Ejemplo de configuración de punta a punta SBC en un Cisco 7600 Series Router
|
|
|
- Johnathan Cole
- 10 years ago
- Views:
Transcription
1 Ejemplo de configuración de punta a punta SBC en un Cisco 7600 Series Router Descargue este capítulo Ejemplo de configuración de punta a punta SBC en un Cisco 7600 Series Router Descargue el libro completo Guía de configuración de controlador de la frontera de la sesión de los Cisco 7600 Series Router (PDF - 9 MB) Feedback Contenidos Ejemplo de configuración de punta a punta SBC en un Cisco 7600 Series Router Ejemplo de configuración de punta a punta SBC en un Cisco 7600 Series Router Esta sección contiene una configuración completa SBC del Cisco 7600 Series Router UUT1# show run Building configuration... Current configuration : 5863 bytes upgrade fpd auto version 12.2 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption service internal service counters max age 10 hostname UUT1 boot-start-marker boot system disk0:c7600s72033-adventerprisek9-mz sr boot device module 3 disk0:c76-sbck9-mzg.devtest_26nov07.bin boot device module 4 disk0:c76-sbck9-mzg.devtest_26nov07.bin boot-end-marker vrf definition vpn1 rd 55:1111
2 address-family ipv4 exit-address-family vrf definition vpn2 rd 55:1112 address-family ipv4 exit-address-family enable password cisco no aaa new-model svclc multiple-vlan-interfaces svclc module 3 vlan-group 100,200,300,400,500 svclc module 4 vlan-group 100,200,300,400,500 svclc vlan-group svclc vlan-group svclc vlan-group svclc vlan-group svclc vlan-group ip subnet-zero no ip domain lookup ip host abrick vtp domain sbc vtp mode transparent mls ip multicast flow-stat-timer 9 mls flow ip interface-full no mls flow ipv6 no mls acl tcam share-global mls cef error action reset multilink bundle-name authenticated spanning-tree mode pvst spanning-tree extend system-id diagnostic cns publish cisco.cns.device.diag_results diagnostic cns subscribe cisco.cns.device.diag_commands redundancy
3 main-cpu auto-sync running-config mode sso vlan internal allocation policy ascending vlan access-log ratelimit 2000 vlan 23,77,88,99 interface Loopback0 ip address interface GigabitEthernet1/1 description ''Connected to CAT Fa 0/7'' ip address ip router isis interface GigabitEthernet1/2 description ''Connected to CAT Fa 0/8'' ip address ip router isis interface GigabitEthernet1/3 description ''Connected to CAT Fa 0/13 vlan919'' vrf forwarding vpn1 ip address interface GigabitEthernet1/4 description ''Connected to CAT Fa 0/14 vlan920'' vrf forwarding vpn2 ip address interface GigabitEthernet1/5 no ip address shutdown interface GigabitEthernet5/2 description ''Connected to CAT FA0/3 ip address media-type rj45
4 interface GigabitEthernet6/1 no ip address shutdown interface GigabitEthernet6/2 description ''Connected to CAT FA 0/4'' no ip address media-type rj45 interface Vlan1 no ip address shutdown interface Vlan23 no ip address logging event link-status logging event nfas-status interface Vlan77 vrf forwarding vpn2 ip address interface Vlan88 ip address ip router isis logging event link-status logging event nfas-status interface Vlan99 vrf forwarding vpn1 ip address router isis net ip classless ip route ip route
5 no ip http server no ip http secure-server access-list 1 deny access-list 1 permit any control-plane line con 0 exec-timeout 0 0 line vty 0 4 exec-timeout 0 0 password cisco login transport input lat pad mop udptn telnet rlogin ssh nasi acercon scheduler runtime netinput 300 end UUT1# ACE Configuration ================= ACE-101-UUT1-2/Admin# show run Generating configuration... login timeout 0 hostname ACE-101-UUT1-2 boot system image:c76-sbck9-mzg.devtest_26nov07.bin
