How To Use An Akua Magnetic Lime Scale Preventing Device

Transcription

1

2 AKUA MAGNETIC LIMESCALE PREVENTING DEVICES INTRODUCTION AND OPERATING MANUAL This manual contains information about Akua Magnetic Lime Scale Preventing devices, their assembly and usage rules. In order to benefit from devices effectively, the assembly and usage rules are have to be obeyed. 1) Definition Magnetic Lime Scale Preventing Devices function changing the crystal structure of lime (calcium carbonate) in the water with helping the magnetic field produced by the magnets inside the device. Calcite crystal of lime (calcium carbonate) sticks on the internal wall of devices and installations. The calcite crystals are changed to the aragonite crystal that is carrying with water, soft and also noncohesive by Akua Magnetic Lime Scale Preventing Devices. Therefore, it prevents lime in the installation and devices. 2) FEATURES 2.1) General Features Akua Magnetic Lime Scale Preventing Devices are manufactured with flanged (from 2 to 40 ) and with screwed (from 1/2 to 1 1/2 ) Akua have 8 types of geared screwed devices,, 1/2, 3/4 S, 3/4 K, 3/4 B, 3/4 Y, 1, 1 1/4 and 1 1/2 and also have 22 types of flanged devices from 2 to 40 All of the Akua Magnetic Lime Scale Preventing Devices are manufactured by using AISI304 quality Stainless steel body and fixing component and also covered with the polyethylene sheath. Akua Magnetic Lime Scale Preventing Devices can be operated in four different temperature values, 90 C, 180 C, 250 C and 800 C Depends on the usage temperature of devices, different types of magnet used. Magnets are manufactured from the allays of, neodyum iron boron (NdFeB) or samarium Cobalt (SmCo) or Aluminum Nickel Cobalt (AlNiCo) that have to Gauss magnetic flux density. All the magnets outer surface is covered with zinc, nickel or epoxide.

3 2.2) Technical Features Akua Magnetic Lime Scale Preventing Devices technical features are given below.

4 2.2) Technical Features Akua Magnetic Limescale Preventing Devices technical features are given below.

5 3) General Rules Akua Magnetic Lime Scale Preventing Devices are manufactured with flanged (from 2 to 40 ) and with screwed (from 1/2 to 1 1/2 ) Akua Magnetic Lime Scale Preventing Devices can be assembled in any direction (water inlet/ output) and position (horizontal/vertical). Besides this, due to 1/2, 3/4 S, 3/4 K and 3/4 B devices have male and female screw thread. female screwed side should be installed faced to water inlet; male screwed side faced to water outlet. Akua Magnetic Lime Scale Preventing Devices are manufactured to connect pipes which have only the same nominal diameters with devices. If necessary, devices can be connected with one below or one above diameter pipe by using reduction components. In this situation, you have to be discussed with Akua Foreign Trade Limited Company about montages because The Company isn t responsible for low performance that occurs from wrong montage. Akua Magnetic Lime Scale Preventing Devices release without any accessories (sleeve coupling, clamping sleeve, nipple, gasket, contrary flange, etc.) on it. Such kind of assembly components have to supply by user. Assembly of device is in users responsibility. It is necessary that Akua Magnetic Lime Scale Preventing Devices are assembled to a proper point to pipe. Detailed information about assembly of the devices is given next chapters. Paying attention to information in these chapters is important. During the assembly of devices, the users shouldn t use overpower. If devices screw thread, flange has damage or in any other reason occurs due to overpower is evaluated as outside the scope of warranty. Akua Magnetic Lime Scale Preventing Devices are work efficiently till the temperature shown on the devices. If the temperature of the water higher than the temperature shown on the device, efficiency of the device start to drop. Akua Magnetic Lime Scale Preventing Devices must be assembled to pipes which have no valves, corners, water meter, etc. on it near the device for 20 cm. In brief, There should be a straight part of pipe length of which is minimum 20 cm before and after the device assembled. Magnetic Lime Scale Preventing Devices transfers the magnetic effect to the minerals within the water due to fact that water is conductive. In this respect, the magnetic effect will always occur as long as water flows in it. When the flow of water is cutten, magnetic effect will conserve itself for approximately 24 hours. Whenever flow is started again, magnetic field occurs again and lime is solved. Devices that assembled to buildings inlet waterline protects open water circuits like sinks, toilets, baths etc. But for the closed water circuits like heaters, boilers, and autoclave machines etc. another device should be assembled. Because water is periodically transferred to depots or containers. Heavy Metals like Ferrous, Cadmium Cobalt, Chromium, etc and Silisium have harmful effects on the performance of magnetic lime prevention devices. Device can be operated effectively with water which contains heavy metal and Silisium but before magnetic lime prevention device there should be a Magnetic Heavy Metal Trap device exists. Akua Magnetic Lime Scale Preventing Devices work without maintenance or repair.

