JUBILEE TECHNICAL TRAINING CENTRE TAKORADI POLYTECHNIC 2015 TRAINING PROGRAMMES
Main Courses Duration: 26 weeks 1. NVQ Level 2 Performing Process Operation in Replicating Environment 2. NVQ Level 2 Performing Engineering Operation in Mechanical 3. NVQ Level 2 Performing Engineering Operation in Electrical 4. NVQ Level 2 Performing Engineering Operation in Instrumentation JTTC Short appreciation courses in the following disciplines Process 1. Process Appreciation (2 weeks) 2. P&ID Drawings ( 2 days) 3. Permit To Work System () 4. Level Control (1 Day) 5. Pressure Control (1 Day) 6. Plant Safety () Mechanical 1. Mechanical Safety (7days) 2. Risk Assessment (2 days) 3. Gears (5 days) 4. Valves (2 days) 5. Bearings (5 days) 6. Pumps (5 days) 7. Thread Cutting (3 days) 8. Drilling (7 days) 9. Locking Devices (2 days) 10. Measurement (2 days) 11. Seals And Lubrications (2 days) 12. Hand Tools (7 days) 13. Marking Out (5 days) 14. Compressor (5 days)
15. Pipe Fitting (7 days) 16. Hydraulic Systems (5 days) 17. Mechanical Engineering For Non-Mechanical Engineers (5 days) Electrical 1. Domestic lighting and power installation (1 week) 2. Inspection and testing (1 week) 3. BS7671 IEE Wiring Regulations (3 days) 4. Installation techniques using tray plate, trunking, metallic and non metallic conduits (2 weeks) 5. Electrical health and safety (1 week) 6. Fault diagnosis (3 days) 7. Panel building (1 week) 8. Earthing (3 days) 9. Sizing: cables, conduit and trunking (3 days) 10. Electrical working practices (3 days) 11. Motor maintenance (3 days) 12. Circuit protective devices (3 days) Instrumentation COURSES - DURATION: 2 WEEKS 1. Instrument Introduction 2. Pressure Measurement 3. Level Measurement 4. Temperature Measurement 5. Flow Measurement 6. Instrument Fitting 7. Hazardous Areas 8. Cause and Effect Diagrams 9. Loop Diagrams 10. Control Valves
JTTC Health & Safety Short Courses NO COURSES DURATION Working at Height Lifting Operations Evacuation Work Confined Space Control of substances hazardous to health (Risk assessment) Contractor Management (on site) Environmental Management Fire hazard, control and emergency response First Aid Risk Assessment Permit to Work Energy Isolation Process Safety Management of Change Driving Safety Electrical Safety Job Safety Analysis Organizing for health and safety Behavioral safety Promoting a positive health and safety culture Principles of control Movement of people and vehicles-hazards and control Manual and mechanical handling hazards and control Work equipment and hazard controls Ergonomics Chemical and biological health hazards and control 1 Day 1 Day 1 Day 1 Day 3Days
Construction activities-hazards and control Incident investigation, recording and reporting Monitoring, review and audit Health and safety legal frame work Certification Course in Occupational Health & Safety Management (5 Days) Certification Course in Occupational Health, Safety & Environmental Management (7 Days) Nebosh Health $ Safety International General Certificate (IGC) Level 3 (10 Days) Other Refresher Courses Risk Management Overview of Oil & Gas Industry Fundamentals of Compressor Systems Instrumentation & Control Fundamentals Gas Conditioning & Processing Operator Training for Oil & Gas Processing Facilities Piping Systems- Mechanical Design & Specification Mathematics for Instrumentation Technicians Fundamentals of Industrial Process, Measurement & Control Introduction to industrial Automation Technology & Innovation Engineering Applied maintenance Management Optimizing Preventive & Predictive Maintenance Effective Maintenance Shutdowns Project Estimation Pipeline Engineering Design, Construction & Operation Gas Plant Process Engineering Gas Plant & Pipeline Management Pipeline Control Systems
Pipeline Costing Potable Water Treatment Heat Medium, Cooling Systems Utilities Management Gas Commercialization & Sales Agreements Onshore/ Offshore Pipeline Activities Fundamentals of Flow Assurance for Pipeline & Piping Systems Maintenance Management on Gas Processing Plant Heat Exchanger/ Transfer Equipment Turbo Machinery Pump & Compressor & Associated Piping Systems Welding Engineering Troubleshooting of Equipment Introduction to High Voltage Electrical Systems Safe use of Equipment Hazardous Areas Process Control Systems Facilities Management Programming Basic Geophysics Soil & Rock Mechanics Basic Geotechnical Engineering AutoCAD, CivilCAD Corrosion Management Effective Materials Management QA/QC Procedures & Activities
EXPERTISE The Centre has TTE Consultants and can boost of 12 local partially trained workforces who are competent to instruct and train. EQUIPMENT Process 3-Phase Separation Plant Water Treatment Plant Control Room to control the plant DCS Mechanical Hydraulic press Pedestal drills Band saw Bench drill Milling and drilling machine Pedestal grinding machine Compressors Bench vices Pumps Centrifugal Diaphragm Gear Valves Gate Check Globe Ball Butterfly Induction heater Optalign alignment kit
Shafts Mechanical seals Hydraulic hoist Electrical Workshop base Instrumentation Automatic input devices Industrial electronics AC/DC Electrical systems PLC control systems Instrument test/calibration bench Dead weight tester system Process control system Basic timer control on delay and off-delay Control ladder logic Control relays and motor starters Systems troubleshooting Reversing motor control Manual motor control and overload protection Introduction to troubleshooting Introduction to electric motor control Control transformers QUALIFICATION AWARDING BODY PAAVQSET (Process Award Authority Vocational Qualification Science Engineering Technology), UK for the 26 Week courses. Certificate of Attendance from JTTC PARTIALLY TRAINED WORKFORCE UP TO STANDARD LOCAL INDUSTRIES TO BUY-IN