Cisco 2621 Gateway-PBX Interoperability: Lucent/Avaya Definity G3si V7 PBX with Cisco CallManager Using T1 PRI NI-2 for an H.
|
|
- Norah Wiggins
- 7 years ago
- Views:
Transcription
1 Application Note Cisco 2621 Gateway-PBX Interoperability: Lucent/Avaya Definity G3si V7 PBX with Cisco CallManager Using T1 PRI NI-2 for an H.323 Gateway Introduction This document describes the interoperability of a Lucent/Avaya Definity G3si PBX connected via an ISDN T1 PRI link with a Cisco 2621 gateway. The following notes apply: Connectivity is achieved by using the industry standard PRI NI-2 protocol. The Lucent/Avaya Definity G3si can be configured as either network or user side. The Lucent/Avaya Definity G3si PBX configuration screen for the DS1 trunk interface is reached using change ds1 a12 command, setting the T1 physical layer parameters. The Cisco 2621 gateway with ISDN switch type setting of primary-ni supports both protocol sides by using the isdn protocol-emulate command. When the router is set to emulate network side and the Lucent/Avaya is set to emulate user side, the Lucent/Avaya PBX must send at least 10 digits for the gateway to properly route the call; otherwise, the Cisco 2621 gateway sends back a release message containing a release cause of Invalid Number Format. The following key features are supported: Calling/Called Number Calling Name 2003 Cisco Systems, Inc. All right reserved. Page 1 of 20 EDCS#
2 Network Topology As shown in the following diagram, a Lucent/Avaya Definity G3si PBX is connected via an ISDN T1 PRI link to a Cisco 2621 gateway, which in turn, is connected to an Ethernet switch. Limitations The following key features are not supported: Connected Number Connected Name System Components Hardware Requirements Cisco Hardware Cisco 2621 Gateway with 2 MFT T1 Port Lucent/Avaya Definity G3si V7 PBX System: G3siV7 Hardware: TN464F, DS1 INTFC 24/32. Software Requirements Cisco IOS Software Release: c2600-js-mz t PBX Software Release: Version V7 Cisco CallManager Release 3.1 Page 2 of 20
3 Configuration Configuring the Lucent/Avaya Definity G3si PBX Configure the PBX in the following sequence: 1. Add the new circuit pack 2. Add the new signaling group 3. Add the new trunk group 4. Add Uniform Dialing Plan Page 3 of 20
4 DS1 Circuit Pack, Screen1 Page 4 of 20
5 DS1 Circuit Pack, Screen 2 Page 5 of 20
6 Signaling Group Page 6 of 20
7 Trunk Group, Screen 1 Page 7 of 20
8 Trunk Group, Screen 2 Page 8 of 20
9 Trunk Group, Screen 4 Page 9 of 20
10 Trunk Group, Screen 5 Page 10 of 20
11 Uniform Dialing Plan Record Page 11 of 20
12 Uniform Dialing Plan, Screen 1 Page 12 of 20
13 Configuring Cisco CallManager H.323 (Cisco 2621) Gateway Configuration Page 13 of 20
14 H.323 (Cisco 2621) Gateway Configuration Page 14 of 20
15 H.323 (Cisco 2621) Gateway Configuration Page 15 of 20
16 Route Pattern Configuration Page 16 of 20
17 Route Pattern Configuration Configuring the Cisco 2621 Gateway version 12.2 no parser cache service timestamps debug datetime msec localtime show-timezone service timestamps log uptime no service password-encryption hostname 2621_B no logging buffered enable password cisco memory-size iomem 15 voice-card 1 dspfarm ip subnet-zero no ip domain-lookup Page 17 of 20
18 isdn switch-type primary-ni voice class codec 1 codec preference 1 g729r8 codec preference 2 g711ulaw codec preference 3 g711alaw controller T1 1/0 framing esf linecode b8zs pri-group timeslots 1-24 controller T1 1/1 shutdown framing esf linecode b8zs interface FastEthernet0/0 ip address no ip mroute-cache load-interval 30 no keepalive speed auto half-duplex interface FastEthernet0/1 ip address no ip mroute-cache duplex auto speed auto interface Serial1/0:23 no ip address no logging event link-status isdn switch-type primary-ni isdn incoming-voice voice isdn T309-enable isdn T isdn T no cdp enable router rip network network ip classless no ip http server ip pim bidir-enable Page 18 of 20
19 dialer-list 1 protocol ip permit dialer-list 1 protocol ipx permit snmp-server packetsize 4096 snmp-server manager tftp-server nvram call rsvp-sync voice-port 1/0:23 mgcp profile default dial-peer cor custom dial-peer voice 1 pots destination-pattern 2... direct-inward-dial port 1/0:23 prefix 2 dial-peer voice 3 voip destination-pattern 4... progress_ind setup enable 1 voice-class codec 1 session target ipv4: dtmf-relay h245-alphanumeric line con 0 exec-timeout 0 0 line aux 0 exec-timeout 0 0 line vty 0 4 exec-timeout 0 0 password cisco login line vty 5 15 exec-timeout 0 0 login scheduler allocate end Important Information THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS. Page 19 of 20
