Solid State Relays for Heaters

New Product Solid State Relays for Heaters Single-phase G3PE Compact, Slim-profile SSRs with Heat Sinks. Models with No Zero Cross for a Wide Range of Applications. RoHS compliant. Models also available with no zero cross Improved surge dielectric strength for output circuits. Compact with a slim profile. Mount to DIN Track or with screws. Certification pending for UL, CSA, and EN (TÜV certification). Refer to Safety Precautions on page 18. Ordering Information List of Models Number of phases Isolation method Operation indicator Rated input voltage Zero cross function Applicable load * 1 A, 1 to 4 VAC 1B DC1-4 Yes A, 1 to 4 VAC B DC1-4 3 A, 1 to 4 VAC 3B DC1-4 4 A, 1 to 4 VAC 4B DC1-4 1 A, 1 to 4 VAC 1BL DC1-4 No A, 1 to 4 VAC BL DC1-4 3 A, 1 to 4 VAC 3BL DC1-4 Single-phase Phototriac 4 A, 1 to 4 VAC 4BL DC1-4 Yes (yellow) 1 to 4 VDC coupler 1 A, to 48 VAC 1B DC1-4 Yes A, to 48 VAC B DC1-4 3 A, to 48 VAC 3B DC1-4 4 A, to 48 VAC 4B DC1-4 1 A, to 48 VAC 1BL DC1-4 No A, to 48 VAC BL DC1-4 3 A, to 48 VAC 3BL DC1-4 4 A, to 48 VAC 4BL DC1-4 * The applicable load current depends on the ambient temperature. For details, refer to Load Current vs. Ambient Temperature in Engineering Data on page 3. Model 1

Single-phase G3PE Specifications Certification UL8 (pending), CS. No.14 (pending), and EN6947-4-3 (pending) Note: The @@B (L) Series has already been certified for the above standards. Ratings Input (at an Ambient Temperature of C) Model @@@B @@@BL Output Item Rated voltage Operating voltage range 1 to 4 VDC 9.6 to 3 VDC Rated input current 7 ma 1 ma Voltage level Must operate voltage Must release voltage 9.6 VDC 1. VDC Item Model * The applicable load current depends on the ambient temperature. For details, refer to Load Current vs. Ambient Temperature in Engineering Data on page 3. Characteristics 1B(L) B(L) 3B(L) 4B(L) 1B(L) B(L) 3B(L) 4B(L) Rated load voltage 1 to 4 VAC (/6 Hz) to 48 VAC (/6 Hz) Load voltage range 7 to 64 VAC (/6 Hz) 18 to 8 VAC (/6 Hz) Applicable load current * Inrush current resistance Permissible I t (reference value) Applicable load (resistive load).1 to 1 A (at 4 C) 1 A (6 Hz, 1cycle).1 to A (at 4 C) A (6 Hz, 1 cycle). to 3 A (at C) 44 A (6 Hz, 1 cycle). to 4 A (at C).1 to 1 A (at 4 C) 1 A (6 Hz, 1 cycle).1 to A (at 4 C) A (6 Hz, 1cycle). to 3 A (at C) 44 A (6 Hz, 1 cycle). to 4 A (at C) 11A s 6A s 1,6A s 18A s 1,3A s 6,6A s 3 kw (at VAC) kw (at VAC) 7 kw (at VAC) 9 kw (at VAC) 6 kw (at 4 VAC) 1 kw (at 4 VAC) 14 kw (at 4 VAC) 18 kw (at 4 VAC) Model G3PE G3PE G3PE G3PE G3PE G3PE G3PE Item -1B -B -3B -4B -1BL -BL -3BL Operate time 1/ of load power source cycle + 1 ms 1 ms Release time 1/ of load power source cycle + 1 ms Output ON voltage drop 1.6 V (RMS) Leakage current 1 ma (at VAC) Insulation resistance 1 MΩ min. (at VDC) Dielectric strength, VAC, /6 Hz for 1 min Vibration resistance 1 to to1 Hz,.37-mm single amplitude (.7-mm double amplitude) (Mounted to DIN track) Shock resistance Destruction: 94 m/s (Mounted to DIN track) Ambient storage temperature 3 to 1 C (with no icing or condensation) Ambient operating temperature 3 to 8 C (with no icing or condensation) Ambient operating humidity 4% to 8% Weight Approx. 4 g Approx. 4 g Approx. 4 g Approx. 4 g G3PE -4BL Model G3PE G3PE G3PE G3PE G3PE G3PE G3PE Item -1B -B -3B -4B -1BL -BL -3BL Operate time 1/ of load power source cycle + 1 ms 1 ms Release time 1/ of load power source cycle + 1 ms Output ON voltage drop 1.8 V (RMS) Leakage current ma (at 48 VAC) Insulation resistance 1 MΩ min. (at VDC) Dielectric strength, VAC, /6 Hz for 1 min Vibration resistance 1 to to1 Hz,.37-mm single amplitude (.7-mm double amplitude) (Mounted to DIN track) Shock resistance Destruction: 94 m/s (Mounted to DIN track) Ambient storage temperature 3 to 1 C (with no icing or condensation) Ambient operating temperature 3 to 8 C (with no icing or condensation) Ambient operating humidity 4% to 8% Weight Approx. 4 g Approx. 4 g Approx. 4 g Approx. 4 g G3PE -4BL

