LTC1 Dual 24V High-Side MOSFET Driver FEATRES Fully Enhances N-Channel Power MOSFETs 12µA Standby Current Operates at Supply Voltages from 9V to 24V Short Circuit Protection Easily Protected Against Supply Transients Controlled Switching ON and OFF Times No External Charge Pump Components Compatible With Standard Logic Families Available in 8-Pin SOIC APPLICATI O S Solenoid Drivers DC Motor Drivers Stepper Motor Drivers Lamp Drivers/Dimmers Relay Drivers Low Frequency H-Bridge P-Channel Switch Replacement DESCRIPTIO The LTC1 dual high-side driver allows using low cost N-channel FETs for high-side industrial and automotive switching applications. An internal charge pump boosts the gate drive voltage above the positive rail, fully enhancing an N-channel MOS switch with no external components. Low power operation, with 12µA standby current, allows use in virtually all systems with maximum efficiency. Included on-chip is independent overcurrent sensing to provide automatic shutdown in case of short circuits. A time delay can be added to the current sense to prevent false triggering on high in-rush current loads. The LTC1 operates from 9V to 24V supplies and is well suited for industrial and automotive applications. The LTC1 is available in both an 8-pin DIP and an 8-pin SOIC. TYPICAL APPLICATI O Dual 24V High-Side Switch with Overcurrent Protection Standby Supply Current 24V IRLR24 1µF.36Ω.36Ω LTC1 IRLR24 SPPLY CRRENT (µa) 4 4 3 3 2 1 V = V = V T A = C 24V/.A SOLENOID 1N41 µp, ETC. µp, ETC. 1N41 24V/.A SOLENOID 1 LTC1 TA1 1 1 2 SPPLY VOLTAGE (V) 3 LTC1 TA2 1
LTC1 ABSOLTE AXI RATI GS W W W Supply Voltage....3V to 3V Transient Supply Voltage (< 1ms)... 4V Input Voltage... (.3V) to (.3V) Gate Voltage... ( 2V) to (.3V) Current (Any Pin)... ma Operating Temperature Range LTC1C... C to 7 C LTC1I... 4 C to 8 C Storage Temperature Range... 6 C to 1 C Lead Temperature (Soldering, 1 sec)... 3 C PACKAGE/ORDER I FOR 1 GATE 1 2 3 4 TOP VIEW N8 PACKAGE 8-LEAD PLASTIC DIP T JMAX = 1 C, θ JA = 13 C/ W 8 7 GATE 2 6 W ATIO ORDER PART NMBER LTC1CN8 LTC1IN8 1 GATE 1 2 3 4 TOP VIEW S8 PACKAGE 8-LEAD PLASTIC SOIC T JMAX = 1 C, θ JA = 1 C/W 8 7 GATE 2 6 ORDER PART NMBER LTC1CS8 LTC1IS8 S8 PART MARKING 1 1I ELECTRICAL CHARA CTERISTICS = 9V to 24V, T A = C, unless otherwise noted. SYMBOL PARAMETER CONDITIONS MIN TYP MAX NITS I Q Quiescent Current OFF = 1V, V IN = V (Note 1) 12 4 µa = 18V, V IN = V (Note 1) 12 4 µa = 24V, V IN = V (Note 1) 12 4 µa Quiescent Current ON = 1V, V GATE = 22V, V IN = V (Note 2) 16 4 µa = 18V, V GATE = 3V, V IN = V (Note 2) 3 8 µa = 24V, V GATE = 36V, V IN = V (Note 2) 6 12 µa V INH Input High Voltage 2 V V INL Input Low Voltage.8 V I IN Input Current V V IN ±1 µa C IN Input Capacitance pf EN Drain Sense Threshold Voltage 8 1 12 mv 7 1 1 mv I SEN Drain Sense Input Current V EN ±.1 µa V GATE Gate Voltage Above Supply = 9V 7. 1. 12 V I GATE Gate Output Drive Current = 18V, V GATE = 3V 2 µa = 24V, V GATE = 36V 23 µa 2