20 IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING, WITHOUT LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Page 20 of 20
System Components PBX Model. Configuration Tasks
Cisco 3600 Series Gateway-PBX Interoperability: Lucent Definity G3 with T1 PRI Signaling This document describes the interoperability and configuration of a Cisco 3600 series voice gateway with a Lucent
More informationCisco 3640 - PBX Interoperability: Lucent/Avaya Definity G3si V7 PBX with CallManager using Analog FXS and FXO Interfaces as an MGCP Gateway
Application Note Cisco 3640 - PBX Interoperability: Lucent/Avaya Definity G3si V7 PBX with CallManager using Analog FXS and FXO Interfaces as an MGCP Gateway Introduction This application note describes
More informationConfiguring Fax Pass-Through
Configuring Fax Pass-Through This chapter describes the configuration of fax pass-through. With fax pass-through, modulated fax information from the PSTN is passed in-band over a voice speech path in an
More informationConfiguring Modem Transport Support for VoIP
Configuring Modem Transport Support for VoIP This chapter explains how to configure modem transport support for Voice over IP (VoIP) and contains the following sections: Modem Transport Support Overview,
More informationSystem Components PBX Model. Configuration Tasks
Cisco 3600 Series Gateway-PBX Interoperability: Lucent Definity G3 with E1 R2 Signaling This document describes the interoperability and configuration of a Cisco3600 series voice gateway with a Lucent
More informationDial Peer Configuration Examples
Dial Peer Configuration Examples This appendix contains a series of configuration examples featuring the minimum required components and critical Cisco IOS command lines extracted from voice gateway configuration
More informationLab 4.1.4 Creating a Network Map using CDP Instructor Version 2500
Lab 4.1.4 Creating a Network Map using CDP Instructor Version 2500 Objective Use Cisco Discovery Protocol (CDP) commands to get information about neighboring network devices. Background/Preparation CDP
More informationCisco IOS Voice Gateway PBX Interoperability: Avaya 8500 Communications Manager 2.1 to T1 QSIG with H.323
Application Note Cisco IOS Voice Gateway PBX Interoperability: Avaya 8500 Communications Manager 2.1 to T1 QSIG with H.323 Table of Contents Introduction...1 Network Topology...2 Limitations...2 Hardware
More informationNetwork Diagram Scalability Testbed and Configuration Files
APPENDIX A Network Diagram Scalability Testbed and Configuration Files This appendix contains configurations that were used during a V 3 PN performance and scalability evaluation based on the network illustrated
More informationCisco ISDN PRI to SIP Gateway
Cisco ISDN PRI to SIP Gateway Supported features Full ISDN E1 emulation Early media support Inbound calling. Type SIP REGISTERED TRUNK Outbound Calling ISDN PRI equivalent Secure Calling via SIP Encrypt
More informationConfiguring Voice and Data Support on VWIC3s
First Published: July 21, 2010, OL-22847-01 This module describes how to configure voice and data support on the next generation of voice/wan Interface Cards (VWICs) also known as VWIC3s. The following
More informationCase Study 1: Registering IP Phones with a remote Call
Case Study 1: Registering IP Phones with a remote Call Manager Objectives Place calls from IP Phones under R1 to IP Phones under R2 Place calls from any IP Phone (under R1 and under R2) to the regular
More informationBRI to PRI Connection Using Data Over Voice
BRI to PRI Connection Using Data Over Voice Document ID: 14962 Contents Introduction Prerequisites Requirements Conventions Background Information Configure Network Diagram Configurations Verify Troubleshoot
More informationConfiguring Network Side ISDN PRI Signaling, Trunking, and Switching
Configuring Network Side ISDN PRI Signaling, Trunking, and Switching This chapter describes the Network Side ISDN PRI Signaling, Trunking, and Switching feature. The following main sections are provided:
More informationTable of Contents. Cisco Configuring IPSec Cisco Secure VPN Client to Central Router Controlling Access
Table of Contents Configuring IPSec Cisco Secure VPN Client to Central Router Controlling Access...1 Introduction...1 Prerequisites...1 Requirements...1 Components Used...1 Conventions...1 Configure...2
More informationCisco Voice Gateways. PacNOG6 VoIP Workshop Nadi, Fiji. November 2009. Jonny Martin - jonny@jonnynet.net
Cisco Voice Gateways PacNOG6 VoIP Workshop Nadi, Fiji. November 2009 Jonny Martin - jonny@jonnynet.net Voice Gateways Any device with one or more TDM PSTN interfaces on them TDM - Time Division Multiplexing
More informationConfiguring the MNLB Forwarding Agent
CHAPTER 3 Configuring the MNLB Forwarding Agent This chapter describes how to configure a Cisco router as an MNLB Forwarding Agent to operate in conjunction with a Cisco LocalDirector serving as Services
More informationConfiguring a Leased Line
CHAPTER 4 Configuring a Leased Line The configuration in this chapter describes how to configure a Cisco 1700 router for IP and IPX over a synchronous serial line. Before You Begin The configuration in
More informationLAN-Cell to Cisco Tunneling
LAN-Cell to Cisco Tunneling Page 1 of 13 LAN-Cell to Cisco Tunneling This Tech Note guides you through setting up a VPN connection between a LAN-Cell and a Cisco router. As the figure below shows, the
More informationIntegrated Data and Voice Services for ISDN PRI Interfaces on Multiservice Access Routers
Integrated Data and Voice Services for ISDN PRI Interfaces on Multiservice Access Routers This chapter describes how to configure ISDN PRI interfaces to support the integration of data and voice calls
More informationConfiguring ISDN Special Signaling
Configuring ISDN Special Signaling This chapter describes features that either depend on special signaling services offered by an ISDN network service provider or overcome an inability to deliver certain
More informationand 2, implemented With Cisco Unified Border Control Element (CUBE)
www.xo.com XO SIP Service Customer Configuration Guide for Cisco Unified Communications Manager (CUCM) 8.0.3 XO SIP Packages 1 and 2, implemented With Cisco Unified Border Control Element (CUBE) 1 PRODUCT
More informationCisco CCNA Optional Semester 4 Labs Wide Area Networking LAB 1 T1 TSU WAN LINK OVERVIEW - Instructor Guide (Estimated time: 30 minutes)
CNAP @ VCC 1 of 8 LAB 1 T1 TSU WAN LINK OVERVIEW - Instructor Guide (Estimated time: 30 minutes) Objectives: Understand the function of a T1 Service Unit (TSU) in network telecommunications Connect routers
More informationTable of Contents. Cisco Mapping Outbound VoIP Calls to Specific Digital Voice Ports
Table of Contents Mapping Outbound VoIP Calls to Specific Digital Voice Ports...1 Introduction...1 Before You Begin...1 Conventions...1 Prerequisites...1 Components Used...1 Configure...2 Network Diagram...2
More informationUsing a Sierra Wireless AirLink Raven X or Raven-E with a Cisco Router Application Note
Using a Sierra Wireless AirLink Raven X or Raven-E with a Application Note Cisco routers deliver the performance, availability, and reliability required for scaling mission-critical business applications
More informationEnabling Management Protocols: NTP, SNMP, and Syslog
SECTION 7 Enabling Management Protocols: NTP, SNMP, and Syslog In this Section This section describes how to enable basic management protocols on a Cisco AS5800 and Cisco AS5300 as part of a dial access
More informationConfiguring Voice over IP
CHAPTER 4 This chapter explains how to configure voice interfaces and ports, which convert telephone voice signals for transmission over an IP network. This chapter presents the following major topics:
More informationDocument ID: 45741. Introduction
Products & Services 6bone Connection Using 6to4 Tunnels for IPv6 Document ID: 45741 Contents Introduction Prerequisites Requirements Components Used Conventions How 6to4 Tunnels Work Limitations of 6to4
More informationTable of Contents. Cisco Using the Cisco IOS Firewall to Allow Java Applets From Known Sites while Denying Others
Cisco IOS Firewall to Allow Java Applets From Known Sites w Table of Contents Using the Cisco IOS Firewall to Allow Java Applets From Known Sites while Denying Others...1 Introduction...1 To Deny Java
More informationProposal for implementation of VoIP at XYZ hospital.