Engineering Data Single-phase G3PE Input Voltage vs. Input Impedance and Input Voltage vs. Input Current @@B @@BL @@B Input impedance (kω) Input current (ma) 1 Ta = C 9 8 7 6 Input current 4 3 Input impedance 1 1 1 3 3 Input voltage (V) @@BL Input impedance (kω) Input current (ma) 1 Ta = C 14 13 1 11 Input current 1 9 8 7 6 4 Input impedance 3 1 1 1 3 3 Input voltage (V) Input impedance (kω) Input current (ma) 1 Ta = C 9 8 7 6 Input current 4 3 Input impedance 1 1 1 3 3 Input voltage (V) Input impedance (kω) Input current (ma) 1 14 13 1 11 1 9 8 7 6 4 3 1 Input impedance Input current Ta = C 1 1 3 3 Input voltage (V) Load Current vs. Ambient Temperature 1B(L), B(L) 1B(L), B(L) 3 1 1 7 B(L) B(L) 1B(L) 1B(L) 3B(L), 4B(L) 3B(L), 4B(L) 4 4 3 3 18 17 14 1 3B(L) 4B(L) 4B(L) 3B(L) 3 4 6 8 1 3 4 6 8 1 Inrush Current Resistance: Non-repetitive Keep the inrush current to below the inrush current resistance value (i.e., below the broken line) if it occurs repetitively. 1B(L), 1B(L) B(L), B(L) 3B(L), 4B(L) 3B(L), 4B(L) Inrush current (A. Peak) 1 Inrush current (A. Peak) 1 Inrush current (A. Peak) 4 3 1 1 1 1 3 1 3 1, 3,, Energized time (ms) 1 3 1 3 1, 3,, Energized time (ms) 1 3 1 3 1, 3,, Energized time (ms) 3

Single-phase G3PE Close Mounting (3 or 8 SSRs) 1B(L) B(L) 3B(L) 4B(L) 1 13 1 1.7 3 Relays 8 Relays 4 4 6 8 1 3 19 1 1 8 7 3 Relays 8 Relays 4 4 6 8 1 4 4 6 8 1 1B(L) B(L) 3B(L) 4B(L) 1 13 1 1.7 3 Relays 8 Relays 3 17 16 1 1 7 6 3 Relays 8 Relays 4 3 8 6 11 1 4 3 8 6 11 1 3 Relays 8 Relays 3 Relays 8 Relays 4 31 3 9 11 1 3 Relays 8 Relays 4 4 6 8 1 4 31 3 9 11 1 3 Relays 8 Relays 4 4 6 8 1 Close Mounting Example 4 4 6 8 1 4 4 6 8 1 4 4 6 8 1 DIN Track 4

Dimensions Single-phase G3PE Note: All units are in millimeters unless otherwise indicated. Solid State Relays 1B(L) B(L) 1B(L) B(L) Two, M4 13 ±. Two, 4.6 dia. 4 1 9 ±. 84 Two, M3. 4. 6.3 Note: Without terminal cover. 13 ±.3 4.6.6 elliptical hole. Note: With terminal cover. 4. Terminal Arrangement/Internal Circuit Diagram @@B @@B 1 1 9 ±.3 (1) (8) (9) Output side circuit Trigger circuit Input Input side Output side circuit Trigger circuit Input Input side Three, 4. dia. or M4 3B(L) 4B(L) 3B(L) 4B(L) Two, M ±. 4.6 dia. 4 Two, M3. 1 9 ±. 84 13. 4.6.6 6 elliptical hole 44. Note: Without terminal cover. Note: With terminal cover. ±.3 Terminal Arrangement/Internal Circuit Diagram @@B @@B 1 1 9 ±.3 (1) (8) (9) Output side circuit Trigger circuit Input Input side Output side circuit Trigger circuit Input Input side Three, 4. dia. or M4

New Product Solid State Contactors for Heaters Three-phase G3PE Compact, Slim-profile SSRs with Heat Sinks. Solid State Contactors for Three-phase Heaters Reduced Installation Work with DIN Track Mounting. RoHS compliant. Improved surge dielectric strength for output circuits. Slim design with 3-phase output and built-in heat sinks. DIN Track mounting types and screw mounting types are available. All DIN Track mounting types mount to DIN Track (applicable DIN Track: TR3-1Fe (IEC 671)). Certification pending for UL, CSA, and EN (TÜV certification). Refer to Safety Precautions on page 18. Ordering Information List of Models Models with Built-in Heat Sinks Number of phases Three-phase Insulation method Phototriac coupler Operation indicator Rated input voltage Zero cross function Yes (yellow) 1 to 4 VDC Yes Type Applicable load *1 DIN track mounting * Screw mounting 1 A, 1 to 4 VAC A, 1 to 4 VAC 3 A, 1 to 4 VAC 4 A, 1 to 4 VAC 1 A, to 48 VAC A, to 48 VAC 3 A, to 48 VAC 4 A, to 48 VAC 1 A, 1 to 4 VAC A, 1 to 4 VAC 3 A, 1 to 4 VAC 4 A, 1 to 4 VAC 1 A, to 48 VAC Number of Model poles 3 1B-3N DC1-4 1B-N DC1-4 3 B-3N DC1-4 B-N DC1-4 3 3B-3N DC1-4 3B-N DC1-4 3 4B-3N DC1-4 4B-N DC1-4 3 1B-3N DC1-4 1B-N DC1-4 3 B-3N DC1-4 B-N DC1-4 3 3B-3N DC1-4 3B-N DC1-4 3 4B-3N DC1-4 4B-N DC1-4 3 1B-3 DC1-4 1B- DC1-4 3 B-3 DC1-4 B- DC1-4 3 3B-3 DC1-4 3B- DC1-4 3 4B-3 DC1-4 4B- DC1-4 3 1B-3 DC1-4 1B- DC1-4 3 B-3 DC1-4 A, to 48 VAC B- DC1-4 3 3B-3 DC1-4 3 A, to 48 VAC 3B- DC1-4 3 4B-3 DC1-4 4 A, to 48 VAC 4B- DC1-4 *1. The applicable load current depends on the ambient temperature. For details, refer to Load Current vs. Ambient Temperature in Engineering Data on page 1. *. The applicable DIN Track is the TR3-1Fe (IEC 671). For details, refer to the mounting information in the Safety Precautions. 6

