Ruby SuperSystem Bulletin Hardware & Software Support Services Bulletin NO: 08.00 Subject: Products: Publication Date: Author: Wayne Board All Wayne Ruby SuperSystem Installations Utilizing DCPT s January 22, 8 Dave Watlington Wayne and VeriFone have completed development and testing of an improved solution to interface the VeriFone Ruby SuperSystem POS with Wayne DCPTs/s and the MSM (for debit). The new solution, which is know as the Wayne Standard Interface Board, provides the following benefits: ¾ Replaces the B&B RS232/48 converter, providing superior protection against power spikes with onboard circuitry and manages signal loading on the communication lines. ¾ The standard I/F Board will be installed in the Wayne Electronic Central. This provides for a central point of connection for all Wayne equipment and follows standard wiring and connection practices used for all Wayne dispenser/ interfaces. ¾ Spreads the connections over four (4) RS48 channels, thus providing more robust communications and allowing the ability to isolate individual channels for troubleshooting and diagnostics. ¾ Supports a diagnostics port, which allows data monitoring and capture of data communication traffic, also provides ability for future enhancements such as direct command level diagnostics. ¾ Easy to view status indicators giving an "at a glance" status on data communication. Note: The B&B converter will no longer be required when using the Wayne board however, the following adapter from VeriFone is required to connect the RS232 interface cable to the board/electronic Central cabinet via the DB2F connector. PART NUMBER DESCRIPTION 342-0 Adapter, DB2M (Adapter, Black) Page of 7
Upgrade Kit A Upgrade Kit may be purchase from Wayne or individual parts as indicated below: PART NUMBER DESCRIPTION 882-00 Upgrade Kit Includes all necessary components 884288-00 PCB Assembly, 4 Channel Interface Board 802-002 Plate Assembly, Electronic Central Cabinet for Interfacing 882 Cable Assembly, Control Board to DB2F/Connector Plate 882-00 Documentation, Installation Instructions 88240-00 Cable Assembly, MSM, 30 Inch Used For Diagnostics Only! Note: Should be installed and left in the EC cabinet. The Upgrade Kit includes the I/F board, EC side plate replacement, interconnect cables, diagnostic cable, and documentation. The documentation covers installation and jumper settings for the VeriFone Ruby SuperSystem. Also, available is a combination kit that includes the PIB Installation Kit and the Installation Kit. Contact your local Wayne Distributor for details concerning this option. Ruby New base Application Requirements All boards that are installed with VeriFone Ruby SuperSystems utilizing its New base applications will NOT need to be re-jumpered (JP & JP2) for the RTS communications parameter. The default board configuration will suffice when installing with a Ruby SuperSystem Newbase applications. Note: New base applications may be identified by the presence of the Maintenance menu in the application while at the switcher mode. Ruby Old base Application Requirements All boards that are installed with VeriFone Ruby SuperSystems utilizing its Old base applications WILL need to be re-jumpered (JP & JP2) for the Auto enable communications