Configurazione Rete VoIP



Similar documents
Configurazione Rete VoIP

CS3695/M6-109 Lab 8-NPS02 VOIP Sniffing Ver. 8 Rev. 0

Motorola TEAM WSM - Cisco Unified Communications Manager Express (CME) Integration

Lab Configuring Syslog and NTP (Instructor Version)

Lab 5.3.9b Managing Router Configuration Files Using TFTP

Case Study 1: Registering IP Phones with a remote Call

Simple MPLS network topology for Dynamips/Olive

Lab Configure Local AAA on Cisco Router

Lab 8.4.3b Managing Cisco IOS images with ROMMON and TFTP

Managing and Configuring Cisco VoIP Devices

Brest. Backup : copy flash:ppe_brest1 running-config

ADTRAN SBC and Cisco Call Manager Express SIP Trunk Interoperability

Lab 2.1 Configure CME using the CLI and Cisco IP Communicator

Table of Contents. Cisco Using the Cisco IOS Firewall to Allow Java Applets From Known Sites while Denying Others

Planning Maintenance for Complex Networks

How To Configure A Cisco Router With A Cio Router

Configuring Fax Pass-Through

Skills Assessment Student Training (Answer Key)

Integrated Data and Voice Services for ISDN PRI Interfaces on Multiservice Access Routers

Chapter 1: Planning Maintenance for Complex Networks. TSHOOT v6 Chapter , Cisco Systems, Inc. All rights reserved.

TotalCloud Phone System

CCNA Exploration 4.0: ESwitching Basic Switching / Wireless PT Practice SBA. Switch S1 S1#sh ru Building configuration...

Ejemplo de configuración de punta a punta SBC en un Cisco 7600 Series Router

The Cisco IOS Firewall feature set is supported on the following platforms: Cisco 2600 series Cisco 3600 series

Implementing Cisco Unified Communications Voice over IP and QoS v8.0 (CVOICE v8.0) Version: Demo. Page <<1/8>>

Cisco Routers and Switches

Lab 8.4.3a Managing Cisco IOS Images with TFTP

Lab 7: Firewalls Stateful Firewalls and Edge Router Filtering

Configuring a Cisco 2509-RJ Terminal Router

Configuring Basic Broadband Internet Access

Lab Configure Syslog on AP

Lab Creating a Network Map using CDP Instructor Version 2500

LAN-Cell to Cisco Tunneling

- Basic Router Security -

3.1 Connecting to a Router and Basic Configuration

Connecting to the Firewall Services Module and Managing the Configuration

Objectives. Background. Required Resources. CCNA Security

Cisco 2621 Gateway-PBX Interoperability: Lucent/Avaya Definity G3si V7 PBX with Cisco CallManager Using T1 PRI NI-2 for an H.

This document is exclusive property of Cisco Systems, Inc. Permission is granted to print and copy this document for non-commercial distribution and

Configuration Professional: Site to Site IPsec VPN Between Two IOS Routers Configuration Example

Configuring Voice and Data Support on VWIC3s

Proposal for implementation of VoIP at XYZ hospital.

Skills Assessment Student Training Exam

Felix Rohrer. PT Activity 7.5.3: Troubleshooting Wireless WRT300N. Topology Diagram

Lab Configure Basic AP Security through IOS CLI

BRI to PRI Connection Using Data Over Voice

Connect the Host to attach to Fast Ethernet switch port Fa0/2. Configure the host as shown in the topology diagram above.

Configuring Devices for Use with Cisco Configuration Professional (CCP) 2.5

Objectives Understand Cisco IOS system architecture components. Work with the Cisco IOS Command Line Interface (CLI) and common commands.

Lab Load Balancing Across Multiple Paths Instructor Version 2500

ICND IOS CLI Study Guide (CCENT)

ICND1 Lab Guide Interconnecting Cisco Networking Devices Part 1 Version 2.0. Labs powered by

System Components PBX Model. Configuration Tasks

Configuring a Leased Line

Output Interpreter. SHOW RUNNING-CONFIG SECURITY Analysis SHOW RUNNING-CONFIG - FW Analysis. Back to top

and 2, implemented With Cisco Unified Border Control Element (CUBE)

Consolidated Packages and SubPackages Management

Chapter 8 Lab B: Configuring a Remote Access VPN Server and Client

Table of Contents. Cisco How to Download a Software Image to a Cisco 2600 via TFTP Using the tftpdnld ROMmon Command

Network Security Knowledge is Everything! Network Operations

Configuring System Message Logging

- The PIX OS Command-Line Interface -

Lab 3.5.1: Basic VLAN Configuration (Instructor Version)

PT Activity: Configure Cisco Routers for Syslog, NTP, and SSH Operations

Network Security 2. Module 6 Configure Remote Access VPN

Note: This case study utilizes Packet Tracer. Please see the Chapter 5 Packet Tracer file located in Supplemental Materials.