Three-phase G3PE Models with Externally Attached Heat Sinks Number of phases Three-phase Insulation method Phototriac coupler Operation indicator Rated input voltage * The rated load current depends on the heat sink or radiator that is mounted. It also depends on the ambient temperature. For details, refer to Load Current vs. Ambient Temperature. Accessories (Order Separately) Heat Sink Zero cross function Yes (yellow) 1 to 4 VDC Yes Heat resistance Rth (s-a) ( C/W) Model 1.67 Y9B-P 1.1 Y9B-P1.63 Y9B-P1.43 Y9B-P.36 Y9B-P Type Applicable load * Externally attached heat sinks 1 A, 1 to 4 VAC A, 1 to 4 VAC 3 A, 1 to 4 VAC 4 A, 1 to 4 VAC 1 A, to 48 VAC A, to 48 VAC 3 A, to 48 VAC 4 A, to 48 VAC Number Model of poles 3 1B- DC1-4 1B- DC1-4 3 B- DC1-4 B- DC1-4 3 3B- DC1-4 3B- DC1-4 3 4B- DC1-4 4B- DC1-4 3 1B- DC1-4 1B- DC1-4 3 B- DC1-4 B- DC1-4 3 3B- DC1-4 3B- DC1-4 3 4B- DC1-4 4B- DC1-4 7

Three-phase G3PE Specifications Certification UL8 (pending), CS. No.14 (pending), and EN6947-4-3 (pending) Ratings (at an Ambient Temperature of C) Operating Circuit (All Models) Item Model Same for all models Rated operating voltage 1 to 4 VDC Operating voltage range 9.6 to 3 VDC Rated input current (impedance) 1 ma (4 VDC) Must-operate voltage 9.6 VDC Must-release voltage 1 VDC min. Insulation method Phototriac Operation indicator Yellow LED Main Circuit of Models with Built-in Heat Sinks Model Item 1B- 1B- B- B- 3B- 3B- 4B- 4B- 1B- 1B- B- B- 3B- 3B- 4B- 4B- 3(N) (N) 3(N) (N) 3(N) (N) 3(N) (N) 3(N) (N) 3(N) (N) 3(N) (N) 3(N) (N) Rated load voltage 1 to 4 VAC to 48 VAC Operating voltage range 7 to 64 VAC 18 to 8 VAC Rated load current *1 1 A (at 4 C) A (at 4 C) 3 A (at C) 4 A (at C) 1 A (at 4 C) A (at 4 C) 3 A (at C) 4 A (at C) Minimum load current. A. A Inrush current resistance (peak value) Permissible I t (reference value) Applicable load (resistive load: AC1 class) * 1 A (6 Hz, 1 cycle) A (6 Hz, 1 cycle) 44 A (6 Hz, 1 cycle) *1. The applicable load current depends on the ambient temperature. For details, refer to Load Current vs. Ambient Temperature in Engineering Data on page 1. *. Applicable Load Use the following formula to calculate the maximum total capacity of a heater load for a three-phase balanced load with delta connections. Maximum load capacity = Load current Load voltage 3 Example: 1 A V 3 =,196 W.1 kw Example: 1 A 4 V 3 = 1,39 W 1.3 kw Main Circuit of Models with Externally Attached Heat Sinks Item Model A (6 Hz, 1 cycle) 44 A (6 Hz, 1 cycle) 11A s 6A s 1,6A s 6A s 1,6A s.1 kw (at VAC) 1B- 1B- 8.6 kw (at VAC) B- H B- 1.1 kw (at VAC) 3B- 3B- 1. kw (at VAC) 1. kw (at 48 VAC).7 kw (at 48 VAC) 9. kw (at 48 VAC) Permissible I t (reference value) 11A s 6A s 1,6A s 6A s 1,6A s Applicable load (resistive load: AC1 Refer to Engineering Data on page 1. class) * The rated load current depends on the heat sink or radiator that is mounted. It also depends on the ambient temperature. For details, refer to Load Current vs. Ambient Temperature in Engineering Data on page 1. 4B- 4B- 1B- 1B- B- B- 3B- 3B- 37.4 kw (at 48 VAC) Rated load voltage 1 to 4 VAC to 48 VAC Operating voltage range 7 to 64 VAC 18 to 8 VAC Rated load current * 1 A (at 4 C) A (at 4 C) 3 A (at C) 4 A (at C) 1 A (at 4 C) A (at 4 C) 3 A (at C) 4 A (at C) Minimum load current. A. A Inrush current resistance (peak value) 1 A (6 Hz, 1 cycle) A (6 Hz, 1 cycle) 44 A (6 Hz, 1 cycle) A (6 Hz, 1 cycle) 4B- 44 A (6 Hz, 1 cycle) 4B- 8

