e.fm I 60947... I 60947... ccessories: IP 69K IP 67 (available separately see page 88) Mounting systems able with M12 connector (K- ) onfiguration software onfiguration cable K-OS96-1500 Leuze electronic GmbH + o. KG Post-box 1111-73277 Owen-Teck Tel. +49 7021 5730 www.leuze.de 38 OS 96M/V-5290-426 - 04 OS 96M/V-5310-426 - 04
OS 96 Specifications Optical data Measurement range 1) 120 1400mm Resolution 2) 0.1 1mm Light source L Wavelength 880nm (infrared) Light spot Ø approx. 10mm (over entire measurement range) rror limits (relative to measurement distance) bsolute measurement accuracy 1) ± 2% up to 600mm / ± 3% from 600mm to 1400mm Repeatability 3) ± 0.5% up to 600mm/± 1% from 600mm to 1400mm b/w detect. thresholds (6 90% rem.) 1% up to 600mm/ 2% from 600mm to 1400mm Temperature drift 0.3%/ Timing Measurement time 10 50ms Response time 150ms elay before start-up 300ms lectrical data Operating voltage U 18 30V (incl. residual ripple) Residual ripple 15% of U ias current 150m Switching outputs 2x PNP transistor, HIGH active, or 2x NPN transistor, LOW active Signal voltage high/low (U -2 V)/ 2V nalogue output current 4 20m, R L 500Ω Indicators L green continuous light ready flashing fault no voltage L yellow continuous light object within measurement range flashing object out of measurement range no object detected Mechanical data Metal housing Housing diecast zinc Optics cover glass Weight 380g onnection type M12 connector nvironmental data mbient temp. (operation/storage) -20 +50 / -30 +70 Protective circuit 4) 1, 2, 3 V safety class 5) II, all-insulated Protection class IP 67, IP 69K 6) L class 1 (acc. to N 60825-1) Standards applied I 60947-5-2 1) Luminosity coefficient 6% 90%, over the entire temperature range, measurement object 50x50mm² 2) Minimum and maximum value depend on measurement distance and configuration of the analogue output 3) Same object, identical environmental conditions, measurement object 50x50mm² 4) 1=transient protection, 2=polarity reversal protection, 3=short-circuit protection for all outputs 5) Rating voltage 250V 6) IP 69K test acc. to IN 40050 part 9 simulated, high pressure cleaning conditions without the use of additives, acids and bases are not part of the test Order guide F esignation rea not defined Linearity not defined Measurement range Object present No object detected Measurement distance Part No. With M12 connector urrent output, 2 PNP warning outputs OS 96M/V-5290-426 500 32318 urrent output, 2 PNP warning outputs OS 96M/V-5310-426 500 32840 Tables iagrams Remarks Measurement time depends on the reflectivity of the measurement object and on the measurement mode. oding of the warning outputs: Warning output Meaning 1 2 0 0 0 1 1 0 istance measurement is impossible Object below measurement range (short range) Object beyond the measurement range (distant range) 1 1 Optimum function OS 96M/V-5290-426 - 04 0706 OS 96M/V-5310-426 - 04 39
OS 96 Optical laser distance sensors imensioned drawing 200 1200mm 18-30 V Reflection-independent distance information Highly insensitive to extraneous light nalogue voltage output Measurement range and mode adjustable Teachable switching output F G H I Indicator diode green Indicator diode yellow Transmitter Receiver Optical axis evice plug M12x1 ountersinking for SK nut M5, 4.2mm deep Parameter plug Reference edge for the measurement (cover glass) U L US LIST lectrical connection We reserve the right to make changes ods_17e.fm I 60947... I 60947... ccessories: (available separately see page 88) IP 69K IP 67 Mounting systems able with M12 connector (K- ) onfiguration software onfiguration cable K-OS96-1500 Leuze electronic GmbH + o. KG Post-box 1111-73277 Owen-Teck Tel. +49 7021 5730 www.leuze.de 40 OS 96M/V-5420-421 Laser - 03
OS 96 Specifications Optical data Measurement range 1) 200 1200mm Resolution 2) 0.1 1mm Light source laser Wavelength 660nm (visible red light) Light spot divergent, 3x8mm² at 1200mm Laser warning notice see remarks rror limits (relative to measurement distance) bsolute measurement accuracy 1) ±2% Repeatability 3) ±0.5% b/w detect. thresholds (6 90% rem.) 1% Timing Measurement time 10 100ms Response time 300ms elay before start-up 300ms lectrical data Operating voltage U 18 30V (incl. residual ripple) Residual ripple 15% of U ias current 150m Switching output PNP transistor, high-active Signal voltage high/low (U -2 V)/ 2V nalogue output voltage 1 10V, R L 2kΩ Indicators teach-in on GN teach-in on +U L green continuous light ready flashing fault teaching procedure no voltage L yellow continuous light object inside teach-in measurement distance flashing teaching procedure object outside teach-in measurement distance Mechanical data Metal housing Housing diecast zinc Optics cover glass Weight 380g onnection type M12 connector nvironmental data mbient temp. (operation/storage) -20 +50 / -30 +70 Protective circuit 4) 1, 2, 3 V safety class 5) II, all-insulated Protection class IP 67, IP 69K 6) Laser class 2 (acc. to N 60825-1) Standards applied I 60947-5-2 1) Luminosity coefficient 6% 90%, over the entire temperature range, measurement object 50x50mm² 2) Minimum and maximum value depend on measurement distance and configuration of the analogue output 3) Same object, identical environmental conditions, measurement object 50x50mm² 4) 1=transient protection, 2=polarity reversal protection, 3=short-circuit protection for all outputs 5) Rating voltage 250V 6) IP 69K test acc. to IN 40050 part 9 simulated, high pressure cleaning conditions without the use of additives, acids and bases are not part of the test Order guide F esignation rea not defined Linearity not defined Measurement range Object present No object detected Measurement distance Part No. Tables iagrams Remarks Measurement time depends on the reflectivity of the measurement object and on the measurement mode. Teaching procedure: Position measured object at desired measurement distance. onnect teach input to +U for 2s. Reconnect teach input to GN, switching output is programmed. With M12 connector Voltage output OS 96M/V-5420-421 500 35394 OS 96M/V-5420-421 Laser - 03 0706 41
OS 96 Optical laser distance sensors imensioned drawing 60 2000mm 18-30 V Reflection-independent distance information Highly insensitive to extraneous light nalogue current and voltage output Measurement range and mode adjustable Teachable switching output F G H I Indicator diode green Indicator diode yellow Transmitter Receiver Optical axis evice plug M12x1 ountersinking for SK nut M5, 4.2mm deep Parameter plug Reference edge for the measurement (cover glass) U L US LIST lectrical connection We reserve the right to make changes ods_18e.fm I 60947... I 60947... ccessories: (available separately see page 88) IP 69K IP 67 Mounting systems able with M12 connector (K- ) onfiguration software onfiguration cable K-OS96-1500 Leuze electronic GmbH + o. KG Post-box 1111-73277 Owen-Teck Tel. +49 7021 5730 www.leuze.de 42 OS 96M/V-51 Laser - 06
OS 96 Specifications Optical data Measurement range 1) 60 2000mm Resolution 2) 1 5mm Light source Laser/L Wavelength 660nm (visible red light) Light spot Laser: divergent, 3x12mm² at 2m L: Ø 10mm Laser warning notice see remarks rror limits (relative to measurement distance) bsolute measurement accuracy 1) ±2% Repeatability 3) ±0.5% b/w detection thresholds (6%/90%) < 1% Timing Measurement time 10 100ms Response time 300ms elay before start-up 300ms lectrical data Operating voltage U 18 30V (incl. residual ripple) Residual ripple 15% of U ias current 150m Switching output PNP transistor, high-active Signal voltage high/low (U -2 V)/ 2V nalogue output voltage 1 10V, R L 2kΩ current 4 20m, R L 500Ω Indicators teach-in on GN teach-in on +U L green continuous light ready flashing fault teaching procedure no voltage L yellow continuous light object inside teach-in measurement distance flashing teaching procedure object outside teach-in measurement distance Mechanical data Metal housing Housing diecast zinc Optics cover glass Weight 380g onnection type M12 connector nvironmental data mbient temp. (operation/storage) -20 +50 / -30 +70 Protective circuit 4) 1, 2, 3 V safety class 5) II, all-insulated Protection class IP 67, IP 69K 6) Laser class 2 (acc. to N 60825-1) L class 1 (acc. to N 60825-1) Standards applied I 60947-5-2 1) Luminosity coefficient 6% 90%, over the entire temperature range, measurement object 50x50mm² 2) Minimum and maximum value depend on measurement distance 3) Same object, identical environmental conditions, measurement object 50x50mm² 4) 1=transient protection, 2=polarity reversal protection, 3=short-circuit protection for all outputs 5) Rating voltage 250V 6) IP 69K test acc. to IN 40050 part 9 simulated, high pressure cleaning conditions without the use of additives, acids and bases are not part of the test Order guide esignation F rea not defined Linearity not defined Measurement range Object present No object detected Measurement distance Part No. Tables iagrams Remarks Measurement time depends on the reflectivity of the measurement object and on the measurement mode. Teaching procedure: Position measured object at desired measurement distance. onnect teach input to +U for 2s. Reconnect teach input to GN, switching output is programmed. With M12 connector urrent output OS 96M/V-5140-420 500 35208 Voltage output OS 96M/V-5130-421 500 35165 OS 96M/V-51 Laser - 06 0706 43
OS 96 Optical laser distance sensors imensioned drawing 200 2000mm 18-30 V Reflection-independent distance information Highly insensitive to extraneous light nalogue current and voltage output Measurement range and mode adjustable Teachable switching output F G H I K L M Indicator diode green Indicator diode yellow Transmitter Receiver Optical axis evice plug M12x1 Screwed cable gland PG11 for Ø5 10mm ountersinking for SK nut M5, 4.2mm deep Parameter plug onnection terminals able entry Reference edge for the measurement (cover glass) U L US LIST lectrical connection We reserve the right to make changes ods_07e.fm I 60947... I 60947... ccessories: (available separately see page 88) IP 69K IP 67 Mounting systems able with M12 connector (K- ) onfiguration software onfiguration cable K-OS96-1500 Leuze electronic GmbH + o. KG Post-box 1111-73277 Owen-Teck Tel. +49 7021 5730 www.leuze.de 44 OS 96M/V Laser - 06