Proposal for implementation of VoIP at XYZ hospital. Introduction Management committee of XYZ hospital wants to implement an internal voice communication system for their hospital. At present they are
More informationConfiguring a Cisco 2509-RJ Terminal Router
created by: Rainer Bemsel Version 1.0 Dated: Dec/08/2012 For my Cisco LAB, I ve purchased a used Cisco 2509-RJ with RJ45-RJ45 roll-over cables. This TechTip shows my configuration setup, so you can easily
More informationQuality of Service and Bandwidth Management Configuration
Quality of Service and Bandwidth Management Configuration This topic provides a reference configuration for Quality or Service (QoS) and bandwidth management using RSVP within a Cisco Unified Communications
More informationHow To Set Up A Dialogic.Com On A Cell Phone With A Sim Sim Sims On A Sims 2 (For A Simplon) On A Pts 2 ( For A Pty Phone) On An Ipad Or
Dialogic Brooktrout SR140 Fax Software with Cisco Unified Communications Manager 8.0 IMPORTANT NOTE This document is not to be shared with or disseminated to other third parties, in whole or in part, without
More informationLab 7.2.9 Load Balancing Across Multiple Paths Instructor Version 2500
Lab 7.2.9 Load Balancing Across Multiple Paths Instructor Version 2500 Objective onfigure Load balance across multiple paths. Observe the load balancing process. Background/Preparation able a network similar
More informationCisco Catalyst 6000 Series Gateway-PBX Interoperability: Inter-Tel Axxess Key System with T1 PRI NI-2 Signaling
Cisco Catalyst 6000 Series Gateway-PBX Interoperability: Inter-Tel Axxess Key System with T1 PRI NI-2 Signaling This document describes the interoperability and configuration of a Cisco Catalyst 6000 series
More informationNetwork Scenarios Pagina 1 di 35
Network Scenarios Pagina 1 di 35 Table of Contents Network Scenarios Cisco 827 s Network Connections Internet Access Scenarios Before You Configure Your Internet Access Network Replacing a Bridge or Modem
More informationVoIP Configuration Examples
APPENDIX C This section uses four different scenarios to demonstrate how to configure Voice over IP (VoIP). The actual VoIP configuration procedure depends on the topology of your voice network. The following
More informationCisco 2651 - PBX Interoperability: NEC NEAX 2400 ICS PBX with Analog FXS/FXO Interfaces to Cisco Call Manager as an MGCP Gateway
Cisco 2651 - PBX Interoperability: NEC NEAX 2400 ICS PBX with Analog FXS/FXO Interfaces to Cisco Call Manager as an MGCP Gateway Introduction This is an application note for connectivity of the NEC NEAX
More informationVirtual Fragmentation Reassembly
Virtual Fragmentation Reassembly Currently, the Cisco IOS Firewall specifically context-based access control (CBAC) and the intrusion detection system (IDS) cannot identify the contents of the IP fragments
More informationAvaya one-x Quick Edition Interoperability with Cisco Integrated Services Router (ISR) SIP Gateway - Issue 1.0
Avaya Solution & Interoperability Test Lab Avaya one-x Quick Edition Interoperability with Cisco Integrated Services Router (ISR) SIP Gateway - Issue 1.0 Abstract Avaya one-x Quick Edition R3.1 provides
More informationConfiguring Voice over IP
Configuring Voice over IP This chapter provides an overview of Voice over IP (VoIP) technology and gives step-by-step configuration tasks. The chapter contains the following sections: VoIP Benefits, page
More informationConfiguring the Cisco Secure PIX Firewall with a Single Intern
Configuring the Cisco Secure PIX Firewall with a Single Intern Table of Contents Configuring the Cisco Secure PIX Firewall with a Single Internal Network...1 Interactive: This document offers customized
