Your Performance Partner Seismic Installation for Storage System CONTENTS SSafety Precautions................................. 2 Required Tools..................................... 2 Parts and Fastener List.............................. 2 Installation....................................... -5 Please read and understand these Assembly Instructions before working with or using the. If you need additional information about the, contact Wenger Corporation using the information below. Wenger Corporation 2008 Printed in USA 12/08 Part #259A097-01 Wenger Corporation, 555 Park Drive, P.O. Box 8, Owatonna, Minnesota 55060-08 Questions? Call...USA: (800) 7-09 International (call collect): (507) 55-100
SAFETY PRECAUTIONS This manual contains cautions which are defined as follows. CAUTION: Failure to follow the instruction may result in serious injury or damage to property. Read all of these safety instructions before installing the attic. Make sure that anyone working on the Storage System has read and understands this manual. Failure to comply with Warnings and Cautions in this document can result in damage to property or serious injury. Always observe and comply with the Warnings and Cautions posted on the system equipment. REQUIRED TOOLS The following tools are required to assemble the ; Power Drill with /8" or 9.5 mm Drill Bit Allen Wrench Rubber/Plastic Hammer PARTS AND FASTENER LIST 1 2 Item Qty Description 1 Frame Bracket 2 2 /Cabinet Bracket 6 Screw Insert 6 Machine Screw, 1/-20 x 1 /8" 2
INSTALLATION Installation of the Storage System on New and Existing Cabinets: Note: For Los Angeles, CA installs refer to page 5. 1. Install Storage System as stated in the Assembly Instructions. 2. With securely in place, drill (/8 or 9.5 mm bit) through the remaining clearance holes in floor of all the way through the top of the cabinet underneath. There should be one clearance hole in each corner of the floor. (Detail A) Drill Holes Floor Note: Detail A is shown without the frame and cover to allow for location clarity only. When completing these steps the frame and cover will be assembled. Cabinet Detail A. Use a plastic or rubber mallet to pound the four screw inserts (#) from the inside of the cabinet into the bottom surface of the through the newly drilled hole completed in Step 2.(Detail B). Line up the hole on the Frame Bracket (#1) with the clearance holes located on the floor of the and fit the bracket over the steel tube frame of the. (Detail C) 5. Securely fasten the frame bracket (#1) using the 1/" machine screw (#) making sure the fastener is screwing into the insert below. 6. Complete steps and 5 for the remaining three corners. 1 Drilled Hole Frame 1 Frame Detail C Detail B
INSTALLATION (CONTINUED) Anchoring the and Cabinet to the : 1. The location of the /Cabinet bracket (#2) is to be determined as follows: a. Using the bracket (#2) as a template, place the bracket on the floor of the, 2" side down against the attic floor and the 5" side against the rear attic frame and about -6" in from the side of the cabinet. b. Mark the location of the hole against the attic floor and drill (/8" or 9.5 mm bit) down through the attic floor into the top of the cabinet. Note: If the cabinets are existing: The location of the /Cabinet Bracket (#2) will be governed by the pre-existing location the wall anchor through the back of the cabinet. The bracket cannot interfere with the existing anchor location. The location of the bracket should be just to the right or left of the existing anchor location. 5. Using a rubber or plastic mallet, pound two screw inserts (#) into the newly drilled holes. (Detail D) 6. Position /Cabinet Bracket (#2) on the inside of the cabinet, lining up the slot on the 2" leg with the location of the drilled hole. 7. Attach the /Cabinet Bracket by inserting machine screw (#) from the underside of the top panel and tightening into the screw insert until secure. 8. Anchor cabinet to wall by going through slot located on the 5 leg of the /Cabinet Bracket. Anchor type to be determined by type of wall: (Detail E) a. C.M.U. Bracing Install anchor (X002158) with washer (X00010) going through /Cabinet Bracket, with 5 side of bracket against the back of the cabinet and 2 side b. Wood (2 X 6 ) Bracing Install anchor (X002159) with washer (X00127) going through /Cabinet Bracket, with 5 side of bracket against the back of the cabinet and 2 side c. Metal Stud Bracing Install anchor (X00256) with washer (X00127) going through /Cabinet Bracket, with 5 side of bracket against the back of the cabinet and 2 side Holes Drilled On-Site (for /Cabinet Bracket) Floor Floor 2 Detail D anchor is determined by wall type. See specific instructions per installation type. Detail E
INSTALLATION FOR LOS ANGELES, CA ONLY Installation of the Storage System to Acoustic Cabinets: Due to the length of the threaded rod used for anchoring the AcoustiCabinet to the wall through the wall bracket (255A502), this may need to be cut down to accommodate the Storage System. Installation of the Storage System to Existing Seismic Cabinets: 1. The location of the /Cabinet Bracket (#2) will be governed by the pre-existing location of the wall anchor through the back of the cabinet. An additional anchor location will need to be used for installations into wood and metal studs. The existing location of the wall anchor can be used for C.M.U. wall installations. 2. Type of wall anchoring: a. C.M.U. Bracing Remove the nut and washer located on the threaded rod anchored to the wall. Install the /Cabinet Bracket with 5 side of bracket against the back of the cabinet and 2 side against the top of the cabinet and the existing threaded rod positioned within the slot on the bracket. Replace the washer and nut onto the threaded rod and tighten until secure. b. Wood (2 X 6 ) Bracing Locate the /Cabinet Bracket just to the right or left of the existing wall anchor. Install anchor (X002159) with washer (X00127) going through /Cabinet Bracket, with 5 side of bracket against the back of the cabinet and 2 side against the top of the cabinet. c. Metal Stud Bracing Locate the /Cabinet Bracket just to the right or left of the existing wall anchor. Install anchor (X00256) with washer (X00127) going through /Cabinet Bracket, with 5 side of bracket against the back of the cabinet and 2 side against the top of the cabinet.. With /Cabinet in place, drill (/8 or 9.5 mm bit) up through the hole in the bracket into the top of the cabinet, through the floor of the attic.. Use a plastic mallet to pound screw insert (#) into floor of attic at newly drilled location. 5. Complete attachment of /Cabinet Bracket by inserting machine screw (#) from the under side of the top panel and tightening into the screw insert until secure. New and Cabinet Installations: 1 The location of the /Cabinet Bracket (#2) to be determined as follows: a. Using the bracket (#2) as a template, place the bracket on the floor of the, 2 side down against the attic floor and the 5 side against the rear attic frame and about -6 in from the side of the cabinet. b. Mark location of hole against the attic floor and drill (/8 or 9.5 mm bit) down through the attic floor into the top of the cabinet. 2. Use a plastic mallet to pound screw insert (#) into floor of attic at newly drilled location.. Position /Cabinet Bracket on the inside of the cabinet, lining up the slot on the 2 leg with the location of the drilled hole.. Attach the /Cabinet Bracket by inserting machine screw (#) from the underside of the top panel and tightening into the screw insert until secure. 5. Anchor cabinet to wall by going through slot located on the 5 leg of the /Cabinet Bracket. Anchor type to be determined by type of wall: a. C.M.U. Bracing Install anchor (X00118) into screen (X00117) and epoxy (RM11652) going through /Cabinet Bracket, with 5 side of bracket against the back of the cabinet and 2 side b. Wood (2 X 6 ) Bracing Install anchor (X002159) with washer (X00127) going through /Cabinet Bracket, with 5 side of bracket against the back of the cabinet and 2 side against the top of the cabinet. c. Metal Stud Bracing Install anchor (X00256) with washer (X00127) going through /Cabinet Bracket, with 5 side of bracket against the back of the cabinet and 2 side against the top of the cabinet. 5