Swimming pool construction

Swimming pool construction

Swimming pool construction Rehazenter, Luxembourg Architects: m architectes s.a. - Dell, Linster, Lucas, Luxembourg Photo: Weber, Luxembourg Tile range: PRO ARCHITECTURA 2

Impressive technology and versatile design: with the new modular range, we are offering you all the elements and trims you need for both building new and renovating existing swimming pools and wellness facilities. As your contact for ambitious planning requirements, we accompany you from the initial idea through to implementation. Improvements to key components in our range include, for example: Expansion of the trim system for the Finnish and Wiesbaden overflow channel and inclusion of trims for the Berlin overflow channel New overflow channels for all systems with a variable channel size New trims for shallow drainage channels in the pool rim Additions to the curved and cove base ceramic beading system Enlargement of the overflow channel volume and of the outlet openings to increase the outlet quantity Black as new colour alongside white, aquamarine and dark blue New format 10 x 20 cm for PRO ARCHITECTURA with barefoot B and C slip resistance Villeroy & Boch tiles also offers you the following service: Individual technical advice for swimming pool projects (new construction and renovation) Design planning CAD-supported, structural design of swimming pools In combination with modular concepts, such as PRO ARCHITECTURA and various vilbostone porcelain stoneware ranges, you have great freedom when designing a wide variety of different swimming pools.

Swimming pool construction Olympic training center, Saarbrücken Photo: Johannes-Maria Schlorke Tile range: PRO ARCHITECTURA 4

5

Swimming pool construction Aquapark Bruntál, Czech Republic Schwimmoper indoor swimming pool in Wuppertal, pbr Planungsbüro Rohling AG 6

LANDIDYLL Hotel Michels, Schalkenmehren Fron Badeland, Norway Photo: www.imagephoto.no 7

Fundamentals of swimming pool construction Defining the modular dimensions das blau, St. Ingbert Planner: Berwanger architects, St. Wendel The line of swimming pool ceramics consists of modular trims in a nominal length of 200 mm (1 mm + mm joint) and modular tiles from the PRO ARCHITECTURA range. Modular tiles are based on the basic module M (100 mm) and multiples thereof, plus smaller supplementary dimensions, e.g. 50 mm. The modular dimensions of our tiles and functional trims are derived from the factory dimensions plus the joint width. The smaller the tile/functional trim, the smaller the joint can be. The resulting modular dimension will not change. The small format tiles (10 x 10 cm, 5 x 5 cm and 2.5 x 2.5 cm) are supplied on ready-to-set sheets. The sheets are available with the lattice paper attached on the front or back. For wet areas is required using tiles with lattice paper on the front only or with glass fibre lattice backing only. Lattice paper on front and glass fibre lattice backing must be specified when placing orders. Formats larger than 10 x 10 cm are supplied loose in the box. All pool dimensions (rough shell and finished), fixtures, recesses for inlets and drains must be coordinated. The rough shell planning is made on the basis of the tile planning. The V&B Fliesen GmbH tile planning service is free of charge. Please contact your sales agent or the Planning Department directly, at V&B Fliesen GmbH Objektplanung - Technik + Gestaltung Herr Marco Warschburger Rotensteiner Weg D-6666 Merzig Tel.: +49 (0)6864-81 245 Fax: +49 (0)6864-81 592 E-Mail: marco.warschburger@vb-fliesen.com 8

Fundamentals of swimming pool construction 1 1 1 1 1 200 200 200 200 200 Position from edge = n x 200 + 101,5 mm Rough shell = n x 200 + 126,5 mm Centre distance = n x 200 mm Finished dimension = n x 200 + 5 mm Position from edge = n x 200 + 101,5 mm Rough shell = n x 200 + 126,5 mm n x 100 + mm XX Rough shell dimension = Finished dimension + 2 x mm ca. 50 The (nominal) length of the functional trims (200 mm) determines a basic linear division for the dimensions of the pool in multiples of 200 mm. As in masonry, this is a break dimension and an additional joint must be included. Special notes: Please specify in your order if you require lattice paper on the front side of mosaic tiles. All system components and trims are made to order for your specific project. The finished length of the pool is therefore calculated as follows: finished length = n x 200 mm + mm The rough shell length is calculated as follows: Rough shell length = finished length + 2 x construction thickness of walls The walls are made of plaster, mortar and tiles = generally mm. The rough shell length is therefore the finished lengh + 50 mm. The position of the drains: position from edge = n x 200 mm + 101.5 mm The axial spacing of the drains is: centre distance = n x 200 mm The pool depth is calculated by: depth = height of trim + n x 100 mm + 5 mm To allow continual and uniform overflow, care must be taken when laying the pool edge that it is perfectly horizontal and level. According to the German Guidelines for pool construction deviations in height of +/- 2 mm are acceptable. The following drawings were produced by the company V&B Fliesen GmbH. The user is responsible for verifying the correctness and suitability of the variant concerned. V&B Fliesen GmbH provides no guarantee and shall not be held liable in this connection. 9

Fundamentals of swimming pool construction Drains The number of drains depends on the size of the pool, the size of the overflow channels and the water circulation, and should be calculated by a water-treatment firm. Approx. 2.5 m can be taken as a general guideline for the centre distance, depending on the overflow system. Drain funnels (available from manufacturers of accessories) should be concreted in to compensate for installation tolerances in the drain piping. Villeroy & Boch tiles supplies drain connectors or whispering drains to connect the tiles around the drain to the piping. These should be ordered separately. As shown in the installation instructions, the tiler should attach the short connector to the drain with epoxy resin. The whispering drain is inserted from above and secured with a rubber seal. A Drain dimensions in mm Art. A B C 01 115 110 86 061 75 90 75 091 155 110 86 071 1 110 86 B Special note: Outlet connectors and whispering drains must be ordered separately. 6 72 65 17 72 65 17 72 65 17 65 8 65 75 100 70 170 65 8 65 90 90 8 108 108 110 120 Art. 962 Whispering drain Ø 65 mm Flange Ø 8 mm Plastic, grey 65 65 75 Art. 2 Whispering drain Ø 90 mm Flange Ø 108 mm Plastic, white Art. 96 Whispering drain Ø 90 mm Flange Ø 108 mm Plastic, white Art. 952 Drain connector Ø 100 mm Plastic, yellow 8 Drain funnel Drain funnel Connection with whispering drain Connection with drain connector 10

