1 TC-IIS Series Up to 11 LPM Free Flow TC-IIS Miniature Diaphragm Pumps are a series of brush and brushless DC motor driven pumps which are tailored to meet the specific application performance requirements. The innovative compact designs incorporate leading edge technologies that allow them to operate more efficiently than existing pump designs. TC-IIS Pumps offer multiple component configurations allowing them to be used for either vacuum, pressure, or alternating vacuum and pressure operations. TC-IIS is ideal for compact, high flow, wide pressure ranges, long-life, low noise applications. Typical Applications Patient Monitoring Compression Therapy Hemodialysis Peritoneal Dialysis Respiratory Care Wound Therapy Medical/Training Mannequins Degassing Product Specifications Physical Properties Operating Environment 1 : 1 to 2 F (5 to 5 C) Storage Environment: - to 2 F (- to 1 C) Media: Air, Argon, Helium, Nitrogen, Oxygen, and other non-reacting gases Humidity: % Relative Humidity Noise Level 2 : As low as 5 d @ in ( cm) Muffler recommended for additional noise reduction (see accessories) Pump Assembly Rated Life 3 : PMDC Iron Core rush - 3, hrs - 1, hrs (High Torque) - 1, hrs - 1, hrs Weight:. oz. (227 g) PMDC Iron Core rush 6. oz. (17 g) 11.6 oz. (3 g) (High Torque). oz. (25 g) Features The TC-IIS Series pump sets the highest benchmark for servicefree performance with our unique brushless DC motor design and advanced proprietary diaphragm elastomer. Incorporating the lightweight EZ Mount accessory facilitates simple system assembly while dampening vibration and reducing noise levels. The TC-IIS maximizes flexibility by offering several mount options, Our 1% oil and grease-free pump and compressor design maintains the purity of your system and are commonly used in FDA-approved systems. RoHS compliant. Electrical Motor Type (DC): PMDC Iron Core rush, (High Torque), Nominal Motor Voltages : 6,, or VDC Other voltages available upon request Electrical Termination: PMDC Iron Core rush: 22 AWG Wire Leads, Length 1 (25 mm) Motor: 22 AWG Wire Leads, Length (5 mm) Motor (High Torque): 22 AWG Wire Leads, Length (5 mm) : 22 AWG Wire Leads, Length (5 mm) Current Range 5 : - 1 ma Wetted Materials Diaphragm: EPDM, AEPDM, FKM Valves: EPDM, FKM Pump Head: Vectra (Liquid Crystal Polymer) Pneumatic Head Configuration: Dual Maximum Unrestricted Flow: 6 LPM (Series) 11 LPM (Parallel) Pressure Range: - ( - 3.31 bar) Series - 2 ( - 1.93 bar) Parallel Vacuum Range: - 25 (635 ) (Series) - (5 ) (Parallel) Filtration: microns - recommended Efficiency at Free Flow 6 PMDC Iron Core rush:.9lpm/watt (PN: D73-21-1) : 1.1LPM/Watt (PN: D713-21-1) : 1.LPM/Watt (PN: D737-23-1) : 1.3LPM/Watt (PN: D119-22-1) * See Appendix A for details.
5 2 Performance Specifications Flow (LPM) TC-IIS - PMDC Iron Core rush Motor TC-IIS - PMDC IRON CORE RUSH MOTOR Vacuum () - Pressure (bar). 1 3.2 6 11.6 2 2.2 6.55 1.3 6.. 5. 1... 3. 6. 2.. 1. 2. TC-IIS Series Power Usage (W) - 1 6 2 2 6 1 Vacuum () - Pressure () Max Flow Max Power Min Flow Min Power - Flow (LPM) TC-IIS - Motor TC-IIS - RUSHLESS SLOTTED MOTOR Vacuum () - Pressure (bar). 1 3.2 11.6 6 2.2 2.55 6.3. 11. 1. 9.. 7. 6. 5.. 3. 2. 1. - Flow (LPM) Vacuum () - Pressure () Max Flow Max Power Min Flow Min Power TC-IIS - Motor. 3.2 1 11.6 6.2.55 2.3 1. 9.. 7. 6. 5.. 3. 2. 1. - TC-IIS - RUSHLESS SLOTLESS MOTOR Vacuum () - Pressure (bar) Vacuum () - Pressure () Max Flow Max Power Min Flow Min Power. 1.. 1.. 1.. 6.. 2. -. 1.. 1.. 6.. 2. - Power Usage (W) Power Usage (W) The above graph represents an example of performance for the pumps series handling air at feet (m) above sea level at 75 F ( C). Performance will vary depending on barometric pressure and media temperature. Curves are representative of standard pump configurations. Pump configurations could be customized for higher or lower flows, depending on specific customer requirements. Please contact Parker Precision Fluidics Applications Engineering for other considerations.
