Heating, cooling and irrigation system for a house. Control with two controllers TS-T + depending on the seasons. option R, R, R, R4, R, R6, R7 - Heat pump. Sx - nsors. F - Thermal cutoff. B - Electric heater. Non-return valve. In order not to complicate the functional circuit are not shown: - fety valves - Expansion tanks - Filters - Shut-off valves - Cranes filling - Cranes for emptying V - Three-way manual valve. Functional scheme V - Three-way solenoid valve А9 - Solar collector(s) - nsor for measuring air temperature А- Water heater V R4 R B V А - swimming pool Sg К А7 - Boiler А - convector К К4 К А8 - Fireplace К6 К7 Sh А - jacuzzi R К R7 R R R6 The coils in the pool and jacuzzi are set arbitrarily. In practice it is more efficient use of aluminum radiators. А - Garden Pump А - water sprinklers for watering lawns. А - hydrophore pump. Can be used outdoor or hydrophore pump. А4 - Draw-well А - solenoid valve
Heating circuits: G. Collector - tank 9, V,, R4. G. Collector - pool 9, V, V,, R4 Manual switching V for change the round. Collector - Jacuzzi 9, V, V,, R4. Upper heating circuits must be filled with low-freezing fluid (antifreeze). The fluid must have a freezing point suitable for the geographical area. G. heating of tank with an electric heater. Lower circles are filled with water. G4. Fireplace - tank 8, А, R, K7. G. Fireplace - convectors 8, K,, R, K6. G6. Boiler - tank 7, А, R, K4. G7. Boiler - convectors 7, K,, R, K. G8. Boiler - jacuzzi 7, R6, K. Cooling circuit: G9. Draw-well - convectors, R7, K. Irrigation circle: G. Draw-well - garden pump 4, А, or Draw-well - hydrophore pump 4, А,,. Each of the circles G to G is managed independently and can be turned on or off by management. This allows sequential construction and inclusion of the rounds in operation. Disabling it by establishing the numbers of sensors from that round to zero. The inclusion of a circle becomes, by establishing the real numbers of the sensors. The time required for inclusion or exclusion is not more than 6 seconds. ttachment of the circles to the controller's output is indicated in the following table: Controller TS-T+ number: utput Round number: number: G 4 G G G6 G7 G4 G G 4 G8 G9
Electric scheme controller TS-Т+ number utputs: А V C 4 nsors S,S,S,S и S6 S S S S S6 4 6 7 8 9 4 6 49 48 47 46 4 44 4 Fuse Sg R4 R R Fan convectors V C F Fuse ll metal housings to be connected to earth! Contactor V C L Фаза N Нула B Electric heater utput of the controller number is used as a weekly temperature timer. utputs: А V C Electric scheme controller TS-Т+ number 4 nsors S,S,S,S и S6 S S S S S6 4 6 7 8 9 4 6 49 48 47 46 4 44 4 Sh Fuse R R6 R7 Connect only one (). V C А - Електромагнитен вентил А - Градинска помпа R Fan convectors utput of the controller number is used as a weekly temperature timer.