Overview of pool edge systems High water level Finnish Pyrmont system Art. 010, Art. 014, Art. 600 Uses (preferable): Outdoor, recreation, sport and teaching pools PRO ARCHITECTURA-colours Article number Material PN00 PN1 PN55 PN56 PN57 PN58 page Finnish overflow system: Pyrmont & St.Moritz Grip trough Art. 010 Glazed vitreous 18 Grip trough with outlet Art. 011 Glazed vitreous 18 Inside corner Art. 012 Glazed vitreous 18 Outside corner Art. 01 Glazed vitreous 18 Grating support Art. 014 Glazed vitreous 18 Inside corner Art. 015 Glazed vitreous 18 Outside corner Art. 016 Glazed vitreous 18 Angle grating support Art. 017 Glazed vitreous 18 Edge tile Art. 050 Glazed vitreous 0 Inside corner Art. 051 Glazed vitreous 0 Outside corner Art. 052 Glazed vitreous 0 Channel piece Art. 600 Glazed vitreous 18 Channel piece Art. 601 Glazed vitreous 18 with outlet Channel piece, Art. 602 Glazed vitreous 18 half length Inside corner Art. 604 Glazed vitreous 18 Outside corner Art. 605 Glazed vitreous 18 Pool edge Ladder Art. 055 Glazed vitreous 1 11

Overview of pool edge systems High water level Wiesbaden system Art. 670, Art. 690, Art. 680 Uses (preferable): Indoor, outdoor, recreation, fun and hotel pools PRO ARCHITECTURA-colours System trim Article number Material PN00 PN04 PN12 PN1 page Wiesbaden small overflow channel Channel piece Art. 670 Glazed vitreous 22 Channel piece Art. 671 Glazed vitreous 22 with outlet Channel piece, Art. 672 Glazed vitreous 22 half length Inside corner Art. 674 Glazed vitreous 22 Outside corner Art. 675 Glazed vitreous 22 Channel piece, Art. 676 Glazed vitreous 22 left end tile Channel piece, Art. 677 Glazed vitreous 22 right end tile Wiesbaden large overflow channel Channel piece Art. 690 Glazed vitreous 20 Channel piece Art. 691 Glazed vitreous 20 with outlet Channel piece, Art. 692 Glazed vitreous 20 half length Inside corner Art. 694 Glazed vitreous 20 Outside corner Art. 695 Glazed vitreous 20 Channel piece, Art. 696 Glazed vitreous 20 left end tile Channel piece, Art. 6 Glazed vitreous 20 right end tile 12

Overview of pool edge systems High water level PRO ARCHITECTURA-colours System trim Article number Material PN00 PN04 PN12 PN1 page Wiesbaden large overflow channel with mosaic recess Channel piece Art. 680 Glazed vitreous 21 Channel piece Art. 681 Glazed vitreous 21 with outlet Channel piece Art. 682 Glazed vitreous 21 half length Inside corner Art. 694 Glazed vitreous 21 Outside corner Art. 685 Glazed vitreous 21 Berlin overflow channel Art. 540 Uses (preferable): Indoor, outdoor, recreation, fun and hotel pools Berlin overflow channel Pool running edge Art. 540 Glazed vitreous 2 Pool running edge, Art. 542 Glazed vitreous 2 half length Inside corner Art. 544 Glazed vitreous 2 Outside corner Art. 545 Glazed vitreous 2 Accessories Whispering drain Art. 2 Plastic, white 10 Drain connector Art. 952 Plastic, yellow 10 Whispering drain Art. 96 Plastic, white 10 1

Overview of pool edge systems Low water level Wiesbaden system Art. 660, Art. 60 Uses (preferable): Indoor, outdoor and therapy pools Therapy system Art. 660 Uses (preferable): Therapy pools PRO ARCHITECTURA-colours System trim Article number Material PN00 PN04 PN12 PN1 page Wiesbaden small overflow channel & Therapy system Channel piece Art. 660 Glazed vitreous Channel piece Art. 661 Glazed vitreous with outlet Channel piece, Art. 662 Glazed vitreous half length Inside corner Art. 664 Glazed vitreous Outside corner Art. 665 Glazed vitreous Channel piece, Art. 666 Glazed vitreous left end tile Channel piece, Art. 667 Glazed vitreous right end tile Wiesbaden large overflow channel & Therapy system Channel piece Art. 60 Glazed vitreous 24 Channel piece Art. 61 Glazed vitreous 24 with outlet Channel piece, Art. 62 Glazed vitreous 24 half length Inside corner Art. 64 Glazed vitreous 24 Outside corner Art. 65 Glazed vitreous 24 Channel piece, Art. 66 Glazed vitreous 24 left end tile Channel piece, Art. 67 Glazed vitreous 24 right end tile 14

Overview of pool edge systems Low water level System trim Article number Material page Accessories Whispering drain Art. 962 Plastic, white 10 Whispering drain Art. 96 Plastic, white 10 Whispering drain Art. 2 Plastic, white 10 Drain connector Art. 952 Plastic, yellow 10 Skimmer system Art. 650 Uses (preferable): Private pools PRO ARCHITECTURA-colours PN00 PN04 PN12 PN1 PN1 Pool running edge Pool running edge Art. 650 Glazed vitreous 26 Pool running edge, Art. 652 Glazed vitreous 26 half length Inside corner Art. 654 Glazed vitreous 26 Outside corner Art. 655 Glazed vitreous 26 15

Overview of pool edge systems Curved and cove base ceramic beading Curved and cove base ceramic beading Art. 120, Art. 160 Uses (preferable): Indoor, outdoor, recreation, fun and hotel pools PRO ARCHITECTURA-colours System trim Article number Material PN00 PN04 PN12 PN1 page Small curved ceramic beading Curved ceramic beading Art. 121 Glazed vitreous 2 r=0 Curved ceramic beading Art. 122 Glazed vitreous 2 r=0, half length Curved ceramic beading Art. 124 Glazed vitreous 2 Outside corner Curved ceramic beading Art. 1 Glazed vitreous 2 Inside corner Small cove base ceramic beading Cove base ceramic beading Art. 120 Glazed vitreous 2 r=20 Cove base ceramic beading Art. 12 Glazed vitreous 2 Outside corner Cove base ceramic beading Art. 126 Glazed vitreous 2 Inside corner Large curved ceramic beading Curved ceramic beading Art. 161 Glazed vitreous 2 r=55 Curved ceramic beading Art. 162 Glazed vitreous 2 r=55, half length Curved ceramic beading Art. 164 Glazed vitreous 2 Outside corner Curved ceramic beading Art. 165 Glazed vitreous 2 Inside corner Large cove base ceramic beading Cove base ceramic beading Art. 160 Glazed vitreous 2 r=45 Cove base ceramic beading Art. 16 Glazed vitreous 2 Outside corner Cove base ceramic beading Art. 166 Glazed vitreous 2 Inside corner 16