ELECTRICAL CHARA CTERISTICS = 9V to 24V, T A = C, unless otherwise noted. LTC1 SYMBOL PARAMETER CONDITIONS MIN TYP MAX NITS t ON Turn-ON Time = 1V, C GATE = 1pF (Note 3) Time for V GATE > 2V 3 1 3 µs Time for V GATE > V 7 7 µs = 18V, C GATE = 1pF (Note 3) Time for V GATE > V 4 12 4 µs Time for V GATE > 1V 7 7 µs = 24V, C GATE = 1pF (Note 3) Time for V GATE > 1V 18 µs t OFF Turn-OFF Time = 1V, C GATE = 1pF, (Note 3, 4) 1 24 6 µs = 18V, C GATE = 1pF, (Note 3, 4) 1 21 6 µs = 24V, C GATE = 1pF, (Note 3, 4) 1 19 6 µs t SC Short-Circuit Turn-OFF Time = 1V, C GATE = 1pF, (Note 3, 4) 16 3 µs = 18V, C GATE = 1pF, (Note 3, 4) 16 3 µs = 24V, C GATE = 1pF, (Note 3, 4) 16 3 µs The denotes specifications which apply over the full operating temperature range. Note 1: Quiescent current OFF is for both channels in OFF condition. Note 2: Quiescent current ON is per driver and is measured independently. The gate voltage is clamped to above the rail to simulate the effects of protection clamps connected across the GATE-SORCE of the power MOSFET. Note 3: Zener diode clamps must be connected across the GATE-SORCE of the power MOSFET to limit V GS. 1N242A (through hole) or MMBZ242A (surface mount) Zener diodes are recommended. All Turn-ON and Turn-OFF tests are performed with a Zener clamp in series with a small-signal diode connected between and the GATE output to simulate the effects of a protection Zener clamp connected across the GATE-SORCE of the power MOSFET. Note 4: Time for V GATE to drop below 1V. TYPICAL PERFOR A W CE CHARA CTERISTICS Standby Supply Current Supply Current per Driver (ON) Gate Voltage Above Supply SPPLY CRRENT (µa) 4 4 3 3 2 1 V = V = V T A = C SPPLY CRRENT (ma) 2. 1.8 1.6 1.4 1.2 1..8.6 ONE INPT = N OTHER INPT = OFF T A = C VGATE VS (V) 2 18 16 14 12 1 8 6 V CLAMP = 1.4 4.2 2 1 1 2 SPPLY VOLTAGE (V) 3 1 1 2 SPPLY VOLTAGE (V) 3 1 1 2 SPPLY VOLTAGE (V) 3 LTC1 TPC1 LTC1 TPC2 LTC1 TPC3 3
LTC1 TYPICAL PERFOR A W CE CHARA CTERISTICS Input Threshold Voltage Drain Sense Threshold Voltage Gate Clamp Current INPT THRESHOLD VOLTAGE (V) 2.4 2.2 2. 1.8 1.6 1.4 1.2 1..8.6 V ON V OFF DRAIN SENSE THRESHOLD VOLTAGE (V) 1 12 11 11 1 1 9 9 8 8 T A = C GATE CLAMP CRRENT (µa) 4 4 3 3 2 1 1 V CLAMP = T A = C.4 1 1 2 SPPLY VOLTAGE (V) 3 7 1 1 2 SPPLY VOLTAGE (V) 3 1 1 2 SPPLY VOLTAGE (V) 3 LTC1 TPC4 LTC1 TPC LTC1 TA6 Turn-ON Time Turn-OFF Time Short-Circuit Turn-OFF Delay Time 1 9 8 C GATE = 1pF T A = C 4 4 C GATE = 1pF TIME FOR V GATE < 1V 4 4 C GATE = 1pF TIME FOR V GATE < 1V TRN-ON TIME (µs) 7 6 4 3 2 V GS = V TRN-OFF TIME (µs) 3 3 2 1 1 TRN-OFF TIME (µs) 3 3 2 1 1 1 V GS = 2V 1 1 2 SPPLY VOLTAGE (V) 3 1 1 2 SPPLY VOLTAGE (V) 3 1 1 2 SPPLY VOLTAGE (V) 3 LTC1 TA7 LTC1 TA8 LTC1 TA9 Standby Supply Current Supply Current per Channel (ON) Input ON Threshold 2. 2.4 STANDBY SPPLY CRRENT (µa) 4 4 3 3 2 1 1 = 1V = 18V = 24V SPPLY CRRENT (ma) 1.8 1.6 1.4 1.2 1..8.6.4.2 = 24V = 18V = 1V INPT THRESHOLD VOLTAGE (V) 2.2 2. 1.8 1.6 1.4 1.2 1..8.6 = 1V = 24V TEMPERATRE ( C) 7 1 TEMPERATRE ( C) 7 1.4 TEMPERATRE ( C) 7 1 LTC1 TA1 LTC1 TA11 LTC1 TA12 4
