AMPTRAC TM CONNECTIVITY MANAGEMENT SYSTEM

AMP NETCONNECT TM AMPTRAC TM CONNECTIVITY MANAGEMENT SYSTEM The AMPTRAC Connectivity Management System turns cabling systems and their connected devices into intelligent networks by reducing costly and time-consuming manual cable management. With this system, you can track and document all moves, adds and changes to your network from a centralized location as they occur. This fully automated system optimizes asset utilization, maintains accurate documentation and helps prevent costly errors. The AMPTRAC Connectivity Management System s easy-to-implement hardware coupled with itracs cutting-edge software can be integrated into new or existing network. By allowing you to proactively respond to any changes in connectivity through customizable alerts or alarms, the itracs software optimizes your network monitoring and security. AMPTRAC hardware when used in conjunction with itracs software provides the missing link that integrates network management and physical layer management revolutionizing the way networks are controlled and documented. This one-of-a-kind infrastructure management system automatically generates a complete physical topology of your network at the Telecommunications Room/Data Center, while helping you manage and trouble shoot the network remotely. SYSTEM FEATURES & BENEFITS :: Reduces downtime and response time :: Integrates network and physical layer management :: Helps to increase productivity :: Reduces operating costs :: Improves port and asset utilization :: Provides accurate and timely information :: Improves service levels :: Supports Cat 5e, Cat 6 and fiber optic networks :: Analyzers sized for enterprise and branch locations

COMPONENTS Enterprise Analyzers Size Ports Channels Part Monitored Monitored** Figure Type Number Stand-Alone 1435370-1 1U (1.75") 256 128 A Master 1435370-2 Link 1435370-3 Stand-Alone 1435371-1* 6U* (10.50") 512-1,536 256-768 B Master 1435371-2* Link 1435371-3* Expansion Card 256 128 C - 1435372-1 Link to Master Analyzer Cable, Non-Plenum D - 1435338-X X denotes length in feet: -4 = 4, -7 = 7, 2- -5 = 25, 5- -0 = 50 Note: The I/O interface for the Enterprise Analyzers is an AMPMODU connector. * The 6U Analyzer comes equipped with 2 cards (480 ports). The 6U Analyzer can hold up to six (6) cards total. Each card is capable of monitoring 256 ports. Additional Expansion Cards for the 6U Analyzer are ordered separately. ** The complete channel connection to a work area outlet passes through two monitored ports, the network equipment (switch) and the patch panel. Therefore, the number of channels is half the number of ports monitored. B A :: Available in Stand-Alone, Master and Link versions :: Available in 1U (1.75") and 6U (10.50") rack sizes :: 1U versions can monitor up to 256-ports :: 6U versions come equipped to monitor up to 512- ports and can be modified via expansion slots (6U analyzer contains 4 expansion slots) to monitor up to 1536-ports. :: Expansion Boards can monitor up to 256-ports each and are used with expansion slots in the 6U Analyzers :: The maximum number of analyzers that can be connected concurrently to the same database via TCP/IP is 1,024 Stand-Alone Analyzers: :: Used by themselves and do not directly attach to other Analyzers (Master or Link) :: Connect to the database software through a 10BASE- T LAN connection via standard TCP/IP Master Analyzers: :: Connect with up to nine other Link Analyzers (either 1U, 6U or a combination of both) :: Connect to the database software through a 10BASE-T LAN connection via standard TCP/IP :: Will not connect directly with other Master or Stand-Alone Analyzers Link Analyzers: :: Expand Master Analyzer's port capacity :: Must always be connected with a Master Analyzer (either a 1U or 6U version) :: Maximum distance between Master and Link Analyzer is 50 feet C D