Overview of pool edge systems Channel in the pool rim Channel in the pool rim Art. 620 Uses (preferable): Drainage channels, pool rims PRO ARCHITECTURA-colours System trim Article number Material PN00 PN09 PN12 PN1 page Ceramic channel in the pool rim Channel piece Art. 620 Glazed vitreous 4 Channel piece Art. 621 Glazed vitreous 4 with outlet Channel piece, Art. 622 Glazed vitreous 4 half length Inside corner/ Art. 624 Glazed vitreous 4 Outside corner End piece Art. 626 Glazed vitreous 4 17

Pool edge systems in detail High water level/ Finnish overflow system 1 1 15 Art. 010 Grip trough PN55, PN56, PN57, PN58 1 1 15 Art. 011 Grip trough with outlet PN55, PN56, PN57, PN58 Applications Material Actual size Joints approx. Surface Finish Glaze Packing Calculation unit Pool edge - indoors / outdoors Glazed / unglazed vitreous see diagrams mm formed, rough uni-coloured matt Piece Piece Matching wall tiles Pro Architectura 1 Art. 012 Inside corner PN55, PN56, PN57, PN58 1 1 Art. 01 Outside corner PN55, PN56, PN57, PN58 Special points Underwater edges such as steps or the front edge of the Finnish system must be accentuated with a stripe of a different colour (PN04, PN12). Depending on requirements, the following colour combinations are available: PN55 = PN04 + PN1 (dark blue and aquamarine) PN56 = PN12 + PN1 (black and aquamarine) PN57 = PN00 + PN12 (white and black) PN58 = PN00 + PN04 (white and dark blue) 15 1 15 Art. 014 Grating support PN00, PN1 40 122 180 15 50 65 1 170 65 15 40 Art. 015 Inside corner PN00, PN1 In Germany, Finnish overflow systems are expected to satisfy the following requirements: The pool edge must offer something to hold onto (grip). The grip must be 15 mm high/deep. The grip must be situated within 100 mm of the vertical wall of the pool. The rear side of the grip should be as vertical as possible. The top of the grip must be accentuated by means of a stripe of contrasting colour measuring at least 2.5 cm across. The slope of the washover incline must be max. 10 %, and the surface finish must answer the description of slip resistance category C. 1 1 1 180 15 50 65 20 Art. 016 Outside corner PN00, PN1 Art. 017 Angle grating support PN00 180 94 50 15 65 PN55 = PN04 dark blue + PN1 aquamarine PN56 = PN12 black + PN1 aquamarine 1 170 Art. 600 Channel piece PN00 170 180 180 65 Art. 601 Channel piece with outlet PN00 PN57 = PN00 white + PN12 black PN58 = PN00 white + PN04 dark blue Art. 602 Channel piece, half length PN00 Art. 604 Inside corner PN00 1 1 Art. 605 Outside corner PN00 18

Pool edge systems in detail High water level/ Finnish overflow system 0 Water level ±0.00 Art. 010 Art. 215 "C" Art. 014 Art. 017 14 Art. 214 "B" 28 15 Inclination 10% 270 Art. 171 or Art. 215 8 Capillary breaking joint filler Bonded Waterproofing Art. 21 Art. 600 8 195 00 0 175 20 Water level ±0.00 Art. 010 Art. 014 Art. 017 Art. 2612 "B" Art. 2612 "B" Inclination 168 Art. 171 or Art. 215 6 Art. 201 4 8 l/m 147 Art. 10 0 1 4 0 96 11 00 Reaction resin filler 0 46,0 l/m 0 50 1 5 0 9 10 192 Watertight concrete 4 18 15 Capillary breaking joint filler Bonded waterproofing 0 2 208 Watertight concrete High water level - overflow channel with moulded trims Uses (preferable): Indoor, outdoor, recreation, fun and hotel pools 19

Pool edge systems in detail High water level/large overflow channel Wiesbaden 200 1 0 18 222 00 0 0 110 60 Applications Pool edge - indoors / outdoors Material Glazed / unglazed vitreous Actual size see diagrams Joints approx. mm Surface formed Finish uni-coloured Glaze matt Packing Piece Calculation unit Piece Art. 690 Channel piece PN00, PN04, PN12, PN1 Matching wall tiles Pro Architectura 00 200 1 155 0 18 222 00 0 60 110 0 Art. 691 Channel piece with outlet PN00, PN04, PN12, PN1 Water level ±0.00 Art. 690 200 5 1 155-0.05 2,8 l/m 00 Capillary breaking joint filler 15 0 Art. 2612 "B" Art. 2612 "B" Inclination Bonded waterproofing Art. 107 200 110 0 60 0 222 0 18 00 140 0 110 60 00 0 00 0 18 222 00 95 00 200 1 Reaction resin filler Watertight concrete Art. 692 Channel piece, half length PN00, PN04, PN12, PN1 1 Art. 694 Inside corner (Mitred pair) PN00, PN04, PN12, PN1 High water level overflow channel with moulded trims Uses (preferable): Indoor, outdoor, recreation, fun and hotel pools 1 1 1 1 Art. 695 Outside corner (Mitred pair, 4 part) PN00, PN04, PN12, PN1 Art. 696 Channel piece, left end tile PN00, PN04, PN12, PN1 Art. 6 Channel piece, right end tile PN00, PN04, PN12, PN1 20

Pool edge systems in detail High water level/large overflow channel Wiesbaden with mosaik recess 200 1 9 21 18 222 291 0 60 0 110 Applications Pool edge - indoors / outdoors Material Glazed / unglazed vitreous Actual size see diagrams Joints approx. mm Surface formed Finish uni-coloured Glaze matt Packing Piece Calculation unit Piece Art. 680 Channel piece PN00, PN04, PN12, PN1 Matching wall tiles Pro Architectura 00 200 1 155 9 21 18 Art. 681 Channel piece with outlet PN00, PN04, PN12, PN1 222 291 0 60 0 110 Water level ±0.00 Art. 680 2 2 2 2 2 2 2 2 2 2 2 24 2 2 2 2 2 2 2 2 2 2 155 60 200 9 0 110 0 222 21 18 291 140 0 110 60 0 00 222 0 18 00 95 00 200 2 2 2-0.05 2,8 l/m 00 Capillary breaking joint filler 15 0 Art. 2612 "B" Art. 2612 "B" Inclination Bonded waterproofing 2 2 Art. 75 Reaction resin filler Art. 682 Channel piece, half length PN00, PN04, PN12, PN1 Watertight concrete 00 Art. 694 Inside corner (Mitred pair) PN00, PN04, PN12, PN1 High water level overflow channel with moulded trims Uses (preferable): Indoor, outdoor, recreation, fun and hotel pools 1 1 1 1 Art. 685 Outside corner (Mitred pair, 4 part) PN00, PN04, PN12, PN1 21