6 3 TC-IIS Series Sizing and Selection TC-IIS Series PMDC Iron Core rush Motor Motor (High Torque) Motor Efficiency Life 1 Cost Noise PMDC Iron Core rush (High Torque) Good etter - Up to 6% motor efficiency at low loads Good - 3, hrs est Good est - 1, hrs etter etter etter - up to 6% motor efficiency at high power levels with high torque capability est - 1, hrs Good est est - Up to 75% motor efficiency at high power levels est - 1, hrs Premium est Mounting Guidelines: racket options available for mounting consideration (See EZ Mount catalog pages). Hole in the center of the bottom of housing is for manufacturing only not to be used for mounting. Mounting holes are drilled for #6- self-tapping screws with 1/ (6 mm) thread engagement torque to in-lbs. (.5 N-m). Dimensions Port Connections: arbs are sized for 1/" (3 mm) ID tubing, 7- durometer recommended. Flow direction is marked on the pump head with arrows. 1/" ID OR 3/" ID TUING TC-IIS RUSH 1.1 PMDC Iron Core rush 1.1 3.37 5.7.7 NOT TO E USED FOR MOUNTING "G" MOUNTING PATTERN SHOWN (OTHER MOUNTING OPTIONS AVAILALE).7 2.9 22.1 75.7 2X.5 [3.2] MOUNTING HOLES 1.5.1.1 1.
7 Mechanical Integration Dimensions 1/" ID OR 3/" ID TUING 1.1 TC-IIS Series Motor 1.1.7 2. 63.1 "G" MOUNTING PATTERN SHOWN (OTHER MTG OPTIONS AVAILALE) NOT TO E USED FOR MOUNTING.7 2.99 22.1 75.9 2X.5 [3.2] MOUNTING HOLES.1 1. 1.5.1 1/" ID OR 3/" ID TUING 1.1 Motor (High Torque) 1.1.7 NOT TO E USED FOR MOUNTING 3.35 5 "G" MOUNTING PATTERN SHOWN (OTHER MOUNTING OPTIONS AVAILALE) 2.7 6.6.7 22.1 2.99 75.9 2X.5[3.2] MOUNTING HOLES.1 1. 1.5.1
5 TC-IIS Series Dimensions 1/" ID OR 3/" ID TUING 1.1 Motor 1.1.7 NOT TO E USED FOR MOUNTING 3.22 1.7 "G" MOUNTING PATTERN SHOWN (OTHER MTG OPTIONS AVAILALE).7 22.1 2.9 75.7 2X.5 [3.2] MOUNTING HOLES.1 1. 1.5.1 Electrical Integration and Motor Control PMDC Iron Core rush Motor 2 Wire Red (+), lack (-) Wire specification Other Motor Control Considerations 22AWG, Insulation OD.51 in (1. mm), 1 (25 mm) Wire Leads Motor Control Options 2 Wire Red (+), lack (-) 3 Wire (Speed Control) Red (+), lack (-), White (PWM) or Yellow (Analog) Wire (Speed Control & Feedback) Red(+), lack (-), White (PWM) or Yellow (Analog), lue (Tachometer) Wire specification 22AWG, Insulation OD.51 in (1. mm), (5 mm) Wire Leads The drive electronics for the LDC motors are integrated into the motor itself, all that is needed is a power supply with the sufficient voltage and current. Key Things to Remember The pump is not a pressure holding device. An external check valve is recommended, if there is a pressure holding requirement. Pump orientation does not affect performance or life.