OS 96 Specifications Optical data Measurement range 1) 200 2000mm Resolution 2) 1 3mm Light source laser Wavelength 660nm (visible red light) Light spot divergent, 3x12mm² at 2m Laser warning notice see remarks rror limits (relative to measurement distance) bsolute measurement accuracy 1) ±2% Repeatability 3) ±0.5% b/w detect. thresholds (6 90% rem.) 1% Timing Measurement time 10 100ms Response time 300ms elay before start-up 300ms lectrical data Operating voltage U 18 30V (incl. residual ripple) Residual ripple 15% of U ias current 150m Switching output PNP transistor, high-active Signal voltage high/low (U -2 V)/ 2V nalogue output voltage 1 10V, R L 2kΩ current 4 20m, R L 500Ω Indicators teach-in on GN teach-in on +U L green continuous light ready flashing fault teaching procedure no voltage L yellow continuous light object inside teach-in measurement distance flashing teaching procedure object outside teach-in measurement distance Mechanical data Metal housing Housing diecast zinc Optics cover glass Weight 380g onnection type terminals or M12 connectors nvironmental data mbient temp. (operation/storage) -20 +50 / -30 +70 Protective circuit 4) 1, 2, 3 V safety class 5) II, all-insulated Protection class IP 67, IP 69K 6) Laser class 2 (acc. to N 60825-1) Standards applied I 60947-5-2 1) Luminosity coefficient 6% 90%, over the entire temperature range, measurement object 50x50mm² 2) Minimum and maximum value depend on measurement distance 3) Same object, identical environmental conditions, measurement object 50x50mm² 4) 1=transient protection, 2=polarity reversal protection, 3=short-circuit protection for all outputs 5) Rating voltage 250V 6) IP 69K test acc. to IN 40050 part 9 simulated, high pressure cleaning conditions without the use of additives, acids and bases are not part of the test Order guide F rea not defined Linearity not defined Measurement range Object present No object detected Measurement distance esignation Part No. UL Tables iagrams Remarks Measurement time depends on the reflectivity of the measurement object and on the measurement mode. Teaching procedure: Position measured object at desired measurement distance. onnect teach input to +U for 2s. Reconnect teach input to GN, switching output is programmed. With terminals urrent output OS 96M/V-5060-220 500 30595 Voltage output OS 96M/V-5070-221 500 30596 With M12 connector urrent output OS 96M/V-5060-420 500 30597 Voltage output OS 96M/V-5070-421 500 30598 OS 96M/V Laser - 06 0706 45
OS 96 Optical laser distance sensors imensioned drawing 200 2000mm 10-30 V Reflection-independent distance information Highly insensitive to extraneous light RS 232 or RS 485 interface Measurement range and mode adjustable Switching output (teachable with RS 232, adjustable with RS 485) F G H I K L M Indicator diode green Indicator diode yellow Transmitter Receiver Optical axis evice plug M12x1 Screwed cable gland PG11 for Ø5 10mm ountersinking for SK nut M5, 4.2mm deep Parameter plug onnection terminals able entry Reference edge for the measurement (cover glass) U L US LIST lectrical connection We reserve the right to make changes ods_03e.fm I 60947... I 60947... IP 67 ccessories: (available separately see page 88) Mounting systems able with M12 connector (K- ) onfiguration software onfiguration cable K-OS96-1500 Leuze electronic GmbH + o. KG Post-box 1111-73277 Owen-Teck Tel. +49 7021 5730 www.leuze.de 46 OS 96M/ Laser - 06
OS 96 Specifications Optical data Measurement range 1) 200 2000mm Resolution 2) 1 3mm Light source laser Wavelength 660nm (visible red light) Light spot divergent, 3x12mm² at 2m Laser warning notice see remarks rror limits (relative to measurement distance) bsolute measurement accuracy 1) ±2% Repeatability 3) ±0.5% b/w detection thresholds (6%/90%) < 1% Timing Measurement time 10 100ms Response time 300ms elay before start-up 300ms lectrical data Operating voltage U 10 30V (incl. residual ripple) Residual ripple 15% of U ias current 150m Switching output PNP transistor, high-active Signal voltage high/low (U -2V)/ 2V igital output RS 232 4) 9600 aud RS 485 3) 9600 aud, no termination Transmission protocol 5) 2 byte transmission, continuous data flow Indicators teach-in on GN teach-in on +U L green continuous light ready flashing fault teaching procedure no voltage L yellow continuous light objects inside teach-in measurement distance flashing teaching procedure object outside teach-in measurement distance Mechanical data Metal housing Housing diecast zinc Optics cover glass Weight 380g onnection type terminals or M12 connectors nvironmental data mbient temp. (operation/storage) -20 +50 / -30 +70 Protective circuit 6) 1, 2, 3 V safety class 7) II, all-insulated Protection class IP 67, IP 69K 8) Laser class 2 (acc. to N 60825-1) Standards applied I 60947-5-2 1) Luminosity coefficient 6% 90%, over complete temperature range, measured object 50x50mm² 2) Minimum and maximum value depend on measurement distance 3) Same object, identical environmental conditions, measurement object 50x50mm² 4) Higher baud rates can be set 5) 2byte transmission protocol 6) 1=transient protection, 2=polarity reversal protection, 3=short-circuit protection for all outputs 7) Rating voltage 250V 8) IP 69K test acc. to IN 40050 part 9 simulated, high pressure cleaning conditions without the use of additives, acids and bases are not part of the test Measurement value Order guide esignation Part No. UL Tables iagrams Remarks Measurement time depends on the reflectivity of the measurement object and on the measurement mode. Teaching procedure: Position measured object at desired measurement distance. onnect teach input to +U for 2s. Reconnect teach input to GN, switching output is programmed. With terminals RS 232 OS 96M/-5080-222 500 30599 RS 485 OS 96M/-5090-223 500 30600 With M12 connector RS 232 OS 96M/-5080-422 500 30601 RS 485 OS 96M/-5090-423 500 30602 OS 96M/ Laser - 06 0706 47
OS 96 Optical laser distance sensors imensioned drawing 200 2000mm 10-30 V Reflection-independent distance information Highly insensitive to extraneous light Measurement range and mode adjustable Two teachable switching outputs F G H I K L M Indicator diode green Indicator diode yellow Transmitter Receiver Optical axis evice plug M12x1 Screwed cable gland PG11 for Ø5 10mm ountersinking for SK nut M5, 4.2mm deep Parameter plug onnection terminals able entry Reference edge for the measurement (cover glass) lectrical connection We reserve the right to make changes ods_05e.fm I 60947... I 60947... ccessories: (available separately see page 88) IP 69K IP 67 Mounting systems able with M12 connector (K- ) onfiguration software onfiguration cable K-OS96-1500 Leuze electronic GmbH + o. KG Post-box 1111-73277 Owen-Teck Tel. +49 7021 5730 www.leuze.de 48 OS 96M/S Laser - 06
OS 96 Specifications Optical data Measurement range 1) 200 2000mm Resolution 2) 1 3mm Light source laser Wavelength 660nm (visible red light) Light spot divergent, 3x12mm² at 2m Laser warning notice see remarks rror limits (relative to measurement distance) bsolute measurement accuracy 1) ± 2% (relative to the measurement distance) Repeatability 3) ±0.5% b/w detect. thresholds (6 90% rem.) 1% Timing Measurement time 10 100ms Response time 300ms elay before start-up 300ms lectrical data Operating voltage U 10 30V (incl. residual ripple) Residual ripple 15% of U ias current 150m Switching outputs 2 PNP switching outputs, high-active Signal voltage high/low (U -2V)/ 2V Output current max. 100m per transistor output Indicators teach-in on GN teach-in on +U L green continuous light ready flashing fault teaching procedure no voltage L yellow continuous light object inside measurement range flashing object outside teaching procedure measurement range no object detected Mechanical data Metal housing Housing diecast zinc Optics cover glass Weight 380g onnection type terminals or M12 connectors nvironmental data mbient temp. (operation/storage) -20 +50 /-30 + 70 Protective circuit 4) 1, 2, 3 V safety class 5) II, all-insulated Protection class IP 67, IP 69K 6) Laser class 2 (acc. to N 60825-1) Standards applied I 60947-5-2 1) Luminosity coefficient 6% 90%, over complete temperature range, measured object 50x50mm² 2) Minimum and maximum value depend on measurement distance 3) Same object, identical environmental conditions, measurement object 50x50mm² 4) 1=transient protection, 2=polarity reversal protection, 3=short-circuit protection for all outputs 5) Rating voltage 250V 6) IP 69K test acc. to IN 40050 part 9 simulated, high pressure cleaning conditions without the use of additives, acids and bases are not part of the test Switching output (example) Hysteresis Switching point Q1 (teach point) Switching point Q2 (teach point) Measurement distance Tables iagrams Remarks Measurement time depends on the reflectivity of the measurement object and on the measurement mode. Teaching procedure: Position measured object at 1st desired measurement distance. onnect teach input to +U for 2s. oth Ls are flashing simultaneously. Reconnect teach input to GN, 1st switching output is programmed. Position measured object at 2nd desired measuring distance. onnect teach input to +U for 2s. oth Ls are flashing alternatingly. Reconnect teach input to GN, 2nd switching output is programmed. The procedure can be repeated as desired, leave teach input connected to GN in idle mode. Order guide esignation Part No. With terminals 2 PNP switching outputs OS 96M/S-5100-224 500 30603 With M12 connector 2 PNP switching outputs OS 96M/S-5100-424 500 30604 OS 96M/S Laser - 06 0706 49
OSL 96 Optical laser distance sensors imensioned drawing 150 2300mm 18-30 V Reflection-independent distance information Highly insensitive to extraneous light nalogue voltage output 1 10V (can be inverted, teachable) 2 teachable switching outputs (push-pull) asy alignment through visible red light F G H Indicator diode green Indicator diode yellow Transmitter Receiver Optical axis evice plug M12x1 ountersinking for SK nut M5, 4.2mm deep Teach button lectrical connection We reserve the right to make changes ods_25e.fm I 60947... I 60947... IP 67 ccessories: (available separately see page 88) Mounting systems able with M12 connector (K- ) Leuze electronic GmbH + o. KG Post-box 1111-73277 Owen-Teck Tel. +49 7021 5730 www.leuze.de 50 OSL 96K/V 66-2300-S12-06