6 clock timezone standard BST timeout xlate interface vlan 88 ip address alias peer ip address no shutdown ft interface vlan 23 ip address peer ip address no shutdown ft peer 1 heartbeat interval 300 heartbeat count 10 ft-interface vlan 23 query-interface vlan 88 ft group 1 peer 1 priority 125 peer priority 225 associate-context Admin inservice ip route ip route ip route context vpn1 allocate-interface vlan 99 context vpn2
7 allocate-interface vlan 77 ft group 2 peer 1 priority 60 peer priority 70 associate-context vpn1 inservice ft group 3 peer 1 priority 60 peer priority 70 associate-context vpn2 inservice username admin password 5 $1$faXJEFBj$TJR1Nx7sLPTi5BZ97v08c/ role Admin domain default-domain username www password 5 $1$UZIiwUk7$QMVYN1JASaycabrHkhGcS/ role Admin domain de fault-domain sbc SBC-CONFIG-SAMPLE sbe sbe media-gateway ipv codecs m=audio 1234 RTP/AVP ,a=rtpmap:2 G726-32/8000,a=rtpmap:8 PCMA/8000,a=rtpmap:0 PCMU/8000,a=rtpmap:18 G729/8000 transcoder control address h248 index 0 ipv port 2944 transport udp sip method-profile default pass-body adjacency sip SIP-GW-1A nat force-off preferred-transport udp redirect-mode pass-through authentication nonce timeout 300 signaling-address ipv signaling-port 5060 remote-address ipv
8 signaling-peer signaling-peer-port 5060 dbe-location-id account SIP-CUSTOMER-1 reg-min-expiry 3000 attach adjacency sip SIP-GW-1B nat force-off preferred-transport udp redirect-mode pass-through authentication nonce timeout 300 signaling-address ipv signaling-port 5060 remote-address ipv signaling-peer signaling-peer-port 5060 dbe-location-id account SIP-CUSTOMER-2 reg-min-expiry 3000 attach sip inherit profile preset-standard-non-ims retry-limit 3 call-policy-set 1 first-call-routing-table ROUTE-ON-DEST-NUM rtg-dst-address-table ROUTE-ON-DEST-NUM entry 1 action complete dst-adjacency SIP-GW-1B match-address 6661 prefix entry 2 action complete dst-adjacency SIP-GW-1A match-address 7771 prefix
9 complete active-call-policy-set 1 sip max-connections 2 sip timer tcp-idle-timeout tls-idle-timeout udp-response-linger-period udp-first-retransmit-interval 500 udp-max-retransmit-interval 4000 invite-timeout 180 h323 ras timeout arq 5000 ras retry arq 2 ras timeout brq 3000 ras retry brq 2 ras timeout drq 3000 ras retry drq 2 ras timeout grq 5000 ras retry grq 2 ras timeout rrq 3000 ras retry rrq 2 ras rrq ttl 60 ras timeout urq 3000 ras retry urq 1 h225 timeout proceeding h225 timeout establishment h225 timeout setup 4000 ras rrq keepalive h323 adjacency timeout blacklist global redirect-limit 2 deact-mode normal
10 dbe media-address ipv vrf vpn2 media-address ipv media-address ipv vrf vpn1 media-timeout 90 deact-mode normal activate Cisco Systems Inc. Todos los Derechos Reservados. Fecha de Generación del PDF: 2 Agosto
Juniper Networks WX Series Large. Integration on Cisco
APPLICATION NOTE Juniper Networks WX Series Large Deployment with WCCP Off-Path Integration on Cisco Integrating Multiple Juniper Networks WX Series Application Acceleration Platforms into a Cisco Infrastructure
Brest. Backup : copy flash:ppe_brest1 running-config
Brest Backup : copy flash:ppe_brest1 running-config Cisco SF300-08 Mise en place des services : - Serveurs : 10.3.50.0/24 VLAN 2 (port 1) - DSI : 10.3.51.0/24 VLAN 3 (port 2) - Direction : 10.3.52.0/24
Lab Configuring Syslog and NTP (Instructor Version)
(Instructor Version) Instructor Note: Red font color or Gray highlights indicate text that appears in the instructor copy only. Topology Addressing Table Objectives Device Interface IP Address Subnet Mask
CS3695/M6-109 Lab 8-NPS02 VOIP Sniffing Ver. 8 Rev. 0
Background For this lab, we will be analyzing some Wireshark capture files that were captured using the ARP Poisoning technique on Cisco VIOP (Voice Over IP) phones As this lab took special equipment (i.e.
