Danfoss Link CC Mk II (with minisd card) software..35.3.7.4.5 0--00 The initial Danfoss Link CC software: Supports all features from the original Devilink software. New functionality providing control of radiator thermostats, Danfoss Link HC (Hydronic Controller) and Danfoss Repeater Unit (CF-RU). Includes a Danfoss Design Line background as default skin setting. 04-0-0 Austria, Belgium and Switzerland added in the Country List. Flush functionality to force and TWA actuators fully open in order to flush and remove air in the system. Control of Thermia and Danfoss Heat Pumps with DCM0 (code no. 086L0474). Support of Danfoss Link BR (Boiler Relay) - only Automatic On/Off control is supported. Any number of rooms can be selected as reference, i.e. the boiler will be turned ON if any of the selected rooms call for heat. Note: It is recommended to use software version.4.5 or later for boiler control. 0-03-0 Support of Danfoss Link BR with TPI (Time Proportional Interval) control. A duty cycle is calculated by the Danfoss Link CC and is used to control the boiler: TPI3 splits the hour into intervals of 0 minutes. Example: depending on the calculated heat demand each 0 minutes could be split into 8 minutes ON and minutes OFF. TPI3 is recommended for condensing non-modulating oil boilers. TPI6 splits the hour into intervals of 0 minutes. Example: depending on the calculated heat demand each 0 minutes could be split into 3 minutes ON and 7 minutes OFF. TPI6 is recommended for condensing non-modulating gas boilers. Other Danfoss Link BR features: The Danfoss Link BR is motioned every 7 hours if no other activity. The motion lasts for minute and happens at 5.00 hrs. Example: If the Danfoss Link CC has received no heat demand for 7 hours and the time is 3.00, then the BR will be turned on for minute at 5.00 (7+ hours). If the set point temperature is changed manually (on, Danfoss Link TM RS or Danfoss Link TM CC) to be lower than the measured temperature in a room, the Danfoss Link BR will turn off immediately. This requires that no other reference room is calling for heat. Improved network test to make sure that there is sufficient signal strength between to/from the devices communicating with the Danfoss Link CC. The requirements for getting a valid and positive network test is higher than in the previous software versions: Detailed status of network test with indication of signal strength. A popup dialog will warn the installer if he leaves the Service Area without having made a valid network test. Built-in logging features: It is possible to start a data log of the Danfoss Link system without entering a 3 digit developer license code. A red dot in the upper right corner will indicate if logging is on-going. Disable rooms for cooling (via a Danfoss Link HC). If the consumer uses his hydronic floor heating to cool down the house during warm days the disabling function makes it possible to deselect single rooms and keep a higher temperature in some rooms. Rooms not selected for cooling are not heated. The Danfoss Link TM HC can only be in heating mode or cooling mode, but it is possible to enable different modes for the different Danfoss Link TM HCs in the same Danfoss Link system. User selectable load management on a Danfoss Link HC where it is possible for the user to select between Spreading and Stacking for Danfoss Link TM HC load management. When spreading is enabled the Danfoss Link TM HC will spread the load of hot water between the TWA. A feature also known from CF+. Turkey added in the Country List. Improved and more robust memory management in the Danfoss Link CC. Bug fixes: The list with selected reference rooms for boiler control is now remembered after a reboot of the Danfoss Link TM CC. Missing forecast in the end of an Away mode meaning that the user will come home to a cold house. The Danfoss Link system doesn t start heating until the Away mode is over. This missing forecast in Away mode happens only in rare situations, when ) Away mode is scheduled to start, and ) Just before the Away mode is about to start the user decreases the temperature when being in a set back period. In a room with or Danfoss Link HC Turn Heating On/Off is no longer valid, only Tamper Proof and Frost Protection are valid. Minor bugs not visible to the user or the installer are fixed. VFIDB50 Danfoss /03
.5.57-06-0 Remote sensor support, so temperature control using and Danfoss Link RS can be configured for special heating needs. The extended temperature control makes it possible to configure for special heating applications, where the radiator is hidden behind bars, a furniture or similar. A new menu in the service mode provides the possibility to configure how the radiator is placed: Visible, Covered or in a Trench. Important Note: The new menu will only appear with use of sw 3.0 and when a Danfoss Link RS is installed in the room. External Away functionality: Support of Danfoss Link SCM (Simple Communication Module). The Danfoss Link SCM can wirelessly enable and disable Away mode (Holiday mode) on the Danfoss Link CC. Danfoss Link SCM will be introduced in September/ October 0. The Away icon (suitcase) is only displayed for 0 minutes to avoid showing that nobody is at home. After 0 minutes the normal standby screen with the clock is shown. Built-in data logging is encrypted, so that the data log saved on the memory card can only be read by a Danfoss decryption tool. Danfoss Link CC Mk III (with USB) software 3.0. 09-09-03 New faster hardware with USB-port for software upgrades. Added Setpoint Memory functionality, so the user can select whether or not a change to a setpoint in economy and/or comfort modes should be saved for next economy/comfort period in the room. Support for Danfoss Air units. VFIDB50 Danfoss /03