OSL 96 Specifications Optical data Measurement range 1) 150 2300mm Resolution 2) 1 5mm Light source laser Wavelength 635nm (visible red light) Light spot divergent, 3x8mm² at 2300mm Laser warning notice see remarks rror limits (relative to measurement distance) bsolute measurement accuracy 1) ±3% Repeatability 3) ±2% b/w detect. thresholds (6 90% rem.) 1% Temperature drift 0.1%/ Timing Measurement time 2 7ms Response time 20ms elay before start-up 300ms lectrical data Operating voltage U 18 30V (incl. residual ripple) Residual ripple 15% of U ias current 150m Switching output/function 4) 2 push-pull switching outputs pin 2: Q2, PNP light switching, NPN dark switching pin 4: Q1, PNP light switching, NPN dark switching Signal voltage high/low (U -2V)/ 2V nalogue output voltage 1 10V, R L 2kΩ Indicators L green continuous light ready flashing (no Teach) fault, teach values were not applied no voltage L yellow continuous light object within teach-in measurement distance (output Q1 5) ) flashing (no Teach) teach values were not applied object outside teach-in measurement distance (output Q1 4) ) Mechanical data Housing plastic Optics cover plastic Weight 140g onnection type M12 connector nvironmental data mbient temp. (operation/storage) -20 +40 /-30 +70 Protective circuit 6) 1, 2, 3 V safety class 7) II, all-insulated Protection class IP 67 Laser class 2 (acc. to N 60825-1) Standards applied I 60947-5-2 1) Luminosity coefficient 6% 90%, at 20, measurement object 50x50mm² 2) Minimum and maximum value depend on measurement distance and configuration of the analogue output 3) Same object, identical environmental conditions, measurement object 50x50mm² 4) The push-pull switching outputs must not be connected in parallel 5) No display for output Q2 6) 1=transient protection, 2=polarity reversal protection, 3=short-circuit protection for all outputs 7) Rating voltage 250V Tables iagrams haracteristic curve of switching outputs: Hysteresis Switching point Q1 (teach point) Switching point Q2 (teach point) Measurement distance haracteristic curve of analogue output: F rea not defined Linearity not defined Measurement range Object present No object detected Measurement distance Remarks Measurement time depends on the reflectivity of the measurement object and on the measurement mode. Order guide esignation Part No. With M12 connector and analogue output OSL 96K/V 66-2300-S12 501 01881 OSL 96K/V 66-2300-S12-06 0706 51
OSL 96 T I teach-in with teach button 1.Position measurement object at the desired distance (➀). Optical laser distance sensors ➀ 2.The respective teach function is activated by operating the teach button (➁) for different amounts of time. The activated teach function is signalled by a flashing of the Ls. Teach function uration of teach button operation L green L yellow switching output Q1 2 4s flash synchronously switching output Q2 4 6s flash alternatingly 1V analogue output 6 8s on flashes 10V analogue output 8 10s flashes on ➁ Teach button 3.Release teach button (➁) and wait for optical confirmation by end of flashing signal (green L on). Reset of the analogue output to factory settings Reset 1V analogue output at 150mm: 1.Position measurement object just below start of measurement range (150mm). 2.Press teach button for 6 8s (green L on, yellow L flashes). 3.Release teach button and wait for optical confirmation by end of flashing signal (green L on). Reset 10V analogue output at 2300mm: 1.Position measurement object just beyond end of measurement range (2300mm). 2.Press teach button for 8 10s (green L flashes, yellow L on). 3.Release teach button and wait for optical confirmation by end of flashing signal (green L on). rror messages ontinuously flashing Ls signal an unsuccessful teach event (sensor not ready): L L rror green yellow flash synchronously teach switching output Q1 unsuccessful flash alternatingly teach switching output Q1 unsuccessful on flashes teach 1V analogue output unsuccessful flashes on teach 10V analogue output unsuccessful Remedy: Repeat teach event or Press teach button for more than 10s or isconnect sensor from voltage to restore the old values. Typical areas of application of optical distance sensors ontinuous distance measurement Positioning tasks Filling level control OSL 96 OSL 96 New stack OSL 96 Positioning Leuze electronic GmbH + o. KG Post-box 1111-73277 Owen-Teck Tel. +49 7021 5730 OSL 96K/V 66-2300-S12-06 www.leuze.de 52
Installation instructions Leuze electronic OSL 96 Mounting systems are available which have to be ordered separately at Leuze electronic. part from this, the drilled-through holes and threaded holes are suitable for the individual mounting of the OSL 96, depending on the area in which it is used. When mounting, avoid application of excessive force on the housing. Preferred movement of the objects Preferred mounting in connection to objects with structured surface View through a chase If the OSL 96 has to be installed behind a cover, the chase has to have at least the size of the optical glass cover. Otherwise, a correct measurement is not possible or can not be guaranteed. lignment to measurement objects with reflecting surfaces If the measurement object to be detected has a reflecting surface, a measurement may not be possible depending on the angle in which the light is reflected by the measurement object's surface. djust the angle between the sensor and the measurement object such that the sensor can reliably detect the measurement object. Working Safely ttention Laser Radiation! The optical distance sensors OSL 96 operate with a red light laser of class 2 acc. to N 60825-1. If you look into the beam path over a longer time period, the retina of your eye may be damaged! Never look directly into the beam path! o not point the laser beam of the OSL 96 at persons! When mounting and aligning the OSL 96 take care to avoid reflections of the laser beam reflective surfaces! The use of operating and adjusting devices other than those specified in the technical description, carrying out of differing procedures, or improper use of the optical laser distance sensor may lead to dangerous exposure to radiation! The use of optical instruments or devices in combination with the device increases the danger of eye damage! dhere to the applicable legal and local regulations regarding protection from laser beams acc. to N 60825-1 in its latest version. The OSL 96 uses a laser diode with low power in the visible red light range with an emitted wavelength of about 635nm. The glass optics cover is the only opening through which the laser radiation can escape from the device. The housing of the OSL 96 is sealed and has no parts that need to be adjusted or maintained by the user. The device must not be tampered with and must not be changed in any way! The destruction of the seal voids the warranty! Notice! It is important that you attach the sticky labels supplied to the device (notice signs and laser emission symbol)! If the signs would be covered due to the installation situation of the OSL 96, attach them close to the OSL 96 such that reading the notices cannot lead to looking into the laser beam! OSL 96K/V 66-2300-S12-06 0706 53
OSL 96 Optical laser distance sensors imensioned drawing 150 2300mm 10-30 V Reflection-independent distance information Highly insensitive to extraneous light 2 teachable switching outputs (push-pull) asy alignment through visible red light F G H Indicator diode green Indicator diode yellow Transmitter Receiver Optical axis evice plug M12x1 ountersinking for SK nut M5, 4.2mm deep Teach button lectrical connection We reserve the right to make changes ods_32e.fm I 60947... I 60947... IP 67 ccessories: (available separately see page 88) Mounting systems able with M12 connector (K- ) Leuze electronic GmbH + o. KG Post-box 1111-73277 Owen-Teck Tel. +49 7021 5730 www.leuze.de 54 OSL 96K/66-2300-S12-04
OSL 96 Specifications Optical data Measurement range 1) 150 2300mm Resolution 2) 1 5mm Hysteresis 2) 5 144mm Light source laser Wavelength 635nm (visible red light) Light spot divergent, 3x8mm² at 2300mm Laser warning notice see remarks rror limits (relative to measurement distance) bsolute measurement accuracy 1) ±3% Repeatability 3) ±2% b/w detect. thresholds (6 90% rem.) 1% Temperature drift 0.1%/ Timing Measurement time 2 7ms Response time 20ms elay before start-up 300ms lectrical data Operating voltage U 10 30V (incl. residual ripple) Residual ripple 15% of U ias current 150m Switching output/function 4) 2 push-pull switching outputs pin 2: Q2, PNP light switching, NPN dark switching pin 4: Q1, PNP light switching, NPN dark switching Signal voltage high/low (U -2V)/ 2V Indicators L green continuous light ready flashing (no Teach) fault, teach values were not applied no voltage L yellow continuous light object within teach-in measurement distance (output Q1 5) ) flashing (no Teach) teach values were not applied object outside teach-in measurement distance (output Q1 4) ) Mechanical data Housing plastic Optics cover plastic Weight 140g onnection type M12 connector nvironmental data mbient temp. (operation/storage) -20 +40 /-30 +70 Protective circuit 6) 1, 2, 3 V safety class 7) II, all-insulated Protection class IP 67 Laser class 2 (acc. to N 60825-1) Standards applied I 60947-5-2 1) Luminosity coefficient 6% 90%, at 20, measurement object 50x50mm² 2) Minimum and maximum value depend on measurement distance 3) Same object, identical environmental conditions, measurement object 50x50mm² 4) The push-pull switching outputs must not be connected in parallel 5) No display for output Q2 6) 1=transient protection, 2=polarity reversal protection, 3=short-circuit protection for all outputs 7) Rating voltage 250V Tables iagrams haracteristic curve of switching outputs: Hysteresis Switching point Q1 (teach point) Switching point Q2 (teach point) Measurement distance Remarks Measurement time depends on the reflectivity of the measurement object and on the measurement mode. Order guide esignation Part No. With M12 connector and 2 switching outputs OSL 96K/66-2300-S12 501 01882 OSL 96K/66-2300-S12-04 0706 55
OSL 96 T I teach-in with teach button 1.Position measurement object at the desired distance (➀). Optical laser distance sensors ➀ 2.The respective teach function is activated by operating the teach button (➁) for different amounts of time. The activated teach function is signalled by a flashing of the Ls. Teach function uration of teach button operation L green L yellow switching output Q1 2 4s flash synchronously switching output Q2 4 6s flash alternatingly 3.Release teach button (➁) and wait for optical confirmation by end of flashing signal (green L on). ➁ Teach button T I teach-in via input 1.Position measurement object at the desired distance. 2.The respective teach function is activated by applying +U to teach input (pin 5). The teach event is signalled by flashing of the Ls. Teach function uration of the teach signal L green L yellow switching output Q1 2 4s flash synchronously switching output Q2 4 6s flash alternatingly 3.To finish the teach event, disconnect the teach input from +U or switch it to 0V after the desired time. 4. successful teach event is signalled by the end of the flashing (green L on) rror messages ontinuously flashing Ls signal an unsuccessful teach event (sensor not ready): L L green yellow flash synchronously flash alternatingly rror teach switching output Q1 unsuccessful teach switching output Q1 unsuccessful Remedy: Repeat teach event or Press teach button for more than 10s or isconnect sensor from voltage to restore the old values. Typical areas of application of optical distance sensors ontinuous distance measurement Positioning tasks Filling level control OSL 96 OSL 96 New stack OSL 96 Positioning Leuze electronic GmbH + o. KG Post-box 1111-73277 Owen-Teck Tel. +49 7021 5730 OSL 96K/66-2300-S12-04 www.leuze.de 56