PI F CTIO S Input Pin The LTC1 input pin is active high and activates all of the protection and charge pump circuitry when switched ON. The LTC1 logic and shutdown inputs are high impedance CMOS gates with ESD protection diodes to ground and supply and therefore should not be forced beyond the power supply rails. The input pin should be held low during the application of power to properly set the input latch. Gate Drive Pin The gate drive pin is either driven to ground when the switch is turned OFF or driven above the supply rail when the switch is turned ON. This pin is of relatively high impedance when driven above the rail (the equivalent of a few hundred kω). Care should be taken to minimize any loading of this pin by parasitic resistance to ground or supply. Supply Pin The supply pin of the LTC1 serves two vital purposes. The first is obvious; it powers the input, gate drive, regulation and protection circuitry. The second purpose is less obvious; it provides a Kelvin connection to the top of the drain sense resistor for the internal 1mV reference. The supply pin of the LTC1 should never be forced below ground as this may result in permanent damage to the device. A 1Ω resistor should be inserted in series with the ground pin if negative supply voltage transients are anticipated. LTC1 The LTC1 is designed to be continuously powered so that the gate of the MOSFET is actively driven at all times. If it is necessary to remove power from the supply pin and then reapply it, the input pin should be cycled (low to high) a few milliseconds after the power is reapplied to reset the input latch and protection circuitry. Also, the input pin should be isolated from the controlling logic by a 1k resistor if there is a possibility that the input pin will be held high after the supply has been removed. Drain Sense Pin The drain sense pin is compared against the supply pin voltage. If the voltage at this pin is more than 1mV below the supply pin, the input latch will be reset and the MOSFET gate will be quickly discharged. Cycle the input to reset the short-circuit latch and turn the MOSFET back on. This pin is also a high impedance CMOS gate with ESD protection and therefore should not be forced outside of the power supply rails. To defeat the overcurrent protection, short the drain sense pin to the supply pin. Some loads, such as large supply capacitors, lamps or motors require high in-rush currents. An RC time delay can be added between the sense resistor and the drain sense pin to ensure that the drain sense circuitry does not false trigger during startup. This time constant can be set from a few microseconds to many seconds. However, very long delays may put the MOSFET at risk of being destroyed by a short-circuit condition (see Applications Information section). OPERATIO The LTC1 is a dual 24V MOSFET driver with built-in protection and gate charge pump. The LTC1 consists of the following functional blocks: TTL and CMOS Compatible Inputs and Latches The LTC1 inputs have been designed to accommodate a wide range of logic families. Both input thresholds are set at about 1.3V with approximately 1mV of hysteresis. A low standby current regulator provides continuous bias for the TTL-to-CMOS converter. The input/protection latch should be set after initial power-up, or after reapplication of power, by cycling the input low to high.