Three-phase G3PE Characteristics Models with Built-in Heat Sinks Item Model Operate time Release time Output ON voltage drop Leakage current * Insulation resistance Dielectric strength Vibration resistance Shock resistance Ambient storage temperature Ambient operating temperature Ambient operating humidity Weight 1B- 3(N) 1B- (N) B- 3(N) B- (N) 3B- 3(N) 1/ of load power source cycle + 1 ms 1/ of load power source cycle + 1 ms 3B- (N) 4B- 3(N) 4B- (N) 1B- 3(N) 1B- (N) 1.6 V (RMS) 1.8 V (RMS) B- 3(N) 1 ma (at VAC) ma (at 48 VAC) 1 MΩ min. (at VDC), VAC, /6 Hz for 1 min DIN Track mounting: 1 to to 1 Hz,.17-mm single amplitude (.3-mm double amplitude) Screw mounting: 1 to to 1 Hz,.37-mm single amplitude (.7-mm double amplitude) 94 m/s (reverse mounting: 98 m/s) 3 to 1 C (with no icing or condensation) 3 to 8 C (with no icing or condensation) 4% to 8% Approx. 1. kg Approx. 1.4 kg Approx. 1. kg Approx. 1.6 kg Approx. 1.4 kg Approx.. kg Approx. 1.6 kg Approx. 1. kg Approx. 1.4 kg * The leakage current of phase S will be approximately 3 times larger if the -element model is used. B- (N) Approx. 1. kg 3B- 3(N) Approx. 1.6 kg 3B- (N) Approx. 1.4 kg 4B- 3(N) Approx.. kg 4B- (N) Approx. 1.6 kg Models with Externally Attached Heat Sinks Item Model 1B- 1B- B- B- 3B- 3B- 4B- 4B- 1B- 1B- B- B- 3B- 3B- 4B- 4B- Operate time 1/ of load power source cycle + 1 ms Release time 1/ of load power source cycle + 1 ms Output ON voltage drop 1.6 V (RMS) 1.8 V (RMS) Leakage current * 1 ma (at VAC) ma (at 48 VAC) Insulation resistance 1 MΩ min. (at VDC) Dielectric strength, VAC, /6 Hz for 1 min Vibration resistance 1 to to 1 Hz,.37-mm single amplitude (.7-mm double amplitude) Shock resistance Destruction: 94 m/s Ambient storage temperature 3 to 1 C (with no icing or condensation) Ambient operating temperature 3 to 8 C (with no icing or condensation) Ambient operating humidity 4% to 8% Weight Approx. 3 g * The leakage current of phase S will be approximately 3 times larger if the -element model is used. Heat Sinks Model Y9B-P Y9B-P1 Y9B-P1 Y9B-P Y9B-P Weight Approx. 4 g Approx. 4 g Approx. 6 g Approx. 8 g Approx. 1, g 9

Three-phase G3PE Engineering Data Input Voltage vs. Input Impedance and Input Voltage vs. Input Current @@B-@@ @@B-@@ Input current (ma) Input impedance (kω) 1 9 8 7 6 4 3 1 Input current Input impedance 1 1 3 3 Input voltage (V) Input current (ma) Input impedance (kω) 1 Ta = C 14 13 1 11 1 9 8 Input current 7 6 Input impedance 4 3 1 1 1 3 3 Input voltage (V) Load Current vs. Ambient Temperature Models with Built-in Heat Sinks 1B-3(N), B-3(N) 3B-3(N), 4B-3(N) 1B-(N), B-(N) 3B-(N), 4B-(N) 1B-3(N), B-3(N) 3B-3(N), 4B-3(N) 1B-(N), B-(N) 3B-(N), 4B-(N) 3 1 1 7 B-3(N) B-(N) B-3(N) B-(N) 1B-3(N) 1B-(N) 1B-3(N) 1B-(N) 4 4 3 3 18 14 1 3B-3(N) 3B-(N) 3B-3(N) 3B-(N) 4B-3(N) 4B-(N) 4B-3(N) 4B-(N) 3 4 6 8 1 3 4 6 8 1 Models with Externally Attached Heat Sinks 1B-(-) 3B-(-) B-(-) 4B-(-) 1B-(-) 3B-(-) B-(-) 4B-(-) 1 8 6 B-(-) B-(-) 1 3B-(-) 4B-(-) 3B-(-) 4B-(-) 8 6 4 1B-(-) 1B-(-) 4 3 4 6 8 1 3 4 6 8 1 1

Three-phase G3PE Inrush Current Resistance: Non-repetitive Keep the inrush current to below the inrush current resistance value (i.e., below the broken line) if it occurs repetitively. 1B-3(N)(H) 1B-(N)(H) Inrush current (A. Peak) 1 B-3(N)(H), B-3(N)(H) B-(N)(H), B-(N)(H) 1B-3(N)(H), 1B-(N)(H), Inrush current (A. Peak) 1 3B-3(N)(H), 3B-3(N)(H) 3B-(N)(H), 3B-(N)(H) 4B-3(N)(H), 4B-3(N)(H) 4B-(N)(H), 4B-(N)(H) Inrush current (A. Peak) 4 3 1 1 1 1 3 1 3 1, 3,, 1 3 1 3 1, 3,, 1 3 1 3 1, 3,, Energized time (ms) Heat Sink Area vs. Load Current (4 C and 8 C) B- B- Heat sink area (cm ), 3, 1,, 3, 1, 3 Ambient temperature + 8 C Ambient temperature + 4 C Aluminum plate t = 3. 1 1 3 4 Models with Externally Attached Heat Sinks Heat Resistance Rth (Junction/SSR Back Surface) Heat Resistance of Heat Sinks, 3, Y9B-P.36 Note: If a commercially available heat sink is used, use one that has a heat resistance equal to or lower than a standard OMRON Heat Sink. Heat sink area (cm ) 1,, 3, 1, 3 Model Rth ( C/W) 1B- 1. B-.7 3B-.7 4B-.7 Model Rth ( C/W) Y9B-P 1.67 Y9B-P1 1.1 Y9B-P1.63 Y9B-P.43 Ambient temperature + 8 C Energized time (ms) Ambient temperature + 4 C Aluminum plate t = 3. 1 1 3 4 Energized time (ms) Note: The heat sink area is the combined area of all surfaces of the heat sink that radiate heat. For the B-, when a current of 18 A flows through the SSR at 4 C, the graph shows that a heat sink area of about, cm would be required. Therefore, if the heat sink is square, one side of an aluminum plate in the heat sink must be 36 cm or longer (, (cm )/ = 36 cm (rounded to a whole number)). 11