Installation instructions Leuze electronic OSL 96 Mounting systems are available which have to be ordered separately at Leuze electronic. part from this, the drilled-through holes and threaded holes are suitable for the individual mounting of the OSL 96, depending on the area in which it is used. When mounting, avoid application of excessive force on the housing. Preferred movement of the objects Preferred mounting in connection to objects with structured surface View through a chase If the OSL 96 has to be installed behind a cover, the chase has to have at least the size of the optical glass cover. Otherwise, a correct measurement is not possible or can not be guaranteed. lignment to measurement objects with reflecting surfaces If the measurement object to be detected has a reflecting surface, a measurement may not be possible depending on the angle in which the light is reflected by the measurement object's surface. djust the angle between the sensor and the measurement object such that the sensor can reliably detect the measurement object. Working Safely ttention Laser Radiation! The optical distance sensors OSL 96 operate with a red light laser of class 2 acc. to N 60825-1. If you look into the beam path over a longer time period, the retina of your eye may be damaged! Never look directly into the beam path! o not point the laser beam of the OSL 96 at persons! When mounting and aligning the OSL 96 take care to avoid reflections of the laser beam reflective surfaces! The use of operating and adjusting devices other than those specified in the technical description, carrying out of differing procedures, or improper use of the optical laser distance sensor may lead to dangerous exposure to radiation! The use of optical instruments or devices in combination with the device increases the danger of eye damage! dhere to the applicable legal and local regulations regarding protection from laser beams acc. to N 60825-1 in its latest version. The OSL 96 uses a laser diode with low power in the visible red light range with an emitted wavelength of about 635nm. The glass optics cover is the only opening through which the laser radiation can escape from the device. The housing of the OSL 96 is sealed and has no parts that need to be adjusted or maintained by the user. The device must not be tampered with and must not be changed in any way! The destruction of the seal voids the warranty! Notice! It is important that you attach the sticky labels supplied to the device (notice signs and laser emission symbol)! If the signs would be covered due to the installation situation of the OSL 96, attach them close to the OSL 96 such that reading the notices cannot lead to looking into the laser beam! OSL 96K/66-2300-S12-04 0706 57
OS 96 Optical laser distance sensors imensioned drawing 250 5000mm 18-30 V Reflection-independent distance information Highly insensitive to extraneous light nalogue current or voltage output Measurement range and mode adjustable Teachable switching output 2 PNP switching outputs asy alignment through visible red light F G H I Indicator diode green Indicator diode yellow Transmitter Receiver Optical axis evice plug M12x1 ountersinking for SK nut M5, 4.2mm deep Parameter plug Reference edge for the measurement (cover glass) U L US LIST lectrical connection We reserve the right to make changes ods_09e.fm I 60947... I 60947... ccessories: (available separately see page 88) IP 69K IP 67 Mounting systems able with M12 connector (K- ) onfiguration software onfiguration cable K-OS96-1500 Leuze electronic GmbH + o. KG Post-box 1111-73277 Owen-Teck Tel. +49 7021 5730 www.leuze.de 58 OS 96M/V-5... Laser - 08
OS 96 Specifications Optical data Measurement range 1) 250 5000mm Resolution 2) 1 20mm Light source laser Wavelength 660nm (visible red light) Light spot divergent, 3x12mm² at 2000mm Laser warning notice see remarks rror limits (relative to measurement distance) bsolute measurement accuracy 1) ± 2.5% up to 3m/± 5% at 3 5m Repeatability 3) ± 2% up to 3m/± 3% at 3 5m b/w detect. thresholds (6 90% rem.) 2% up to 3m/ 3% at 3 5m Timing Measurement time 10 100ms Response time 300ms elay before start-up 300ms lectrical data Operating voltage U 18 30V (incl. residual ripple) Residual ripple 15% of U ias current 150m Switching output PNP transistor, high-active Signal voltage high/low (U -2V)/ 2V nalogue output voltage 1 10V, R L 2kΩ current 4 20m, R L 500Ω Indicators teach-in on GN teach-in on +U L green continuous light ready flashing fault teaching procedure no voltage L yellow continuous light object inside teach-in measurement distance flashing teaching procedure object outside teach-in measurement distance Mechanical data Metal housing Housing diecast zinc Optics cover glass Weight 380g onnection type M12 connector nvironmental data mbient temp. (operation/storage) -20 +40 /-30 +70 Protective circuit 4) 1, 2, 3 V safety class 5) II, all-insulated Protection class IP 67, IP 69K 6) Laser class 2 (acc. to N 60825-1) Standards applied I 60947-5-2 1) Luminosity coefficient from 6% 90%, over complete temperature range, measured object 50x50mm² 2) Minimum and maximum value depend on measurement distance and configuration of the analogue output 3) Same object, identical environmental conditions, measurement object 50x50mm² 4) 1=transient protection, 2=polarity reversal protection, 3=short-circuit protection for all outputs 5) Rating voltage 250V 6) IP 69K test acc. to IN 40050 part 9 simulated, high pressure cleaning conditions without the use of additives, acids and bases are not part of the test Tables Remarks Measurement time depends on the reflectivity of the measurement object and on the measurement mode. Teaching procedure: (for OS 96M/V-5510-420 and OS 96M/V-5480-421) Position measured object at desired measurement distance. onnect teach input to +U for 2s. Reconnect teach input to GN, switching output is programmed. F rea not defined Linearity not defined Measurement range Object present No object detected Measurement distance Order guide esignation Part No. UL With M12 connector urrent output and PNP switching output OS 96M/V-5510-420 500 35216 Voltage output and PNP switching output OS 96M/V-5480-421 500 36255 urrent output and 2 PNP switching outputs OS 96M/V-5520-426 500 37963 OS 96M/V-5... Laser - 08 0706 59
OS 96 Optical distance sensors imensioned drawing 100 600mm 18-30 V Reflection-independent distance information Highly insensitive to extraneous light nalogue current or voltage output P/OL display and key pad for configuration Measurement value is indicated in mm on OL display Measurement range and mode adjustable Teachable switching output and analogue output F G H I Indicator diode green Indicator diode yellow Transmitter Receiver Optical axis evice plug M12x1 ountersinking for SK nut M5, 4.2mm deep OL display and key pad Reference edge for the measurement (cover glass) U L US LIST lectrical connection We reserve the right to make changes ods_41gb.fm I 60947... I 60947... ccessories: IP 69K IP 67 (available separately see page 88) Mounting systems able with M12 connector (K- ) onfiguration software Leuze electronic GmbH + o. KG Post-box 1111-73277 Owen-Teck Tel. +49 7021 5730 www.leuze.de 60 OS 96 M/6-600-S12-03 OS 96 M/V6-600-S12-03
OS 96 Specifications Optical data Measurement range 1) 100 600mm Resolution 2) 0.1 0.5mm Light source L Wavelength 880nm (infrared light) Light spot approx. 15 x 15mm 2 at 600mm rror limits (relative to measurement distance) bsolute measurement accuracy 1) ±1.5% Repeatability 3) ±0.5% b/w detect. thresholds (6 90% rem.) 1% Temperature compensation yes 4) Timing Measurement time 1 5 1) ms Response time 1) 15ms elay before start-up 300ms lectrical data 5) Operating voltage U 18 30V (incl. residual ripple) Residual ripple 15% of U ias current 150m Switching output push-pull switching output 6), PNP light switching, NPN dark switching Signal voltage high/low (U -2 V)/ 2V nalogue output voltage 1 10V, R L 2kΩ current 4 20m, R L 500Ω Indicators teach-in on GN teach-in on +U L green continuous light ready flashing fault teaching procedure no voltage L yellow continuous light object inside teach-in measurement distance flashing teaching procedure object outside teach-in measurement distance Mechanical data Metal housing Housing diecast zinc Optics cover glass Weight 380g onnection type M12 connector nvironmental data mbient temp. (operation/storage) -20 +50 / -30 +70 Protective circuit 7) 1, 2, 3 V safety class 8) II, all-insulated Protection class IP 67, IP 69K 9) L class 1 (acc. to N 60825-1) Standards applied I 60947-5-2 1) Luminosity coefficient 6% 90%, complete measurement range, at 20, medium range of U, measurement object 50x50mm² 2) Minimum and maximum value depend on measurement distance 3) Same object, identical environmental conditions, measurement object 50x50mm² 4) Typ. ± 0.02 %/K 5) For UL applications: for use in class 2 circuits according to N only 6) The push-pull switching outputs must not be connected in parallel 7) 1=transient protection, 2=polarity reversal protection, 3=short-circuit protection for all outputs 8) Rating voltage 250V, with cover closed 9) IP 69K test acc. to IN 40050 part 9 simulated, high pressure cleaning conditions without the use of additives. cids and bases are not part of the test. F rea not defined Linearity not defined Measurement range Object present No object detected Measurement distance Tables iagrams Remarks Measurement time depends on the reflectivity of the measurement object and on the measurement mode. Order guide esignation Part No. UL With M12 connector urrent output OS 96 M/6-600-S12 501 06720 Voltage output OS 96 M/V6-600-S12 501 06721 OS 96 M/6-600-S12-03 0706 OS 96 M/V6-600-S12-03 61