More informationLab Configuring Syslog and NTP (Instructor Version)
(Instructor Version) Instructor Note: Red font color or Gray highlights indicate text that appears in the instructor copy only. Topology Addressing Table Objectives Device Interface IP Address Subnet Mask
More informationADTRAN SBC and Cisco Call Manager Express SIP Trunk Interoperability
6AOSSG0007-42A March 2013 Interoperability Guide ADTRAN SBC and Cisco Call Manager Express SIP Trunk Interoperability This guide describes an example configuration used in testing the interoperability
More informationSimple MPLS network topology for Dynamips/Olive
Simple MPLS network topology for Dynamips/Olive R1 version 12.4 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption hostname R1 boot-start-marker
More informationVoice Dial Plans, Configuring Voice Interfaces and Dial Peers
Voice Dial Plans, Configuring Voice Interfaces and Dial Peers Cisco Networking Academy Program 1 Call Establishment Principles 2 Dial-Peer Call Legs 3 End-to-End Calls 4 Configuring Dial Peers 5 Understanding
More informationLab 1.4.1 Introductory Lab 1 - Getting Started and Building Start.txt
Lab 1.4.1 Introductory Lab 1 - Getting Started and Building Start.txt Objective This lab may introduce new CCNP lab equipment and certain IOS features. This introductory activity also describes how to
More informationHow To Configure A Cisco Router With A Cio Router
CHAPTER 1 This chapter provides procedures for configuring the basic parameters of your Cisco router, including global parameter settings, routing protocols, interfaces, and command-line access. It also
More informationDirect Inward Dial Digit Translation Service
Direct Inward Dial Digit Translation Service In Cisco CME 3.2.3 and later versions, a Tcl script is available to provide digit translation for Direct Inward Dial (DID) calls when the DID digits provided
More informationMotorola TEAM WSM - Cisco Unified Communications Manager Express (CME) Integration
Motorola TEAM WSM - Cisco Unified Communications Manager Express (CME) Integration Summary This setup covers the of the TEAM VoWLAN solution with a Cisco Communications Manager Express 4.1 +. This integration
More informationCVOICE Exam Topics Cisco Voice over IP Exam #642-432 7/14/2005
CVOICE Exam Topics Cisco Voice over IP Exam #642-432 7/14/2005 From the Cisco CVOICE 642-432 Exam Topics Voice over IP Technologies Describe the similarities and differences between PSTN and VoIP including
More informationLab 1.5.1 Introductory Lab 1 Getting Started and Building Start.txt
Lab 1.5.1 Introductory Lab 1 Getting Started and Building Start.txt Objective This lab will introduce to the student the CCNP lab equipment and certain IOS features that might be new. This introductory
More informationLet's take a look at another example, which is based on the following diagram:
Chapter 3 - Voice Dial Peers In order to understand the concept of dial peers, it is important to understand call legs. A voice call over a packet network is segmented into discrete call legs. A call leg
More informationConfiguring Echo Cancellation
Configuring Echo Cancellation Echo cancellation is a key function in packet voice Much of the perceived quality of the connection depends on the performance of the echo canceller The G168 extended echo
More informationRoute-Switch-Controller Handover Redundancy on the Cisco AS5850
Route-Switch-Controller Handover Redundancy on the Cisco AS5850 Feature History Release Modification 122(2)XB1 This feature was introduced on the Cisco AS5850 122(11)T This feature was integrated into
More informationObjectives Understand Cisco IOS system architecture components. Work with the Cisco IOS Command Line Interface (CLI) and common commands.