Danfoss Link Heat Pump kits Product Code 086L38 086L383 Name Danfoss Link. HP kit Danfoss Link. kit AQ Description Heat pump integration kit, for integration with Danfoss Link TM CC. Supports Danfoss DHP OPTI-range produced from year 009, from software version.34. Heat pump integration kit, for integration with Danfoss Link TM CC. Supports Danfoss DHP AQ-range from software version.. Danfoss Link Air Unit Integration Description CCM.07 09-03 CCM unit, for integration with Danfoss Link TM CC. Supports Danfoss Air Units A, A3, W, W. Danfoss Link Compatibility Overview Danfoss Air Unit older than Sept. 03 Danfoss Air Unit newer than Sept. 03 Danfoss Heat Pump older than 009 Danfoss Heat Pump DHP OPTI range after 009 SW v.34-> Danfoss Heat Pump DHP-AQ SW v.->** living eco Danfoss Link HC Danfoss Link RS Danfoss Link FT(S) Danfoss Link HR Danfoss Link PR Danfoss Link BR CF-RU Danfoss Link MPB (incl. Danfoss Link SCM) Danfoss Link SCM Danfoss Link CC SW v..35 Danfoss Link CC SW v.3.7 3 Danfoss Link CC SW v.4.5 Danfoss Link CC SW v.5.57 Danfoss Link CC SW v.7.x* Danfoss Link CC SW v3.0. Danfoss Link CC SW v3..x* Notes:. Requires that CCM is version.07 or newer.. Seperate heat pump kit required (see section: "Danfoss Link Heat Pump kits" for product code). 3. Update to software version.4.5 or later for optimized boiler control (see section: ".3.7"). * Not released yet ** If your DHP-AQ software is older than., please contact your installer in order to change the display card. VFIDB50 Danfoss /03 3
software.06.06 3.0 3.04-07-00 The first batches of are marked with SW.06, but the software version is actually version.06. -03-0 The initial software for - can be controlled by Danfoss Link CC or by a 3rd party Z-wave controller. 5-05-0 Standard Z-wave functionality removed, meaning that no longer can be controlled by a 3rd party controller. Improved (quicker) temperature control. Works also in covered or trench radiator applications (this requires use of Danfoss Link CC with software version.5.57 or later - temperature control in Installation Mode must be set accordingly). 04--0 Valve exercise function changed to minimize the risk of motor stalling. Z software.50.5 Includes standard Z-wave functionality, but can not communicate with Danfoss Link CC. Improved (quicker) temperature control. Valve exercise function changed to minimize the risk of motor stalling. Overview of differences between and Z Feature old 04G000 new 04G000 Z 04G00 SW version.06 3.0 / 3.04.50 /.5 Z-wave protocol Yes No Yes To be controlled by Danfoss Link CC Yes Yes No To be controlled by 3rd party Yes No Yes Hidden radiator application No Yes No Temperature control algorithm Good Better Better 4 VFIDB50 Danfoss /03
living eco software..3.4.5.9.0-07-00 Initial software version for living eco. 9-09-0 Fixing following leap year problems: If user enters the time setup menu on February 9th 0, the display will read 5..03. If an Away period is set with start or end date on February 9th, the display will read 5.. The Forecast feature is not active on February 9th, meaning that the heat is regulated with some delay. 07--0 Display improvements: Extra clock numbers and dots in display. Saving period is no longer highlighted as an empty box in the wheel. When turning the thermostat to MAX or MIN the according icon is displayed. 4-07-0 Child lock preserved during battery change. Optimized constants for PID control. PID control is delayed by 5 minutes after window is closed allowing temperatures to settle before Adaptive learning (forecast) algorithm updated to latest version. Orientation menu is removed since it was not in use. Missing forecast in the end of an Away mode meaning that the user will come home to a cold house. living eco does not start heating until the Away mode is over. However, the missing forecast in Away mode happens only in rare situations, when ) Away mode is scheduled to start, and ) just before the Away mode is about to start the user decreases the temperature when being in a set back period. 9--0 Valve exercise function changed to minimize the risk of motor stalling. Optimized constants for PID control. Adaptive learning (forecast) algorithm updated. Orientation menu removed (was not used). Missing forecast at the end of an Away mode, living eco does not start heating until Away mode is over. 0-06-03 No functional changes, from customer point of view. Orientation functionality is changed, ensuring that living eco cannot accidentally be programmed to vertical.. Not produced Special version with the Intelligent Control (Forecast) deactivated as default. Can be enabled by using the menu. VFIDB50 Danfoss /03 5