Enabling Management Protocols: NTP, SNMP, and Syslog

Cisco Configuration Professional Quick Start Guide

Using LiveAction with Cisco Secure ACS (TACACS+ Server)

Remote Access VPN Business Scenarios

Basic Configuration of the Cisco Series Internet Router

Validated Integrations: CUCM 10.x with xic version 4.0 SU-6 (support included for all 4.0 SU s) Version 4.08

Applicazioni Telematiche

Lab 5-5 Configuring the Cisco IOS DHCP Server

Configuring the Cisco Secure PIX Firewall with a Single Intern

Table of Contents. Cisco How to Download a Software Image to a Cisco 2600 through TFTP Using the tftpdnld ROMmon Command

Basic Router Configuration

Telnet, Console and AUX Port Passwords on Cisco Routers Configuration Example

- Advanced IOS Functions -

Cisco IOS Voice Gateway PBX Interoperability: Avaya 8500 Communications Manager 2.1 to T1 QSIG with H.323

Module 6 Configure Remote Access VPN

Lab: Basic Router Configuration

Chapter 4: Lab A: Configuring CBAC and Zone-Based Firewalls

Deployment Guidelines for QoS Configuration in DSL Environment

Lab Introductory Lab 1 - Getting Started and Building Start.txt

Lab 5.5 Configuring Logging

Basic Router Configuration Using Cisco Configuration Professional

LAB Configuring NAT. Objective. Background/Preparation

Configuring the MNLB Forwarding Agent

Using a Sierra Wireless AirLink Raven X or Raven-E with a Cisco Router Application Note

One-Step Lockdown with Cisco SDM

P and FTP Proxy caching Using a Cisco Cache Engine 550 an

LAB MANUAL for Computer Network

Center for Internet Security Gold Standard Benchmark for Cisco IOS

Configuring Modem Transport Support for VoIP

Table of Contents. Cisco Configuring IPSec Cisco Secure VPN Client to Central Router Controlling Access

APNIC Members Training Course Security workshop. 2-4 July, Port Vila Vanuatu. In conjunction with PACNOG 4

Quality of Service and Bandwidth Management Configuration

Transcription:

Configurazione Rete VoIP 1x CISCO 7940G 1x CISCO 3725 with cme-full-7.0.0.1.tar 1x CISCO IP Communicator Startup Config router CISCO 3725 Procedura Operativa: Topologia di rete Operazioni preliminary sul CISCO 3725 Router 3725 Cisco IOS Software, 3700 Software (C3725-ADVENTERPRISEK9_SNA-M), Version 12.4(25d), RELEASE SOFTWARE (fc1) with 64Mbit di Flash Format flash: del Router R1#copy run flash: Destination filename [r1-confg]? Erase flash: before copying? [confirm]n Verifying checksum... OK (0x6C65) 901 bytes copied in 2.980 secs (302 bytes/sec) R1#format flash: Format operation may take a while. Continue? [confirm] Format operation will destroy all data in "flash:". Continue? [confirm] Current Low End File System flash card in flash will be formatted into DOS File System flash card Continue? [confirm] Ing. Nicola Cappuccio 1

Format: Drive communication & 1st Sector Write OK... Writing Monlib sectors....... Monlib write complete Format: All system sectors written. OK... Format: Total sectors in formatted partition: 130911 Format: Total bytes in formatted partition: 67026432 Format: Operation completed successfully. Format of flash complete interfaces Fastethernet 0/0 192.168.100.1/24 Operazioni preliminari sul PC Abilitare un interfaccia di loopback 192.168.100.2/24 e collegare via Ethernet il pc ed il 7940G Abilitare il server TFTP sull indirizzo di loopback 192.168.100.2/24 Download via TFTP del cme-full-7.0.0.1.tar from PC to CISCO Router router#archive tar /xtract tftp://<local host>/cme-full-7.0.0.1.tar flash: Configurare DHCP su CISCO 3725 Abilititare server dhcp router# configure terminal router (config)# ip dhcp excluded-address 192.168.100.1 192.168.100.10 router (config)# ip dhcp pool VOICE_SCOPE router (dhcp-config)# network 192.168.100.0 255.255.255.0 router (dhcp-config)# default-router 192.168.100.1 router (dhcp-config)# option 150 ip 192.168.100.1 router (dhcp-config)# dns-server 4.2.2.2 Abilitare il debug router#debug ip dhcp server events Ing. Nicola Cappuccio 2