Branch (Mini) Analyzer Description Power Cord Option Part Number US Version 1591304-1 Branch (Mini) European Version 1591304-2 Analyzer Australian Version 1591304-6 UK Version 1591304-7 Note: The I/O interface for Branch Analyzers is a DB25 connector. Front :: Provides 128 analyzer ports via five (5) DB25 connectors and one (1) RJ-45 :: Provides 2 relay outputs for control of external equipment :: Provides additional expansion for relays, sensors, and other functions via a RS-485 bus to a planned future expansion unit. :: Local analyzer management provided via a computer or PDA attached to the local terminal (console) port. :: Remote analyzer management provides via a Telnet session. :: Available with different local power cord options :: Suitable for shelve or 19" rack mounting (1U high) Analyzer I/O Cable Assemblies Back Analyzer Monitored Device Connector Type Application Number of Conductors Fig. Part Number AMPTRAC Patch Panels None, used for IDC Cat 5e, Cat 6 and MT-RJ 24 A 1435488-X Flex-strip Sensor 1.27 mm, FFC LAN Switches & Retrofit Patch Panels 24 D 1435374-Y Cassettes 6-Position, RJ-11 MT-RJ and MRJ 21 6 B 1435621-Y Duplex SC LAN Switches 6-Position, 2.54 MTE Duplex SC Adapter plates, cassettes 6-1435686-Y Enterprise I/O Interface 24 C 1435336-Y AMPMODU 16-1777000-Y PCB Sensors 2.0mm, AMPMODU LAN Switches 12-1435957-Y 8-1435938-Y 6-1777001-Y 2-1435843-Y AMPTRAC Patch Panels None, used for IDC Cat 5e, Cat 6 MT-RJ 24-1435844-X Branch (Mini) I/O Interface DB25 Flex-strip Sensor 1.27 mm, FFC LAN Switches Retrofit Patch Panels 24 E 1435846-Y PCB Sensor 2.0 mm LAN Switches 24-1435845-Y X denotes length in feet: -7=7, 1- -4=14, 5- -0=50, 9- -9=100 (Note: Can be cut to length) Y denotes length in feet: -4=4, -7=7, 1- -0=10, 1- -4=14, 2- -5=25, 5- -0=50, 7- -5=75, 9- -9=100 A B :: The I/O cable is used to connect the device (patch panel or switch) being monitored to the analyzer. Selection of right I/O cable depends upon the analyzer being used (Enterprise or Branch), the I/O interface on the monitored device and also the length... AMPTRAC Cat 6 and 5e UTP and MT-RJ patch panels use an IDC connection to the sensor contact and therefore the I/O cable is unterminated on one end and can be cut to the appropriate length. Available for the Enterprise and Branch Analyzer. One I/O cable required per 24-port patch panel, and two for 48-port patch panel... AMPTRAC Connectivity Management System uses flexible sensors strips for some LAN switches and also for patch panel retrofit applications. The flexible sensor strip uses the 1.27 mm FFC (flexible flat circuit) connector. Available for use with the Enterprise and Branch analyzer... AMPTRAC Connectivity Management System uses PCB sensor strips for many LAN switches. The PCB sensor strip is equipped with a 2.0mm MODU. Available for use with the Enterprise and Branch analyzer... AMPTRAC Connectivity Management System offers the MT- RJ/MPO cassette and the Mini-RJ21 cassette with a plug-andplay 6-position modular plug (RJ11) interface C E... AMPTRAC Connectivity Management System offers the Duplex SC adapter plates, the Duplex SC/MPO cassettes and some PCB sensors (switch uplink ports) with the 6-position 2.54 mm MTE... All 24-conductor I/O cables come with molded boots on both ends... All I/O cables come with molded boots on the analyzer connector end... I/O cable is CM rated and listed D

Twisted Pair Patch Panels Type Ports per Module Total Ports Rack Units Part Number Standard 6 24 1U (1.75") 1435326-1 (Flush) 48 2U (3.50") 1435327-1 Category 6 6 24 1U (1.75") 1435622-1 48 2U (3.50") 1435623-1 Angled 4 24 1U (1.75") 1435631-1 48 2U (3.50") 1435632-1 4 24 1U (1.75") 1435658-1 (Y-G-Or-Bl) 48 2U (3.50") 1435659-1 Standard 6 24 1U (1.75") 1435367-1 (Flush) 48 2U (3.50") 1435368-1 Category 5e 6 24 1U (1.75") 1435624-1 48 2U (3.50") 1435625-1 Angled 4 24 1U (1.75") 1435633-1 48 2U (3.50") 1435634-1 4 24 1U (1.75") 1435660-1 (Y-G-Or-Bl) 48 2U (3.50") 1435661-1 SL Series Multimedia 24 1U (1.75") 1435784-1 Angled 6 (Unloaded) 48 2U (3.50") 1435785-1 :: Incorporate integrated solid contacts with the panel for enhanced protection, appearance and reliability :: I/O connection made via 110 IDC punch down in the rear of patch panel, minimizing pre-planning and allowing for cables to be cut to length. :: Cost-effective solution for AMPTRAC Connectivity Management-ready solution - install AMPTRAC patch panels now and analyzer and software later. :: Available in standard flush versions as well as angled versions for improved cable and space management. :: Uses AMP NETCONNECT high-performance SL Series Cat 6 and 5E110Connect modular jacks. :: SL Series Multimedia Patch Panels come unloaded and accept SL Series Jacks for custom configurations Terminated Shielded Patch Panels Description Total Ports Part Number Category 6 Shielded, AMPTRAC Ready 24 1644042-2 Category 6 Shielded, AMPTRAC Enabled 24 1644042-1 AMPTRAC Upgrade Kit 24 1711148-1 :: Category 6 Shielded Patch Panel, 10 Gigabit Ready :: AMPTRAC Enabled and Upgrade Kits incorporate fully integrated solid contacts for enhanced protection, appearance and reliability :: AMPTRAC Ready version easily and cost-effectively upgraded to AMPTRAC Enabled with Upgrade Kit :: AMPTRAC Enabled version fully equipped to support the AMPTRAC System :: Utilizes 2.0mm I/O connection in the rear of the panel Upgrade Kit AMPTRAC Enabled Patch Panel