LTC1 OPERATIO Internal Voltage Regulation The output of the TTL-to-CMOS converter drives two regulated supplies which power the low voltage CMOS logic and analog blocks. The regulator outputs are isolated from each other so that the noise generated by the charge pump logic is not coupled into the 1mV reference or the analog comparator. Gate Charge Pump Gate drive for the power MOSFET is produced by an adaptive charge pump circuit which generates a gate voltage substantially higher than the power supply voltage. The charge pump capacitors are included on-chip and therefore no external components are required to generate the gate drive. The charge pump is designed to drive a Zener diode clamp connected across the gate and source of the MOSFET switch. Drain Current Sense The LTC1 is configured to sense the current flowing into the drain of the power MOSFET in a high-side application. An internal 1mV reference is compared to the drop across a sense resistor (typically.2ω to.1ω) in series with the drain lead. If the drop across this resistor exceeds the internal 1mV threshold, the input latch is reset and the gate is quickly discharged via a relatively large N-channel transistor. Controlled Gate Rise and Fall Times When the input is switched ON and OFF, the gate is charged by the internal charge pump and discharged in a controlled manner. The charge and discharge rates have been set to minimize RFI and EMI emissions in normal operation. If a short circuit or current overload condition is encountered, the gate is discharged very quickly (typically a few microseconds) by a large N-channel transistor. BLOCK DIAGRA W (One Channel) ANALOG SECTION DRAIN SENSE LOW STANDBY CRRENT REGLATOR 1mV REFERENCE COMP 1µs DELAY GATE CHARGE AND DISCHARGE CONTROL LOGIC GATE ANALOG DIGITAL INPT TTL-TO-CMOS CONVERTER VOLTAGE REGLATOR ONE SHOT R S INPT LATCH OSCILLATOR AND CHARGE PMP FAST/SLOW GATE CHARGE LOGIC LTC1 BD 6
LTC1 W APPLICATIO S I FOR ATIO MOSFET AND LOAD PROTECTION The LTC1 protects the power MOSFET switch by removing drive from the gate as soon as an overcurrent condition is detected. Resistive and inductive loads can be protected with no external time delay in series with the drain sense pin. Lamp loads, however, require that the overcurrent protection be delayed long enough to start the lamp but short enough to ensure the safety of the MOSFET. Resistive Loads Loads that are primarily resistive should be protected with as short a delay as possible to minimize the amount of time that the MOSFET is subjected to an overload condition. The drain sense circuitry has a built-in delay of approximately 1µs to eliminate false triggering by power supply or load transient conditions. This delay is sufficient to mask short load current transients and the starting of a small capacitor (<1µF) in parallel with the load. The drain sense pin can therefore be connected directly to the drain current sense resistor as shown in Figure 1. 18V 1/2 LTC1 1µF C LOAD 1µF LTC1 F1 R SENSE.36Ω IRFZ24 R LOAD 18Ω Figure 1. Protecting Resistive Loads Inductive Loads Loads that are primarily inductive, such as relays, solenoids and stepper motor windings, should be protected with as short a delay as possible to minimize the amount of time that the MOSFET is subjected to an overload condition. The built-in 1µs delay will ensure that the overcurrent protection is not false triggered by a supply or load transient. No external delay components are required as shown in Figure 2. Large inductive loads (>.1mH) may require diodes connected directly across the inductor to safely divert the stored energy to ground. Many inductive loads have these diodes included. If not, a diode of the proper current rating should be connected