OSR 96 Optical distance sensors imensioned drawing 100 600mm 18-30 V Reflection-independent distance information Highly insensitive to extraneous light nalogue current or voltage output P/OL display and key pad for configuration Measurement value is indicated in mm on OL display Measurement range and mode adjustable Teachable switching output and analogue output F G H I Indicator diode green Indicator diode yellow Transmitter Receiver Optical axis evice plug M12x1 ountersinking for SK nut M5, 4.2mm deep OL display and key pad Reference edge for the measurement (cover glass) U L US LIST lectrical connection We reserve the right to make changes ods_42gb.fm I 60947... I 60947... ccessories: IP 69K IP 67 (available separately see page 88) Mounting systems able with M12 connector (K- ) onfiguration software Leuze electronic GmbH + o. KG Post-box 1111-73277 Owen-Teck Tel. +49 7021 5730 www.leuze.de 62 OSR 96 M/6-600-S12-03 OSR 96 M/V6-600-S12-03
OSR 96 Specifications Optical data Measurement range 1) 100 600mm Resolution 2) 0.1 0.5mm Light source L Wavelength 635nm (visible red light) Light spot approx. 15 x 15mm 2 at 600mm Laser warning notice see remarks rror limits (relative to measurement distance) bsolute measurement accuracy 1) ±1.5% Repeatability 3) ±0.5% b/w detect. thresholds (6 90% rem.) 1% Temperature compensation yes 4) Timing Measurement time 1 5 1) ms Response time 1) 15ms elay before start-up 300ms lectrical data 5) Operating voltage U 18 30V (incl. residual ripple) Residual ripple 15% of U ias current 150m Switching output push-pull switching output 6), PNP light switching, NPN dark switching Signal voltage high/low (U -2 V)/ 2V nalogue output voltage 1 10V, R L 2kΩ current 4 20m, R L 500Ω Indicators teach-in on GN teach-in on +U L green continuous light ready flashing fault teaching procedure no voltage L yellow continuous light object inside teach-in measurement distance flashing teaching procedure object outside teach-in measurement distance Mechanical data Metal housing Housing diecast zinc Optics cover glass Weight 380g onnection type M12 connector nvironmental data mbient temp. (operation/storage) -20 +50 / -30 +70 Protective circuit 7) 1, 2, 3 V safety class 8) II, all-insulated Protection class IP 67, IP 69K 9) L class 1 (acc. to N 60825-1) Standards applied I 60947-5-2 1) Luminosity coefficient 6% 90%, complete measurement range, at 20, medium range of U, measurement object 50x50mm² 2) Minimum and maximum value depend on measurement distance 3) Same object, identical environmental conditions, measurement object 50x50mm² 4) Typ. ± 0.02 %/K 5) For UL applications: for use in class 2 circuits according to N only 6) The push-pull switching outputs must not be connected in parallel 7) 1=transient protection, 2=polarity reversal protection, 3=short-circuit protection for all outputs 8) Rating voltage 250V, with cover closed 9) IP 69K test acc. to IN 40050 part 9 simulated, high pressure cleaning conditions without the use of additives. cids and bases are not part of the test. F rea not defined Linearity not defined Measurement range Object present No object detected Measurement distance Tables iagrams Remarks Measurement time depends on the reflectivity of the measurement object and on the measurement mode. Order guide esignation Part No. UL With M12 connector urrent output OSR 96 M/6-600-S12 501 06730 Voltage output OSR 96 M/V6-600-S12 501 06731 OSR 96 M/6-600-S12-03 0706 OSR 96 M/V6-600-S12-03 63
OSL 96 Optical distance sensors imensioned drawing 150 800mm 18-30 V Reflection-independent distance information Highly insensitive to extraneous light nalogue current or voltage output P/OL display and key pad for configuration Measurement value is indicated in mm on OL display Measurement range and mode adjustable Teachable switching output and analogue output F G H I Indicator diode green Indicator diode yellow Transmitter Receiver Optical axis evice plug M12x1 ountersinking for SK nut M5, 4.2mm deep OL display and key pad Reference edge for the measurement (cover glass) U L US LIST lectrical connection We reserve the right to make changes ods_43gb.fm I 60947... I 60947... ccessories: IP 69K IP 67 (available separately see page 88) Mounting systems able with M12 connector (K- ) onfiguration software Leuze electronic GmbH + o. KG Post-box 1111-73277 Owen-Teck Tel. +49 7021 5730 www.leuze.de 64 OSL 96 M/6-800-S12-01 OSL 96 M/V6-800-S12-01
OSL 96 Specifications Optical data Measurement range 1) 150 800mm Resolution 2) 0.1 0.8mm Light source laser Wavelength 655nm (red light) Light spot approx. 1 x 1mm 2 at 800mm rror limits (relative to measurement distance) bsolute measurement accuracy 1) ±1.5% Repeatability 3) ±0.5% b/w detect. thresholds (6 90% rem.) 1% Temperature compensation yes 4) Timing Measurement time 1 5 1) ms Response time 1) 15ms elay before start-up 300ms lectrical data 5) Operating voltage U 18 30V (incl. residual ripple) Residual ripple 15% of U ias current 150m Switching output push-pull switching output 6), PNP light switching, NPN dark switching Signal voltage high/low (U -2 V)/ 2V nalogue output voltage 1 10V, R L 2kΩ current 4 20m, R L 500Ω Indicators teach-in on GN teach-in on +U L green continuous light ready flashing fault teaching procedure no voltage L yellow continuous light object inside teach-in measurement distance flashing teaching procedure object outside teach-in measurement distance Mechanical data Metal housing Housing diecast zinc Optics cover glass Weight 380g onnection type M12 connector nvironmental data mbient temp. (operation/storage) -20 +50 / -30 +70 Protective circuit 7) 1, 2, 3 V safety class 8) II, all-insulated Protection class IP 67, IP 69K 9) Laser class 2 (acc. to N 60825-1) Standards applied I 60947-5-2 1) Luminosity coefficient 6% 90%, complete measurement range, at 20, medium range of U, measurement object 50x50mm² 2) Minimum and maximum value depend on measurement distance 3) Same object, identical environmental conditions, measurement object 50x50mm² 4) Typ. ± 0.02 %/K 5) For UL applications: for use in class 2 circuits according to N only 6) The push-pull switching outputs must not be connected in parallel 7) 1=transient protection, 2=polarity reversal protection, 3=short-circuit protection for all outputs 8) Rating voltage 250V, with cover closed 9) IP 69K test acc. to IN 40050 part 9 simulated, high pressure cleaning conditions without the use of additives. cids and bases are not part of the test. F rea not defined Linearity not defined Measurement range Object present No object detected Measurement distance Tables iagrams Remarks Measurement time depends on the reflectivity of the measurement object and on the measurement mode. Order guide esignation Part No. With M12 connector urrent output OSL 96 M/6-800-S12 501 06728 Voltage output OSL 96 M/V6-800-S12 501 06729 OSL 96 M/6-800-S12-01 0706 OSL 96 M/V6-800-S12-01 65
OSL 96 Optical laser distance sensors imensioned drawing 150 2000mm 18-30 V Reflection-independent distance information Highly insensitive to extraneous light nalogue current or voltage output P/OL display and key pad for configuration Measurement value is indicated in mm on OL display Measurement range and mode adjustable Teachable switching output and analogue output F G H I Indicator diode green Indicator diode yellow Transmitter Receiver Optical axis evice plug M12x1 ountersinking for SK nut M5, 4.2mm deep OL display and key pad Reference edge for the measurement (cover glass) U L US LIST lectrical connection We reserve the right to make changes ods_40gb.fm I 60947... I 60947... ccessories: IP 69K IP 67 (available separately see page 88) Mounting systems able with M12 connector (K- ) onfiguration software Leuze electronic GmbH + o. KG Post-box 1111-73277 Owen-Teck Tel. +49 7021 5730 www.leuze.de 66 OSL 96 M/6-2000-S12-03 OSL 96 M/V6-2000-S12-03
OSL 96 Specifications Optical data Measurement range 1) 150 2000mm Resolution 2) 1 3mm Light source laser Wavelength 655nm (visible red light) Light spot divergent, 2x6mm² at 2m Laser warning notice see remarks rror limits (relative to measurement distance) bsolute measurement accuracy 1) ±1.5% Repeatability 3) ±0.5% b/w detect. thresholds (6 90% rem.) 1% Temperature compensation yes 4) Timing Measurement time 1 5 1) ms Response time 1) 15ms elay before start-up 300ms lectrical data 5) Operating voltage U 18 30V (incl. residual ripple) Residual ripple 15% of U ias current 150m Switching output push-pull switching output 6), PNP light switching, NPN dark switching Signal voltage high/low (U -2 V)/ 2V nalogue output voltage 1 10V, R L 2kΩ current 4 20m, R L 500Ω Indicators teach-in on GN teach-in on +U L green continuous light ready flashing fault teaching procedure no voltage L yellow continuous light object inside teach-in measurement distance flashing teaching procedure object outside teach-in measurement distance Mechanical data Metal housing Housing diecast zinc Optics cover glass Weight 380g onnection type M12 connector nvironmental data mbient temp. (operation/storage) -20 +50 / -30 +70 Protective circuit 7) 1, 2, 3 V safety class 8) II, all-insulated Protection class IP 67, IP 69K 9) Laser class 2 (acc. to N 60825-1) Standards applied I 60947-5-2, UL 508 1) Luminosity coefficient 6% 90%, complete measurement range, at 20, medium range of U, measurement object 50x50mm² 2) Minimum and maximum value depend on measurement distance 3) Same object, identical environmental conditions, measurement object 50x50mm² 4) Typ. ± 0.02 %/K 5) For UL applications: for use in class 2 circuits according to N only 6) The push-pull switching outputs must not be connected in parallel 7) 1=transient protection, 2=polarity reversal protection, 3=short-circuit protection for all outputs 8) Rating voltage 250V, with cover closed 9) IP 69K test acc. to IN 40050 part 9 simulated, high pressure cleaning conditions without the use of additives. cids and bases are not part of the test. F rea not defined Linearity not defined Measurement range Object present No object detected Measurement distance Tables iagrams Remarks Measurement time depends on the reflectivity of the measurement object and on the measurement mode. Order guide esignation Part No. UL With M12 connector urrent output OSL 96 M/6-2000-S12 501 06593 Voltage output OSL 96 M/V6-2000-S12 501 06594 OSL 96 M/6-2000-S12-03 0706 OSL 96 M/V6-2000-S12-03 67
OSL 30 Optical laser distance sensors imensioned drawing 0.2 30m 18-30 V Reflection-independent distance information High accuracy through referencing nalogue current and voltage output 1 teachable analogue and switching output L display and key pad for configuration Measurement value is indicated in mm on L display M12 connector Mounting device included F G 1 green indicator diode / ready 3 yellow indicator diodes / switching outputs Q1, Q2, Q3 Optical axes Transmitter Receiver Reference edge for the measurement (distance zero point) Sight for coarse alignment U L US LIST lectrical connection We reserve the right to make changes ods_13e.fm I 60947... I 60947... IP 67 ccessories: (available separately see page 90) Ready-made cable K- M12-8P-2m-PUR o-operative Target TS 100x100 (reflectivity 50 90%) Leuze electronic GmbH + o. KG Post-box 1111-73277 Owen-Teck Tel. +49 7021 5730 www.leuze.de 68 OSL 30/V-30M-S12-04