Fiber Optic Patch Panels Description I/O Rack Part Interface Type Capacity Units Figure Number IDC Drawer 24-port (48-Fiber) Jacks sold separately 1U A 1435329-1* Enclosure 72-port (144-Fiber) Jacks sold separately 4U - 1435788-1* Drawer 4 AMPTRAC MT-RJ Cassettes (cassettes sold separately) 1U - 1435608-1 AMPTRAC MT-RJ 6-Position Enclosure 12 AMPTRAC MT-RJ Cassettes (cassettes sold separately) 4U B 1435593-2 Mod Plug 6-ports (12-Fibers) XG (850nm LO 50µm) Multimode - C 1435594-2 (RJ11) MPO Cassettes 6-ports (12-Fibers) 62.5µm Multimode - C 1435672-2 6-ports (12-Fiber) Singlemode - C 1435673-2 6-port (12-Fiber) Multimode (Beige) - D 1435657-1 6-Position Snap-In Adapter Plate 6-port (12-Fiber) Singlemode (Blue) - - 1435657-2 2.54 MTE 6-port (12-Fiber) Singlemode APC (Gr.) MODU - E 1435657-3 AMPTRAC Duplex SC Retrofit Kit For existing 6-port adapter plate (559596-X) - - 1435685-1 6-Position 6-ports (12-Fibers) XG (850nm LO 50µm) Multimode - - 1435688-2 Mod Plug MPO Cassettes 6-ports (12-Fibers) 62.5µm Multimode - F 1435653-2 (RJ11) 6-ports (12-Fiber) Singlemode - - 1435689-2 *Note: AMPTRAC MT-RJ Patch Panel Enclosures come loaded with empty MT-RJ 6-Pack Housings. MT-RJ Patch Panel Jacks purchased separately. See page 122. A Loaded and Terminated :: Available for MT-RJ and Duplex SC systems :: AMPTRAC Duplex SC Connector uses standard AMP NETCONNECT Enclosures :: Available in 62.5µm, XG (850nm LO 50µm) and Singlemode :: Available for MPO cassettes... Contact an AMP NETCONNECT Product Sales Representative concerning the latest AMPTRAC data center products, such as MT-RJ, SC and LC fiber cassettes, MRJ 21 copper cassettes and AMPTRAC compatible active products B C E D F

UTP Patch Cords Description Color Part Number White 1435834-X Gray 1435835-X Green 1435860-X AMPTRAC Blue 1435861-X Category 6 Red 1435862-X Yellow 1435863-X Black 1435864-X Orange 1435918-X Violet 1435919-X Cross-over (Category 6) Red with black boots 1435953-X X denotes length in feet: -3 = 3, -5 = 5, -7 = 7, 1- -0 = 10, 1- -4 = 14, 1- -6 = 16, 2- -5 = 25 :: Exceeds Cat 5e and Cat 6 performance specifications :: Patch cable assemblies contain 9 th conductor that is connected to external probe molded into the modular plug boot :: AMPTRAC Category 6 patch cable assemblies are backwardly compatible so that they support new or existing Category 5e systems exceed Cat 5e channel requirements :: External probe makes contact with sensor pad on the sensor strip and/or patch panel sensor contact :: Off-center probe designed to accommodate stackedjack LAN switch configurations :: CM rated and listed cable :: Universal wiring (T568A/T568B) :: Color matched overmolded boots :: Ethernet cross-over cable assemblies available Fiber Patch Cords Description Fiber Type Figure Part Number 62.5µm Multimode 1435351-X MT-RJ to MT-RJ XG (850nm LO 50µm) Multimode 1435352-X Singlemode A 1435353-X 62.5µm Multimode 1435355-X MT-RJ to Duplex SC XG (850nm LO 50µm) Multimode 1435356-X Singlemode 1435357-X 62.5µm Multimode 1435792-X MT-RJ to Duplex LC XG (850nm LO 50µm) Multimode 1435793-X Singlemode 1435794-X 62.5µm Multimode 1435724-X Duplex SC to Duplex SC XG (850nm LO 50µm) Multimode 1435725-X Singlemode B 1435726-X 62.5µm Multimode 1435795-X Duplex SC to Duplex LC XG (850nm LO 50µm) Multimode 1435796-X Singlemode 1435797-X 62.5µm Multimode 1435789-X Duplex LC to Duplex LC XG (850nm LO 50µm) Multimode C 1435790-X Singlemode 1435791-X X denotes length in meters: -1 = 1, -2 = 2, -3 = 3, -5 = 5, -7 = 7, 1- -0 = 10 Note: Contact Tyco Electronics concerning potential ST connector solutions. :: Exceeds optical performance specifications for 62.5 micron, 50 micron (OM-3) and singlemode :: Duplex SC, MT-RJ and Duplex LC assemblies available :: Patch cable assemblies contain copper conductor that is connected to external probe :: External probe makes contact with sensor pad on the sensor strip and/or patch panel sensor contact. :: One wire/one probe design to monitor duplex fiber port as a single connection :: OFNR riser rated and listed cable :: Cable is a mini-tri-zip design for flexibility and small size A B C