Simple MPLS network topology for Dynamips/Olive
Simple MPLS network topology for Dynamips/Olive R1 version 12.4 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption hostname R1 boot-start-marker
How To Configure A Cisco Router With A Cio Router
CHAPTER 1 This chapter provides procedures for configuring the basic parameters of your Cisco router, including global parameter settings, routing protocols, interfaces, and command-line access. It also
CCNA Exploration 4.0: ESwitching Basic Switching / Wireless PT Practice SBA. Switch S1 S1#sh ru Building configuration...
CCNA Exploration 4.0: ESwitching Basic Switching / Wireless PT Practice SBA Switch S1 S1#sh ru Building configuration... Current configuration : 1639 bytes version 12.2 no service timestamps log datetime
Felix Rohrer. PT Activity 7.5.3: Troubleshooting Wireless WRT300N. Topology Diagram
Felix Rohrer PT Activity 7.5.3: Troubleshooting Wireless WRT300N Topology Diagram All contents are Copyright 1992 2007 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.
Lab 6.1.3 Configure Local AAA on Cisco Router
Lab 6.1.3 Configure Local AAA on Cisco Router Objective Scenario Topology In this lab, the students will complete the following tasks: Securing and testing access to the privileged EXEC, VTY, and console
Configuring Fax Pass-Through
Configuring Fax Pass-Through This chapter describes the configuration of fax pass-through. With fax pass-through, modulated fax information from the PSTN is passed in-band over a voice speech path in an
Configuration Professional: Site to Site IPsec VPN Between Two IOS Routers Configuration Example
Configuration Professional: Site to Site IPsec VPN Between Two IOS Routers Configuration Example Document ID: 113337 Contents Introduction Prerequisites Requirements Components Used Conventions Configuration
Lab 7: Firewalls Stateful Firewalls and Edge Router Filtering
Lab 7: Firewalls Stateful Firewalls and Edge Router Filtering 7.1 Details Aim: Rich Macfarlane The aim of this lab is to introduce the concepts of stateful firewalls, using Cisco Contextbased Access Control
Configurazione Rete VoIP
Configurazione Rete VoIP 1x CISCO 7940G 1x CISCO 3725 with cme-full-7.0.0.1.tar 1x CISCO IP Communicator Startup Config router CISCO 3725 Procedura Operativa: Topologia di rete Operazioni preliminary sul
P and FTP Proxy caching Using a Cisco Cache Engine 550 an
P and FTP Proxy caching Using a Cisco Cache Engine 550 an Table of Contents HTTP and FTP Proxy caching Using a Cisco Cache Engine 550 and a PIX Firewall...1 Introduction...1 Before You Begin...1 Conventions...1
Configurazione Rete VoIP
Configurazione Rete VoIP 1x CISCO 7940G 1x CISCO 3725 with cme-full-7.0.0.1.tar 1x CISCO IP Communicator Startup Config router CISCO 3725 Procedura Operativa: Topologia di rete Operazioni preliminary sul
Skills Assessment Student Training (Answer Key)
CCNA: Connecting Networks Skills Assessment Student Training (Answer Key) Instructor Note: Red font color or Gray highlights indicate text that appears in the instructor copy only. Topology Assessment
Configuring a Cisco 2509-RJ Terminal Router
created by: Rainer Bemsel Version 1.0 Dated: Dec/08/2012 For my Cisco LAB, I ve purchased a used Cisco 2509-RJ with RJ45-RJ45 roll-over cables. This TechTip shows my configuration setup, so you can easily
Configuring Voice and Data Support on VWIC3s
First Published: July 21, 2010, OL-22847-01 This module describes how to configure voice and data support on the next generation of voice/wan Interface Cards (VWICs) also known as VWIC3s. The following
Table of Contents. Cisco Using the Cisco IOS Firewall to Allow Java Applets From Known Sites while Denying Others
Cisco IOS Firewall to Allow Java Applets From Known Sites w Table of Contents Using the Cisco IOS Firewall to Allow Java Applets From Known Sites while Denying Others...1 Introduction...1 To Deny Java
Session Border Controller