Three-phase G3PE Dimensions Note: All units are in millimeters unless otherwise indicated. Solid State Relays Models with DIN Track Mounting 1B-3N 1B-N B-N 1B-3N 1B-N B-N Two, R.3 mounting holes. Two, 4.6-dia. mounting holes Four, 8 dia. Two, M3. 4 3. Six, M4 Note: Without terminal cover. 64 8 84. 9 Note: With terminal cover. 1 64±.3 3 19.1 3. 9±.3 Four, 4. dia. or M4 1 1B-3N Terminal Arrangement/Internal Circuit Diagram @B-N 1E-3N @B-N L3/T L3/T L3/T L3/T Models with DIN Track Mounting B-3N 3B-N B-3N 3B-N Two, R.3 mounting holes Two, 4.6-dia. mounting holes Four, 8 dia. Two, M3. 4 84. 1 11 1. Six, M (3-A type) Six, M4 (-A type) 3. Note: Without terminal cover. 64 8 Note: With terminal cover. 64±.3 3 19.1 3. 11±.3 1 Four, 4. dia. or M4 B-3N Terminal Arrangement/Internal Circuit Diagram 3B-N B-3N 3B-N L3/T L3/T L3/T L3/T 1

Three-phase G3PE Models with DIN Track Mounting 3B-3N 4B-N 3B-3N 4B-N Two, 4.6-dia. mounting holes Four, 8 dia. Two, M3. 4 84. 1 13 14 Two, R.3 mounting holes. Six, M 3. Note: Without terminal cover. 64±.3 64 8 Note: With terminal cover. 3 19.1 3. 13±.3 1 Four, 4. dia. or M4 3B-3N Terminal Arrangement/Internal Circuit Diagram 4B-N 3B-3N 4B-N L3/T L3/T L3/T L3/T Models with DIN Track Mounting 4B-3N 4B-3N Two, 4.6-dia. mounting holes Four, 8 dia. Two, M3. Two, R.3 mounting holes 4 84. 1 13 14. Six, M 3. Note: Without terminal cover. 64 8 11 Note: With terminal cover. 64±.3 3 19.1 3. 13±.3 1 Four, 4. dia. or M4 Terminal Arrangement/Internal Circuit Diagram G3PE4B-3N 4B-3N L3/T L3/T 13

Three-phase G3PE Models with Screw Mounting 1B- 1B- 4.6 dia. 4 84. 9 1 DIN Track or screw mounting. 3. Six, M4 Two, M3. Note: Without terminal cover. Two, 4. dia. or M4 8 4.6.6 elliptical hole Note: With terminal cover. 3 3. 19.1 9±.3 ±.3 Terminal Arrangement/Internal Circuit Diagram 1B- 1B- L3/T L3/T Models with Screw Mounting 1B-3 Four, R. B- 1B-3 B- 4 6 8 84.. Two, M3. 3. Six, M4 Note: Without terminal cover. 8 9 1 11. Note: With terminal cover. Four, 4. dia. or M4 19.1 3. 3 For screw mounting only 6±.3 7 1±.3 Terminal Arrangement/Internal Circuit Diagram 1B-3 B- 1B-3 B- L3/T L3/T L3/T L3/T 14

Three-phase G3PE Models with Screw Mounting B-3 3B- B-3 3B- Four, R. 4 84. 9 11. Two, M3.. 3. Six, M (@3B-) Six, M4 (@B-3) Note: Without terminal cover. 8 9 1 11. Note: With terminal cover. Four, 4. dia. or M4 For screw mounting only 19.1 3. 3 9±.3 7 1±.3 B-3 Terminal Arrangement/Internal Circuit Diagram 3B- B-3 3B- L3/T L3/T L3/T L3/T Models with Screw Mounting 3B-3 4B- 3B-3 4B- Four, R. 4 84. 9 13.. 3. Note: Without terminal cover. Two, M3. Six, M 8 11 1 13. Note: With terminal cover. For screw mounting only Four, 4. dia. or M4 19.1 3. 3 9±.3 7 1±.3 Terminal Arrangement/Internal Circuit Diagram 3B-3 4B- 3B-3 4B- L3/T L3/T L3/T L3/T 1

Three-phase G3PE Models with Screw Mounting 4B-3 Four, R. 4B-3 4 84. 1 19. Two, M3. Six, M. 3. Note: Without terminal cover. 8 11 1 13. Note: With terminal cover. For screw mounting only Four, 4. dia. or M4 19.1 3. 3 7 1±.3 Terminal Arrangement/Internal Circuit Diagram 4B-3 4B-3 L3/T L3/T 1±.3 Models with Externally Attached Heat Sinks 1B- Four, 4. dia. Four, 8 dia. 1B- B- B- 3B- 3B- 4B- 4B- 1B-. 3. 1B- B- Note: Without terminal cover. B- 3B- Four, 4. dia. or M4 3B- 4B- 4B- 4 Two, M3. ±.3 8 Note: With terminal cover. Six, M4 (@1B-@H/-@B-@H) Six, M (@3B-@H/-@4B-@H) 8 84. 3 3. 19.1 9 4. dia. 8 dia. ±.3 @B- Terminal Arrangement/Internal Circuit Diagram @B- @B- @B- L3/T L3/T L3/T L3/T 16