Objectives Understand Cisco IOS system architecture components. Work with the Cisco IOS Command Line Interface (CLI) and common commands. Learn about Cisco IOS troubleshooting techniques. Understand upgrading
More information- Basic Voice over IP -
1 Voice over IP (VoIP) - Basic Voice over IP - Voice over IP (VoIP) is a digital form of transport for voice transmissions, replacing analog phone systems. The benefits of VoIP are considerable: Better
More informationLab 5.3.9b Managing Router Configuration Files Using TFTP
Lab 5.3.9b Managing Router Configuration Files Using TFTP Device Host Name Interface IP Address Subnet Mask R1 R1 Fast Ethernet 0/0 172.17.0.1 255.255.0.0 Objectives Download and install TFTP server software.
More informationFelix Rohrer. PT Activity 7.5.3: Troubleshooting Wireless WRT300N. Topology Diagram
Felix Rohrer PT Activity 7.5.3: Troubleshooting Wireless WRT300N Topology Diagram All contents are Copyright 1992 2007 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.
More informationCisco CCA Tool SIP Security methods
Cisco CCA Tool SIP Security methods The Cisco CCA tool (Cisco Configuration Assistant) provides a graphical interface for configuring the UC500 series devices. Once settings have been established using
More informationCS3695/M6-109 Lab 8-NPS02 VOIP Sniffing Ver. 8 Rev. 0
Background For this lab, we will be analyzing some Wireshark capture files that were captured using the ARP Poisoning technique on Cisco VIOP (Voice Over IP) phones As this lab took special equipment (i.e.
More informationConfiguring Basic Broadband Internet Access
CHAPTER 4 This chapter describes the parameters of configuring and maintaining basic broadband Internet access. The chapter contains these sections: Overview of Basic Broadband Internet Access section
More informationCCNA Exploration 4.0: ESwitching Basic Switching / Wireless PT Practice SBA. Switch S1 S1#sh ru Building configuration...
CCNA Exploration 4.0: ESwitching Basic Switching / Wireless PT Practice SBA Switch S1 S1#sh ru Building configuration... Current configuration : 1639 bytes version 12.2 no service timestamps log datetime
More informationAbstract. SZ; Reviewed: WCH 6/18/2003. Solution & Interoperability Test Lab Application Notes 2003 Avaya Inc. All Rights Reserved.
A Sample VPN Tunnel Configuration Using Cisco 3640 and 7100 Routers for Avaya Media Servers and Media Gateways running Avaya MultiVantage Software - Issue 1.1 Abstract These Application Notes outline the
More informationSession Title: Exploring Packet Tracer v5.3 IP Telephony & CME. Scenario
Session Title: Exploring Packet Tracer v5.3 IP Telephony & CME Scenario With the scheduled release of Packet Tracer v5.3 in the near future, this case study is designed to provide you with an insight into
More informationCisco IOS SIP Configuration Guide
Cisco IOS SIP Configuration Guide Dialpeer Configuration Session Number 1 Terminology Call - A connection terminating on or passing through a gateway. Call Leg - The segment of a call associated with a
More informationLab 6.1.3 Configure Local AAA on Cisco Router
Lab 6.1.3 Configure Local AAA on Cisco Router Objective Scenario Topology In this lab, the students will complete the following tasks: Securing and testing access to the privileged EXEC, VTY, and console
More informationSample Configuration Using the ip nat outside source static
Sample Configuration Using the ip nat outside source static Table of Contents Sample Configuration Using the ip nat outside source static Command...1 Introduction...1 Before You Begin...1 Conventions...1
More informationSIP Trunking Configuration Guide for Cisco Unified Communications Manager (CUCM) Version 9.0.1.11005-1 with Cisco Unified Border Element (CUBE)
SIP Trunking Configuration Guide for Cisco Unified Communications Manager (CUCM) Version 9.0.1.11005-1 with Cisco Unified Border Element (CUBE) Table of Contents Introduction... 3 Executive Summary..3
More informationDomain Name System Server Round-Robin Functionality for the Cisco AS5800
Domain Name System Server Round-Robin Functionality for the Cisco AS5800 This feature module describes Domain Name System (DNS) server round-robin functionality for the Cisco AS5800 universal access server.