CHAPTER 13 This chapter describes the level of support that Cisco ANA provides for (SBC), as follows: Technology Description, page 13-1 Information Model Objects (IMOs), page 13-2 Vendor-Specific Inventory
and 2, implemented With Cisco Unified Border Control Element (CUBE)
www.xo.com XO SIP Service Customer Configuration Guide for Cisco Unified Communications Manager (CUCM) 8.0.3 XO SIP Packages 1 and 2, implemented With Cisco Unified Border Control Element (CUBE) 1 PRODUCT
Configuring the Cisco Secure PIX Firewall with a Single Intern
Configuring the Cisco Secure PIX Firewall with a Single Intern Table of Contents Configuring the Cisco Secure PIX Firewall with a Single Internal Network...1 Interactive: This document offers customized
Remote Access VPN Business Scenarios
CHAPTER 4 This chapter explains the basic tasks for configuring an IP-based, remote access Virtual Private Network (VPN) on a Cisco 7200 series router. In the remote access VPN business scenario, a remote
The Cisco IOS Firewall feature set is supported on the following platforms: Cisco 2600 series Cisco 3600 series
Cisco IOS Firewall Feature Set Feature Summary The Cisco IOS Firewall feature set is available in Cisco IOS Release 12.0. This document includes information that is new in Cisco IOS Release 12.0(1)T, including
Motorola TEAM WSM - Cisco Unified Communications Manager Express (CME) Integration
Motorola TEAM WSM - Cisco Unified Communications Manager Express (CME) Integration Summary This setup covers the of the TEAM VoWLAN solution with a Cisco Communications Manager Express 4.1 +. This integration
Configuring a Leased Line
CHAPTER 4 Configuring a Leased Line The configuration in this chapter describes how to configure a Cisco 1700 router for IP and IPX over a synchronous serial line. Before You Begin The configuration in
Configuring Modem Transport Support for VoIP
Configuring Modem Transport Support for VoIP This chapter explains how to configure modem transport support for Voice over IP (VoIP) and contains the following sections: Modem Transport Support Overview,
Lab 11.5.6.1 Configure Syslog on AP
Lab 11.5.6.1 Configure Syslog on AP Estimated Time: 25 minutes Number of Team Members: Students will work in teams of two. Objective In this lab, students will configure and use syslog logging to monitor
SIP Trunking Configuration Guide for Cisco Unified Communications Manager (CUCM) Version 9.0.1.11005-1 with Cisco Unified Border Element (CUBE)
SIP Trunking Configuration Guide for Cisco Unified Communications Manager (CUCM) Version 9.0.1.11005-1 with Cisco Unified Border Element (CUBE) Table of Contents Introduction... 3 Executive Summary..3
How To Configure A Cisco Vpn On A Cell Phone With A Pkv On A Safd On A Pv On An Asda On A Network With A Network On A Pc Or Ipv On The Ipv (Svv
CHAPTER 17 The Cisco VPN Client for Cisco Unified IP Phones adds another option for customers attempting to solve the remote telecommuter problem by complementing other Cisco remote telecommuting offerings.
login timeout 30 access list ALL line 20 extended permit ip any any port 9053 interval 15 passdetect interval 30
logging enable logging console 4 logging timestamp logging trap 5 logging buffered 4 logging device id hostname logging host 10.0.128.240 udp/514 format emblem logging host 10.0.143.24 udp/514 login timeout
Cisco Unified Communications Manager 10.5.2 with Cisco Unified Border Element [CUBE 11.0.0 IOS-XE 3.15] on ISR 4K using SIP
![Cisco Unified Communications Manager 10.5.2 with Cisco Unified Border Element [CUBE 11.0.0 IOS-XE 3.15] on ISR 4K using SIP](/thumbs/25/4987291.jpg "Cisco Unified Communications Manager 10.5.2 with Cisco Unified Border Element [CUBE 11.0.0 IOS-XE 3.15] on ISR 4K using SIP")
Verizon SIP Trunking: Cisco Unified Communications Manager 10.5.2 with Cisco Unified Border Element [CUBE 11.0.0 IOS-XE 3.15] on ISR 4K using SIP JULY 24, 2015 Page 1 of 63 Table of Contents Introduction...