Patch Panel Retrofit Kits Description Part Number AMP NETCONNECT Cat 5e, 24-port 1435360-1 AMP NETCONNECT Cat 6, 24-port 1435363-1 :: Each kit contains a sensor strip, four front bezels and a connector retaining clip :: Kit is designed to retrofit the AMPTRAC system solution to an existing installation of AMP NETCONNECT Cat 5e or Cat 6 patch panels :: Each kit contains material to retrofit 24 ports Two kits are required for a 48-port patch panel :: Uses 1.27mm FFC for I/O interface LAN Electronic Sensor Strips Type I/O # Ports Part Interface per sensor Number Typical Switch 26 1435827-1 CISCO 2950 24 1777005-1 Alcatel OmniSwitch OS6600-24 24 1435346-5 CISCO 3500, 24-port 24 1435346-4 CISCO 3500, 48-port 24 1435346-1 Cisco 4000 and 6000 48-port blades 2.0 mm 24 1435939-1 Nortel Baystack 470-48T, 48-port PCB MODU 24 1435937-1 CISCO MT-RJ 6000 Blade, 24-port Sensor Strip 24 1435933-1 Nortel Baystack 450-24T, 24-port 16 1435927-1 Extreme Summit48i, 48-port 16 1435820-1 CISCO 16-port GBIC blade 12 1435952-1 Extreme Summit1i, Summit5i and Alpine 3808 6-position 2.54 mm 2 1435819-1 CISCO 6550 Fiber Supervisory Blade MTE 2 1435818-1 CISCO 3500 Fiber Uplink Ports Description I/O Cable Retainer Bracket for CISCO 3500, 48-port switch 1435779-1 Part Number :: Sensor Strips are readily available for a number of LAN electronic equipment types :: Custom Sensor Strips can be designed to work with most LAN electronic equipment. For assistance, call AMP NETCONNECT Customer Service at 1-800-553-0938 :: LAN equipment manufacturer, model number, and model revision are required in determining the selection of the proper sensor strip :: Sensor strips contain an adhesive backing for easy installation Sensor Strips Cable Retainer Bracket

ITRACS Software At the core of the AMPTRAC Connectivity Management System is the itracs sophisticated database application that discovers, maps, documents, and reports the status of your network assets from endto-end. When combined with AMPTRAC hardware, this integrated set provides real-time monitoring of the network and all devices, including PCs switches, hubs, servers, cabling and connections. The stateof-the-art software features a sophisticated graphics module and a variety of customizable, userdefined tracking and reporting options. The itracs solution also gives you the ability to set up alerts, alarms, audit logs and messages, all according to pre-defined policies and rules. The itracs solution offers a variety of optional add-on products that enhance and extend itracs physical layer connectivity capabilities to end device, as well as to third- party and in-house applications. These products include itracs IDISCOVER, itracs IPBX, itracs Virtual Wiring Closet, and itracs SDK. itracs Enterprise Adapters for HP Openview, CA Unicenter, IBM Tivoli, Peregrine and other leading third-party as well as in-house applications are also available. For information about product availability, pricing, delivery, installation and support services, and other software-related questions, please contact itracs Corp. at 1-877-948-7227, by e-mail at sales@itracs.com.www.itracs.com, or visit them at www.itracs.com AMP, AMP NETCONNECT, AMPMODU, AMPTRAC, NETCONNECT and Tyco are trademarks. itracs is a trademark of itracs Corporation. Nortel is a trademark of Nortel Networks Limited. Cisco is a trademark of Cisco Systems, Inc. Other products, logos, and company names mentioned herein may be trademarks of their respective owners. 1309354-5M-TE-TE-9/04 In the U.S. 1-800-553-0938 Canada 905-475-6222 Mexico 525-729-0400 South and Central Americas 54-11-4733-2200 www.ampnetconnect.com e-mail: networking.help@tycoelectronics.com Copyright 2004 Tyco Electronics Corporation. All rights reserved. Printed in USA Tyco Electronics reserves the right to change part numbers and discontinue parts without notice.