parameter. Refer to the installation drawings in the following pages. VeriFone RS232 Input Utilizing Auto Enable Jumper Position Description JP OFF Disable external TXEN Line JP2 ON Auto Enable for output channels Terminating Communication Wires Communication wires from each of the s will now be terminated utilizing the terminal strip (TB) at the bottom of the EC cabinet. A maximum of six () s are allowed per channel as indicated in the drawing Channel Definitions. Refer to Page. Page 2 of 7
Jumper Definitions and Default Settings for Interface PCB Assy 884288-00 REV. 2 Bold type and * = Factory Default Jumper Position Description JP ON Enables 48 XMIT, RS232 TX must be disabled (NO jumper on JP3) OFF * Disables 48 XMIT, when using RS232 communications JP2, JP27,JP28 &2 * Diagnostics channel, Receive only 2&3 Diagnostics channel, Transmit and Receive Echo must be enabled to use Wayne Diagnostic Software (JP-JP4) JP3 &2 * Enables RS232 XMIT NON-Inverted Mode 2&3 Enables RS232 XMIT Inverted Mode JP4 &2 * RS232 Receive NON-Inverted Mode 2&3 RS232 Receive Inverted Mode JP &2 XMIT Enable (TXEN) NON-Inverted Mode 2&3 * XMIT Enable (TXEN) Inverted Mode JP &2 * XMIT Enable (TXEN) Driven by RS232 RTS (JP7=&2 for RS232) 2&3 XMIT Enable (TXEN) Driven by RS232 DTR (JP7=&2 for RS232) JP7 &2 * TXEN Driven by RS232 RTS or DTR 2&3 TXEN, RS48 operation JP8 ON K-ohm Pull-Up on RS48+ line (Master Mode) JP must be ON OFF * RS48+ (Slave Mode). JP must be OFF and JP0=ON JP ON K-ohm Pull-Down on RS48- line (Master Mode) JP8 must be ON OFF * RS48- (Slave Mode). JP8 must be OFF and JP0=ON JP0 ON * RS48, Slave Mode. JP8 & JP should NOT be installed OFF RS48, Master Mode. JP8 & JP should be installed JP,JP2,JP3,JP4 &2 * Echo Mode OFF for channels,2,3 & 4 respectively 2&3 Echo Mode ON for channels,2,3 & 4 respectively JP,JP,JP7 &2 * Normal Channel operation 2&3 RS48 Channel Diagnostics JP8,JP,JP20 &2 * Normal Channel 2 operation 2&3 RS48 Channel 2 Diagnostics JP2,JP22,JP23 &2 * Normal Channel 3 operation 2&3 RS48 Channel 3 Diagnostics JP24,JP2,JP2 &2 * Normal Channel 4 operation 2&3 RS48 Channel 4 Diagnostics JP27 and JP28 see above (jp2) JP2 ON Auto TX-Enable (NO TXEN handshake line needed) for channels thru 4 OFF * Standard TX-Enable (TXEN handshake line required) JP30 &2 * Standard TX-Enable for RS48 Input (TX48EN Signal Required) 2&3 Auto TX-Enable for RS48 Input (TX48EN Signal NOT Required) JP3 &2 * Echo mode OFF for RS48 Input Driver 2&3 Echo mode ON for RS48 Input Driver Page 3 of 7
Board Jumper Layout & Definitions 22 P ON : K Pull-UP on RS48 + Line (Master mode & JP =ON) OFF : RS48+, slave mode, JP=OFF, JP0=ON 2 ON : K Pull-DOWN on RS48 - Line (Master mode & JP8 =ON) OFF : RS48-, slave mode, JP8=OFF, JP0=ON 2 ON : RS48, slave mode (JP8 & JP should not be installed) OFF : RS48, master mode (JP8 & JP should be installed) 2 ON : enable RS48 TX (must disable RS232: JP3 must be OPEN) OFF : disable RS48 TX (when using RS232 mode) 2 JP2 P2 2 U2 CH 4 JP4 JP30 JP3-2 Enables RS232 TX non-inverted mode 2-3 Enables RS232 TX inverted mode -2 TXenable driven by RS232 RTS (JP7-2) 2-3 TXenable driven by RS232 DTR (JP7-2) -2 TXenable driven by RS232 RTS or DTR 2-3 TXenable driven by RS48 controller ON = use AUTO TX-EN OFF = TXEN handshake