CYAN SECURE WEB APPLIANCE User interface manual Jun. 13, 2008 Applies to: CYAN Secure Web 1.4 and above
Contents 1 Log in...3 2 Status...3 2.1 Status / System...3 2.2 Status / Network...4 Status / Network / Secure Web...4 Status / Network / Interface Configuration...4 Interface assignment...5 2.3 Services...6 Status / Services / Secure Web...6 Status / Services / NTP...6 Status / Services / Postfix...6 Status / Services / PostgreSQL...7 Status / Services / OpenSSH...7 3 System...8 3.1 System / Time & Date...8 3.2 System / Logrotate...8 3.3 System / Kaspersky Anti Virus...8 3.4 System / E Mail...8 4 Network...9 4.1 Network / Bridge...9 4.2 Network / Management...9 4.3 Network / DNS...9 4.4 Network / Firewall...10 Network / Firewall / Transparent Proxy...10 Network / Firewall / Access Control...10 5 Maintenance...11 5.1 Maintenance / Disk...11 5.2 Maintenance / Firmware...11 5.3 Maintenance / Power...12 5.4 Maintenance / Appliance Accounts...12 5.5 Maintenance / Factory...12 2008 CYAN Networks Software GmbH - 2 -
1 Log in To log into the CYAN Secure Web Appliance, open a web browser and type in the address: https://<youripaddress>:9999/ Where <youripaddress> is one of the appliance's IP addresses. You can see them on the front display. The default user name and password are both 'admin'. 2 Status The status tab shows information about the hardware and the configuration of your appliance. 2.1 Status / System On the System tab you can see basic information about the hardware of your appliance: Current load: The load is a value calculated from the current memory and cpu usage, as well as some other operating system values. It shows an overview of how busy your machine is. Uptime: Shows, how long your machine is running since the last reboot. Current disk status: Information about the harddisk usage. 2008 CYAN Networks Software GmbH - 3 -
2.2 Status / Network The Network tab shows information about the usage and the configuration of the network interfaces. Status / Network / Secure Web Here you can see how many requests are served by CYAN Secure Web. Active threads: Amount of concurrend threads by Secure Web. Connections: All open network connections are shown here. Status / Network / Interface Configuration This list shows all the appliance's network interfaces and their configuration. 2008 CYAN Networks Software GmbH - 4 -
Interface assignment There are two different CYAN Secure Web Appliance models: Rear view of DS models 0 --> eth3 1 --> eth0 2 --> eth1 3 --> eth2 The first (1) and the second (2) interface are configured in bridged mode for analyzing the passing data traffic. The third one (3) is used for management access to the user interface. The last interface is not in use. Rear view of RS models 0 --> eth0 1 --> eth1 2 --> eth2 3 --> eth3 CYAN Secure Web Appliance has four network interfaces. The first (0) and the second (1) interface are configured in bridged mode for analyzing the passing data traffic. The third one (2) is used for management access to the user interface. The last interface is not in use. If you want to access the appliance directly, you can connect keyboard and monitor here. 2008 CYAN Networks Software GmbH - 5 -
2.3 Services You are able to control the different types of services running on your appliance here. Status / Services / Secure Web This tab show the status of all CYAN Secure Web services. You can start and stop the services here. Status / Services / NTP NTP (Network Time Protocol) is used to synchronize the time on your appliance with time servers in the internet. Status / Services / Postfix Postfix is a open source mail server. Under this tab you can start or stop this service as you like. 2008 CYAN Networks Software GmbH - 6 -
Status / Services / PostgreSQL PostgreSQL is the database used for the CYAN Reporting System. Under this tab you can start or stop the database service. Status / Services / OpenSSH OpenSSH is used to access the appliance from a command line. This is needed mostly only for support issues. If you CYAN Networks support needs to access the machine, you need to make sure that this service is running. 2008 CYAN Networks Software GmbH - 7 -
3 System System specifc parameters can be configured here. 3.1 System / Time & Date Set the time and the date of your appliance Date/Time: System date and time of the appliance. Use client's date/time: Update the appliance settings with your machine's date or time. 3.2 System / Logrotate If log rotation is enabled, all Secure Web log files will be kept for 4 weeks and then deleted. 3.3 System / Kaspersky Anti-Virus You can enable or disable the automatic Kaspersky virus pattern file update here. 3.4 System / E-Mail The mail daemon can be configured to deliver mails in two ways: - Relay all mails to another mail server. Enter the mail server which processed all mails. - Direct delivery. Leave the relay server blank. 2008 CYAN Networks Software GmbH - 8 -