Configuring the MNLB Forwarding Agent
CHAPTER 3 Configuring the MNLB Forwarding Agent This chapter describes how to configure a Cisco router as an MNLB Forwarding Agent to operate in conjunction with a Cisco LocalDirector serving as Services
642 523 Securing Networks with PIX and ASA
642 523 Securing Networks with PIX and ASA Course Number: 642 523 Length: 1 Day(s) Course Overview This course is part of the training for the Cisco Certified Security Professional and the Cisco Firewall
Lab 8: Confi guring QoS
Lab 8: Objective Implement QoS, mark traffi c, and display and interpret QoS output. Lab Topology For this lab, your network design will include two pods of devices. You will be responsible for confi guring
TotalCloud Phone System
TotalCloud Phone System Cisco SF 302-08P PoE VLAN Configuration Guide Note: The below information and configuration is for deployment of the Cbeyond managed switch solution using the Cisco 302 8 port Power
Firewall Stateful Inspection of ICMP
The feature addresses the limitation of qualifying Internet Control Management Protocol (ICMP) messages into either a malicious or benign category by allowing the Cisco IOS firewall to use stateful inspection
Network Simulator Lab Study Plan
The CCNA 640-802 Network Simulator has 300 lab exercises, organized both by type (Skill Builder, Configuration Scenario, Troubleshooting Scenario, and Subnetting Exercise) and by major topic within each
Lab 5.3.9b Managing Router Configuration Files Using TFTP
Lab 5.3.9b Managing Router Configuration Files Using TFTP Device Host Name Interface IP Address Subnet Mask R1 R1 Fast Ethernet 0/0 172.17.0.1 255.255.0.0 Objectives Download and install TFTP server software.
Virtual Private Network Setup
This chapter provides information about virtual private network setup. Virtual Private Network, page 1 Devices Supporting VPN, page 2 Set Up VPN Feature, page 2 Complete Cisco IOS Prerequisites, page 3
Lab 8.3.1.2 Configure Basic AP Security through IOS CLI
Lab 8.3.1.2 Configure Basic AP Security through IOS CLI Estimated Time: 30 minutes Number of Team Members: Students will work in teams of two. Objective In this lab, the student will learn the following
Case Study 1: Registering IP Phones with a remote Call
Case Study 1: Registering IP Phones with a remote Call Manager Objectives Place calls from IP Phones under R1 to IP Phones under R2 Place calls from any IP Phone (under R1 and under R2) to the regular
Troubleshooting the Firewall Services Module
CHAPTER 25 This chapter describes how to troubleshoot the FWSM, and includes the following sections: Testing Your Configuration, page 25-1 Reloading the FWSM, page 25-6 Performing Password Recovery, page
BRI to PRI Connection Using Data Over Voice
BRI to PRI Connection Using Data Over Voice Document ID: 14962 Contents Introduction Prerequisites Requirements Conventions Background Information Configure Network Diagram Configurations Verify Troubleshoot
ICND1-100-101 IOS CLI Study Guide (CCENT)
ICND1-100-101 IOS CLI Study Guide (CCENT) Hostname: 2. hostname SW1 SWITCH CONFIGURATION Mgmt IP: 2. interface vlan 1 3. ip address 10.0.0.2 4. no shut Gateway: 2. ip default-gateway 10.0.0.1 Local User/Pwd:
ADTRAN SBC and Cisco Call Manager Express SIP Trunk Interoperability
6AOSSG0007-42A March 2013 Interoperability Guide ADTRAN SBC and Cisco Call Manager Express SIP Trunk Interoperability This guide describes an example configuration used in testing the interoperability
Using LiveAction with Cisco Secure ACS (TACACS+ Server)
LiveAction Application Note Using LiveAction with Cisco Secure ACS (TACACS+ Server) September 2012 http://www.actionpacked.com Table of Contents 1. Introduction... 1 2. Cisco Router Configuration... 2
Cisco NetFlow Security Event Logging Guide: Cisco ASA 5580 Adaptive Security Appliance and Cisco NetFlow Collector
Cisco NetFlow Security Event Logging Guide: Cisco ASA 5580 Adaptive Security Appliance and Cisco NetFlow Collector Cisco ASA Software Version 8.1 for Cisco ASA 5580 Adaptive Security Appliance has introduced