Configurare I Servizi Telefonici router # dir flash:/phone/7940-7960 Directory of flash:/phone/7940-7960/ Laboratorio 24/11/2014 98 -rw- 129824 May 12 2008 21:33:56-07:00 P00308000500.bin 99 -rw- 458 May 12 2008 21:33:56-07:00 P00308000500.loads 100 -rw- 705536 May 12 2008 21:34:00-07:00 P00308000500.sb2 101 -rw- 130228 May 12 2008 21:34:00-07:00 P00308000500.sbn 129996800 bytes total (28583936 bytes free) router # configure terminal Enter configuration commands, one per line. End with CNTL/Z. router (config)# tftp-server flash:/phone/7940-7960/p00308000500.bin alias P00308000500.bin router (config)# tftp-server flash:/phone/7940-7960/p00308000500.loads alias P00308000500.loads router (config)# tftp-server flash:/phone/7940-7960/p00308000500.sb2 alias P00308000500.sb2 router (config)# tftp-server flash:/phone/7940-7960/p00308000500.sbn alias P00308000500.sbn router (config)# telephony-service router (config-telephony)# ip source-address 192.168.100.1 router(config-telephony)#create cnf-files router (config-telephony)#do sh flash -#- --length-- -----date/time------ path 1 0 Mar 1 2002 01:58:18 +01:00 bacdprompts. 46 0 Mar 1 2002 02:00:12 +01:00 phone 47 0 Mar 1 2002 02:00:12 +01:00 phone/7940-7960 48 129824 Mar 1 2002 02:00:16 +01:00 phone/7940-7960/p00308000500.bin 49 458 Mar 1 2002 02:00:16 +01:00 phone/7940-7960/p00308000500.loads 50 705536 Mar 1 2002 02:00:42 +01:00 phone/7940-7960/p00308000500.sb2 51 130228 Mar 1 2002 02:00:46 +01:00 phone/7940-7960/p00308000500.sbn Ing. Nicola Cappuccio 3

. router(config-telephonyr)#load 7960-7940 P00308000500 Updating CNF files CNF files updating complete router(config-telephonyr)#reset sequence-all router(config-telephony)#create cnf-files router(config-telephony)#reset sequence-all router(config-telephony)#exit router (config-telephony)# max-ephones? <1-30> Maximum phones to support router (config-telephony)# max-ephones 10 router (config-telephony)# max-dn? <1-150> Maximum directory numbers supported <cr> router (config-telephony)# max-dn 10 router (config)#ephone-dn 1 router (config-ephone-dn)#number 1000 router (config-ephone-dn)#exit router (config)#ephone-dn 2 router (config-ephone-dn)#number 2000 router (config-ephone-dn)#exit router # show ephone */restituisce la lista degli ephone presenti sulla rete con il mac-address */associazione IP-Phone Numeri e Linee router (config)# ephone 1 router (config-ephone)# mac-address XXXX.XXXX.XXXX router (config-ephone)# button 1:1 router (config-ephone)# restart router (config-ephone)# exit router (config)# ephone 2 Ing. Nicola Cappuccio 4

router (config-ephone)# mac-address YYYY.YYYY.YYYY router (config-ephone)# button 1:1 router (config-ephone)# restart router (config-ephone)# exit Setting the Clock of a Cisco Device with NTP router #configure terminal router (config)#ntp server 193.204.114.232 router (config)#clock timezone ITALY +1 router (config)#ntp master Startup-config 3725 Last configuration change at 02:08:08 ITALY Fri Mar 1 2002 NVRAM config last updated at 02:27:07 ITALY Fri Mar 1 2002 version 12.4 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption hostname R1 boot-start-marker boot-end-marker no aaa new-model memory-size iomem 5 clock timezone ITALY 1 no ip icmp rate-limit unreachable ip cef no ip dhcp use vrf connected ip dhcp excluded-address 192.168.100.1 192.168.100.10 ip dhcp pool VOICE_SCOPE network 192.168.100.0 255.255.255.0 default-router 192.168.100.1 option 150 ip 192.168.100.1 no ip domain lookup ip auth-proxy max-nodata-conns 3 ip admission max-nodata-conns 3 Ing. Nicola Cappuccio 5

ip tcp synwait-time 5 ip ssh version 1 interface FastEthernet0/0 ip address 192.168.100.1 255.255.255.0 duplex auto speed auto interface FastEthernet0/1 no ip address shutdown duplex auto speed auto ip forward-protocol nd no ip http server no ip http secure-server no cdp log mismatch duplex tftp-server flash:/phone/7940-7960/p00308000500.bin alias P00308000500.bin tftp-server flash:/phone/7940-7960/p00308000500.loads alias P00308000500.loads tftp-server flash:/phone/7940-7960/p00308000500.sb2 alias P00308000500.sb2 tftp-server flash:/phone/7940-7960/p00308000500.sbn alias P00308000500.sbn control-plane Ing. Nicola Cappuccio 6

telephony-service load 7960-7940 P00308000500 max-ephones 10 max-dn 10 ip source-address 192.168.100.1 port 2000 create cnf-files version-stamp 7960 Mar 01 2002 01:38:27 max-conferences 8 gain -6 ephone-dn 1 number 1000 ephone-dn 2 number 2000 ephone 1 mac-address 001F.6C80.7F50 button 1:1 ephone 2 mac-address 0200.4C4F.4F50 button 1:2 line con 0 exec-timeout 0 0 privilege level 15 logging synchronous line aux 0 exec-timeout 0 0 privilege level 15 logging synchronous line vty 0 4 login ntp master 1 ntp server 193.204.114.232 end Application Note 7940G direttamente connesso alla porta Ethernet del PC. Disattivare windows firewall Ing. Nicola Cappuccio 7