Pool edge systems in detail High water level/small overflow channel Wiesbaden 150 1 0 18 147 2 0 27 78 45 Art. 670 Channel piece PN00, PN04, PN12, PN1 Applications Pool edge - indoors / outdoors Material Glazed / unglazed vitreous Actual size see diagrams Joints approx. mm Surface formed Finish uni-coloured Glaze matt Packing Piece Calculation unit Piece Matching wall tiles Pro Architectura 150 1 116 0 18 147 2 0 27 78 45 Art. 671 Channel piece with outlet PN00, PN04, PN12, PN1 Water level ±0.00 Art. 670 150 5 2 47 47 47 47 20 47 47 47 1 Capillary breaking joint filler Art. 2706 "B" -0.02 Inclination 11,7 l/m 100 0 Bonded waterproofing 150 27 78 45 0 18 147 2 0 Art. 201 105 27 78 45 2 0 147 18 2 0 2 Art. 672 Channel piece, half length PN00, PN04, PN12, PN1 Reaction resin filler Watertight concrete Art. 674 Inside corner (Mitred pair) PN00, PN04, PN12, PN1 00 170 2 150 High water level overflow channel with moulded trims 1 1 Uses (preferable): Indoor, outdoor, recreation, fun and hotel pools 1 1 Art. 675 Outside corner (Mitred pair, 4 part) PN00, PN04, PN12, PN 1 Art. 676 Channel piece, left end tile PN00, PN04, PN12, PN1 Art. 677 Channel piece, right end tile PN00, PN04, PN12, PN1 22

Pool edge systems in detail High water level/overflow channel Berlin 100 1 5 80 10 45 55 1 Art. 540 Pool running edge PN00, PN04, PN12, PN1 Applications Pool edge - indoors / outdoors Material Glazed / unglazed vitreous Actual size see diagrams Joints approx. mm Surface formed Finish uni-coloured Glaze matt Packing Piece Calculation unit Piece Matching wall tiles Pro Architectura 100 55 1 45 5 80 10 Art. 542 Pool running edge, half length PN00, PN04, PN12, PN1 Water level ±0.00 5 00 Art. 540 Art. 10 or Art. 171 4 Art. 10 6 Art. 017 Art. 2248 "B" Capillary breaking joint filler Inclination Bonded waterproofing 10 5 80 10 55 45 1 0 4 4 1 8 l/m 0 1 100 147 4 0 Art. 10 Art. 544 Inside corner PN00, PN04, PN12, PN1 Art. 21 Reaction resin filler 96 11 11 208 Watertight concrete 1 1 Art. 545 Outside corner PN00, PN04, PN12, PN1 00 High water level overflow channel with moulded trims Uses (preferable): Indoor, outdoor, recreation, fun and hotel pools 2

Pool edge systems in detail Low water level/large overflow channel Wiesbaden 150 1 0 166 29 2 12 27 Art. 60 Channel piece PN00, PN04, PN12, PN1 Applications Pool edge - indoors / outdoors Material Glazed vitreous Actual size see diagrams Joints approx. mm Surface formed Finish uni-coloured Glaze matt Packing Piece Calculation unit Piece Matching wall tiles Pro Architectura 487 150 112 5 12 5 5 147 147 147 20 147 27 Art. 650 Art. 2405 "B" 1 166 29 150 0 0 166 29 2 2 Art. 61 Channel piece with outlet PN00, PN04, PN12, PN1 12 27 Water level ±0.00 260 Art. 60 150 160 100 26 Art. 107 112 18,7 l/m Capillary breaking joint filler 150 Bonded waterproofing Art. 62 Channel piece, half length PN00, PN04, PN12, PN1 150 27 12 2 0 166 29 2 1 5 1 200 2 Art. 107 Watertight concrete Reaction resin filler Art. 64 Inside corner (Mitred pair) PN00, PN04, PN12, PN1 00 170 2 150 Low water level overflow channel with moulded trims Uses (preferable): Indoor, outdoor, recreation, fun and hotel pools 1 1 1 1 Art. 65 Outside corner (Mitred pair, 4 part) PN00, PN04, PN12, PN1 Art. 66 Channel piece, left end tile PN00, PN04, PN12, PN1 Art. 67 Channel piece, right end tile PN00, PN04, PN12, PN1 24

Pool edge systems in detail Low water level/small overflow channel Wiesbaden 100 1 0 75 26 94 145 105 Art. 660 Channel piece PN00, PN04, PN12, PN1 Applications Pool edge - indoors / outdoors Material Glazed vitreous Actual size see diagrams Joints approx. mm Surface formed Finish uni-coloured Glaze matt Packing Piece Calculation unit Piece Matching wall tiles Pro Architectura 100 75 105 7 1 75 0 26 94 145 5 5 147 Art. 650 147 20 Art. 2405 "B" 147 100 Art. 661 Channel piece with outlet PN00, PN04, PN12, PN1 0 75 26 94 145 105 Water level ±0.00 Art. 660 100 0 5 99 100 5 Art. 107 75 6,5 l/m Capillary breaking joint filler 100 Bonded waterproofing Art. 662 Channel piece, half length PN00, PN04, PN12, PN1 1 120 10 145 26 94 145 0 105 75 Art. 107 Watertight concrete 1 Reaction resin filler Art. 664 Inside corner (Mitred pair) PN00, PN04, PN12, PN1 00 Low water level overflow channel with moulded trims 100 50 145 Uses (preferable): Indoor, outdoor, recreation, fun and hotel pools 1 1 Art. 665 Outside corner (Mitred pair) PN00, PN04, PN12, PN1 Art. 666 Channel piece, left end tile PN00, PN04, PN12, PN1 Art. 667 Channel piece, right end tile PN00, PN04, PN12, PN1

Pool edge systems in detail Low water level Pool edge piece 100 1 5 155 180 40 5 Applications Pool edge - indoors / outdoors Material Glazed / unglazed vitreous Actual size see diagrams Joints approx. mm Surface formed Finish uni-coloured Glaze matt Packing Piece Calculation unit Piece Art. 650 Pool running edge PN00, PN04, PN12, PN1, PN1 Matching wall tiles Pro Architectura 100 40 5 5 155 180 Art. 652 Pool running edge, half length PN00, PN04, PN12, PN1, PN1 5 5 Art.2200 "B" Art. 650 40 5 100 145 180 5 155 180 ±0.00 Art. 201 100 1 5 Water level 1 Skimmer according manufacturers instructions Art. 654 Inside corner (Mitred pair) PN00, PN04, PN12, PN1, PN1 1 1 Art. 655 Outside corner (Mitred pair) PN00, PN04, PN12, PN1, PN1 Low water level Skimmer system Uses (preferable): Private pools Note: To ensure swimming pool water of hygienic quality, the water is to be treated and disinfected in accordance with DIN 1964-1 (treatment of water for swimming pools). To prevent fungal attack, the surfacing is to undergo thorough cleaning once annually, replacing the entire filling of water. 26