Three-phase G3PE Accessories (Order Separately) Heat Sink Y9B-P (Mounts to DIN Track.) For 1B- and 1B- 4.6 dia. Two, 4. dia. or M4 Heat Sink Y9B-P1 For 1B-, B-, 1B-, and B- 1 Four, M4 Four, 4. dia. or M4 8. 9 4.6.6 elliptical hole 1 9±.3 6 8. 6±.3 8 ±.3 Four, R. 11. 1±.3 7 Heat Sink Y9B-P1 For B-, 3B-, B-, and 3B- Heat Sink Y9B-P For 3B-, 4B-, 3B-, and 4B- Heat Sink Y9B-P For 4B- and 4B- 1 1 Four, M4 1 Four, M4 M4-D1 Four, M4 9 11. 9 13. 47.6 1 19. M4-D1 Four, R. 11. Four, R. 1 13. Four, R. 1 13. 7 7 7 Four, 4. dia. or M4 Four, 4. dia. or M4 Four, 4. dia. or M4 9±.3 9±.3 1±.3 1±.3 1±.3 1±.3 17

G3PE Safety Precautions Refer to Safety Precautions for All Solid State Relays.!CAUTION Minor electrical shock may occasionally occur. Do not touch the G3PE terminal section (i.e., currentcarrying parts) while the power is being supplied. Also, always attach the cover terminal. The G3PE may rupture if short-circuit current flows. As protection against accidents due to shortcircuiting, be sure to install protective devices, such as fuses and no-fuse breakers, on the power supply side. Minor electrical shock may occasionally occur. Do not touch the main circuit terminals on the SSR immediately after the power supply has been turned OFF. Shock may result due to the electrical charge stored in the built-in snubber circuit. Minor burns may occasionally occur. Do not touch the SSR or the heat sink while the power is being supplied or immediately after the power supply has been turned OFF. The SSR and heat sink become extremely hot. Precautions for Safe Use OMRON constantly strives to improve quality and reliability. SSRs, however, use semiconductors, and semiconductors may commonly malfunction or fail. In particular, it may not be possible to ensure safety if the SSRs are used outside the rated ranges. Therefore, always use the SSRs within the ratings. When using an SSR, always design the system to ensure safety and prevent human accidents, fires, and social harm in the event of SSR failure. System design must include measures such as system redundancy, measures to prevent fires from spreading, and designs to prevent malfunction. Transport Do not transport the G3PE under the following conditions. Doing so may result in damage, malfunction, or deterioration of performance characteristics. Conditions in which the G3PE may be subject to water. Conditions in which the G3PE may be subject to high temperature or high humidity. Conditions in which the G3PE is not packaged. Operating and Storage Environments Do not use or store the G3PE in the following locations. Doing so may result in damage, malfunction, or deterioration of performance characteristics. Locations subject to rainwater or water splashes. Locations subject to exposure to water, oil, or chemicals. Locations subject to high temperature or high humidity. Do not store in locations subject to ambient storage temperatures outside the range 3 to 1 C. Do not use in locations subject to relative humidity outside the range 4% to 8%. Locations subject to corrosive gases. Locations subject to dust (especially iron dust) or salts. Locations subject to direct sunlight. Locations subject to shock or vibration. Installation and Handling Do not block the movement of the air surrounding the G3PE or heat sink. Abnormal heating of the G3PE may result in shorting failures of the output elements or burn damage. Do not use the G3PE if the heat radiation fins have been bent by being dropped. Doing so may result in malfunction due to a reduction in the heat radiation performance. Do not handle the G3PE with oily or dusty (especially iron dust) hands. Doing so may result in malfunction. Attach a heat sink or radiator when using an SSR. Not doing so may result in malfunction due to a reduction in the heat radiation performance. Installation and Mounting Mount the G3PE in the specified direction. Otherwise excessive heat generated by the G3PE may cause short-circuit failures of the output elements or burn damage. Make sure that there is no excess ambient temperature rise due to the heat generation of the G3PE. If the G3PE is mounted inside a panel, install a fan so that the interior of the panel is fully ventilated. Make sure the DIN track is securely mounted. Otherwise, the G3PE may fall. When mounting the heat sink, do not allow any foreign matter between the heat sink and the mounting surface. Foreign matter may cause malfunction due to a reduction in the heat radiation performance. If the G3PE is mounted directly in a control panel, use aluminum, steel plating, or similar material with a low heat resistance as a substitute for a heat sink. Using the G3PE mounted in wood or other material with a high heat resistance may result in fire or burning due to heat generated by the G3PE. Installation and Wiring Use wires that are suited to the load current. Otherwise, excessive heat generated by the wires may cause burning. Do not use wires with a damaged outer covering. Otherwise, it may result in electric shock or ground leakage. Do not wire any wiring in the same duct or conduit as power or high-tension lines. Otherwise, inductive noise may damage the G3PE or cause it to malfunction. When tightening terminal screws, prevent any non-conducting material from becoming caught between the screws and the tightening surface. Otherwise, excessive heat generated by the terminal may cause burning. Do not use the G3PE with loose terminal screws. Otherwise, excessive heat generated by the wire may cause burning. For the G3PE models with a carry current of 3 A or larger, use M crimp terminals that are an appropriate size for the diameter of the wire. Always turn OFF the power supply before performing wiring. Not doing so may cause electrical shock. Installation and Usage Select a load within the rated values. Not doing so may result in malfunction, failure, or burning. Select a power supply within the rated frequencies. Not doing so may result in malfunction, failure, or burning. The G3PE provides a circuit to prevent photocoupler damage by forcibly arcing the output element for surge voltages applied to the load. The G3PE therefore cannot be used for motor loads. Doing so may result in load motor malfunction. 18