4 Network You can configure the network configuration of your CYAN Secure Web Appliance here. Note: If you change the IP address of the interface you used to connected to the appliance, you need to re-enter the new IP address in the web browser to access the appliance UI again. 4.1 Network / Bridge You can either assign a static IP address to the bridged interfaces (eth0 and eth1), or user DHCP (Dynamic Host Configuration Protocol) to assign one automatically. If you don't use DHCP, you need to specify the IP address, network mask and the gateway for the interface. 4.2 Network / Management Here you can configure the IP address of your management interface. (eth2) The management interface should be used to access the appliance's web interface. Caution: If you assign an IP address to the management interface, which is in the same subnet as the bridged interface, make sure that the routing is correct. 4.3 Network / DNS Under DNS (Domain Name Service) you can configure the IP address and the domain which the appliance should use. Note: If DHCP is enabled, settings may be overwritten from the DHCP daemon when the DHCP lease if refreshed. 2008 CYAN Networks Software GmbH - 9 -
4.4 Network / Firewall This menu is used to configure the appliance's firewall and port mapping. Network / Firewall / Transparent Proxy Transparent mode means, that all reques to a web service passing through the bridged interface will be redirected to CYAN Secure Web. The Proxy port can be changed in CYAN Secure Web. You need to specify the same setting here. The default value is 8080. Network / Firewall / Access Control The firewall can limit the IP addresses and networks which are allowed to access the proxy. Allow management over bridge:br If you disable this setting, you only can access the appliance via the management interface (eth2). Restrict proxy usage: If this is not enabled, all clients can access CYAN Secure Web. You can still limit web access there. Allowed IP networks: If restricted access is enabled, enter a list of allowed IP addresses and subnets seperated by blanks here. (e.g. 192.168.0.0/16 10.1.2.3/32 ) 2008 CYAN Networks Software GmbH - 10 -
5 Maintenance All maintenance tasks can be performed or configured here. 5.1 Maintenance / Disk Here you can delete the content of the log and virus scanning folders of you appliance. Select the options you want and click on Execute. Cyan Secure Web Logfiles: Delete the CYAN Secure Web log files (Path: /opt/cyan/sweb/logs/) Cyan Secure Web HTTP Cache: Delete the cache memory of the proxy server. Cyan Secure Web Vscan Quarantine: Delete the virus scan quarantine folder. Temporary directorys/files: Delete all temporary files. 5.2 Maintenance / Firmware This menu is used to update your appliance software to the latest version. Update: only applies fixes to installed packages and will never remove or install any new packages. Upgrade: applies fixes and upgrades to installed packages and will also remove, replace or install new packages, if needed. If you select to simulate the actions, you will only see an output of what would be done, instead of applying the updates immediately. 2008 CYAN Networks Software GmbH - 11 -
5.3 Maintenance / Power Use this dialog to restart or shut down the appliance. Caution: Once you executed a command here, there is no turning back. 5.4 Maintenance / Appliance Accounts In this menu tab you can enable or disable the support user and set a new password for the administrative user. Appliance user: Set a new password for your admin user to access the appliance. Support user: Enable or disable the support user for the appliance. Set a password for the support user. Caution: The support user is needed to access the appliance via secure shell. No other user (not even root) is configured on the machine. If you disable the support user, there is no way to access the machine besides the web interface. 5.5 Maintenance / Factory This tab will reset all settings to the factory default. Note: Once you executed the command, there is be no turning back. After you push the execute button your appliance will be shut down. 2008 CYAN Networks Software GmbH - 12 -