Pool edge systems in detail High water level/ Finnish overflow system - Open channel 677 20 Water level ±0.00 15 Art. 010 0 50 22 28-0.02 Art. 2702 "C" 50 0 Art. 2200 "B" Bonded waterproofing +0.02 55 1 1 1 Reaction resine filler Art. 107 Watertight concrete 00 High water level/ St. Moritz system The rounded-off pool border is higher than the pool surround. The water level is approximately 50-60 cm above the pool surround. The water flows over the pool border, running down the outside and into the overflow channel, the top of which is flush with the pool surround. The overflow is executed either as a shallow, open trough or as a grate-covered, tiled, channel. Small format tiles are preferable. With deference to possible erosion, epoxy resin should be used for filling the joints. 585 Art. 75 0 4 2 Art. 010 Water level ±0.00 1 1 15 Art. 215 Reaction resin filler 170 Art. 2641 "B" Art. 017 Art. 017 Art. 215 Art. 10 0 115 0 147 70 290 1 Inclination -0.59 1 Bonded waterproofing Capillary breaking joint filler 1 Watertight concrete 27

Special designs Therapy pools In Germany, the design and construction of medicinal baths is subject to the following basic rules: The minimum dimensions for therapy pools are x 4 m. The minimum water depth is 0.5 m for children and 0.8 m for adults. The maximum water depth is 1.5 m. The pool must have an overflow channel running along all its sides. Skimmers are not acceptable for hygienic reasons. The slope of the pool s floor should ideally be constant, and should not exceed 4%. The pool must have an overflow channel on at least one side and one end. As a rule, the therapist s gallery should run along one side of the pool and have a minimum width of 75 cm and a minimum depth of 80 cm. A handrail or ledge must be provided at the edge of the pool (water level). The steps must be at least 60 cm wide. The maximum slope for ramps is 15 %. 12 5 2 2 5 5 5 48 48 48 5 5 Art. 161 +0.09 Art. 709 Water level ±0.00 Art. 060 100 0 5 5 5 6,5 l/m 100 211 5 5 5 Art. 201 120 192 7 6 145 Art. 201 4 5 5 5 5 10 5 19 15 1 Capillary breaking joint filler 5 2 Reaction resin filler Watertight conrete Art.161 Art. 50 (cut) Polystyrene strip -0.70 Art. 120 Art. 2200 "B" 294 1 2 = Elastic joint sealant 28

Special designs Therapy pools 12 288 +0.1 Water level ±0.00 100 0 5 Capillary breaking joint filler 75 6,5 l/m 1 10 77 Art. 660 5 2 60 Art. 201 Art. 75 12 147 147 5 260 145 Reaction resin filler Watertight concrete 4-0.77 Bonded waterproofing Art. 2404 "B" 1 2 4 = Elastic joint sealant 29

Pool edge systems in detail - Fixtures Pool access steps 15 47 1 Art. 050 Edge tile PN55, PN56, PN57, PN58 Applications Material Actual size Joints approx. Surface Finish Glaze Packing Calculation unit Matching wall tiles Pool edge - indoors / outdoors Glazed / unglazed vitreous see diagrams mm formed, rough uni-coloured matt Piece Piece Pro Architectura 15 15 47 1 Art. 051 Edge tile, inside corner PN55, PN56, PN57, PN58 1 Art. 052 Edge tile, outside corner PN55, PN56, PN57, PN58 Special points Underwater edges such as steps or the front edge of the Finnish system must be accentuated with a stripe of a different colour (PN04, PN12). Depending on requirements, the following colour combinations are available: PN55 = PN04 + PN1 (dark blue and aquamarine) PN56 = PN12 + PN1 (black and aquamarine) PN57 = PN00 + PN12 (white and black) PN58 = PN00 + PN04 (white and dark blue) In Germany, Finnish overflow systems are expected to satisfy the following requirements: The pool edge must offer something to hold onto (grip). The grip must be 15 mm high/deep. The grip must be situated within 100 mm of the vertical wall of the pool. The rear side of the grip should be as vertical as possible. The top of the grip must be accentuated by means of a stripe of contrasting colour measuring at least 2.5 cm across. The slope of the washover incline must be max. 10 %, and the surface finish must answer the description of slip resistance category C. PN55 = PN04 dark blue + PN1 aquamarine PN56 = PN12 black + PN1 aquamarine PN57 = PN00 white + PN12 black PN58 = PN00 white + PN04 dark blue 62 0 2 Water level ±0.00 Art. 246 "C" Art. 21 160 Art. 010 158 24 Art. 014 Art. 171 or Art. 215 8 Art. 2121 "B" or Art. 2122 "B" Bonded waterproofing Kapillarsperre Inclination Art. 246 "C" 15 Art. 246 "C" Art. 050 "C" -0.2 15 0 9 Art. 050 "C" -0.16 00 0 Reaction resin filler 0 4 8 l/m 147 Art. 10 4 0 21 208 200 0 195 96 112 Art. 050 "C" -0.48 0 9 Top concrete layer Watertight concrete 00 00 00 0 0

Pool edge systems in detail - Fixtures Ladder 80 Art. 055 Ladder 1 50 Applications Ladder - indoors / outdoors Material Glazed vitreous Actual size see diagrams Joints approx. mm Surface formed Finish uni-coloured Glaze matt Packing Piece Calculation unit Piece Matching wall tiles PRO ARCHITECTURA Water level 0 Art. "B" ±0.00 Art. 010 Art. 2702 "C" Art. 014 Art. 017 Inclination Art. 201 Art. 055 06 06 06 00 28 28 15 6 80 2 Inclination max. 10% 80 19 44 272 156 0 Art. 171 or Art. 215 9 l/m Art. 10 106 118 Reaction resin filler Capillary breaking joint filler Bonded waterproofing Art. 201 100 156 Watertight concrete 1