Skills Assessment Student Training Exam
Skills Assessment Student Training Exam Topology Assessment Objectives Part 1: Initialize Devices (8 points, 5 minutes) Part 2: Configure Device Basic Settings (28 points, 30 minutes) Part 3: Configure
Troubleshooting the Firewall Services Module
25 CHAPTER This chapter describes how to troubleshoot the FWSM, and includes the following sections: Testing Your Configuration, page 25-1 Reloading the FWSM, page 25-6 Performing Password Recovery, page
PT Activity: Configure Cisco Routers for Syslog, NTP, and SSH Operations
PT Activity: Configure Cisco Routers for Syslog, NTP, and SSH Operations Instructor Version Topology Diagram Addressing Table Device Interface IP Address Subnet Mask Default Gateway Switch Port R1 FA0/1
Configuring Role-Based Access Control
5 CHAPTER This chapter describes how to configure role-based access control (RBAC) on the Cisco Application Control Engine (ACE) module. This chapter contains the following sections: Information About
Document ID: 45741. Introduction
Products & Services 6bone Connection Using 6to4 Tunnels for IPv6 Document ID: 45741 Contents Introduction Prerequisites Requirements Components Used Conventions How 6to4 Tunnels Work Limitations of 6to4
ICND1 Lab Guide. 100-101 Interconnecting Cisco Networking Devices Part 1 Version 2.0. Labs powered by
ICND1 Lab Guide 100-101 Interconnecting Cisco Networking Devices Part 1 Version 2.0 ii Interconnecting Cisco Networking Devices Part 1 100-101 Lab Guide LM20130929/BV2.01 iii 25 Century Blvd. Ste. 500
Network Security 2. Module 6 Configure Remote Access VPN
1 1 Network Security 2 Module 6 Configure Remote Access VPN 2 Learning Objectives 6.1 Introduction to Cisco Easy VPN 6.2 Configure the Easy VPN Server 6.3 Configure Easy VPN Remote for the Cisco VPN Client
Cisco CCNA Optional Semester 4 Labs Wide Area Networking LAB 1 T1 TSU WAN LINK OVERVIEW - Instructor Guide (Estimated time: 30 minutes)
CNAP @ VCC 1 of 8 LAB 1 T1 TSU WAN LINK OVERVIEW - Instructor Guide (Estimated time: 30 minutes) Objectives: Understand the function of a T1 Service Unit (TSU) in network telecommunications Connect routers
LAN-Cell to Cisco Tunneling
LAN-Cell to Cisco Tunneling Page 1 of 13 LAN-Cell to Cisco Tunneling This Tech Note guides you through setting up a VPN connection between a LAN-Cell and a Cisco router. As the figure below shows, the
Configuring Basic Broadband Internet Access
CHAPTER 4 This chapter describes the parameters of configuring and maintaining basic broadband Internet access. The chapter contains these sections: Overview of Basic Broadband Internet Access section
Supported Platforms. Supported Standards, MIBs, and RFCs. Prerequisites. Related Features and Technologies. Related Documents. Improved Server Access
Configuring Timeout, Retransmission, and Key Values per RADIUS Server The Configuring Timeout, Retransmission, and Key Values per RADIUS Server feature extends the functionality of the existing radius-server
IPSec. User Guide. 2120028 Rev 2.2
IPSec User Guide 2120028 Rev 2.2 Important Notice Safety and Hazards Due to the nature of wireless communications, transmission and reception of data can never be guaranteed. Data may be delayed, corrupted
Quality of Service and Bandwidth Management Configuration
Quality of Service and Bandwidth Management Configuration This topic provides a reference configuration for Quality or Service (QoS) and bandwidth management using RSVP within a Cisco Unified Communications
Cisco IOS Security Command Reference: Commands S to Z, Cisco IOS XE Release 3SE (Catalyst 3850 Switches)
Cisco IOS Security Command Reference: Commands S to Z, Cisco IOS XE Release 3SE (Catalyst 3850 Switches) First Published: January 11, 2013 Last Modified: January 11, 2013 Americas Headquarters Cisco Systems,
Task 20.1: Configure ASBR1 Serial 0/2 to prevent DoS attacks to ASBR1 from SP1.