9 6 Pulse Width Modulation (PWM) Pulse-width modulation is a commonly used technique for controlling DC motors. TC-IIS Series The average value of the voltage fed to the motor is controlled by turning a switch between the voltage supply and the motor on-and-off at a fast pace. The longer the switch is on compared to the off time, the higher the power supplied to the motor. The PWM switching frequency varies for different types of devices, and is selected based on how it affects the device. For example, some applications require a faster switching frequency to prevent audible noise or electrical noise. The term duty cycle describes the ratio of on-time to the period (one complete on-and-off cycle). Duty cycle is normally expressed as a percentage of on-time, 1% being full-power and 5% being half-power. The advantage of PWM is the reduction of power-loss due to switching versus other control methods. Parker Hannifin recommends controlling the pump using 15kHz - khz frequency range. Typical Flow Diagram Negative Pressure Wound Therapy FILTER OUT TO ATMOSPHERE X-VALVE CHECK VALVE TC-IIS PUMP VENT TO ATMOSPHERE PNEUMATIC PUMP LIQUID ISOLATION FILTER WOUND DRESSING WASTE CANISTER
5 7 TC-IIS Series Typical Flow Diagram Pick-up Head FILTER OUT TO ATMOSPHERE TC-IIS PUMP PNEUMATIC PUMP FILTER PICK-UP HEAD (ACTIVATED) PART Accessory Information Filter-Mufflers also available to assist with filtration and optimize noise reduction..7 [19.]. 5 [5] Part Number: 92-15 (Filters to 1 microns) 2.39 [6.7]
51 Accessory Information EZ Mount available TC-IIS Series EZ Mount provides ease of installation and effective control of vibration transfer. EZ Mount was designed to mount easily to the Precision Fluidic TC-IIS Family of diaphragm pumps. Features Isolation feet on the EZ mount can be rotated in any one of three ninetydegree planes and is designed for top-down or bottom-up mounting providing simple installation. EZ Mount was designed to minimize weight added to the pump assembly. Approximate weights are: Style A -.63 oz (1 g), Style -.71 oz ( g). Effectively absorbs vibration to minimize most vibration-induced noise and vibration transfer into an instrument. Designed to keep height and size to a minimum. Engineered for Parker TC-IIS pumps to ease integration into your system. Physical Properties Operating Environment: 1-15 F (5-7 C) Humidity: - 95% Relative Humidity ase Plate: Noryl GTX Feet: Silicone Feet Insert: rass Hardware: Zinc-Plated Steel Dimensions Style A - Motor 1. 5.6 1.5 7.1 1.1 2.7 62..61 15. 3 POSITIONS IN 9 DEGREE INCREMENTS 1.6 37.1. 21. 1.52 3.5.7 19.9 2.13 5.2 EZ Mount kits include all necessary hardware and detailed instructions. Isolation Feet are available in either threaded or thru-hole clearance for standard #- or #6-32 (M3 for clearance hole only) hardware and can be mounted in any of three ninety-degree planes. Style - PMDC Iron Core rush Motor 1.5 7.1 2.2 3.5 71.7. 3 POSITIONS IN 9 DEGREE INCREMENTS 2.9 63.1 1.1 6 3..3 1.1.51.9. 21. 1.52 3.5