5 5 5 5 1 5 5 5 5 1 5 27 27 5 5 27 5 5 27 5 5 5 27 5 5 27 5 47 47 5 5 5 5 5 27 8 19 1 1 5 4 10 8 19 5 10 4 819 47 47 4 5 4 5 10 4 5 5 Pool edge systems in detail - Fixtures Curved and cove base ceramic beading Art. 161 Curved ceramic beading r=55 PN00, PN04, PN12, PN1 Art. 121 Curved ceramic beading r=0 PN00, PN04, PN12, PN1 Applications Pool edge - indoors / outdoors Material Glazed vitreous Actual size see diagrams Joints approx. mm Surface formed Finish uni-coloured Glaze matt Packing Piece Calculation unit Piece Matching wall tiles PRO ARCHITECTURA Art. 162 Curved ceramic beading r=55, half length PN00, PN04, PN12, PN1 Art. 122 Curved ceramic beading r=0, half length PN00, PN04, PN12, PN1 Art. 164 Curved ceramic beading Outside corner PN00, PN04, PN12, PN1 Art. 124 Curved ceramic beading Outside corner PN00, PN04, PN12, PN1 Art. 165 Curved ceramic beading Inside corner PN00, PN04, PN12, PN1 Art. 1 Curved ceramic beading Inside corner PN00, PN04, PN12, PN1 Art. 160 Cove base ceramic beading r=45 PN00, PN04, PN12, PN1 Art. 120 Cove base ceramic beading r=20 PN00, PN04, PN12, PN1 Art. 16 Cove base ceramic beading Outside corner PN00, PN04, PN12, PN1 Art. 12 Cove base ceramic beading Outside corner PN00, PN04, PN12, PN1 19 5 19 5 19 8 Art. 166 Cove base ceramic beading Inside corner PN00, PN04, PN12, PN1 Art. 126 Cove base ceramic beading Inside corner PN00, PN04, PN12, PN1 2

Pool edge systems in detail - Fixtures Curved and cove base ceramic beading 5 5 5 5 48 00 210 20 155 Water level ±0.00 Art. 709 Art. 161 5 5 5 10 Art. 709-0.05 2,8 l/m Capillary breaking joint filler Art. 690 110 44 Art. 2641 "B" Inclination Bonded waterproofing Art. 2641 "B" 104 82 5 00 Art. 121 Art. 709 Art. 160-0.51 Reaction resin filler Watertight concrete 412 64 82 0 Top concrete layer

Functional trims for pool surrounds Ceramic channel in the pool rim 1 2 Art. 620 Channel piece PN00, PN09, PN12, PN1 Applications Pool rim - indoors / outdoors Material Glazed vitreous Actual size see diagrams Joints approx. mm Surface formed Finish uni-coloured Glaze matt Packing Piece Calculation unit Piece Matching wall tiles PRO ARCHITECTURA 48 5 2 1 2 2 2 Art. 622 Channel piece, half length PN00, PN09, PN12, PN1 Art. 2200 "B" Inclination Art. 620 "B" Inclination Bonded waterproofing Art. 621 Channel piece with outlet PN00, PN09, PN12, PN1 Pool surrounding concrete construction Art. 624 Inside corner/outside corner PN00, PN09, PN12, PN1 1 Art. 626 End piece PN00, PN09, PN12, PN1 4

Swimming pool renovation Thanks to its decades of experience, Villeroy & Boch tiles is the competent partner for the construction of new and restoration of existing swimming pools. Our company offers you a consultation and planning service that will assist you in all stages of project implementation. Please talk to the Villeroy & Boch tiles sales representatives or to the relevant department Water level ±0.00 Art. 670 5 150 1-0.02 2 47 47 47 47 20 47 47 47 11,7 l/m Capillary breaking joint filler 100 0 2 172 Art. 2706 "B" Inclination Bonded waterproofing directly. Art. 201 Bonded waterproofing When renovating swimming baths, it is often necessary to install a composite seal directly under the tile covering. 00 When renovation swimming pools, it often may be necessary to install a composite seal directly under the tile covering. 26 175 20 Water level ±0.00 Art. 010 Art. 017 Art. 2612 "B" Inclination Art. 2612 "B" Art. 21 4 15 Art. 171 or Art. 215 4 l/m Art. 600 8 0 50 4 15 92 102 00 18 0 Capillary breaking joint filler Bonded waterproofing 1 194 170 20 Watertight conrete 5

Technical aspects of application for swimming pools Static systems, movement joints The pool must be structurally independent of the remaining structure. The structural engineer is re sponsible for selecting the static system. His decision dictates the arrangement of movement joints around and, where necessary, within the pool. The following static systems can be used to effect the structural separation of the pool from the remaining structure. Surround formed as single span slab Surround formed as cantilever slab on the pool Surround formed as cantilever slab on the structure Waterproofing of movement joints for overflow systems The movement joint is situated in an area which is exposed to high strain through water. The type of water-proofing to be used for the joint depends on the waterproofing of the pool surround. Nowadays, pool surrounds are usually waterproofed with brushable coatings, so-called alternative waterproofing, in accordance with ZDB leaflet. Water level ±0.00 > 150 Inclination Capillary breaking joint filler Tiles Thin-bed mortar Bonded waterproofing Elastic joint sealant with closed cell rope Sealing tape Sloping screed covered with thermal insulation, protective sheet and reinforced screed Reaction resin filler Watertight concrete 6

Technical aspects of application for swimming pools Pool construction Pools to be clad with tiles are generally made of reinforced concrete as per DIN 1045. In some cases, pools made of stainless steel, e.g. on pleasure cruisers, or plastic can also be lined with vitreous tiles. The following considerations apply exclusively to reinforced waterlight concrete pools. This can be achieved by: using impermeable concrete or waterproofing. After completing the reinforced concrete body of the pool, in order to verify watertightness, the customer is to fill the pool with chlorinated water for test purposes to the level of the rim around the pool (exposed concrete). The outside of freestanding pools should also not be waterproofed until after the leak test. Marking the water level during the leak test provides an excellently accurate line of reference for positioning the ceramic accessories for the overflow without the need for carrying out special additional measurements. Pools made of watertight concrete The pool is made of impermeable concrete in accordance with DIN 1045 and the structural analysis. The concrete must be and remain free of cracks. The following points should be heeded when building the pool: Proper composition of aggregates and accordingly a low water/cement ratio. For practical reasons, pool floors and walls should be at least cm thick and the upturn behind and/ or in front of the drainage channel should be at least 15 cm thick, in the absence of any addi tional sealing. Optimal compaction of freshly poured concrete by means of an immersion vibrator. Appropriate aftertreatment of concrete (by keeping it moist) Minimum strength category of concrete: B. Minimum overlap of reinforcing rods: 5 cm. For pools intended to be filled with aggressive water, e.g. salt water, the bonding agents used should be selected on the basis of a water analysis. It is desirable to pour the floor and walls in a single operation. Should a construction joint between the floor and the walls be necessary, a stop-end joint tape must be inserted. Tiles Elastic joint sealant Stop end joint tape Reinforcement 7