OSL 30 Specifications Optical data Measurement range 1) Resolution 2) Light source Wavelength Light spot Laser warning notice rror limits bsolute measurement accuracy 3) Repeatability 3) 4) Temperature drift Timing Measurement time 5) elay before start-up lectrical data Operating voltage U Residual ripple Power consumption Switching output 0.2 30m (adjustable) 0.1mm/1mm (factory setting) laser 650nm (visible red light) divergent, 6mm at 10m see remarks ± 5mm (6 90% diffuse reflection) ± 2mm (90% diffuse reflection) after referencing ± 2mm (6 90% diffuse reflection) typ. 0.5mm/ (without referencing) 30 100ms (factory setting: 100ms) 1s 18 30V (incl. residual ripple) 15% of U 4W PNP transistor, HIGH active (default), NPN transistor or push-pull through configuration Signal voltage high/low (U -2 V)/ 2V nalogue output R L 2kΩ (voltage) R L 500Ω (current) Indicators L green continuous light ready no voltage L yellow continuous light object inside teach-in measurement distance object outside teach-in measurement distance Mechanical data Housing metal Optics cover glass Weight 650g onnection type M12 connector, 8-pin nvironmental data mbient temp. (operation/storage) 0 +45 /-40 +70 Protective circuit 6) 2, 3 V safety class 7) II, all-insulated Protection class IP 67 Laser class 2 (acc. to N 60825-1) Standards applied I 60947-5-2 1) Luminosity coefficient 6%... 90%, over mentioned temperature range, measured object 50x50mm² 2) isplay and output resolution 0.1mm configurable 3) Minimum value depends on configuration of analogue output 4) Same object, identical environmental conditions, measurement object 50x50mm² 5) onfigurable, depends on the reflectivity of the object and on the max. detection range 6) 2=polarity reversal protection, 3=short-circuit protection for all outputs 7) Rating voltage 250V Remarks Measurement time: configurable, depends on the reflectivity of the object and on the measurement mode. Teaching procedure (factory setting): Position measurement object at the desired measurement distance. pply +U to the teach input. Take teach input back to GN, switching output has now been taught. dge on line teach Q1 teaches output Q1. uring the teaching of Q1, yellow L Q1 will flash. ctivation/referencing input: Referencing is carried out by applying the voltage (for a duration of about 300ms). If this process is activated before the measurement, the highest possible accuracy is achieved. The enclosed laser warning signs must be attached to the sensor or in its immediate vicinity such that they are well visible. F Short range (no signal) Object present Measurement range Object present No object present (no signal) Measurement distance Order guide esignation Part No. M12 connector OSL 30/V-30M-S12 500 39447 OSL 30/V-30M-S12-04 0601 69
OSL 30 Optical laser distance sensors imensioned drawing 0.2 30m 10-30 V Reflection-independent distance information High accuracy through referencing RS 232 interface 2 teachable switching outputs L display and key pad for configuration Measurement value is indicated in mm on L display M12 connector Mounting device included onnection option for a coupling module, e.g. for Profibus F G 1 green indicator diode / ready 3 yellow indicator diodes / switching outputs Q1, Q2, Q3 Optical axes Transmitter Receiver Reference edge for the measurement (distance zero point) Sight for coarse alignment U L US LIST lectrical connection We reserve the right to make changes ods_16e.fm I 60947... I 60947... IP 67 ccessories: (available separately see page 90) Ready-made cable K- M12-8P-2m-PUR o-operative Target TS 100x100 (reflectivity 50 90%) Leuze electronic GmbH + o. KG Post-box 1111-73277 Owen-Teck Tel. +49 7021 5730 www.leuze.de 70 OSL 30/ 232-30M-S12-05
OSL 30 Specifications Optical data Measurement range 1) 0.2 30m Resolution 2) 0.1mm/1mm (factory setting) Light source laser Wavelength 650nm (visible red light) Light spot divergent, 6mm at 10m Laser warning notice see remarks rror limits bsolute measurement accuracy 1) ± 5mm (6 90% diffuse reflection) ± 2mm (90% diffuse reflection) after referencing Repeatability 3) ± 2mm (6 90% diffuse reflection) Temperature drift typ. 0.5mm/ (without referencing) Timing Measurement time 4) 30 100ms (factory setting: 100ms) elay before start-up 1s lectrical data Operating voltage U 10 30V (incl. residual ripple) Residual ripple 15% of U Power consumption 4W Switching outputs PNP transistor, HIGH active (default), NPN transistor or push-pull through configuration Signal voltage high/low (U -2 V)/ 2V Serial interface RS 232, 9600aud default setting Indicators L green continuous light ready no voltage L yellow continuous light object inside teach-in measurement distance object outside teach-in measurement distance Mechanical data Housing metal Optics cover glass Weight 650g onnection type M12 connector, 8-pin nvironmental data mbient temp. (operation/storage) 0 +45 /-40 +70 Protective circuit 5) 2, 3 V safety class 6) II, all-insulated Protection class IP 67 Laser class 2 (acc. to N 60825-1) Standards applied I 60947-5-2 1) Luminosity coefficient 6% 90%, for constant environmental conditions, measurement object 50x50mm² 2) isplay and output resolution 0.1mm configurable 3) Same object, identical environmental conditions, measurement object 50x50mm² 4) onfigurable, depends on the reflectivity of the object and on the max. detection range 5) 2=polarity reversal protection, 3=short-circuit protection for all outputs 6) Rating voltage 250V xample 1: SII transmission of the measurement value Transmission format: MMMMM<R> MMMMM = 5-digit measurement value <R> = SII character "arriage Return" (x0) xample 2: measurement value = 16 it 1. Low-yte 2. Middle-yte 3. High-yte it 0 = 0; it 1 = 0 it 0 = 1; it 1 = 0 it 0 = 0; it 1 = 1 7 0 7 0 7 0 0 0 0 1 x x 1 0 it 5 it 4 it 3 it 2 it 1 it 0 (LS) Order guide it 11 it 10 it 9 it 8 it 7 it 6 don t care don t care it 15 (MS) it 14 it 13 it 12 esignation Part No. With M12 connector OSL 30/ 232-30M-S12 500 41203 Remarks Measurement time: configurable, depends on the reflectivity of the object and on the measurement mode. Teaching procedure (factory setting): Position measurement object at the desired measurement distance. pply +U to the teach input. Take teach input back to GN, switching output has now been taught. First edge on line teach Q1/Q2 teaches output Q1, second edge teaches Q2. uring the teaching of Q1, the yellow L Q1 will flash. uring the teaching of Q2, the yellow L Q2 will flash. ctivation/referencing input: Referencing is carried out by applying the voltage (for a duration of about 300ms). If this process is activated before the measurement, the highest possible accuracy is achieved. Possible protocols for the serial interface, selectable through configuration. 1. istance output in SII 2. Measurement value=14/16/20 bit (measurement distance up to 15000mm at a resolution of 1mm / 30000mm at a resolution of 1mm / 30000mm at a resolution of 0.1mm) 3. Remote control, SII transfer of the measurement value on request: 4 bytes (measurement distance up to 9900mm), 5/6 bytes (measurement distance up to 30000mm). The enclosed laser warning signs must be attached to the sensor or in its immediate vicinity such that they are well visible. OSL 30/ 232-30M-S12-05 0706 71
OSL 30 Optical laser distance sensors imensioned drawing 0.2 30m 10-30 V Reflection-independent distance information High accuracy through referencing RS 485 interface 2 teachable switching outputs L display and key pad for configuration Measurement value is indicated in mm on L display M12 connector Mounting device included onnection option for a coupling module, e.g. for Profibus F G 1 green indicator diode / ready 3 yellow indicator diodes / switching outputs Q1, Q2, Q3 Optical axes Transmitter Receiver Reference edge for the measurement (distance zero point) Sight for coarse alignment U L US LIST lectrical connection We reserve the right to make changes ods_14e.fm I 60947... I 60947... IP 67 ccessories: (available separately see page 90) Ready-made cable K- M12-8P-2m-PUR o-operative Target TS 100x100 (reflectivity 50 90%) Leuze electronic GmbH + o. KG Post-box 1111-73277 Owen-Teck Tel. +49 7021 5730 www.leuze.de 72 OSL 30/ 485-30M-S12-05
OSL 30 Specifications Optical data Measurement range 1) 0.2 30m Resolution 2) 0.1mm/1mm (factory setting) Light source laser Wavelength 650nm (visible red light) Light spot divergent, 6mm at 10m Laser warning notice see remarks rror limits bsolute measurement accuracy 1) ± 5mm (6 90% diffuse reflection) ± 2mm (90% diffuse reflection) after referencing Repeatability 3) ± 2mm (6 90% diffuse reflection) Temperature drift typ. 0.5mm/ (without referencing) Timing Measurement time 4) 30 100ms (factory setting: 100ms) elay before start-up 1s lectrical data Operating voltage U 10 30V (incl. residual ripple) Residual ripple 15% of U Power consumption 4W Switching outputs PNP transistor, HIGH active (default), NPN transistor or push-pull through configuration Signal voltage high/low (U -2 V)/ 2V Serial interface RS 485, 9600aud, no termination Indicators L green continuous light ready no voltage L yellow continuous light object inside teach-in measurement distance object outside teach-in measurement distance Mechanical data Housing metal Optics cover glass Weight 650g onnection type M12 connector, 8-pin nvironmental data mbient temp. (operation/storage) 0 +45 /-40 +70 Protective circuit 5) 2, 3 V safety class 6) II, all-insulated Protection class IP 67 Laser class 2 (acc. to N 60825-1) Standards applied I 60947-5-2 1) Luminosity coefficient 6% 90%, for constant environmental conditions, measurement object 50x50mm² 2) isplay and output resolution 0.1mm configurable 3) Same object, identical environmental conditions, measurement object 50x50mm² 4) onfigurable, depends on the reflectivity of the object and on the max. detection range 5) 2=polarity reversal protection, 3=short-circuit protection for all outputs 6) Rating voltage 250V xample 1: SII transmission of the measurement value Transmission format: MMMMM<R> MMMMM = 5-digit measurement value <R> = SII character "arriage Return" (x0) xample 2: measurement value = 16 it 1. Low-yte 2. Middle-yte 3. High-yte it 0 = 0; it 1 = 0 it 0 = 1; it 1 = 0 it 0 = 0; it 1 = 1 7 0 7 0 7 0 0 0 0 1 x x 1 0 it 5 it 4 it 3 it 2 it 1 it 0 (LS) Order guide it 11 it 10 it 9 it 8 it 7 it 6 don t care don t care it 15 (MS) it 14 it 13 it 12 esignation Part No. With M12 connector OSL 30/ 485-30M-S12 500 41204 Remarks Measurement time: configurable, depends on the reflectivity of the object and on the measurement mode. Teaching procedure (factory setting): Position measurement object at the desired measurement distance. pply +U to the teach input. Take teach input back to GN, switching output has now been taught. First edge on line teach Q1/Q2 teaches output Q1, second edge teaches Q2. uring the teaching of Q1, the yellow L Q1 will flash. uring the teaching of Q2, the green L and the yellow L Q2 will flash. ctivation/referencing input: Referencing is carried out by applying the voltage (for a duration of about 300ms). If this process is activated before the measurement, the highest possible accuracy is achieved. Possible protocols for the serial interface, selectable through configuration. 1. istance output in SII 2. Measurement value=14/16/20 bit (measurement distance up to 15,000mm at a resolution of 1mm / 30,000mm at a resolution of 1mm / 30,000mm at a resolution of 0.1mm) 3. Remote control, SII transfer of the measurement value on request (compatible to itbus): 4 bytes (measurement distance up to 9900mm), 5/6 bytes (measurement distance up to 30000mm). The enclosed laser warning signs must be attached to the sensor or in its immediate vicinity such that they are well visible. OSL 30/ 485-30M-S12-05 0706 73