52 9 TC-IIS Series Chemical Compatibility Chart * Chemical Compatibility of Wetted Path Materials Chemical FKM EPDM AEPDM Vectra A1 Air 1 1 1 1 Ozone (1 ppm) 2 Oxygen 1 1 1 1 Ethylene (Ethene) 1 1 3 Acetylene 1 1 1 1 Propane 1 1 Methane 1 1 Nitrogen 1 1 1 1 Carbon Dioxide 1 2 2 1 Halothane (Up to 5%) 1 1 *The above is an Abbreviated Chemical Compatibility Chart. Please consult factory for details. Compatibility Legend 1. EXCELLENT Minimal or no effect 2. GOOD Possible swelling and/or loss of physical properties 3. DOUTFUL Moderate or severe swelling and loss of physical properties. NOT RECOMMENDED Severe effect and should not be considered Note: Consult factory for other gases. Ordering Information TC-IIS Dual Head Pumps - General Purpose Part No. 69 5 6 5 3 12 Free Flow D713-21-1.5 1. 2.7. 5.5.2 3. 2.1 1..9.. D7A-21-1.6 1. 2.5 3.9 5.5.2 3. 2.1 1..9 1. 22. D73-21-1.6 1. 2.. 5.5.2 3. 2.1 1..9 1. 22. D123-21-1.7 1.7 2. 3.9 5.. 3.2 2. 1. 1. 1. 26. D1-21-1.1 1.3 2.3 3.5.6 3.6 2.7 1.5.9.. D713-22-1.5 1. 1.5 2.1 2.6 3.5. D7A-22-1.5 1. 1.5 2.1 2.6 3.5. D73-22-1.5 1. 1.5 2.1 2.6 3.5. D123-22-1..9 1.3 1.7 2.1 2.6. D1-22-1.3.7 1.1 1.5 2. 2.. Part No. 69 5 Vacuum: TC-IIS Dual Head Pumps - High Flow Vacuum: 6 5 3 12 Free Flow D736A-23-2 11. 7.5 5.5.5. D737-23-1 11. 7.5 5.5.5 3.9 3.3. D1-23-1 9.1 7. 6.1.9. D125-23-1 9. 7.2 5..6. D737-22-1.5 1.7 3.7 5.2 7.5 11.. D736-22-2. 2.1 3.6 5. 7.5 1.. D119-22-1. 2.3 3.7 5. 7. 9.3 21. D1-22-1.9 2.2 3. 5. 7.3 9.3 21. 276 276 552 552 Pressure: 27 27 113 Pressure: 113 1379 1379 55 55 Vac Vac Max Max Press Press Motor Type rush PMDC rush PMDC Motor Type VDC PCD* ma Wetted Materials 7 AEPDM, EPDM, EPDM AEPDM, EPDM, EPDM AEPDM, EPDM, EPDM 3 AEPDM, EPDM, EPDM 51 AEPDM, EPDM, EPDM 7 AEPDM, EPDM, EPDM AEPDM, EPDM, EPDM AEPDM, AEPDM, EPDM 5 AEPDM, EPDM, EPDM 37 AEPDM, EPDM, EPDM VDC PCD* ma Diaphragm, Valves, Gasket *PCD: Peak Current Draw Wetted Materials Diaphragm, Valves, Gasket 75 AEPDM, AEPDM, EPDM 15 AEPDM, AEPDM, EPDM 1 AEPDM, AEPDM, EPDM 55 AEPDM, AEPDM, EPDM 1 AEPDM, AEPDM, EPDM 75 AEPDM, AEPDM, EPDM 6 AEPDM, AEPDM, EPDM 5 AEPDM, AEPDM, EPDM TC-IIS Dual Head - High Pressure or Vacuum Vacuum: Pressure: Part No. FF Max PCD* Wetted Materials
D123-21-1.7 1.7 2. 3.9 5.. 3.2 2. 1. 1. 1. 26. D1-21-1.1 1.3 2.3 3.5.6 3.6 2.7 1.5.9.. D713-22-1.5 1. 1.5 2.1 2.6 3.5. D7A-22-1.5 1. 1.5 2.1 2.6 3.5. Ordering Information D73-22-1.5 1. 1.5 2.1 2.6 3.5. D123-22-1..9 1.3 1.7 2.1 2.6. D1-22-1.3.7 1.1 1.5 2. 2.. PMDC rush PMDC 3 AEPDM, EPDM, EPDM 51 AEPDM, EPDM, EPDM 7 AEPDM, EPDM, EPDM AEPDM, EPDM, EPDM TC-IIS Series AEPDM, AEPDM, EPDM 5 AEPDM, EPDM, EPDM 37 AEPDM, EPDM, EPDM 53 1 TC-IIS Dual Head Pumps - High Flow Part No. 69 5 6 5 3 12 Free Flow D736A-23-2 11. 7.5 5.5.5. D737-23-1 11. 7.5 5.5.5 3.9 3.3. D1-23-1 9.1 7. 6.1.9. D125-23-1 9. 7.2 5..6. D737-22-1.5 1.7 3.7 5.2 7.5 11.. D736-22-2. 2.1 3.6 5. 7.5 1.. D119-22-1. 2.3 3.7 5. 7. 9.3 21. D1-22-1.9 2.2 3. 5. 7.3 9.3 21. 276 552 27 113 1379 55 PCD* Wetted Materials 75 AEPDM, AEPDM, EPDM 15 AEPDM, AEPDM, EPDM 1 AEPDM, AEPDM, EPDM 55 AEPDM, AEPDM, EPDM 1 AEPDM, AEPDM, EPDM 75 AEPDM, AEPDM, EPDM 6 AEPDM, AEPDM, EPDM 5 AEPDM, AEPDM, EPDM Vacuum: Pressure: Part No. FF Max PCD* Wetted Materials 69 5 Vacuum: TC-IIS Dual Head - High Pressure or Vacuum 6 5 3 12 D1-23-1 2. 2. 1.6 1.3 1.1. 5. D76A-22-1.1.5 1. 1. 1. 2. 3.1 26. D75C-22-1.1.5 1. 1. 1. 2. 3.1 26. 552 113 Pressure: Note: The Ordering Information Section includes a few selected part numbers for the product line. Other performances and configurations are available. Please contact your Sales Representative or an Application Engineer to discuss your application needs. 55 32 26 275 5 313 Vac Vac Max Press Press Motor Type Motor Type VDC VDC ma ma Diaphragm, Valves, Gasket *PCD: Peak Current Draw Diaphragm, Valves, Gasket 6 AEPDM, EPDM, EPDM AEPDM, AEPDM, EPDM 5 AEPDM, AEPDM, EPDM *PCD: Peak Current Draw Accessory Information Part No. Rev Date_5/9/5 92-15 1 Filtering Level (Micron) Filter Area 1.71 in 2 (11 cm 2 ) Internal Volume. in 3 (3.9 cm 3 ) Max Temperature C Filter-Mufflers: To assist with filtration and optimize noise reduction. Tubing: Recommendation 1/" (3mm) ID. Operating Limitations: Min Temperature 32 C Max Pressure Pressure 65 PSI (. 65 PSI bar) Wetted Materials Polypropylene