Technical aspects of application for swimming pools Pool construction Pools with composite seal (CS) with ceramic covering As a technical rule for this type of waterproofing see the leaflet from the ZDB Ceramic tiles in swimming pool construction - Advice on planning and implementation. and DIN 18195-7. Materials used: Synthetic mortar mixtures dry layer thickness min. 2.0 mm Reactive resins dry layer thickness min. 1.0 mm or the minimum layer thicknesses as specified in the general building inspectorate test certificates of the respective manufacturer must be observed. Suitable bases Concrete in accordance with DIN 1405 and DIN 4227 Underlay waterproof plaster in accordance with DIN 18550, mortar group P III Levelling screed as bonded levelling screed in accordance with DIN 18560, quality ZE 20 The dimensional accuracy of the backing should correspond with the finished cladding. Considerable unevenness should be compensated for beforehand with underlay waterproof plaster or levelling screed. The base material must be free of abherents, debris, dust, binding agents, efflorescence or other contaminants that could impair adhesion. Concrete surfaces on the pool walls should be sandblasted. Resulting cracks or the movement of existing cracks should not exceed 0.2 mm unless there is proof that the relevant sealant is able to bridge larger cracks. Waterproofing Is to be carried out according to the general building inspectorate test certificates of the respective manufacturer. The thickness of the waterproofing depends on the material used and on the manufacturers specifications. The waterproofing is applied by filling, smoothing, rolling or spraying onto the cleaned substrate. As a rule, the waterproofing has to be applied in at least two work processes in accordance with the manufacturer s instructions. Tiles Thin-bed mortar Bonded waterproofing Sealing tape Closed cell rope Elastic joint sealant At structure joints and corners wherever movements are to be expected, the waterproofing should be reinforced with bonded fabric or sealing collars. Pipes are incorporated in the surface waterproofing by means of a gasket or flange. Floor drains need a wide flange to take the waterproofing. Levelling coat Tiles Thin-bed mortar Bonded waterproofing Sealing tape in corner Elastic joint sealant Closed cell rope Insulation strip Screed Screed Watertight concrete Watertight concrete Waterproofing on structure joint Waterproofing at wall/floor joint 8

Technical aspects of application for swimming pools Ceramic claddings In principle all types of tiling belong to one of the following groups: Bonded claddings Floating claddings Differentiation is necessary with deference to: The properties of the finished cladding The anticipated stress levels in the cladding construction The size of sections and the location and execution of expansion/structural joints. Bonded claddings Bonded claddings are based on the principle of frictional connection, i.e. no movement is possible between the ceramic tiles and the solid base, much like in a rein forced concrete component. The conventional setting method involves the use of bedding mortar, while the thin bed method in accordance with DIN 18157 relies on an adhesive to effect the bond. To achieve a good bond, the base material must be free of the following: residue and debris such as wood, metal, formwork lube or other contaminating layers that could impair adhesion cracks or efflorescence considerable unevenness too smooth a surface. Movement joints should be positioned at the edges and at existing structural joints. Concrete Bonding course Bonded screed (Levelling course) Concrete Thin-bed mortar Thin-bed mortar (acc. DIN 18157) (acc. DIN 18157) Tiles Tiles Concrete Bonding course Thick-bed mortar (Levelling course) Tiles Floating claddings A floating cladding is when the cladding is separated from the backing by insulation, foils, oil-impregnated paper or the like in accordance with DIN 18195. Concrete Separation layer (double layer) Reinforced screed (local distribut. course) Thin-bed mortar (acc. DIN 18157) Tiles Concrete Bonded waterproofing (acc.w. DIN 18195) Separation layer (single layer) Reinforced screed (burden-sharing course) Thin-bed mortar (acc. DIN 18157) Tiles Concrete Thermal insulation Separation layer (double layer) Reinforced screed (local distribut. course) Thin-bed mortar (acc. DIN 18157) Tiles Floating claddings 9

Technical aspects of application for swimming pools Ceramic claddings Pool claddings In the case of a swimming pool made of impermeable concrete the tiles are attached by means of the BONDED CLADDING principle. VOB-DIN 1852 Working with tiles and slabs applies for bonded cladding in mortar (so-called conventional or thick bed tiling) DIN 18157 Tiling ceramic coverings using the thin bed method applies for thin bed tiling. DIN 18550 Plaster applies for screeds, DIN 18560 Part The use of screeds bonded screeds. If the backing is as level as the finished cladding is expected to be, the tiles can be fixed directly to the concrete by the thin bed method. In general, however, it is necessary to compensate for a certain amount of unevenness. This is done by applying an underlay of waterproof plaster of mortar group III, preferably pure cement plaster. The tiles are attached to the prepared backing with a thin bed of hydraulic mortar in accordance with DIN 18156, Part 2. When fixing the tiles directly on to the shotcrete with a cement-based mortar, the back of the vitreous tiles must first be powdered lightly with cement or coated with cement-based grout. Most serious damage resulting from the failure of the bond between the tiles and the backing is caused by shear stresses building up in the interface. Shear stress occurs most often when the young concrete is tiled before it has finished shrinking. Note: To ensure swimming pool water of hygienic quality, the water is to be treated and disinfected in accordance with DIN 1964-1 (treatment of water for swimming pools). To prevent fungal attack, the surfacing is to undergo thorough cleaning once annually, replacing the entire filling of water. 40

Technical aspects of application for swimming pools Ceramic claddings Floor and wall claddings in wet rooms Floor claddings which are classified as having a high exposure to moisture require waterproofing and that the floors slope towards the drains. Ths slope of the waterproofing layer corresponds to that of the finished tiling. For ceramic tiles a slope of 1 2 % is usually sufficient. In showering rooms the floor in the vicinity of the showers should slope at a % gradient. Screed Tiles Thin-bed mortar Bonded waterproofing Sealing tape Edge protection bead Closed cell rope Elastic joint sealer Bonded waterproofing The waterproofing must extend over movement joints. Permalastic sealing strips should be used for this purpose. (Figure 1) Watertight concrete Drains are to be integrated into the surface waterproofing by means of a flange or gasket. (Figure 2) The level of the floor at the transition between wet and dry rooms can be the same. The transition should, however, not lie within the splash area and the rooms should be separated by a door. The floor of the wet room should slope sufficiently towards the drain. Figure 1: Waterproofing on screed joint Screed Glass fibre fabric collar Bonded waterproofing Reinforcing collar Thin-bed mortar Polymer concrete collar Tiles inclined inclined Pipes and tap fittings that penetrate wall claddings are integrated into the surface waterproofing by means of a press-on flange. Figure 2: Waterproofing connection at drain 41