OSL 30 Optical laser distance sensors imensioned drawing 0.2 30m 10-30 V Reflection-independent distance information High accuracy through referencing 3 teachable switching outputs L display and key pad for configuration Measurement value is indicated in mm on L display M12 connector Mounting device included F G 1 green indicator diode / ready 3 yellow indicator diodes / switching outputs Q1, Q2, Q3 Optical axes Transmitter Receiver Reference edge for the measurement (distance zero point) Sight for coarse alignment U L US LIST lectrical connection We reserve the right to make changes ods_19e.fm I 60947... I 60947... IP 67 ccessories: (available separately see page 90) Ready-made cable K- M12-8P-2m-PUR o-operative Target TS 100x100 (reflectivity 50 90%) Leuze electronic GmbH + o. KG Post-box 1111-73277 Owen-Teck Tel. +49 7021 5730 www.leuze.de 74 OSL 30/24-30M-S12-05
OSL 30 Specifications Optical data Measurement range 1) 0.2 30m Resolution 2) 0.1mm/1mm (factory setting) Light source laser Wavelength 650nm (visible red light) Light spot divergent, 6mm at 10m Laser warning notice see remarks rror limits bsolute measurement accuracy 1) ± 5mm (6% diffuse reflection) ± 2mm (90% diffuse reflection) after referencing Repeatability 3) ± 2mm (6 90% diffuse reflection) Temperature drift typ. 0.5mm/K (without referencing) Timing Measurement time 4) 30 100ms (factory setting: 100ms) elay before start-up 1s lectrical data Operating voltage U 10 30V (incl. residual ripple) Residual ripple 15% of U Power consumption 4W Switching outputs PNP transistor, HIGH active (default), NPN transistor or push-pull through configuration Signal voltage high/low (U -2 V)/ 2V Indicators L green continuous light ready no voltage L yellow continuous light object inside teach-in measurement distance object outside teach-in measurement distance Mechanical data Housing metal Optics cover glass Weight 650g onnection type M12 connector, 8-pin nvironmental data mbient temp. (operation/storage) 0 +45 /-40 +70 Protective circuit 5) 2, 3 V safety class 6) II, all-insulated Protection class IP 67 Laser class 2 (acc. to N 60825-1) Standards applied I 60947-5-2 1) Luminosity coefficient 6% 90%, for constant environmental conditions, measurement object 50x50mm² 2) isplay resolution 0.1mm configurable 3) Same object, identical environmental conditions, measurement object 50x50mm² 4) onfigurable, depends on the reflectivity of the object and on the max. detection range 5) 2=polarity reversal protection, 3=short-circuit protection for all outputs 6) Rating voltage 250V Output PNP active high ON OFF Hysteresis Light switching Hysteresis Remarks Measurement time: configurable, depends on the reflectivity of the object and on the measurement mode. Teaching procedure: (factory setting): Position measurement object at the desired measurement distance. pply +U to the teach input. Take teach input back to GN, switching output has now been taught. First edge on line teach Q1/Q2 teaches output Q1, second edge teaches Q2. First edge on line teach Q3 teaches output Q3. uring the teaching of Q1, the yellow L Q1 will flash. uring the teaching of Q2, the yellow L Q2 will flash. uring the teaching of Q3, the yellow L Q3 will flash. ctivation/referencing input: Referencing is carried out by applying the voltage (for a duration of about 300ms). If this process is activated before the measurement, the highest possible accuracy is achieved. The enclosed laser warning signs must be attached to the sensor or in its immediate vicinity such that they are well visible. ON OFF ark switching Lower switching point Upper switching point (teach point) Measurement distance Order guide esignation Part No. With M12 connector OSL 30/24-30M-S12 500 40720 OSL 30/24-30M-S12-05 0706 75
Leuze electronic GmbH + o. KG Post-box 1111-73277 Owen-Teck Tel. +49 7021 5730 OSL 30/24-30M-S12-05 www.leuze.de 76
Rotoscan RO 4 Overview and advantages rotoscan RO4 - Optical area-covering distance sensor with scanner technology - Light source: infrared light laser - Measurement range: 0 50,000mm - etection range: 190 - ngular resolution: 0.36 - Scanning rate: 25 scans/s, 529 measurements per cycle - igital RS 232 or RS 485 interface - 3 PNP switching outputs - Robust metal housing - Protection class IP 65 dvantage 1: rea scanning distance measurement dvantage 2: Reflection-independent distance information dvantage 3: Four switchable detection range pairs dvantage 4: Plug-in LL file for measurement processing on the P dvantage 5: ye-safe laser (laser class 1) dvantage 6: High flexibility due to P-based configuration 77
rotoscan RO-4 Optical distance sensors imensioned drawing 0 50m 24 V The rotoscan RO-4 is an area scanning distance sensor for the detection of objects. The light beam is reflected by a rotating mirror and directed over a semicircular area (190 ) with a radius of max. 50m. The area is divided into two detection areas, each with a radius of 50m. The size of the area to be evaluated can be freely defined in each detection area. It is possible to store 4 detection area pairs in the RO-4 and to switch between these pairs, for example, to define various heights or allowed overhangings. RO-4 with U L approval RO-4-06 with heating and RO-4-08 with heating, dust-insensitive version. Plug-in dll file for measurement processing on the P a Zero point for measurement b Scanning plane R Smallest bending radius = 50mm Measurement principle 190 working range 528 sectors, 0.36 each We reserve the right to make changes ods_10e.fm ccessories: U L US LIST I 60947... I 60947... IP 65 (available separately see page 90) Mounting systems onfiguration software Various connection cables Measurement-LL for P Working field (50m) etection area 1 (max. 50m) etection area 2 (max. 50m) Leuze electronic GmbH + o. KG Post-box 1111-73277 Owen-Teck Tel. +49 7021 5730 www.leuze.de 78 rotoscan RO-4... - 07
rotoscan RO-4 Specifications Optical data Scanning range (per detection area) 0 50m (RO-4-08 25m) ngular range max. 190 ngular resolution 0.36 Scanning rate Transmitter Operating principle 25scans/s or 40ms/scan infrared laser diode (eye safe), wavelength = 905nm beam divergence = 2mrad time base = 100s etection area 1 and 2 Reflectivity from at least 1.8% (matte black) RO-4-08 from 6% (dark grey) Object size > 20mm at distance of 4m > 100mm at distance of 15m Response time at least 40ms (corresponds to 1 scan) Number of detection area pairs 4 (selectable via switching inputs) Output 3x PNP transistor output 24V/250m Measurement value resolution per sector 5mm Repeatability 10 90% diffuse refl. at op. range of 4m ±15mm / ±20mm lectrical data Voltage supply +24V +20%/-30% Overcurrent protection via fuse 2 semi time-lag in the switching cabinet urrent consumption approx. 400m (use 1 power supply), approx. 2 with heating Power consumption < 60W at 24V including the outputs Overvoltage protection overvoltage protection with protected limit stop Mechanical data Housing Weight onnection type nvironmental data mbient temp. (operation/storage) V safety class Protection class IP 65 Laser class 1 (acc. to N 60825-1) Standards applied I 60947-5-2 diecast aluminium, plastic 2.0kg 2 connectors (can be plugged from above, solder connection) -0 +50 /-20 +50-20 +50 /-20 +50 (RO-4-06, RO-4-08) II, all-insulated Transmitted beam Object Tables Remarks "ROsoft" onfiguration Software The configuration software runs under Windows 95/98/ NT/2000/XP and ers the following features: Programming of the detection areas onfiguration of other data Visualisation of the detection area with measurement values isplay of error codes Support of various languages There are various methods with which detection areas can be programmed, for example: "Teach-In" function Numerical and graphical entry of the detection areas "dit" function Received light Order guide esignation Part No. UL RO-4 500 36010 With heating RO-4-06 500 38614 With heating/dust-insensitive RO-4-08 500 41423 etection area 1 etection area 2 urrent measurement values rotoscan RO-4... - 07 0706 79
rotoscan RO 4plus Optical istance Sensors imensioned drawing 0 50m 24 V We reserve the right to make changes RO4_plus_01gb.fm Measurement data transmission via Fast thernet 100Mit/s Measurement data transmission via RS 232/422 serial interface Measurement data reduction, measurement data processing and measurement data filtering in the interface box Service interface for configuring measurement applications and detection fields. With the RO 4plus, it is possible to save and switch between 4 detection fields for object detection. RO 4-08plus with heating, dust-insensitive version. ROplussoft software for configuring measurement applications ROsoft software for configuring detection fields I 60947... I 60947... IP 65 ccessories: (available separately see page 90) Mounting system onfiguration software Various connection cables Measurement principle 190 working range lectrical connection L J M U T S N P R G O 4 3 1 2 4 3 5 1 2 529 measurement sectors, 0.36 each 6 5 4 7 3 8 1 2 Y1 Logic Y2 thernet Y3 Service Y4 RS 232/422 Leuze electronic GmbH + o. KG Post-box 1111-73277 Owen-Teck Tel. +49 7021 5730 www.leuze.de rotoscan RO 4plus... - 03 80