6 4) Assembly of devices to pipes 4.1) Screwed Devices Akua Magnetic Lime Scale Preventing Devices are used by connecting devices to pipes. From this point of, on the pipes that devices will be assembled, the total length of devices and assembly components must be cut from the related pipe. Devices which have 1/2, 3/4 K and 3/4 B nominal diameters have male and female screw connections, devices which have 3/4 Y, 1, 1 1/4 and 1 1/2 nominal diameters have only male screw connections. Assembly of devices which have 1/2, 3/4 K and 3/4 B nominal diameters are shown in the picture below. In order to assemble, two units of 3/4 sleeve coupling and one 3/4 nipple must use. Assembly of devices which have 3/4 Y, 1, 1 1/4 and 1 1/2 nominal diameters are shown in the picture below. In order to assemble, four units of 3/4 sleeve coupling and two units of 3/4 nipple must use. Attention: Above the picture there is only one side connection detailed information given. The connection must be done the same as for the other side!

7 4.2) Flanged Devices From 2 to 40 devices have flanged connection. Devices are assembled by using suitable two unit flange and two unit gasket. Assembly can be done by the way shown in the picture below. 5) Connection Points According to Usage Area According to usage area Akua Magnetic Lime Scale Preventing Devices connection points are given below. 5.1) Heating Boilers Heating Boilers are closed circuit. Heated water in boiler, periodically transfer between boiler and radiators. For this reason Akua Magnetic Lime Scale Preventing Devices are needed to be montaged to hot water outlet line, before or after collector.

8 5.2) Boilers Devices should be montaged to heater water and cold water inlet lines as shown in picture below. 5.4) Solar Collector For Solar Collectors, devices should be montaged to only cold water inlet line. 5.3) Heat Exchangers Devices should be montaged to plate type and pipe type heat exchangers on hot water and cold water inlet lines. 5.5) Air Conditioning Systems Where the devices should be located to the air conditioning system, is shown in the picture below.

9 5.6) Combo Heaters In Combo Heaters, there are two different water circuit called open water circuit and close water circuit. A device assembled to the building main water inlet, will protect only open circuits of combo heaters. For the closed circuits, there is need for another device and it should be located after pump. 5.7) Autoclave Machine Autoclave machines have open circuit water lines. Besides this, devices should be located between the outlet of pumps and steam generators inlet because water keeps waiting in depot. Location for Autoclave machines is shown as in the picture below. 5.8) Water Cooling Towers Devices should be montaged only to the lines of the hot water inlet.

10 5.9) Thermal and Gas Power Plants In thermal and gas power plants, devices should be installed in points as shown in picture. 5.10) Geothermal Applications Devices should be located in Geothermal Applications. The Assembly of Geothermal Applications as in the picture below. 5.11) Swimming Pools Devices should be assembled to swimming pools as shown in the picture below.

11 5.12) Water Purification Devices Devices Should be in entrance of running water inlet 5.13) Irrigation systems Devices should be assembled to Irrigation Systems water depot outlet. 5.14) Milk Cooling Tanks Devices should be assembled to the cooling water line of Milk Cooling Tanks as shown in the picture below. Attention: For the different processes, you can get information by calling Akua Foreign Trade Co. or by sending .

12 6) Adjustments Akua Magnetic Lime Scale Preventing Devices don t need any adjustments. You should do leakage control, only. 7) Maintenance and Repair Akua Magnetic Lime Scale Preventing Devices don t require maintenance and repair. 8) Warnings -Devices should place on points as far as possible away from the machines and installations which can be affected by magnetic field.. -Devices should keep away from people with pacemaker and electronic devices such as, computers, cellular phones, clocks, because of the strong magnetic field. -During devices montage, all safety precautions must be taken. -During the assembly of flanged devices, there is spark so in workspace, certainly there shouldn t be any explosive and flammable materials. -Devices have to be installed considering the rules and connecting schemes. -Leakage control should be checked after the connecting of devices is finished. -If necessary, the pipes on which the heavy devices are installed should be supplied from appropriate points for balancing loads. AKUA MAGNETIC LIMESCALE PREVENTING DEVICES ARE GUARANTEED FOR 5 YEARS AKUA INTERNATIONAL TRADE COMPANY

13 AKUA MAGNETIC LIMESCALE PREVENTING DEVICES Produce in TURKEY with CE certificate MANUFACTURED COMPANY AKUA INTERNATIONAL TRADE COMPANY Atatürk Bulvarı No: 158/18 Çankaya/ANKARA Tel: +90 (312) Gsm: +90 (532) (505) Fax: +90 (312) akua15@superonline.com