Tables for programming the controllers and : Row from the table for programming Top Level - C Top level thermostats ХХ= до 9 C Top Level-nsor nsor for thermostat top level S=-6 Low Level - C Low level thermostats ХХ= до 9 C Low Level-nsor nsor for thermostat top level S=-6 N TEMPERTURE - 9 C FF TEMPERTURE - 9 C sensor ST - 6 sensor SP - 6 Used logical function ND, R Table setup of the differential regulators, logical functions and thermostats. controller number utput number G G G G6 G7 4 9 4 4 9 6 controlled round 6 6 8 6 А 6 Note Temperature to TURN N Temperature to TURN N ST-SP to TURN N ST-SP to TURN FF nsor heat source nsory hot-receiver А(ND) / О(R) In the summer should be set - to prohibit the filing of heat from the boiler to the convectors. - Do not put ST = SP! Programming:. t the time and date.. t the timer program if necessary.. Program the top table in the controller. 4. Perform calibration of the sensors.. lect "utomatic mode". TURN N / TURN FF outputs of TS-T+ (controller number ): utput : If ->4 C then the output is TURN N. The water heater is heated by the Solar collector. If -)<4 C then the output is TURN FF. utput : TURN N and TURN FF at depending on the programming of the weekly temperature timer (or manual setting of Td buttons '+' '-' in the automatic mode of the controller). If <Td C then the output is TURN N. The water heater is heated by electric heater. Td е желаната температура в бойлера (задава се с таймера). If S<6 C или (ST-SP)< C then the output is TURN FF. utput : If >6 C then the output is TURN N. Guide a warm to the water pool or the jacuzzi. If <6 C then the output is TURN FF. Guide a warm to the water pool or the water heater. utput 4: If >6 C и (-)>8 C then the output is TURN N. The water heater warm from boiler. If <6 C или (-)< C then the output is TURN FF. utput : If > C then the output is TURN N. nding hot water from the boiler to the convectors. If < C then the output is TURN FF. In the table above for the circle G6 (boiler-water heater) is allowed to operate only if the boiler temperature is exceeded by 6 C. Round G7 (boiler-convectors) be permitted upon reaching the temperature in the boiler C. It provides an advantage for convectors at withdrawal of heat from the boiler. The water heater will be heated only if remaining excess heat in the boiler. By changing the digits we can reduce, enhance or turn advantage. The advantage can be excluded temporarily or permanently into the row "Top Level-nsor" for rounds G6 set number sensor ''.
Row from the table for programming Top Level - C Top level thermostats ХХ= до 9 C Top Level-nsor nsor for thermostat top level S=-6 Low Level - C Low level thermostats ХХ= до 9 C Low Level-nsor nsor for thermostat top level S=-6 N TEMPERTURE - 9 C FF TEMPERTURE - 9 C sensor ST - 6 sensor SP - 6 Used logical function ND, R Table setup of the differential regulators, logical functions and thermostats. controller number G4 G G G8 G9 4 6 8 utput number 9 controlled round 68 6 4 Sh Note Temperature to TURN N Temperature to TURN N ST-SP to TURN N ST-SP to TURN FF nsor heat source nsory hot-receiver А(ND) / О(R) In the summer should be set - to prohibit the supply of heat from the fireplace to the convectors. In winter, must be set - to prohibit cooling by convectors. If you do not want heating jacuzzi from boiler must all the numbers of sensors in the column is set to. Programming:. t the time and date.. t the timer program if necessary.. Program the top table in the controller. 4. Perform calibration of the sensors.. lect "utomatic mode". TURN N / TURN FF outputs of TS-T+ (controller number ): utput : If >6 C and (-)>8 C then the output is TURN N. The water heater is heated by the fireplace. If <6 C or (-)< C then the output is TURN FF. Изход : TURN N or TURN FF depending on the programming of the weekly temperature timer. If <Td C then the output is TURN N. Perform watering. Td is the desired temperature in the tank (set from timer). If >Td C тthen the output is TURN FF. Изход : If > C then the output is TURN N. nding warm water from the fireplace to the convectors. If < C then the output is TURN FF. Изход 4: If >68 C and Sh<4 C then the output is TURN N. Jacuzzi is heated by the boiler. If <68 C or Sh>4 C then the output is TURN FF. Изход : If > C then the output is TURN N. nding cold water from well to convectors. If < C then the output is TURN FF. In the table above for the circle G4 (fireplace-tank) is allowed to operate only if the boiler temperature is exceeded by 6 C. Round G (fire-convectors) be permitted upon reaching the temperature in the fireplace C. It provides an advantage for convectors withdrawal of heat from the fireplace. The water heater will be heated only if have remaining excess heat in the fireplace. By changing the numbers we can reduce, enhance or turn advantage. The advantage can be excluded temporarily or permanently if into row "Top Level-nsor" for rounds G4 is assigned a number of sensor ''.