G3PE Precautions for Correct Use The SSR in operation may cause an unexpected accident. Therefore it is necessary to test the SSR under the variety of conditions that are possible. As for the characteristics of the SSR, it is necessary to consider differences in characteristics between individual SSRs. The ratings in this catalog are tested values in a temperature range between 1 C and 3 C, a relative humidity range between % and 8%, and an atmospheric pressure range between 86 and 16 kpa. It will be necessary to provide the above conditions as well as the load conditions if the user wants to confirm the ratings of specific SSRs. Causes of Failure Do not drop the G3PE or subject it to abnormal vibration or shock during transportation or mounting. Doing so may result in deterioration of performance, malfunction, or failure. Tighten each terminal to the torque specified below. Improper tightening may result in abnormal heat generation at the terminal, which may cause burning. Terminals Screw terminal diameter Tightening torque Input terminals M3..9 to 1.18 N m Output M4.98 to 1.47 N m terminals M 1.7 to.4 N m Do not supply overvoltage to the input circuits or output circuits. Doing so may result in failure or burning. Do not use or store the G3PE in the following conditions. Doing so may result in deterioration of performance. Locations subject to static electricity or noise Locations subject to strong electric or magnetic fields Locations subject to radioactivity Mounting The G3PE is heavy. Firmly mount the DIN Track and secure both ends with End Plates for DIN Track mounting models. When mounting the G3PE directly to a panel, firmly secure it to the panel. Screw diameter: M4 Tightening torque:.98 to 1.47 N m Vertical Direction Mounted on a vertical surface Panel Mounted on a horizontal surface Panel Note: Make sure that the load current is % of the rated load current when the G3PE is mounted horizontally. For details on close mounting, refer to the related information under performance characteristics. Mount the G3PE in a direction so that the markings read naturally. The N/-3N (DIN Track mounting models) can be mounted on the following TR3-1Fe (IEC 671) DIN Tracks. Manufacturer Thickness 1. mm.3 mm Schneider AM1-DE --- WAGO 1-114, 1-197 1-118 PHOENIX NS3/1 NS3/1-.3 Wiring When using crimp terminals, refer to the terminal clearances shown below. Output Terminal Section for Three-phase Models 7 mm 13 mm Output Terminal Section for Single-phase Models Input Terminal Section 1-A and -A Models 3-A and 4-A Models 1 mm 13 mm 1.4 mm M4 (1 A, A) 7. mm M3. Make sure that all lead wires are thick enough for the current. For three-element and two-element models, the output terminal will be charged even when the Relay is OFF. Touching the terminal may result in electric shock. To isolate the Relay from the power supply, install an appropriate circuit breaker between the power supply and the Relay. Always turn OFF the power supply before wiring the Unit. Terminal L and terminal T of a -element model are internally connected to each other. Connect terminal L to the ground terminal of the power supply. If terminal L is connected to a terminal other than the ground terminal, cover all the charged terminals, such as heater terminals, to prevent electric shock and ground faults. Fuses Use a quick-burning fuse on the output terminals to prevent accidents due to short-circuiting. Use a fuse with equal or greater performance than those given in the following table. Recommended Fuse Capacity Rated G3PE output current Applicable SSR 1 A G3PE@1B Series A G3PE@B Series 3 A G3PE@3B Series 4 A G3PE@4B Series 1 mm M4 (1 A, A) M (3 A, 4 A) 1 mm 1.9 mm M (3 A, 4 A) Fuse (IEC 669-4) 3 A 63 A 19

G3PE EMC Connection Make EMC connections according to the following figure. Connect a capacitor to the load power supply. The input cable must be no longer than 3 m. Input 3 m G3PE Output Load Recommended Capacitor (Film Capacitor) @@B Series: 1 µf, VAC @@B Series:. µf, VAC EMI This is a Class A product (for industrial environments). In a domestic environment, the G3PE may cause radio interference, in which case the user may be required to take appropriate measures. Noise and Surge Effects If noise or an electrical surge occurs that exceeds the malfunction withstand limit for the G3PE output circuit, the output will turn ON for a maximum of one half cycle to absorb the noise or surge. Confirm that turning the output ON for a half cycle will not cause a problem for the device or system in which the G3PE is being used prior to actual use. The G3PE malfunction withstand limit is shown below. Malfunction withstand limit (reference value): V Note: This value was measured under the following conditions. Noise duration: 1 ns and 1 µs Repetition period: 1 Hz Noise application time: 3 min Mounting Models with Externally Attached Heat Sinks Before attaching an external Heat Sink or Radiator to the Unit, always apply silicone grease, such as Toshiba Silicone's YG66 or Sinetsu Silicone's G746, to the mounting surface to enable proper heat radiation. Tighten the screws to the following torque to secure the Unit and external Heat Sink or Radiator to enable proper heat dissipation. Tightening torque:. N m Mounting to Control Panel The G3PE is heavy. Firmly mount the DIN track and secure both ends with End Plates for DIN-track-mounting models. When mounting the G3PE directly to a panel, firmly secure it to the panel. If the panel is airtight, heat from the SSR will build up inside, which may reduce the current carry ability of the SSR or adversely affect other electrical devices. Be sure to install ventilation holes on the top and bottom of the panel. SSR Mounting Pitch (Panel Mounting) Single-phase Model Mounting direction Vertical Direction Host and slave 8 mm min. SSR Three-phase Models Duct or other object blocking airflow G3PE 1 mm min. G3PE Duct or other object blocking airflow 6 mm min. Between duct and G3PE 6 mm min. Between duct and G3PE 3 mm min. Between duct and G3PE 8 mm min. Host and slave G3PE G3PE Between duct and G3PE 8 mm min. 3 mm min. Duct or other object blocking airflow