line available U CH 3-2 TX-EN provided by 3rd Party Line 2-3 Auto TX-Enable provided by 884288 bd -2 Echo Mode OFF for RS48 Driver 2-3 Echo Mode ON for RS48 Input Driver -2 RS232 RX non-inverted mode 2-3 RS232 RX inverted mode -2 TXenable non-inverted mode 2-3 TXenable inverted mode JP3 U0 CH 2 JP2 884288 4 to Channel Std Interface Board for 3rd Party Use (NOT TO SCALE) U CH JP8 JP JP0 JP JP3 JP4 JP JP JP7 JP REC4 DS7 REC3 DS REC2 DS REC DS4 TXEN DS3 MREC DS2 TX DS J3 J4 JP JP JP7 JP8 JP JP20 JP2 JP22 JP23 JP24 JP2 JP2 YLW Green red CHAN4 CHAN3 CHAN2 CHAN s TB : 3&4 s TB : &0 s TB : & s TB : &2 3rd party control line Wayne answer 3rd party poll 88240-xxx RIBBON CABLE TO DIAGNOSTIC LAPTOP (COM-PORT) 882-xxx RIBBON CABLE TO 3RD PARTY CONTROLLER s TB : &2 s TB : & s TB : &0 s TB : 3&4 22 DIAGNOSTICS -2 LISTEN 2-3 TALK -2 LISTEN 2-3 TALK -2 LISTEN 2-3 TALK JP2 JP27 JP28 DBEN DS0 DBRX DS DBTX DS8 yellow red Page 4 of 7
Channel Definitions J7 Wayne EC standard pin outs for Power Supply (J7) Pump Current Loops RS48 channels board locations slot slot2 slot3 slot4,, or 7 Companion bd 82024 2400 bd 820220 Std IF bd 884288 882 Ribbon Cable PIB board 8334 800 Ribbon Cable TB 2 TB 3 TB 4 TB CH pump current loop CH 2 pump current loop 2 3+ 4-7+ 8-0 2 3 4 7 8 0 2 3 4 7 8 0 + 2-3 4 + - 7 8 + 0- CH RS48 CH 2 RS48 CH 3 RS48 802 Cable-Plate 2 2 2 2 3 4 3 4 3 4 3+ 4- CH 4 RS48 Wayne Pumps 0-24 via Data Distribution Box ecpinbds.vsd Wayne s 0-24 Page of 7
Companion board (slot ) D2400 board (slot 2) PIB board (slot 4,, or 7) Upgrade Procedures Wayne Standard Interface upgrade (VeriFone) KIT 882-00, Board 884288, cable 882 ) Turn off power to the EC 2) Remove B&B converter from VeriFone Ruby cable 3) Install Wayne std I/F bd (pn 884288) into slot#3 4) Evenly distribute Wayne lines on TB s to one channel (MAX) Wayne EC rs48/rs232 b&b converter VeriFone POS Note: Previous interfacing method utilizing the B&B conveter. Wayne EC Wayne s Companion board (slot ) D2400 board (slot 2) std I/F board (slot 3) PIB board (slot 4,, or 7) TB Cable-Plate 882 new cable Wayne s ) Connect VeriFone cable direct to cable-plate ) Power up Wayne EC 7) pn:884288 LEDs should start blinking Red DS = VeriFone polling Wayne s Green DS2 = Wayne s answering poll Yellow DS3 = Transmit enable (control line) 8) IF the LEDs do not work THEN power down the EC remove the 884288 board return wiring to original configuration re-install B&B converter ) Power up Wayne EC VeriFone POS TB# + 2- cats 0-0 typical cats 07-2 typical Wayne s Wayne s Wayne s & MSM usually connects here 0 3 4 cats 3-8 typical cats -24 typical & MSM Page of 7
Note: This bulletin is developed by the Hardware & Software Support Services of VeriFone and should be filed in the Ruby SuperSystem Service Manual in the Bulletin section along with its accompanying List of Bulletin s index. All ISDevelopment Bulletins distributed should be filed accordingly with that group of bulletins. This bulletin should be distributed to all technical personnel in your organization. Failure to do so may result in additional service charges incurred by your service organization. If you have any questions concerning this bulletin please contact the VeriFone Technical Services Support Center at: -800--77. Page 7 of 7