Task 20.1: Configure ASBR1 Serial 0/2 to prevent DoS attacks to ASBR1 from SP1. Task 20.2: Configure an access-list to block all networks addresses that is commonly used to hack SP networks. Task 20.3:
Firewall Authentication Proxy for FTP and Telnet Sessions
Firewall Authentication Proxy for FTP and Telnet Sessions First Published: May 14, 2003 Last Updated: August 10, 2010 Before the introduction of the Firewall Authentication Proxy for FTP and Telnet Sessions
- The PIX OS Command-Line Interface -
1 PIX OS Versions - The PIX OS Command-Line Interface - The operating system for Cisco PIX/ASA firewalls is known as the PIX OS. Because the PIX product line was acquired and not originally developed by
Virtual Fragmentation Reassembly
Virtual Fragmentation Reassembly Currently, the Cisco IOS Firewall specifically context-based access control (CBAC) and the intrusion detection system (IDS) cannot identify the contents of the IP fragments
Cisco Routers and Switches
Cisco Routers and Switches Phoenix Cisco User Group (PCUG) Tools, tips, and tricks you never knew Hello! Jeremy D. Cioara - CCIE, MCSE, CNE AdTEC Networks - Chief Information Officer Cisco IP Telephony
Table of Contents. Cisco Configuring IPSec Cisco Secure VPN Client to Central Router Controlling Access
Table of Contents Configuring IPSec Cisco Secure VPN Client to Central Router Controlling Access...1 Introduction...1 Prerequisites...1 Requirements...1 Components Used...1 Conventions...1 Configure...2
FWSM introduction Intro 5/1
Intro 5/0 Content: FWSM introduction Requirements for FWSM 3.2 How the Firewall Services Module Works with the Switch Using the MSFC Firewall Mode Overview Stateful Inspection Overview Security Context
Schools Configuration Files Guide
This document, contains the network diagram, and a list of all the platforms and software releases which were validated for the Schools Service Ready Architecture (SRA). The last section includes the configurations
Module 6 Configure Remote Access VPN
Network Security 2 Module 6 Configure Remote Access VPN Learning Objectives 6.1 Introduction to Cisco Easy VPN 6.2 Configure the Easy VPN Server 6.3 Configure Easy VPN Remote for the Cisco VPN Client 4.x
Verizon Wireless Dynamic Mobile Network Routing LTE - Cisco Integrated Services Router (ISR) and Connected Grid Router
Guide Verizon Wireless Dynamic Mobile Network Routing LTE - Cisco Integrated Services Router (ISR) and Connected Grid Router Mobile Router Configuration Guide for Primary Verizon Wireless Access Revision
Provisioning Dial Access to MPLS VPN Integration
CHAPTER 3 Provisioning Dial Access to MPLS VPN Integration This chapter describes how to provision each of the methods of dial access to MPLS (Multiprotocol Label Switching) VPN (virtual private network)
APNIC Members Training Course Security workshop. 2-4 July, 2008. Port Vila Vanuatu. In conjunction with PACNOG 4
APNIC Members Training Course Security workshop 2-4 July, 2008 Port Vila Vanuatu In conjunction with PACNOG 4 Router device security lab 1. APNIC s remote lab In these exercises you will be remotely accessing
Domain Name System Server Round-Robin Functionality for the Cisco AS5800
Domain Name System Server Round-Robin Functionality for the Cisco AS5800 This feature module describes Domain Name System (DNS) server round-robin functionality for the Cisco AS5800 universal access server.
OBJECTIVES This paper examines how NetFlow is implemented on logical interfaces. Logical interfaces can be divided into two groups:
Configuration Guide NetFlow on Logical Interfaces: Frame Relay, Asynchronous Transfer Mode, Inter-Switch Link, 802.1q, Multilink Point to Point Protocol, General Routing Encapsulation, Layer 2 Tunneling
Network Scenarios Pagina 1 di 35
Network Scenarios Pagina 1 di 35 Table of Contents Network Scenarios Cisco 827 s Network Connections Internet Access Scenarios Before You Configure Your Internet Access Network Replacing a Bridge or Modem
Configuring NetFlow Secure Event Logging (NSEL)
73 CHAPTER This chapter describes how to configure NSEL, a security logging mechanism that is built on NetFlow Version 9 technology, and how to handle events and syslog messages through NSEL. The chapter
Using Link Layer Discovery Protocol in Multivendor Networks
Using Link Layer Discovery Protocol in Multivendor Networks Link Layer Discovery Protocol (LLDP), standardized by the IEEE as part of 802.1ab, enables standardized discovery of nodes, which in turn facilitates
Cisco 2621 Gateway-PBX Interoperability: Lucent/Avaya Definity G3si V7 PBX with Cisco CallManager Using T1 PRI NI-2 for an H.
Application Note Cisco 2621 Gateway-PBX Interoperability: Lucent/Avaya Definity G3si V7 PBX with Cisco CallManager Using T1 PRI NI-2 for an H.323 Gateway Introduction This document describes the interoperability
Output Interpreter. SHOW RUNNING-CONFIG SECURITY Analysis SHOW RUNNING-CONFIG - FW Analysis. Back to top
Output Interpreter You have chosen to display errors warnings general information, and helpful references. Headings are displayed for all supported commands that you submitted. SHOW RUNNING-CONFIG SECURITY
http://www.cisco.com/c/en/us/support/docs/cloud-systems-management/configuration-prof...