More informationCurso de Telefonía IP para el MTC. Sesión 4-1 Tipos de llamadas. Mg. Antonio Ocampo Zúñiga
Curso de Telefonía IP para el MTC Sesión 4-1 Tipos de llamadas Mg. Antonio Ocampo Zúñiga Call Types Local: Does not traverse the WAN or PSTN. On-net: Occurs between two telephones on the same data network.
More informationConfiguring Settlement Applications
Configuring Settlement Applications The Cisco Settlement for Packet Telephony feature equips Cisco conferencing infrastructure products to use third-party settlement systems on multiple protocols. The
More informationObjectives. Router as a Computer. Router components and their functions. Router components and their functions
2007 Cisco Systems, Inc. All rights reserved. Cisco Public Objectives Introduction to Routing and Packet Forwarding Routing Protocols and Concepts Chapter 1 Identify a router as a computer with an OS and
More informationConfiguring Dial Backup and Remote Management
13 CHAPTER Configuring Dial Backup and Remote Management The Cisco 800 series access routers support dial-in (for remote management) and dial-out (for dial backup) capabilities. By allowing you to configure
More informationEIGRP Routing Protocol & Configuration
EIGRP Routing Protocol & Configuration ~ GNU Public License ~ ma2d http: // www.oscentre.co.nr A) EIGRP Definition There is several terms on routing protocol, as we know RIP, IGRP/EIGRP, OSPF, BGP is major
More informationLab 7.2.9 Load Balancing Across Multiple Paths
Lab 7.2.9 Load Balancing Across Multiple Paths Objective Configure Load balance across multiple paths. Observe the load balancing process. Background/Preparation Cable a network similar to the one in the
More information642-436 - Cisco Voice over IP
642-436 - Cisco Voice over IP Number: 642-436 Passing Score: 825 Time Limit: 120 min File Version: 2.0 http://www.gratisexam.com/ This material is copy from pass4sure 642-436. All answers was collected
More informationRemote Access VPN Business Scenarios
CHAPTER 4 This chapter explains the basic tasks for configuring an IP-based, remote access Virtual Private Network (VPN) on a Cisco 7200 series router. In the remote access VPN business scenario, a remote
More informationReverse Proxy Caching
CHAPTER 7 This chapter explains reverse proxy caching and shows configuration examples relevant to the Content Engine. This chapter contains the following sections: Overview, page 7-1 Configuring Reverse
More informationTotalCloud Phone System
TotalCloud Phone System Cisco SF 302-08P PoE VLAN Configuration Guide Note: The below information and configuration is for deployment of the Cbeyond managed switch solution using the Cisco 302 8 port Power
More information642-436 Q&A. DEMO Version
Cisco Voice over IP (CVOICE) Q&A DEMO Version Copyright (c) 2010 Chinatag LLC. All rights reserved. Important Note Please Read Carefully For demonstration purpose only, this free version Chinatag study
More informationNote: This case study utilizes Packet Tracer. Please see the Chapter 5 Packet Tracer file located in Supplemental Materials.
Note: This case study utilizes Packet Tracer. Please see the Chapter 5 Packet Tracer file located in Supplemental Materials. CHAPTER 5 OBJECTIVES Configure a router with an initial configuration. Use the
More informationOBJECTIVES This paper examines how NetFlow is implemented on logical interfaces. Logical interfaces can be divided into two groups:
Configuration Guide NetFlow on Logical Interfaces: Frame Relay, Asynchronous Transfer Mode, Inter-Switch Link, 802.1q, Multilink Point to Point Protocol, General Routing Encapsulation, Layer 2 Tunneling
More informationIP Telephony v1.0 Scope and Sequence. Cisco Networking Academy Program
IP Telephony v1.0 Scope and Sequence Cisco Networking Academy Program Table of Content COURSE OVERVIEW...4 Course Description...4 Course Objectives...4 Target Audience...5 Prerequisites...5 Lab Requirements...5
More informationFirst, we must set the Local Dialing Type to 7 or 10 digits. To do this, begin by clicking on Dial Plan under Voice.
Quick Configuration Guide (QCG) TA 900/900e PRI Trunk Quick Start Guide Overview This Configuration Guide explains how to configure a T1 port on the Total Access 900/900e for a PRI to be connected to a
More informationOverview of Dial Interfaces, Controllers, and Lines
Overview of Dial Interfaces, Controllers, and Lines This chapter describes the different types of software constructs, interfaces, controllers, channels, and lines that are used for dial-up remote access.