pportunities provided by the software "TS-plus" the controller gives the user great opportunities for selecting and changing the manner of control of the functional circuit. Probably many options are available for managing specific functional scheme, but will show just one more: Place the sensor '' (measured temperature of the air) in the largest room of the house. In winter heating indoor air will have prevail. tting maintained temperature in other rooms will be done by setting flow and local opportunities for adjustment of convectors. If the sensor '' display a temperature below the desired then heat from the fireplace will be directed only to the convectors. Row from the table for programming Top Level - C Top level thermostats ХХ= до 9 C Top Level-nsor nsor for thermostat top level S=-6 Low Level - C Low level thermostats ХХ= до 9 C Low Level-nsor nsor for thermostat top level S=-6 N TEMPERTURE - 9 C FF TEMPERTURE - 9 C sensor ST - 6 sensor SP - 6 Used logical function ND, R Table setup of the differential regulators, logical functions and thermostats. controller number G4 G G G8 G9 4 8 utput number 9 68 6 4 controlled round Sh Note Temperature to TURN N Temperature to TURN N ST-SP to TURN N ST-SP to TURN FF nsor heat source nsory hot-receiver А(ND) / О(R) In the summer should be set - to prohibit the supply of heat from the fireplace to the convectors. In winter, must be set - to prohibit cooling by convectors. If you do not want heating jacuzzi from boiler must all the numbers of sensors in the column is set to. Programming:. t the time and date.. t the timer program if necessary.. Program the top table in the controller. 4. Perform calibration of the sensors.. lect "utomatic mode". TURN N / TURN FF outputs of TS-T+ (controller number ): utput : If > C and (-)>8 C then the output is TURN N. The water heater is heated by the fireplace. If < C или (-)< C then the output is TURN FF. Изход : TURN N or TURN FF depending on the programming of the weekly temperature timer. If <Td C then the output is TURN N. Perform watering. Td is the desired temperature in the tank (set from timer). If >Td C then the output is TURN FF. Изход : If > C then the output is TURN N. nding warm water from the fireplace to the convectors. If < C then the output is TURN FF. Изход 4: If >68 C и Sh<4 C then the output is TURN N. Jacuzzi is heated by the boiler. If <68 C или Sh>4 C then the output is TURN FF. Изход : If > C then the output is TURN N. nding cold water from well to convectors. If < C then the output is TURN FF. In the table above for the circle G4 (fireplace-tank) is allowed to operate only if the boiler temperature is exceeded by C. Round G (fire-convectors) be permitted upon reaching the temperature in the fireplace C. It provides an advantage for convectors withdrawal of heat from the fireplace. The water heater will be heated only if have remaining excess heat in the fireplace. By changing the numbers we can reduce, enhance or turn advantage. The advantage can be excluded temporarily or permanently if into row "Top Level-nsor" for rounds G4 is assigned a number of sensor ''.
ption - Instead pump R7 used solenoid valve. fter cooling water is moving to a tank for drip irrigation. Besides settings from version to switch from winter to summer mode of governance must be made:. Rotate the manual three-way valve V for the movement of cooling water to the tank for drip irrigation.. t the flow of cooling water through the valve V4. Everything else remains the same as in option. R, R, R, R4, R, R6 - Heat pump. Sx - nsors. F - Thermal cutoff. B - Electric heater. Non-return valve. Функционална схема V - Three-way manual valve. А9 - Solar collector(s). V - Three-way solenoid valve V4 - Two-way manual valve. - nsor for measuring air temperature А- Water heater (tank) V R4 R B V А - swimming pool Sg К А7 - Boiler А - convector (s) К К4 К А8 - Fireplace К6 К7 Sh А - jacuzzi Two-way solenoid valve К R7 V tank to drip irrigation R А4 - Well V4 R А - hydrophore pump. R R6 А - Two-way solenoid valve The coils in the pool and jacuzzi are set arbitrarily. In practice it is more efficient use of aluminum radiators. А - water sprinklers for watering lawns.