across the load, as shown in Figure 2, to safely divert the stored energy. Figure 2. Protecting Inductive Loads Capacitive Loads Large capacitive loads, such as complex electrical systems with large bypass capacitors, should be powered using the circuit shown in Figure 3. The gate drive to the power MOSFET is passed through an RC delay network, R1 and C1, which greatly reduces the turn-on ramp rate of the switch. And since the MOSFET source voltage follows the gate voltage, the load is powered smoothly and slowly from ground. This dramatically reduces the startup current flowing into the supply capacitor(s) which, in turn, reduces supply transients and allows for slower activation 1V 1/2 LTC1 1/2 LTC1 IRFZ24 Figure 3. Powering Large Capacitive Loads C DELAY.1µF R1 D1 1µF 1N4 LTC1 F2 R DELAY R2 C1.33µF R SENSE.36Ω, 1A SOLENOID 47µF R SENSE.36Ω LTC1 F3 MTP3E C LOAD 1µF 7
LTC1 W APPLICATIO S I FOR ATIO of sensitive electrical loads. (Resistor R2, and the diode D1, provide a direct path for the LTC1 protection circuitry to quickly discharge the gate in the event of an overcurrent condition.) The RC network, R DELAY and C DELAY, in series with the drain sense input should be set to trip based on the expected characteristics of the load after startup, i.e., with this circuit, it is possible to power a large capacitive load and still react quickly to an overcurrent condition. The ramp rate at the output of the switch as it lifts off ground is approximately: dv/dt = (V GATE V TH )/(R1 C1) Therefore, the current flowing into the capacitor during startup is approximately: I STARTP = C LOAD dv/dt sing the values shown in Figure 3, the startup current is less than 1mA and does not false trigger the drain sense circuitry which is set at 2.7A with a 1ms delay. Lamp Loads The in-rush current created by a lamp during turn-on can be 1 to 2 times greater than the rated operating current. The circuit shown in Figure 4 shifts the current limit threshold up by a factor of 11:1 (to 3A) for a short period of time while the bulb is turned on. The current limit then drops down to 2.7A after the in-rush current has subsided. 1/2 LTC1 1k 1M VN2222LL.1µF 47µF R SENSE.36Ω 9.1V LTC1 F4 Figure 4. Lamp Driver With Delayed Protection MTP3EL /1A BLB Selecting R DELAY and C DELAY Figure is a graph of normalized overcurrent shutdown time versus normalized MOSFET current. This graph is used to select the two delay components, R DELAY and C DELAY, which make up a simple RC delay between the drain sense input and the drain sense resistor. The Y axis of the graph is normalized to one RC time constant. The X axis is normalized to the set current. (The set current is defined as the current required to develop 1mV across the drain sense resistor.) Note that the shutdown time is shorter for increasing levels of MOSFET current. This ensures that the total energy dissipated by the MOSFET is always within the bounds established by the manufacturer for safe operation. (See MOSFET data sheet for further S.O.A. information.) NORMALIZED DELAY TIME (1 = RC) 1 1.1.1.1 1 1 1 NORMALIZED MOSFET CRRENT (1 = SET CRRENT) LTC1 F Figure. Normalized Delay Time vs MOSFET Current sing a Speed-p Diode Another way to reduce the amount of time that the power MOSFET is in a short-circuit condition is to bypass the delay resistor with a small signal diode as shown in Figure 6. The diode will engage when the drop across the drain sense resistor exceeds about.7v, providing a direct path to the sense pin and dramatically reducing the amount of time the MOSFET is in an overload condition. The drain sense resistor value is selected to limit the maximum DC current to 4A. 8