Technical aspects of application for swimming pools Ceramic claddings Ceramic tiles on underfloor heating Screeds on an insulating layer and heated screeds should be reinforced. These screeds are to be divided into sections by section boundary joints: in unheated screeds maximum 60 m 2 in size with a maximum edge length of 8 m and in heated screeds maximum 40 m 2 in size with a maximum edge length of 6.5 m. Compact sections should be created wherever possible. Structural joints should be taken on in the same width and in the same location. The screed sections should also be subdivided at doorways and wall projections. The heating pipes should not cross the section joints in heated screeds where possible. If this should prove necessary, 00 mm long pipe sleeves should be used. Heating conductor Pipe sleeve Bonded waterproofing Sealing tape Closed cell rope Elastic joint sealant Movement in heated and unheated floating coverings Movement joint in heated claddings. 42

Pro Architectura Colours Glazed vitreous EN 14411-BI b Walls and floors Glazed porcelain stoneware EN 14411-BI a Walls and floors Neutral Line PN00 z white PN01 r green PN09 z grey % PN05 z yellow PN02 r dark green PN10 r grey 50% PN06 t orange PN0 r blue PN11 r grey 75% PN07 r red PN04 r dark blue PN12 r black PN08 r dark red vilbostone porcelain stoneware EN 14411-BI a Floors GRANIFLOOR 911H 91H 91M 91D PN80 PN81 PN82 PN8 PN84 Glazed vitreous EN 14411-BI b / Glazed porcelain stoneware EN 14411-BI a Walls and floors aquamarine Line turquoise Line emerald Line jade Line beryl Line citrine Line topaz Line amber Line carneol Line light PN1 t PN16 t PN19 t PN22 t PN z PN28 z PN1 z PN4 t PN7 t medium PN14 t PN17 r PN20 r PN2 r PN26 z PN29 z PN2 z PN5 t PN8 t dark PN15 t PN18 r PN21 r PN24 r PN27 z PN0 r PN t PN6 r PN9 t vilbostone porcelain stoneware EN 14411-BI a Floors PN85 PN86 PN87 PN88 PN89 PN90 PN91 PN92 PN9 4

Pro Architectura Overview of products 1 Glazed vitreous 2 Glazed porcelain stoneware 2.5 x 2.5 cm Art. 75 2 2.5 x 2.5 cm Art. 945 2 5 x 5 cm Art. 709 1 5 x 5 cm Art. 845 1 ~ S R9 ~ S R10 f B L ~ S R9 ~ S R10 f B 10 x 10 cm Art. 201 1 10 x 10 cm Art. 245 1 10 x 10 cm Art. 246 1 10 x 20 cm Art. 21 1 L ~ ~ S R10 f B ~ f C L ~ f B 10 x 20 cm Art. 214 1 10 x 20 cm Art. 215 1 10 x 0 cm Art. 50 1 15 x 15 cm Art. 10 1 L ~ f C L ~ L ~ L ~ 20 x 20 cm Art. 217 1 20 x 20 cm Art. 107 1 0 x 0 cm Art. 181 1 0 x 60 cm Art. 65 2 * L ~ f B L ~ L ~ } ~ 60 x 60 cm Art. 66 2 * Multi-purpose trims 1 2 x 10 cm Art. 2 2 x 10 cm Art. 294 } ~ ~ Shower tray construction system Sinus 1 10 x 10 cm Art. 007 10 x 10 cm Art. 009 Functional trims 1 10 x 10 cm Art. 29 2 x 10 cm Art. 295 2 x 10 cm Art. 296 S R10 f B z ~ ~ Sinus 1 5 x 10 cm Art. 570 5 x 5 cm Art. 571 10 x 10 cm Art. 572 5 x 10 cm Art. 585 5 x 10 cm Art. 586 5 x 5 cm Art. 587 5 x 10 cm Art. 57 5 x 10 cm Art. 574 10 x 10 cm Art. 575 10 x 10 cm Art. 588 5 x 10 cm Art. 589 10 x 10 cm Art. 592 5 x 10 cm Art. 59 10 x 10 cm Art. 594 10 x 10 cm Art. 576 5 x 5 cm Art. 577 5 x 5 cm Art. 578 ~ S R10 f B z S R10 f B z S R10 f B z 44

vilbostone unglazed porcelain stoneware 2.5 x 2.5 cm Art. 2702 5 x 5 cm Art. 2706 10 x 10 cm Art. 2200 15 x 15 cm Art. 2405 ~ S R10 f C ~ S R10 f B ~ S R10 f B ~ S R10 f B 15 x 15 cm Art. 2404 15 x 15 cm Art. 2215 GRANIFLOOR 15 x 15 cm Art. 2217 GRANIFLOOR 15 x 15 cm Art. 2219 GRANIFLOOR ~ S R10 f B ~ S R10 f B ~ S R11 f B ~ S R12 V4 f B 20 x 20 cm Art. 2248 20 x 20 cm Art. 2604 20 x 20 cm Art. 2600 20 x 20 cm Art. 22 GRANIFLOOR GRANIFLOOR ~ S R10 f B ~ S R10 f B ~ S R10 f B ~ S R11 f B 20 x 20 cm Art. 2 0 x 0 cm Art. 221 0 x 0 cm Art. 2214 0 x 60 cm Art. 2216 GRANIFLOOR ~ S R12 V4 f B ~ S R10 f A GRANIFLOOR ~ S R9 GRANIFLOOR } ~ S R9 60 x 60 cm Art. 2014 Shower tray construction system 5 x 5 cm Art. 271 5 x 5 cm Art. 2765 Shower tray construction system 10 x 10 cm Art. 2607 10 x 10 cm Art. 2609 } ~ S R9 GRANIFLOOR ~ S R10 f B 5 x 5 cm Art. 2772 ~ S R10 f B 2 x 10 cm Art. 207 10 x 10 cm Art. 2072 2 x 10 cm Art. 2074 10 x 15 cm Art. 2498 10 x 20 cm Art. 2495 ~ S R10 f B ~ S R10 f B * = EU Ecolabelled products L = One glazed edge ~ = Frostproof in acc. with DIN EN ISO 10545-12 S R9, S R10, S R11, S R12 V4 = Anti-slip in workshop areas f A, B, C = Anti-slip in barefoot areas r t z = Wear resistance group (EN ISO-10545-7) V = Surface seal 45

46 Notes

V&B Fliesen GmbH Rotensteiner Weg D-6666 Merzig E-Mail: info@vb-fliesen.com 10/12 Shades and dimensions subject to the usual tolerances. We reserve the right to make technical modifications to the range and alter colours. WWW.VILLEROY-BOCH.COM