G3PE Relationship between the G3PE and Ducts or Other Objects Blocking Airflow Incorrect Example Countermeasure 1 Countermeasure Mounting surface Duct or other object blocking airflow Vertical Direction Mounting surface mm (No more than 1/ the SSR depth is recommended.) Duct Mounting surface Base Duct Airflow SSR SSR SSR If the depth direction of the G3PE is obstructed by ducts, the heat radiation will be adversely affected. Duct Duct Duct Use ducts that have a shallow depth, to provide a sufficient ventilation area. Ventilation Outside the Control Panel Duct or other object blocking airflow If the ducts cannot be made lower, place the G3PE on a metal base so that it is not surrounded by the ducts. Be aware of airflow SSR SSR Ventilation outlet (Axial Fan) SSR Air inlet Note: 1. If the air inlet or air outlet has a filter, clean the filter regularly to prevent it from clogging to ensure an efficient flow of air.. Do not locate any objects around the air inlet or air outlet, otherwise the objects may obstruct the proper ventilation of the control panel. 3. A heat exchanger, if used, should be located in front of the G3PE to ensure the efficiency of the heat exchanger. G3PE Ambient Temperature The rated current of the G3PE is measured at an ambient temperature of 4 C. The G3PE uses a semiconductor to switch the load. This causes the temperature inside the control panel to increase due to heating resulting from the flow of electrical current through the load. The G3PE reliability can be increased by adding a ventilation fan to the control panel to dispel this heat, thus lowering the ambient temperature of the G3PE. (Arrhenius's law suggests that life expectancy is doubled by each 1 C reduction in ambient temperature.) SSR rated current (A) 1 A A 3 A 4 A Required number of.3.39.4.7 fans per SSR Example: For 1 G3PE SSRs with load currents of 1 A,.3 1 =.3 Thus, 3 fans would be required. Note: 1. Size of fans: 9 mm 9 mm, Air volume:.7 m 3 /min, Ambient temperature of control panel: 3 C. If there are other instruments that generate heat in the control panel in addition to SSRs, more ventilation will be required. 3. Ambient temperature: The temperature that will allow the SSR to cool by convection or other means. 1

G3PE Warranty and Application Considerations Read and Understand this Catalog Please read and understand this catalog before purchasing the products. Please consult your OMRON representative if you have any questions or comments. Warranty and Limitations of Liability WARRANTY OMRON's exclusive warranty is that the products are free from defects in materials and workmanship for a period of one year (or other period if specified) from date of sale by OMRON. OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, REGARDING NON-INFRINGEMENT, MERCHANTABILITY, OR FITNESS FOR PARTICULAR PURPOSE OF THE PRODUCTS. ANY BUYER OR USER ACKNOWLEDGES THAT THE BUYER OR USER ALONE HAS DETERMINED THAT THE PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE. OMRON DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR IMPLIED. LIMITATIONS OF LIABILITY OMRON SHALL NOT BE RESPONSIBLE FOR SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS, OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS, WHETHER SUCH CLAIM IS BASED ON CONTRACT, WARRANTY, NEGLIGENCE, OR STRICT LIABILITY. In no event shall the responsibility of OMRON for any act exceed the individual price of the product on which liability is asserted. IN NO EVENT SHALL OMRON BE RESPONSIBLE FOR WARRANTY, REPAIR, OR OTHER CLAIMS REGARDING THE PRODUCTS UNLESS OMRON'S ANALYSIS CONFIRMS THAT THE PRODUCTS WERE PROPERLY HANDLED, STORED, INSTALLED, AND MAINTAINED AND NOT SUBJECT TO CONTAMINATION, ABUSE, MISUSE, OR INAPPROPRIATE MODIFICATION OR REPAIR. Application Considerations SUITABILITY FOR USE OMRON shall not be responsible for conformity with any standards, codes, or regulations that apply to the combination of products in the customer's application or use of the products. Take all necessary steps to determine the suitability of the product for the systems, machines, and equipment with which it will be used. Know and observe all prohibitions of use applicable to this product. NEVER USE THE PRODUCTS FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND THAT THE OMRON PRODUCTS ARE PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM. Disclaimers PERFORMANCE DATA Performance data given in this catalog is provided as a guide for the user in determining suitability and does not constitute a warranty. It may represent the result of OMRON's test conditions, and the users must correlate it to actual application requirements. Actual performance is subject to the OMRON Warranty and Limitations of Liability. CHANGE IN SPECIFICATIONS Product specifications and accessories may be changed at any time based on improvements and other reasons. Consult with your OMRON representative at any time to confirm actual specifications of purchased product. DIMENSIONS AND WEIGHTS Dimensions and weights are nominal and are not to be used for manufacturing purposes, even when tolerances are shown.

OMRON Corporation Industrial Automation Company Control Devices Division H.Q. Strategy Planning Division Shiokoji Horikawa, Shimogyo-ku, Kyoto, 6-83 Japan Tel: (81) 7-344-719/Fax: (81) 7-344-7149 OMRON ELECTRONICS LLC One Commerce Drive Schaumburg, IL 6173-3 U.S.A. Tel: (1) 847-843-79/Fax: (1) 847-843-7787 OMRON ASIA PACIFIC PTE. LTD. No. 438A Alexandra Road # -/8 (Lobby ), Alexandra Technopark, Singapore 119967 Tel: (6) 3-311/Fax: (6) 3-711 Authorized Distributor: Regional Headquarters OMRON (CHINA) CO., LTD. OMRON EUROPE B.V. Room 11, Bank of China Tower, Wegalaan 67-69-13 JD Hoofddorp Yin Cheng Zhong Road, The Netherlands PuDong New Area, Shanghai, 1, China Tel: (31)36-81-3/Fax: (31)36-81-388 Tel: (86) 1-37-/Fax: (86) 1-37- OMRON Industrial Automation Global: www.ia.omron.com OMRON Corporation 8 All Rights Reserved. In the interest of product improvement, specifications are subject to change without notice. Printed in Japan Cat. No. J174-E1-1 88 (88)

Cat. No. J174-E1-1 OMRON Corporation Industrial Automation Company http://www.ia.omron.com/ 8.8 In the interest of product improvement, specifications are subject to change without notice. (c)copyright OMRON Corporation 8 All Rights Reserved.