5 11 TC-IIS Series Ordering Information EZ Mount for TC-IIS with PMDC Iron Core rush Motor Part Number Style Description 332-1-A5S 332-1-5S 332-1-D5S 332-1-C5S EZ Mount for TC-IIS with (High Torque) Motor Part Number Style Description 331-1-A5S 331-1-5S 331-1-D5S 331-1-C5S #- Threaded # Clearance #6-32 Threaded #6 / M3 Clearance #- Threaded # Clearance #6-32 Threaded #6 / M3 Clearance EZ Mount for TC-IIS with Motor Part Number Style 32-1-A5S 32-1-5S 32-1-D5S 32-1-C5S EZ Mount for TC-IIS with Motor Part Number 17-1-A5S 17-1-5S 17-1-D5S 17-1-C5S Style A A A A Description #- Threaded # Clearance #6-32 Threaded #6 / M3 Clearance Description #- Threaded # Clearance #6-32 Threaded #6 / M3 Clearance Please click on the Order On-line button below (or go to www.parker.com/precisionfluidics/btciis) to configure the TC-IIS Miniature Diaphragm Pump for your application. Serviceable PPF products are designed for use through the rated life and Parker does not sell replacement parts, nor is it recommended to service these in the field Note: In addition to Parker s innovative and flexible pump designs, we offer applications engineering expertise to our customers in order to configure and recommend the optimal pump for the application. Contact Parker Applications Engineering to discuss and configure alternate pump configurations to meet your specific application requirements. Providing information on the following requirements will assist us in developing an optimal solution for your application: Noise Operating Pressure / Vacuum Power Consumption Life Requirement Description of pump function in the application Size Motor Control Media Voltage ORDER ON-LINE
55 TC-IIS Series Appendix A All performance data is typical based on standard conditions: 7 F and 1.7 psia (21 C and 1 bar). 1. Duty Dependent. For operation above 2 F (5 C) consult factory 2. Noise is dependent on the configuration and operation of the pump in the application. Parker has the ability to tailor the pump configuration when noise is a critical criterion in the effort to meet the performance requirements of the application. Noise level is tested to Parker protocol P-15. 3. Life rating can vary depending on application and operating conditions.. Custom motor options available. Custom motors may require a significant application potential. The standard motors can be configured with a special winding to meet a particular operation point at a specified voltage 5. Current range is dependent on motor type, voltage, pressure/vacuum and flow requirement. Lower levels possible depending on application. 6. Pump efficiency is a measure of the flow rate generated per unit of power consumed. Efficiency may change dependent on application and operating condition at free flow. 13 Parker Hannifin Corporation PPF MDP - 2/US October 13 Parker Hannifin Corporation Precision Fluidics Division 26 Clinton Dr., Unit 13 Hollis, NH 9 phone: +1 63 595 15 email: ppfinfo@parker.com www.parker.com/precisionfluidics