Page 1 of 16 Configuration Professional: Site-to-Site IPsec VPN Between ASA/PIX and an IOS Router Configuration Example Document ID: 112153 Updated: Sep 22, 2014 Contents Introduction Prerequisites Requirements
Brocade to Cisco Comparisons
1 2 3 Console cables - The console cables are not interchangeable between Brocade and Cisco. Each vendor provides their console cable with each manageable unit it sells. Passwords - Neither Cisco or Brocade
A2.03 AdTran NetVanta 1355/6355 SIP/TDM/IP Appliance
A2.03 AdTran NetVanta 1355/6355 SIP/TDM/IP Appliance 1 Important Notes Check the SIP 3 rd Party Validation Website for current validation status. The SIP 3 rd Part Validation Website can be viewed at:
Configuring Server Load Balancing
CHAPTER 6 This chapter describes how to configure server load balancing (SLB) on the Cisco Application Control Engine (ACE) module. This chapter contains the following sections: Information About Server
Cisco ASA Configuration Guidance
Cisco ASA Configuration Guidance Abstract The modern network perimeter is more complicated than ever. The number of applications, protocols, and attacks that a firewall is expected to support and protect
Configuring NetFlow Secure Event Logging (NSEL)
75 CHAPTER This chapter describes how to configure NSEL, a security logging mechanism that is built on NetFlow Version 9 technology, and how to handle events and syslog messages through NSEL. The chapter
Enabling Management Protocols: NTP, SNMP, and Syslog
SECTION 7 Enabling Management Protocols: NTP, SNMP, and Syslog In this Section This section describes how to enable basic management protocols on a Cisco AS5800 and Cisco AS5300 as part of a dial access
Enabling Remote Access to the ACE
CHAPTER 2 This chapter describes how to configure remote access to the Cisco Application Control Engine (ACE) module by establishing a remote connection by using the Secure Shell (SSH) or Telnet protocols.
Basic Router Configuration
CHAPTER 3 This chapter provides procedures for configuring the basic parameters of your Cisco router, including global parameter settings, routing protocols, interfaces, and command-line access. It also
Configuring Logging. Information About Logging CHAPTER
52 CHAPTER This chapter describes how to configure and manage logs for the ASASM/ASASM and includes the following sections: Information About Logging, page 52-1 Licensing Requirements for Logging, page
Objectives. Background. Required Resources. CCNA Security
Chapter 8 Lab B, Configuring a Remote Access VPN Server and Client Topology IP Addressing Table Device Interface IP Address Subnet Mask Default Gateway Switch Port R1 FA0/1 192.168.1.1 255.255.255.0 N/A
Network Diagram Scalability Testbed and Configuration Files
APPENDIX A Network Diagram Scalability Testbed and Configuration Files This appendix contains configurations that were used during a V 3 PN performance and scalability evaluation based on the network illustrated
NetVanta 7060/7100 Configuration Checklist
NetVanta 7060/7100 Configuration Checklist AOS Versions Supported: AOS A1.01.00 and above. AOS Versions Supporting SIP Trunking and Networking: AOS A2.02.00 and above. This document is designed to provide
Table of Contents. Cisco Configuring a Basic MPLS VPN
Table of Contents Configuring a Basic MPLS VPN...1 Introduction...1 Prerequisites...1 Requirements...1 Components Used...2 Related Products...2 Conventions...2 Configure...3 Network Diagram...3 Configuration
Using a Sierra Wireless AirLink Raven X or Raven-E with a Cisco Router Application Note
Using a Sierra Wireless AirLink Raven X or Raven-E with a Application Note Cisco routers deliver the performance, availability, and reliability required for scaling mission-critical business applications
Center for Internet Security Gold Standard Benchmark for Cisco IOS
Center for Internet Security Gold Standard Benchmark for Cisco IOS Level 1 and 2 Benchmarks Version 2.1 http://www.cisecurity.org [email protected] September 2, 2003 Abstract This document defines
Route-Switch-Controller Handover Redundancy on the Cisco AS5850
Route-Switch-Controller Handover Redundancy on the Cisco AS5850 Feature History Release Modification 122(2)XB1 This feature was introduced on the Cisco AS5850 122(11)T This feature was integrated into