LTC1 W APPLICATIO S I FOR ATIO 18V 1/2 LTC1 C DELAY.1µF R DELAY Figure 6. sing a Speed-p Diode Current Limited Power Supplies 1µF R SENSE.36Ω LTC1 F6 LOAD IRF3 The LTC1 requires at least 3.V at the supply pin to ensure proper operation. It is therefore necessary that the supply to the LTC1 be held higher than 3.V at all times, even when the output of the switch is short circuited to ground. The output voltage of a current limited regulator may drop very quickly during short circuit and pull the supply pin of the LTC1 below 3.V before the shutdown circuitry has had time to respond and remove drive from the gate of the power MOSFET. A supply filter should be added as shown in Figure 7 which holds the supply pin of the LTC1 high long enough for the overcurrent shutdown circuitry to respond and fully discharge the gate. Linear regulators with small output capacitors are the most difficult to protect as they can switch from a voltage mode to a current limited mode very quickly. The large output capacitors on many switching regulators, on the other hand, may be able to hold the supply pin of the LTC1 above 3.V sufficiently long that this extra filtering is not required. Because the LTC1 is micropower in both the standby and ON state, the voltage drop across the supply filter is very small (typically <6mV) and does not significantly alter the accuracy of the drain sense threshold voltage which is typically 1mV. ATOMOTIVE APPLICATIONS Reverse Battery Protection The LTC1 can be protected against reverse battery conditions by connecting a resistor in series with the ground lead as shown in Figure 8. The resistor limits the supply current to less than 12mA with applied. Since the LTC1 draws very little current while in normal operation, the drop across the ground resistor is minimal. The V µp (or controlling logic) is protected by the 1k resistors in series with the input. V µp OR CONTROL LOGIC 1k 1/2 LTC1 1Ω 28V 1µF LOAD R SENSE.36Ω MTP12N6E 1V 1µF /2A REGLATOR 47µF* 1/2 LTC1 1Ω*.1µF Figure 7. Supply Filter for Current Limited Supplies *SPPLY FILTER COMPONENT 1µF R SENSE.1Ω LTC1 F7 MTP12N6E SHORT CIRCIT LTC1 F8 Figure 8. Reverse Battery Protection Transient Overvoltage Protection A common scheme used to limit overvoltage transients on a nominal automotive power bus is to clamp the supply to the module containing the high-side MOSFET switches with a large transient suppressor diode, D1 in Figure 9. This diode limits the supply voltage to 4V under worse case conditions. The LTC1 is designed to survive short (1ms) 4V transients and return to normal operation after the transient has passed. 9
LTC1 W APPLICATIO S I FOR ATIO The switches can either be turned OFF by the controlling logic during these transients or latched OFF above 3V by holding the drain sense pin low as shown in Figure 9. Switch status can be ascertained by means of an XNOR gate connected to the input and switch output through current limiting resistors (see Typical Applications section for more detail on this scheme). The switch is reset after the overvoltage event by cycling the input low and then high again. The power MOSFET switch should be selected to have a breakdown voltage sufficiently higher than the 4V supply clamp voltage to ensure that no current is conducted to the load during the transient. µp, ETC. 1k 1µF V 1/2 LTC1 1Ω Figure 9. Overvoltage Transient Protection D1 MR3L 1k* 1N242B 3V* 1N6B LTC1 F9 LOAD *OPTIONAL OVERVOLTAGE (3V) LATCH-OFF COMPONENTS R SENSE.36Ω IRF3 TYPICAL APPLICATIO S Dual Automotive High-Side Switch with Overvoltage Protection, XNOR Status and 12µA Standby Current.36Ω 1µF V MR3L*.36Ω 1k** MTD3E /1A SOLENOID MMBZ242B 1N4 1k 1k LTC1 MTD3E 1k** MMBZ242B 1N4 /1A SOLENOID 1/4 74C266 1Ω 1/4 74C266 FALT TO µp µp, ETC. µp, ETC. FALT TO µp LTC1 TA3 TRTH TABLE IN OT 1 1 1 1 CONDITION SWITCH OFF OVERCRRENT OPEN LOAD** SWITCH ON FALT 1 1 *LIMITS TRANSIENTS TO <4V. SEE MANFACTRER DATA SHEET FOR FRTHER DETAIL. **OPTIONAL OPEN LOAD DETECTION REQIRES 1k PLL-P RESISTORS. (LTRA LOW STANDBY QIESCENT CRRENT IS SACRIFICED) POWER V LOGIC SPPLY. 1