rotoscan RO 4plus Specifications Optical data Scanning range (per detection area) 0 50m (RO 4-08plus 25m) ngular range max. 190 ngular resolution 0.36 Scanning rate Transmitter Object detection Reflectivity Object size Response time Number of detection field pairs Switching inputs Switching outputs Interface assignments 25scans/s or 40ms/scan infrared laser diode (eye safe), wavelength = 905nm beam divergence = 2mrad time base= 100s from min. 1.8% (matte black) RO 4-08plus from 6% (dark grey) > 20mm at distance of 4m > 100mm at distance of 15m at least 40ms (corresponds to 1 scan) 4 (selectable via switching inputs) 4x +24V (FPS1 4 at Y1 for switching between detection fields) additional restart input at Y1 and interface box 4x PNP transistor outputs 24V/250m (larm, Warn, Near field 1, Near field 2) Measurement value resolution per sector 5mm Repeatability 10 90% diffuse refl. at op. range of 4m: ±15mm / ±20mm lectrical data Voltage supply +24V +20% / -30% Overcurrent protection urrent consumption Power consumption Overvoltage protection Mechanical data Housing Weight onnection type nvironmental data mbient temp. (operation/storage) via fuse 2.5 semi-time-lag in the switching cabinet approx. 1 (use power supply with 1.5), approx. 2.5 with heating < 75W at 24V including the outputs overvoltage protection with protected limit stop diecast aluminium, plastic 2.3kg 4 connectors (can be plugged from above) V safety class Protection class IP 65 Laser class 1 (acc. to N 60825-1) Standards applied I 60947-5-2-0 +50 /-20 +50-20 +50 /-20 +50 (RO 4-08plus) II, all-insulated Y1 Logic Y2 thernet Y3 Service Y4 RS 232/422 PIN Function PIN Function PIN Function PIN Function +U 1 Tx+ 1 N 1 TX+ / Tx GN_IN 2 Rx+ 2 Tx 2 Tx- FPS1 3 Tx- 3 GN 3 Rx- G FPS2 4 Rx- 4 Rx 4 Rx+ / Rx J FPS3 5 N 5 GN/shield L FPS4 6 RS 422 detection M Restart_IN 7 N N Near field 1 8 N O Near field 2 P larm R Warn S in T out1 U out2 Tables Remarks The rotoscan RO 4plus is an area scanning distance sensor for the detection of objects. The light beam is reflected by a rotating mirror and directed over a semicircular area (190 ) with a radius of max. 50m. Order guide esignation Part No. RO 4plus 501 06481 With heating/dust-insensitive RO 4-08plus 501 06480 rotoscan RO 4plus... - 03 0706 81
ccessories OS 25 Leuze electronic ccessories OS 25 M12 connectors imensioned drawings K 095-4 K 095-4 K- M12W-4P- K- M12-4P- The following connectors are available for devices with M12 connectors: angled or straight, with and without cable. Protection class (IN 40050) plugged and screwed: IP 67 Selection table M12 connector, user-configurable onnection type Screw terminals K 095-4 Part No. 500 31324 Without cable, 4-pin K 095-4 Part No. 500 31323 M12 connection cable with connector, single-sided Length 2m 5m 10m K- M12W-4P-2m-PV Part No. 501 04543 K- M12W-4P-5m-PV Part No. 501 04545 K- M12W-4P-10m-PV Part No. 501 04547 20m Length 2m 5m 10m K- M12W-4P-2m-PUR Part No. 501 04562 K- M12W-4P-5m-PUR Part No. 501 04564 K- M12W-4P-10m-PUR Part No. 501 04566 PV cable sheath, 4-pin K- M12-4P-2m-PV Part No. 501 04542 K- M12-4P-5m-PV Part No. 501 04544 K- M12-4P-10m-PV Part No. 501 04546 K- M12-4P-20m-PV Part No. 501 04753 PUR cable sheath, 4-pin K- M12-4P-2m-PUR Part No. 501 04561 K- M12-4P-5m-PUR Part No. 501 04563 K- M12-4P-10m-PUR Part No. 501 04565 Leuze electronic GmbH + o. KG Post-box 1111-73277 Owen-Teck Tel. +49 7021 5730 www.leuze.de 82 ccessories OS 25-03
OS 25 imensioned drawings T 25 Mounting systems T 25 (Part No. 500 40269) ccessories UMS 25-12 UMS 25-12 (Part No. 500 40270) Screw IN 912-M4 Slit for clamping sheet metal sheet metal thickness: 1.5to3mm Sensor ccessories OS 25-03 0706 83
ccessories OS 8 Leuze electronic ccessories OSL 8 M12 connectors imensioned drawings K 095-5 K 095-5 K- M12W-5P- K- M12-5P- The following connectors are available for devices with M12 connectors: angled or straight, with and without cable. Protection class (IN 40050) plugged and screwed: IP 67 K- M12-8P- Selection table M12 connector, user-configurable onnection type Screw terminals K 095-5 Part No. 500 20502 Without cable, 5-pin K 095-5 Part No. 500 20501 M12 connection cable with connector, single-sided Length 2m 5m 10m Length 2m 5m Length K- M12W-5P-2m-PV Part No. 501 04556 K- M12W-5P-5m-PV Part No. 501 04558 K- M12W-5P-10m-PV Part No. 501 04560 K- M12W-5P-2m-PUR Part No. 501 04568 K- M12W-5P-5m-PUR Part No. 501 04762 2m 5m PV cable sheath, 5-pin PUR cable sheath, 5-pin PUR cable sheath, 8-pin K- M12-5P-2m-PV Part No. 501 04555 K- M12-5P-5m-PV Part No. 501 04557 K- M12-5P-10m-PV Part No. 501 04559 K- M12-5P-2m-PUR Part No. 501 04567 K- M12-5P-5m-PUR Part No. 501 04569 K- M12-8P-2m-PUR Part No. 501 04591 K- M12-8P-5m-PUR Part No. 501 04590 Leuze electronic GmbH + o. KG Post-box 1111-73277 Owen-Teck Tel. +49 7021 5730 ccessories OS 8-03 www.leuze.de 84
OSL 8 imensioned drawings ontrol guard S 8 (Part No. 500 41067) ccessories S 8 onfiguration adaptor UPG 5 (Part No. 500 39627) UPG 5 onfiguration software P OS 96-PS (Part No. 500 82006) T 8-0 T 8 Mounting systems T 8-0 (Part No. 500 36196) T 8 (Part No. 500 36195) ccessories OS 8-03 0706 85
ccessories OSL 8 Mounting systems UMS 8-10 (Ø10mm, Part No. 500 35020) UMS 8-12 (Ø12mm, Part No. 500 35021) UMS 8-14 (Ø14mm, Part No. 500 35022) imensioned drawings UMS 8- UMS 8.1- UMS 8.1-10 (Ø10mm, Part No. 500 35023) UMS 8.1-12 (Ø12mm, Part No. 500 35024) UMS 8.1-14 (Ø14mm, Part No. 500 35025) lamp Rod Sensor Mount Joint lamp Rod Sensor UMS 8.2-10 (Ø10mm, Part No. 500 35026) UMS 8.2-12 (Ø12mm, Part No. 500 35027) UMS 8.2-14 (Ø14mm, Part No. 500 35028) UMS 8.2- T 8-RH T 8-RH (Part No. 500 35030) Mount Joint lamp Rod Sensor Leuze electronic GmbH + o. KG Post-box 1111-73277 Owen-Teck Tel. +49 7021 5730 ccessories OS 8-03 www.leuze.de 86
OSL 8 imensioned drawings T 8- Mounting systems ccessories T 8-10 (Ø10mm, Part No. 500 35017) T 8-12 (Ø12mm, Part No. 500 35018) T 8-14 (Ø14mm, Part No. 500 35019) lamp Rod diameter Mounting plate Tapped disk Sensor ccessories OS 8-03 0706 87
ccessories OS 96 Leuze electronic ccessories OS 96 M12 connectors imensioned drawings K 095-5 K 095-5 K- M12W-5P- K- M12-5P- For devices with M12 connectors, there are connectors with ready-made cable and 2 connectors with screw connection available. Protection class (IN 40050) plugged and screwed: IP 67 Selection table M12 connector, user-configurable onnection type Screw terminals K 095-5 Part No. 500 20502 Without cable, 5-pin K 095-5 Part No. 500 20501 M12 connection cable with connector, single-sided We reserve the right to make changes ods_96_zu_e.fm Length 2m 5m 10m Length 2m 5m K- M12W-5P-2m-PV Part No. 501 04556 K- M12W-5P-5m-PV Part No. 501 04558 K- M12W-5P-10m-PV Part No. 501 04560 K- M12W-5P-2m-PUR Part No. 501 04568 K- M12W-5P-5m-PUR Part No. 501 04762 PV cable sheath, 5-pin PUR cable sheath, 5-pin K- M12-5P-2m-PV Part No. 501 04555 K- M12-5P-5m-PV Part No. 501 04557 K- M12-5P-10m-PV Part No. 501 04559 K- M12-5P-2m-PUR Part No. 501 04567 K- M12-5P-5m-PUR Part No. 501 04569 Leuze electronic GmbH + o. KG Post-box 1111-73277 Owen-Teck Tel. +49 7021 5730 www.leuze.de 88 ccessories OS 96-04
OS 96 imensioned drawings T 96 UMS 96 Mounting systems T 96 (Part No. 500 25570) ccessories UMS 96 (Part No. 500 26204) for screw M5 onfiguration software P ownload: www.leuze.de onfiguration cable (OS 96 only) K-OS 96-1500 (1.5m, Part No. 500 82007) K-OS 96-6000 (1.5m, Part No. 500 61428) onfiguration adaptor (OS 96) UPG 10 (Part No. 501 07223) ccessories OS 96-04 0706 89
ccessories OS 30 / RO 4 Leuze electronic ccessories OSL 30 M12 connectors OSL 30 imensioned drawings K- M12-8P- Selection table M12 connection cable with connector, single-sided There are 2 connectors available for devices with M12 connectors: angled or straight, with cable. Protection class (IN 40050) plugged and screwed: IP 67 Length 2m 5m PUR cable sheath, 8-pin K- M12-8P-2m-PUR Part No. 501 04591 K- M12-8P-5m-PUR Part No. 501 04590 onfiguration adaptor UPG 5 (Part No. 500 39627) imensioned drawings UPG 5 onfiguration software P OS 96-PS (Part No. 500 82006) o-operative Target TS 100x100 (Part No. 501 04599) For OSL 30 measurement modes with object reflectivity of 50 90%. Specifications Weight: 240g Material: zinc-plated steel Target material: ceramics Target reflectivity: approx. 90% Mounting: screw type TS 100x100 Leuze electronic GmbH + o. KG Post-box 1111-73277 Owen-Teck Tel. +49 7021 5730 ccessories OS 30 / RO 4-04 www.leuze.de 90
RO 4 Selection table RO 4 onnection cable 5m cable length: K-RO4-5000 Part No. 500 38067 10m cable length: K-RO4-10000 Part No. 500 38068 ccessories ables and connectors RO 4 onnection and programming cables as well as freely configurable connectors for the RO 4 are available. Programming cable 3m cable length: K-RO4P-3000 Part No. 500 38069 10m cable length: K-RO4P-10000 Part No. 500 38070 onnectors 15-pin: K-RO4-X1 Part No. 500 38072 9-pin: K-RO4-X2 Part No. 500 38073 imensioned drawing T RO 4 Mounting systems T RO 4 (Part No. 500 38066) Selection table RO 4plus able Y1, 5m cable length: K-014S-5000-14 Part No. 501 06976 onfiguration software P ownload: www.leuze.de able Y1, 10m cable length: K-014S-10000-14 Part No. 501 06977 able Y2, 5m cable length: K T-5000-S Part No. 501 06740 able Y2, 10m cable length: K T-10000-S Part No. 501 06741 able Y3, 5m cable length: K-RO4plus-5000 Part No. 501 06881 able Y3, 10m cable length: K-RO4plus-10000 Part No. 501 06906 able Y4, 5m cable length: K- M12-8P-5m-PUR Part No. 501 04590 able Y4, 10m cable length: K- M12-8P-10m-PUR Part No. 501 06882 ccessories OS 30 / RO 4-04 0706 91
Leuze electronic GmbH + o. KG Post-box 1111-73277 Owen-Teck Tel. +49 7021 5730 ccessories OS 30 / RO 4-04 www.leuze.de 92
Optoelectronic Sensors ubic Series ylindrical Sensors, Mini Sensors, Fibre Optic mplifiers Measuring Sensors Special Sensors Light urtains Forked Sensors ouble Sheet Monitoring, Splice etection ccessories Identification Systems ata Transmission Systems istance Measurement arcode Readers RF-Ient-System Modular Interfacing Units Industrial Image Processing Systems Optical ata Transmission Systems Optical istance Measurement/Positioning Hand-Held Readers Safety Sensors Safety Systems Safety Services Safety Laser Scanners Safety Light urtains Transceiver and Multiple Light eam Safety evices Single-eam Safety evices S-i-Safety Product Range Safety Sensor Technology for PROFIUS P Safety Switches and Safety Locking evices Safety Relays and Safety Interfaces Sensor ccessories and Signal evices Machine Safety Services Leuze electronic GmbH + o. KG In der raike 1 73277 Owen / Germany Phone +49 70 21 / 573-0 Telefax +49 70 21 / 573-199 info@leuze.de www.leuze.de G 195/03-06/07 50104218