More informationOverview of Access VPNs and Tunneling Technologies
Overview of Access VPNs and Tunneling Technologies Introduction A virtual private network (VPN) is a network that extends remote access to users over a shared infrastructure. VPNs maintain the same security
More informationConfiguring Static and Dynamic NAT Simultaneously
Configuring Static and Dynamic NAT Simultaneously Document ID: 13778 Contents Introduction Prerequisites Requirements Components Used Conventions Configuring NAT Related Information Introduction In some
More informationConnecting to IP Gateways/PBXs example of a CISCO Gateway
Connecting to IP Gateways/PBXs example of a CISCO Gateway This White Paper is based on Brooktrout/customer experience in setting up a Cisco router and connecting it to the Brooktrout TR1034 IP (-1N) board.
More informationProvisioning Dial Access to MPLS VPN Integration
CHAPTER 3 Provisioning Dial Access to MPLS VPN Integration This chapter describes how to provision each of the methods of dial access to MPLS (Multiprotocol Label Switching) VPN (virtual private network)
More informationConfigurazione Rete VoIP
Configurazione Rete VoIP 1x CISCO 7940G 1x CISCO 3725 with cme-full-7.0.0.1.tar 1x CISCO IP Communicator Startup Config router CISCO 3725 Procedura Operativa: Topologia di rete Operazioni preliminary sul
More informationICND1 Lab Guide. 100-101 Interconnecting Cisco Networking Devices Part 1 Version 2.0. Labs powered by
ICND1 Lab Guide 100-101 Interconnecting Cisco Networking Devices Part 1 Version 2.0 ii Interconnecting Cisco Networking Devices Part 1 100-101 Lab Guide LM20130929/BV2.01 iii 25 Century Blvd. Ste. 500
More informationImplementing Cisco Voice Communications and QoS
Implementing Cisco Voice Communications and QoS Course CVOICE v8.0; 5 Days, Instructor-led Course Description Implementing Cisco Voice Communications and QoS (CVOICE) v8.0 teaches learners about voice
More informationBrest. Backup : copy flash:ppe_brest1 running-config
Brest Backup : copy flash:ppe_brest1 running-config Cisco SF300-08 Mise en place des services : - Serveurs : 10.3.50.0/24 VLAN 2 (port 1) - DSI : 10.3.51.0/24 VLAN 3 (port 2) - Direction : 10.3.52.0/24
More informationSkills Assessment Student Training Exam
Skills Assessment Student Training Exam Topology Assessment Objectives Part 1: Initialize Devices (8 points, 5 minutes) Part 2: Configure Device Basic Settings (28 points, 30 minutes) Part 3: Configure
More informationConfigurazione Rete VoIP
Configurazione Rete VoIP 1x CISCO 7940G 1x CISCO 3725 with cme-full-7.0.0.1.tar 1x CISCO IP Communicator Startup Config router CISCO 3725 Procedura Operativa: Topologia di rete Operazioni preliminary sul
More informationLab 4.2.4 Advanced Telnet Operations
Lab 4.2.4 Advanced Telnet Operations Objective Use the telnet command to remotely access other routers. Verify that the application layer between the source and the destination is working properly. Suspend
More informationSample Configuration Using the ip nat outside source list C
Sample Configuration Using the ip nat outside source list C Table of Contents Sample Configuration Using the ip nat outside source list Command...1 Introduction...1 Before You Begin...1 Conventions...1
More informationEarthLink Business SIP Trunking. Cisco Call Manager and Cisco CUBE Customer Configuration Guide
EarthLink Business SIP Trunking Cisco Call Manager and Cisco CUBE Customer Configuration Guide Publication History First Release: Version 2.0 April 20, 2012 CHANGE HISTORY Version Date Change Details Changed
More informationOptimizing Converged Cisco Networks (ONT)
Optimizing Converged Cisco Networks (ONT) Module 2: Cisco VoIP Implementations (Deploy) Calculating Bandwidth Requirements for VoIP Objectives Describe factors influencing encapsulation overhead and bandwidth
More information