LTC1 TYPICAL APPLICATIO S 1 to 12 Cell Battery Switch and V Ramped Load Switch with 12µA Standby Current and Optional 3A Overcurrent Shutdown 18V TO 3V BATTERY CHARGER 1 TO 12 CELL BATTERY PACK 9.1V MMBZ239BL 1k 2N2222 1k 1N4.33Ω*.22µF* * IRFR24 MMBZ242BL IRFR24 1µF V IN HIGH EFFICIENCY SWITCHING REGLATOR V OT SWITCHED BATTERY V/1A 1µF V LOGIC µp OR CONTROL LOGIC LTC1 *OPTIONAL 3A OVERCRRENT SHTDOWN SEE LTC1149 DATA SHEET FOR CIRCIT DETAILS 1k.1µF LTC1 TA4 MTD3EL V/1A (SWITCHED) Automotive Motor Direction and Speed Control with Stall-Current Shutdown MR3L V MOTOR SPEED AND DIRECTION CONTROL LOGIC OR µp 1µF V DIRECTION DIRECTION PWM 1 PWM 2.1µF LTC1 1Ω.1µF 3k 3k MMBZ242B MTD3E MMBZ242B DC MOTOR.2Ω MTD3E MTD3EL MTD3EL LTC1 TA 11
LTC1 TYPICAL APPLICATIO S Low Frequency (f O = 1Hz) PWM Motor Speed Control with Current Limit and 22V Overvoltage Shutdown OFF SLOW MED FAST 6k 3k 1k 1k.1µF MR3L 6 2.1µF 9.1k 8 4 LMC 3 1µF V 1µF.6V 1.1µF V LTC1 1Ω.47µF 1k 22V MMBZ1BL 1k 22V MMBZ1BL MR7.1Ω IRFR24 MOTOR LTC1 TA6 Dual Automotive Lamp Dimmer with Controlled Rise and Fall Times and Short-Circuit Protection PLSE WIDTH ADJST 1k MR3L.1µF 1µF V 9.1k 1µF.6V 8 4 6 2 LMC 3.1µF 1.1µF LTC1 3k 3k.1µF.1µF.Ω MMBZ242B MTD3E MMBZ242B.Ω MTD3E 1Ω #3 BLBS LTC1 TA6 12
LTC1 TYPICAL APPLICATIO S 18V to 32V Operation with Overcurrent Shutdown and Optional Overvoltage Shutdown 18V TO 32V 24V 1N2B µp, ETC. 1µF V 1k V S 1/2 LTC1 2N394 1k 2N396 36V* 1N8B 1k 1k 1N242B R SEN.1Ω 1W (I MAX = V BE /R SEN ) IRF3 *OPTIONAL 36V OVERVOLTAGE SHTDOWN 18V TO 32V LOAD LTC1 TA8 Bootstrapped Gate Driver (1Hz < f O < 1kHz) High-Side Switch with Thermal Shutdown (PTC Thermistor) 9V TO 24V 1µF.36Ω 9V TO 24V 1µF PTC* THERMISTOR (1 C) µp, ETC. 1/2 LTC1 1N242B 2N2222 *.1µF IRFZ44 µp, ETC. 1/2 LTC1 1N242B IRF3 *V GS =.6V (CLAMPED AT ) RISE AND FALL TIMES ARE BETA TIMES FASTER 2N396 LTC1 TA9 LOAD *KEYSTONE RL26-1-1-3-PT LTC1 TA1 LOAD 13
LTC1 TYPICAL APPLICATIO S H-Bridge DC Motor Driver (Direction and ON/OFF Control) 9V TO 24V V 1µF V LTC1.33µF.36Ω 1/4 74C2 1/4 74C2 MMBZ242B MTD3E MMBZ242B MTD3E DC MOTOR 1/4 74C2 MTD3EL DIRECTION DISABLE MTD3EL LTC1 TA11 High-Side DC Motor Driver With Electronic Braking and Stalled Motor Shutdown RN/COAST 18V V 1/4 74C2 1/4 74C2 1µF LTC1 3k.47µF 1N242B.2Ω IRFZ34 BRAKE *SIZE RESISTOR TO DISSIPATE ENERGY REGENERATED BY MOTOR DRING BRAKING. 3k 1N242B 1Ω* IRFZ34 1N4 18V DC MOTOR LTC1 TA12 14
LTC1 TYPICAL APPLICATIO S Stepper Motor Driver with Overcurrent Protection.1µF.36Ω 1µF.36Ω.1µF V STEPPER MOTOR CONTROL LOGIC A B C LTC1 IRFR24 MMBZ242BL IRFR24 MMBZ242BL STEPPER MOTOR WINDINGS A C 1N41 1N41 B D IRFR24 MMBZ242BL IRFR24 MMBZ242BL LTC1 D 1N41 1N41 LTC1 TA13 Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights. 1
LTC1 PACKAGE DESCRIPTIO Dimensions in inches (millimeters) unless otherwise noted. N8 Package 8-Lead Plastic DIP.4 (1.16) MAX 8 7 6. ±.1 (6.3 ±.4) 1 2 3 4.3.32 (7.62 8.128).4.6 (1.143 1.61).13 ±. (3.32 ±.127).9.1 (.229.381).3..1.63 8..381 ( ).6 (1.61) TYP.4 ±.1 (1.143 ±.381).1 ±.1 (2.4 ±.4).1 (3.17) MIN.18 ±.3 (.47 ±.76).2 (.8) MIN N8 393 S8 Package 8-Lead SOIC.189.197 (4.81.4) 8 7 6.228.244 (.791 6.197).1.17 (3.81 3.988) 1 2 3 4.8.1 (.23.4).1.2 (.4.8) 4 8 TYP.3.69 (1.346 1.72).4.1 (.11.4).16..46 1.27.14.19 (.3.483). (1.27) BSC SO8 393 16 Linear Technology Corporation 163 McCarthy Blvd., Milpitas, CA 93-7487 (48) 432-19 FAX: (48) 434-7 TELEX: 499-3977 LT/GP 493 1K REV LINEAR TECHNOLOGY CORPORATION 1993